[PATCH AUTOSEL 5.4 05/18] mac80211: allow rx of mesh eapol frames with default rx key

[PATCH AUTOSEL 5.4 05/18] mac80211: allow rx of mesh eapol frames with default rx key

[Sasha Levin]

From: Markus Theil <markus.theil@tu-ilmenau.de>

[ Upstream commit 0b467b63870d9c05c81456aa9bfee894ab2db3b6 ]

Without this patch, eapol frames cannot be received in mesh
mode, when 802.1X should be used. Initially only a MGTK is
defined, which is found and set as rx->key, when there are
no other keys set. ieee80211_drop_unencrypted would then
drop these eapol frames, as they are data frames without
encryption and there exists some rx->key.

Fix this by differentiating between mesh eapol frames and
other data frames with existing rx->key. Allow mesh mesh
eapol frames only if they are for our vif address.

With this patch in-place, ieee80211_rx_h_mesh_fwding continues
after the ieee80211_drop_unencrypted check and notices, that
these eapol frames have to be delivered locally, as they should.

Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200625104214.50319-1-markus.theil@tu-ilmenau.de
[small code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/mac80211/rx.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/net/mac80211/rx.c b/net/mac80211/rx.c
index 69429c8df7b30..e5fb9002d3147 100644
--- a/net/mac80211/rx.c
+++ b/net/mac80211/rx.c
@@ -2305,6 +2305,7 @@ static int ieee80211_802_1x_port_control(struct ieee80211_rx_data *rx)
 
 static int ieee80211_drop_unencrypted(struct ieee80211_rx_data *rx, __le16 fc)
 {
+	struct ieee80211_hdr *hdr = (void *)rx->skb->data;
 	struct sk_buff *skb = rx->skb;
 	struct ieee80211_rx_status *status = IEEE80211_SKB_RXCB(skb);
 
@@ -2315,6 +2316,31 @@ static int ieee80211_drop_unencrypted(struct ieee80211_rx_data *rx, __le16 fc)
 	if (status->flag & RX_FLAG_DECRYPTED)
 		return 0;
 
+	/* check mesh EAPOL frames first */
+	if (unlikely(rx->sta && ieee80211_vif_is_mesh(&rx->sdata->vif) &&
+		     ieee80211_is_data(fc))) {
+		struct ieee80211s_hdr *mesh_hdr;
+		u16 hdr_len = ieee80211_hdrlen(fc);
+		u16 ethertype_offset;
+		__be16 ethertype;
+
+		if (!ether_addr_equal(hdr->addr1, rx->sdata->vif.addr))
+			goto drop_check;
+
+		/* make sure fixed part of mesh header is there, also checks skb len */
+		if (!pskb_may_pull(rx->skb, hdr_len + 6))
+			goto drop_check;
+
+		mesh_hdr = (struct ieee80211s_hdr *)(skb->data + hdr_len);
+		ethertype_offset = hdr_len + ieee80211_get_mesh_hdrlen(mesh_hdr) +
+				   sizeof(rfc1042_header);
+
+		if (skb_copy_bits(rx->skb, ethertype_offset, &ethertype, 2) == 0 &&
+		    ethertype == rx->sdata->control_port_protocol)
+			return 0;
+	}
+
+drop_check:
 	/* Drop unencrypted frames if key is set. */
 	if (unlikely(!ieee80211_has_protected(fc) &&
 		     !ieee80211_is_any_nullfunc(fc) &&
-- 
2.25.1

[PATCH AUTOSEL 5.4 10/18] drivers/net/wan/lapbether: Fixed the value of hard_header_len

[Sasha Levin]

From: Xie He <xie.he.0141@gmail.com>

[ Upstream commit 9dc829a135fb5927f1519de11286e2bbb79f5b66 ]

When this driver transmits data,
  first this driver will remove a pseudo header of 1 byte,
  then the lapb module will prepend the LAPB header of 2 or 3 bytes,
  then this driver will prepend a length field of 2 bytes,
  then the underlying Ethernet device will prepend its own header.

So, the header length required should be:
  -1 + 3 + 2 + "the header length needed by the underlying device".

This patch fixes kernel panic when this driver is used with AF_PACKET
SOCK_DGRAM sockets.

Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wan/lapbether.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wan/lapbether.c b/drivers/net/wan/lapbether.c
index 0f1217b506ad2..5a6f27298b90f 100644
--- a/drivers/net/wan/lapbether.c
+++ b/drivers/net/wan/lapbether.c
@@ -303,7 +303,6 @@ static void lapbeth_setup(struct net_device *dev)
 	dev->netdev_ops	     = &lapbeth_netdev_ops;
 	dev->needs_free_netdev = true;
 	dev->type            = ARPHRD_X25;
-	dev->hard_header_len = 3;
 	dev->mtu             = 1000;
 	dev->addr_len        = 0;
 }
@@ -324,6 +323,14 @@ static int lapbeth_new_device(struct net_device *dev)
 	if (!ndev)
 		goto out;
 
+	/* When transmitting data:
+	 * first this driver removes a pseudo header of 1 byte,
+	 * then the lapb module prepends an LAPB header of at most 3 bytes,
+	 * then this driver prepends a length field of 2 bytes,
+	 * then the underlying Ethernet device prepends its own header.
+	 */
+	ndev->hard_header_len = -1 + 3 + 2 + dev->hard_header_len;
+
 	lapbeth = netdev_priv(ndev);
 	lapbeth->axdev = ndev;
 
-- 
2.25.1

[PATCH AUTOSEL 5.4 12/18] net: usb: qmi_wwan: add support for Quectel EG95 LTE modem

[Sasha Levin]

From: AceLan Kao <acelan.kao@canonical.com>

[ Upstream commit f815dd5cf48b905eeecf0a2b990e9b7ab048b4f1 ]

Add support for Quectel Wireless Solutions Co., Ltd. EG95 LTE modem

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  5 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0195 Rev=03.18
S:  Manufacturer=Android
S:  Product=Android
C:  #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/qmi_wwan.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/usb/qmi_wwan.c b/drivers/net/usb/qmi_wwan.c
index 4a2c7355be63d..e57d59b0a7ae9 100644
--- a/drivers/net/usb/qmi_wwan.c
+++ b/drivers/net/usb/qmi_wwan.c
@@ -1370,6 +1370,7 @@ static const struct usb_device_id products[] = {
 	{QMI_QUIRK_SET_DTR(0x1e0e, 0x9001, 5)},	/* SIMCom 7100E, 7230E, 7600E ++ */
 	{QMI_QUIRK_SET_DTR(0x2c7c, 0x0121, 4)},	/* Quectel EC21 Mini PCIe */
 	{QMI_QUIRK_SET_DTR(0x2c7c, 0x0191, 4)},	/* Quectel EG91 */
+	{QMI_QUIRK_SET_DTR(0x2c7c, 0x0195, 4)},	/* Quectel EG95 */
 	{QMI_FIXED_INTF(0x2c7c, 0x0296, 4)},	/* Quectel BG96 */
 	{QMI_QUIRK_SET_DTR(0x2cb7, 0x0104, 4)},	/* Fibocom NL678 series */
 	{QMI_FIXED_INTF(0x0489, 0xe0b4, 0)},	/* Foxconn T77W968 LTE */
-- 
2.25.1

[PATCH AUTOSEL 5.4 13/18] net: sky2: initialize return of gm_phy_read

[Sasha Levin]

From: Tom Rix <trix@redhat.com>

[ Upstream commit 28b18e4eb515af7c6661c3995c6e3c34412c2874 ]

clang static analysis flags this garbage return

drivers/net/ethernet/marvell/sky2.c:208:2: warning: Undefined or garbage value returned to caller [core.uninitialized.UndefReturn]
        return v;
        ^~~~~~~~

static inline u16 gm_phy_read( ...
{
	u16 v;
	__gm_phy_read(hw, port, reg, &v);
	return v;
}

__gm_phy_read can return without setting v.

So handle similar to skge.c's gm_phy_read, initialize v.

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/marvell/sky2.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/marvell/sky2.c b/drivers/net/ethernet/marvell/sky2.c
index 5f56ee83e3b10..df7c23cd33600 100644
--- a/drivers/net/ethernet/marvell/sky2.c
+++ b/drivers/net/ethernet/marvell/sky2.c
@@ -203,7 +203,7 @@ static int __gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg, u16 *val)
 
 static inline u16 gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg)
 {
-	u16 v;
+	u16 v = 0;
 	__gm_phy_read(hw, port, reg, &v);
 	return v;
 }
-- 
2.25.1