[PATCH AUTOSEL 4.9 1/7] usb: hso: Fix debug compile warning on sparc32

[PATCH AUTOSEL 4.9 1/7] usb: hso: Fix debug compile warning on sparc32

[Sasha Levin]

From: Geert Uytterhoeven <geert@linux-m68k.org>

[ Upstream commit e0484010ec05191a8edf980413fc92f28050c1cc ]

On sparc32, tcflag_t is "unsigned long", unlike on all other
architectures, where it is "unsigned int":

    drivers/net/usb/hso.c: In function ‘hso_serial_set_termios’:
    include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 4 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
    drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
       hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
       ^~~~~~~
    include/linux/kern_levels.h:5:18: warning: format ‘%d’ expects argument of type ‘unsigned int’, but argument 5 has type ‘tcflag_t {aka long unsigned int}’ [-Wformat=]
    drivers/net/usb/hso.c:1393:3: note: in expansion of macro ‘hso_dbg’
       hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
       ^~~~~~~

As "unsigned long" is 32-bit on sparc32, fix this by casting all tcflag_t
parameters to "unsigned int".
While at it, use "%u" to format unsigned numbers.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/hso.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/net/usb/hso.c b/drivers/net/usb/hso.c
index 27fc699d8be5b..2ae30db06bfa1 100644
--- a/drivers/net/usb/hso.c
+++ b/drivers/net/usb/hso.c
@@ -1404,8 +1404,9 @@ static void hso_serial_set_termios(struct tty_struct *tty, struct ktermios *old)
 	unsigned long flags;
 
 	if (old)
-		hso_dbg(0x16, "Termios called with: cflags new[%d] - old[%d]\n",
-			tty->termios.c_cflag, old->c_cflag);
+		hso_dbg(0x16, "Termios called with: cflags new[%u] - old[%u]\n",
+			(unsigned int)tty->termios.c_cflag,
+			(unsigned int)old->c_cflag);
 
 	/* the actual setup */
 	spin_lock_irqsave(&serial->serial_lock, flags);
-- 
2.25.1

[PATCH AUTOSEL 4.9 2/7] qed: Disable "MFW indication via attention" SPAM every 5 minutes

[Sasha Levin]

From: Laurence Oberman <loberman@redhat.com>

[ Upstream commit 1d61e21852d3161f234b9656797669fe185c251b ]

This is likely firmware causing this but its starting to annoy customers.
Change the message level to verbose to prevent the spam.
Note that this seems to only show up with ISCSI enabled on the HBA via the
qedi driver.

Signed-off-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/qlogic/qed/qed_int.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/qlogic/qed/qed_int.c b/drivers/net/ethernet/qlogic/qed/qed_int.c
index fd19372db2f86..6e1d38041d0ac 100644
--- a/drivers/net/ethernet/qlogic/qed/qed_int.c
+++ b/drivers/net/ethernet/qlogic/qed/qed_int.c
@@ -2158,7 +2158,8 @@ static int qed_int_attentions(struct qed_hwfn *p_hwfn)
 			index, attn_bits, attn_acks, asserted_bits,
 			deasserted_bits, p_sb_attn_sw->known_attn);
 	} else if (asserted_bits == 0x100) {
-		DP_INFO(p_hwfn, "MFW indication via attention\n");
+		DP_VERBOSE(p_hwfn, NETIF_MSG_INTR,
+			   "MFW indication via attention\n");
 	} else {
 		DP_VERBOSE(p_hwfn, NETIF_MSG_INTR,
 			   "MFW indication [deassertion]\n");
-- 
2.25.1

[PATCH AUTOSEL 4.9 3/7] nfc: s3fwrn5: add missing release on skb in s3fwrn5_recv_frame

[Sasha Levin]

From: Navid Emamdoost <navid.emamdoost@gmail.com>

[ Upstream commit 1e8fd3a97f2d83a7197876ceb4f37b4c2b00a0f3 ]

The implementation of s3fwrn5_recv_frame() is supposed to consume skb on
all execution paths. Release skb before returning -ENODEV.

Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/nfc/s3fwrn5/core.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/nfc/s3fwrn5/core.c b/drivers/nfc/s3fwrn5/core.c
index 9d9c8d57a042d..64b58455e620b 100644
--- a/drivers/nfc/s3fwrn5/core.c
+++ b/drivers/nfc/s3fwrn5/core.c
@@ -209,6 +209,7 @@ int s3fwrn5_recv_frame(struct nci_dev *ndev, struct sk_buff *skb,
 	case S3FWRN5_MODE_FW:
 		return s3fwrn5_fw_recv_frame(ndev, skb);
 	default:
+		kfree_skb(skb);
 		return -ENODEV;
 	}
 }
-- 
2.25.1

[PATCH AUTOSEL 4.9 5/7] net: ethernet: ravb: exit if re-initialization fails in tx timeout

[Sasha Levin]

From: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>

[ Upstream commit 015c5d5e6aa3523c758a70eb87b291cece2dbbb4 ]

According to the report of [1], this driver is possible to cause
the following error in ravb_tx_timeout_work().

ravb e6800000.ethernet ethernet: failed to switch device to config mode

This error means that the hardware could not change the state
from "Operation" to "Configuration" while some tx and/or rx queue
are operating. After that, ravb_config() in ravb_dmac_init() will fail,
and then any descriptors will be not allocaled anymore so that NULL
pointer dereference happens after that on ravb_start_xmit().

To fix the issue, the ravb_tx_timeout_work() should check
the return values of ravb_stop_dma() and ravb_dmac_init().
If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX
and just exits. If ravb_dmac_init() fails, just exits.

[1]
https://lore.kernel.org/linux-renesas-soc/20200518045452.2390-1-dirk.behme@de.bosch.com/

Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/renesas/ravb_main.c | 26 ++++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c
index 545cb6262cffd..93d3152752ff4 100644
--- a/drivers/net/ethernet/renesas/ravb_main.c
+++ b/drivers/net/ethernet/renesas/ravb_main.c
@@ -1444,6 +1444,7 @@ static void ravb_tx_timeout_work(struct work_struct *work)
 	struct ravb_private *priv = container_of(work, struct ravb_private,
 						 work);
 	struct net_device *ndev = priv->ndev;
+	int error;
 
 	netif_tx_stop_all_queues(ndev);
 
@@ -1452,15 +1453,36 @@ static void ravb_tx_timeout_work(struct work_struct *work)
 		ravb_ptp_stop(ndev);
 
 	/* Wait for DMA stopping */
-	ravb_stop_dma(ndev);
+	if (ravb_stop_dma(ndev)) {
+		/* If ravb_stop_dma() fails, the hardware is still operating
+		 * for TX and/or RX. So, this should not call the following
+		 * functions because ravb_dmac_init() is possible to fail too.
+		 * Also, this should not retry ravb_stop_dma() again and again
+		 * here because it's possible to wait forever. So, this just
+		 * re-enables the TX and RX and skip the following
+		 * re-initialization procedure.
+		 */
+		ravb_rcv_snd_enable(ndev);
+		goto out;
+	}
 
 	ravb_ring_free(ndev, RAVB_BE);
 	ravb_ring_free(ndev, RAVB_NC);
 
 	/* Device init */
-	ravb_dmac_init(ndev);
+	error = ravb_dmac_init(ndev);
+	if (error) {
+		/* If ravb_dmac_init() fails, descriptors are freed. So, this
+		 * should return here to avoid re-enabling the TX and RX in
+		 * ravb_emac_init().
+		 */
+		netdev_err(ndev, "%s: ravb_dmac_init() failed, error %d\n",
+			   __func__, error);
+		return;
+	}
 	ravb_emac_init(ndev);
 
+out:
 	/* Initialise PTP Clock driver */
 	if (priv->chip_id == RCAR_GEN2)
 		ravb_ptp_init(ndev, priv->pdev);
-- 
2.25.1

[PATCH AUTOSEL 4.9 7/7] xen-netfront: fix potential deadlock in xennet_remove()

[Sasha Levin]

From: Andrea Righi <andrea.righi@canonical.com>

[ Upstream commit c2c633106453611be07821f53dff9e93a9d1c3f0 ]

There's a potential race in xennet_remove(); this is what the driver is
doing upon unregistering a network device:

  1. state = read bus state
  2. if state is not "Closed":
  3.    request to set state to "Closing"
  4.    wait for state to be set to "Closing"
  5.    request to set state to "Closed"
  6.    wait for state to be set to "Closed"

If the state changes to "Closed" immediately after step 1 we are stuck
forever in step 4, because the state will never go back from "Closed" to
"Closing".

Make sure to check also for state == "Closed" in step 4 to prevent the
deadlock.

Also add a 5 sec timeout any time we wait for the bus state to change,
to avoid getting stuck forever in wait_event().

Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/xen-netfront.c | 64 +++++++++++++++++++++++++-------------
 1 file changed, 42 insertions(+), 22 deletions(-)

diff --git a/drivers/net/xen-netfront.c b/drivers/net/xen-netfront.c
index 6d391a268469f..ceaf6b30d683d 100644
--- a/drivers/net/xen-netfront.c
+++ b/drivers/net/xen-netfront.c
@@ -62,6 +62,8 @@ module_param_named(max_queues, xennet_max_queues, uint, 0644);
 MODULE_PARM_DESC(max_queues,
 		 "Maximum number of queues per virtual interface");
 
+#define XENNET_TIMEOUT  (5 * HZ)
+
 static const struct ethtool_ops xennet_ethtool_ops;
 
 struct netfront_cb {
@@ -1355,12 +1357,15 @@ static struct net_device *xennet_create_dev(struct xenbus_device *dev)
 
 	netif_carrier_off(netdev);
 
-	xenbus_switch_state(dev, XenbusStateInitialising);
-	wait_event(module_wq,
-		   xenbus_read_driver_state(dev->otherend) !=
-		   XenbusStateClosed &&
-		   xenbus_read_driver_state(dev->otherend) !=
-		   XenbusStateUnknown);
+	do {
+		xenbus_switch_state(dev, XenbusStateInitialising);
+		err = wait_event_timeout(module_wq,
+				 xenbus_read_driver_state(dev->otherend) !=
+				 XenbusStateClosed &&
+				 xenbus_read_driver_state(dev->otherend) !=
+				 XenbusStateUnknown, XENNET_TIMEOUT);
+	} while (!err);
+
 	return netdev;
 
  exit:
@@ -2172,28 +2177,43 @@ static const struct attribute_group xennet_dev_group = {
 };
 #endif /* CONFIG_SYSFS */
 
-static int xennet_remove(struct xenbus_device *dev)
+static void xennet_bus_close(struct xenbus_device *dev)
 {
-	struct netfront_info *info = dev_get_drvdata(&dev->dev);
-
-	dev_dbg(&dev->dev, "%s\n", dev->nodename);
+	int ret;
 
-	if (xenbus_read_driver_state(dev->otherend) != XenbusStateClosed) {
+	if (xenbus_read_driver_state(dev->otherend) == XenbusStateClosed)
+		return;
+	do {
 		xenbus_switch_state(dev, XenbusStateClosing);
-		wait_event(module_wq,
-			   xenbus_read_driver_state(dev->otherend) ==
-			   XenbusStateClosing ||
-			   xenbus_read_driver_state(dev->otherend) ==
-			   XenbusStateUnknown);
+		ret = wait_event_timeout(module_wq,
+				   xenbus_read_driver_state(dev->otherend) ==
+				   XenbusStateClosing ||
+				   xenbus_read_driver_state(dev->otherend) ==
+				   XenbusStateClosed ||
+				   xenbus_read_driver_state(dev->otherend) ==
+				   XenbusStateUnknown,
+				   XENNET_TIMEOUT);
+	} while (!ret);
+
+	if (xenbus_read_driver_state(dev->otherend) == XenbusStateClosed)
+		return;
 
+	do {
 		xenbus_switch_state(dev, XenbusStateClosed);
-		wait_event(module_wq,
-			   xenbus_read_driver_state(dev->otherend) ==
-			   XenbusStateClosed ||
-			   xenbus_read_driver_state(dev->otherend) ==
-			   XenbusStateUnknown);
-	}
+		ret = wait_event_timeout(module_wq,
+				   xenbus_read_driver_state(dev->otherend) ==
+				   XenbusStateClosed ||
+				   xenbus_read_driver_state(dev->otherend) ==
+				   XenbusStateUnknown,
+				   XENNET_TIMEOUT);
+	} while (!ret);
+}
+
+static int xennet_remove(struct xenbus_device *dev)
+{
+	struct netfront_info *info = dev_get_drvdata(&dev->dev);
 
+	xennet_bus_close(dev);
 	xennet_disconnect_backend(info);
 
 	if (info->netdev->reg_state == NETREG_REGISTERED)
-- 
2.25.1