From: Vishal Kulkarni <vishal@chelsio.com>
To: netdev@vger.kernel.org, davem@davemloft.net
Cc: nirranjan@chelsio.com, dt@chelsio.com,
Vishal Kulkarni <vishal@chelsio.com>
Subject: [PATCH net-next v2 1/5] cxgb4: update set_flash to flash different images
Date: Thu, 18 Jun 2020 11:35:52 +0530 [thread overview]
Message-ID: <20200618060556.14410-2-vishal@chelsio.com> (raw)
In-Reply-To: <20200618060556.14410-1-vishal@chelsio.com>
Chelsio adapter contains different flash regions and each
region is used by different binary files. This patch adds
support to flash images like PHY firmware, boot and boot config
using ethtool -f N.
The N value mapping is as follows.
N = 0 : Parse image and decide which region to flash
N = 1 : Firmware
N = 2 : PHY firmware
N = 3 : boot image
N = 4 : boot cfg
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
---
drivers/net/ethernet/chelsio/cxgb4/cxgb4.h | 9 ++
.../ethernet/chelsio/cxgb4/cxgb4_ethtool.c | 121 +++++++++++++++---
2 files changed, 115 insertions(+), 15 deletions(-)
diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h b/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h
index cf69c6edcfec..a7a1e1f5d554 100644
--- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h
+++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4.h
@@ -139,6 +139,10 @@ enum cc_fec {
FEC_BASER_RS = 1 << 2 /* BaseR/Reed-Solomon */
};
+enum {
+ CXGB4_ETHTOOL_FLASH_FW = 1,
+};
+
struct port_stats {
u64 tx_octets; /* total # of octets in good frames */
u64 tx_frames; /* all good frames */
@@ -492,6 +496,11 @@ struct trace_params {
unsigned char port;
};
+struct cxgb4_fw_data {
+ __be32 signature;
+ __u8 reserved[4];
+};
+
/* Firmware Port Capabilities types. */
typedef u16 fw_port_cap16_t; /* 16-bit Port Capabilities integral value */
diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_ethtool.c b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_ethtool.c
index 9fd496732b2c..92f79d0cd6ab 100644
--- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_ethtool.c
+++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_ethtool.c
@@ -23,6 +23,11 @@ static void set_msglevel(struct net_device *dev, u32 val)
netdev2adap(dev)->msg_enable = val;
}
+static const char * const flash_region_strings[] = {
+ "All",
+ "Firmware",
+};
+
static const char stats_strings[][ETH_GSTRING_LEN] = {
"tx_octets_ok ",
"tx_frames_ok ",
@@ -1235,15 +1240,88 @@ static int set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom,
return err;
}
-static int set_flash(struct net_device *netdev, struct ethtool_flash *ef)
+static int cxgb4_ethtool_flash_fw(struct net_device *netdev,
+ const u8 *data, u32 size)
{
- int ret;
- const struct firmware *fw;
struct adapter *adap = netdev2adap(netdev);
unsigned int mbox = PCIE_FW_MASTER_M + 1;
- u32 pcie_fw;
+ int ret;
+
+ /* If the adapter has been fully initialized then we'll go ahead and
+ * try to get the firmware's cooperation in upgrading to the new
+ * firmware image otherwise we'll try to do the entire job from the
+ * host ... and we always "force" the operation in this path.
+ */
+ if (adap->flags & CXGB4_FULL_INIT_DONE)
+ mbox = adap->mbox;
+
+ ret = t4_fw_upgrade(adap, mbox, data, size, 1);
+ if (ret)
+ dev_err(adap->pdev_dev,
+ "Failed to flash firmware\n");
+
+ return ret;
+}
+
+static int cxgb4_ethtool_flash_region(struct net_device *netdev,
+ const u8 *data, u32 size, u32 region)
+{
+ struct adapter *adap = netdev2adap(netdev);
+ int ret;
+
+ switch (region) {
+ case CXGB4_ETHTOOL_FLASH_FW:
+ ret = cxgb4_ethtool_flash_fw(netdev, data, size);
+ break;
+ default:
+ ret = -EOPNOTSUPP;
+ break;
+ }
+
+ if (!ret)
+ dev_info(adap->pdev_dev,
+ "loading %s successful, reload cxgb4 driver\n",
+ flash_region_strings[region]);
+ return ret;
+}
+
+#define CXGB4_FW_SIG 0x4368656c
+#define CXGB4_FW_SIG_OFFSET 0x160
+
+static int cxgb4_validate_fw_image(const u8 *data, u32 *size)
+{
+ struct cxgb4_fw_data *header;
+
+ header = (struct cxgb4_fw_data *)&data[CXGB4_FW_SIG_OFFSET];
+ if (be32_to_cpu(header->signature) != CXGB4_FW_SIG)
+ return -EINVAL;
+
+ if (size)
+ *size = be16_to_cpu(((struct fw_hdr *)data)->len512) * 512;
+
+ return 0;
+}
+
+static int cxgb4_ethtool_get_flash_region(const u8 *data, u32 *size)
+{
+ if (!cxgb4_validate_fw_image(data, size))
+ return CXGB4_ETHTOOL_FLASH_FW;
+
+ return -EOPNOTSUPP;
+}
+
+static int set_flash(struct net_device *netdev, struct ethtool_flash *ef)
+{
+ struct adapter *adap = netdev2adap(netdev);
+ const struct firmware *fw;
unsigned int master;
u8 master_vld = 0;
+ const u8 *fw_data;
+ size_t fw_size;
+ u32 size = 0;
+ u32 pcie_fw;
+ int region;
+ int ret;
pcie_fw = t4_read_reg(adap, PCIE_FW_A);
master = PCIE_FW_MASTER_G(pcie_fw);
@@ -1261,19 +1339,32 @@ static int set_flash(struct net_device *netdev, struct ethtool_flash *ef)
if (ret < 0)
return ret;
- /* If the adapter has been fully initialized then we'll go ahead and
- * try to get the firmware's cooperation in upgrading to the new
- * firmware image otherwise we'll try to do the entire job from the
- * host ... and we always "force" the operation in this path.
- */
- if (adap->flags & CXGB4_FULL_INIT_DONE)
- mbox = adap->mbox;
+ fw_data = fw->data;
+ fw_size = fw->size;
+ if (ef->region == ETHTOOL_FLASH_ALL_REGIONS) {
+ while (fw_size > 0) {
+ size = 0;
+ region = cxgb4_ethtool_get_flash_region(fw_data, &size);
+ if (region < 0 || !size) {
+ ret = region;
+ goto out_free_fw;
+ }
+
+ ret = cxgb4_ethtool_flash_region(netdev, fw_data, size,
+ region);
+ if (ret)
+ goto out_free_fw;
+
+ fw_data += size;
+ fw_size -= size;
+ }
+ } else {
+ ret = cxgb4_ethtool_flash_region(netdev, fw_data, fw_size,
+ ef->region);
+ }
- ret = t4_fw_upgrade(adap, mbox, fw->data, fw->size, 1);
+out_free_fw:
release_firmware(fw);
- if (!ret)
- dev_info(adap->pdev_dev,
- "loaded firmware %s, reload cxgb4 driver\n", ef->data);
return ret;
}
--
2.21.1
next prev parent reply other threads:[~2020-06-18 6:07 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-18 6:05 [PATCH net-next v2 0/5] cxgb4: add support to read/write flash Vishal Kulkarni
2020-06-18 6:05 ` Vishal Kulkarni [this message]
2020-06-18 6:05 ` [PATCH net-next v2 2/5] cxgb4: add support to flash PHY image Vishal Kulkarni
2020-06-18 6:05 ` [PATCH net-next v2 3/5] cxgb4: add support to flash boot image Vishal Kulkarni
2020-06-18 6:05 ` [PATCH net-next v2 4/5] cxgb4: add support to flash boot cfg image Vishal Kulkarni
2020-06-18 6:05 ` [PATCH net-next v2 5/5] cxgb4: add support to read serial flash Vishal Kulkarni
2020-06-19 3:50 ` [PATCH net-next v2 0/5] cxgb4: add support to read/write flash David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200618060556.14410-2-vishal@chelsio.com \
--to=vishal@chelsio.com \
--cc=davem@davemloft.net \
--cc=dt@chelsio.com \
--cc=netdev@vger.kernel.org \
--cc=nirranjan@chelsio.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox