* vxlan_asymmetric.sh test failed every time
@ 2020-10-13 4:39 Hangbin Liu
2020-10-13 7:49 ` Ido Schimmel
0 siblings, 1 reply; 4+ messages in thread
From: Hangbin Liu @ 2020-10-13 4:39 UTC (permalink / raw)
To: Ido Schimmel; +Cc: Network Development, David Ahern
Hi Ido,
When run vxlan_asymmetric.sh on RHEL8, It failed every time. I though that
it may failed because the kernel version is too old. But today I tried with
latest kernel, it still failed. Would you please help check if I missed
any configuration?
# uname -r
5.9.0
# ip -V
ip utility, iproute2-ss200602
# netsniff-ng -v
netsniff-ng 0.6.6 (Syro), Git id: (none)
# cp forwarding.config.sample forwarding.config
# ./vxlan_asymmetric.sh
RTNETLINK answers: File exists
TEST: ping: local->local vid 10->vid 20 [FAIL]
TEST: ping: local->remote vid 10->vid 10 [ OK ]
TEST: ping: local->remote vid 20->vid 20 [ OK ]
TEST: ping: local->remote vid 10->vid 20 [FAIL]
TEST: ping: local->remote vid 20->vid 10 [FAIL]
INFO: deleting neighbours from vlan interfaces
TEST: ping: local->local vid 10->vid 20 [FAIL]
TEST: ping: local->remote vid 10->vid 10 [ OK ]
TEST: ping: local->remote vid 20->vid 20 [ OK ]
TEST: ping: local->remote vid 10->vid 20 [FAIL]
TEST: ping: local->remote vid 20->vid 10 [FAIL]
TEST: neigh_suppress: on / neigh exists: yes [ OK ]
TEST: neigh_suppress: on / neigh exists: no [ OK ]
TEST: neigh_suppress: off / neigh exists: no [ OK ]
TEST: neigh_suppress: off / neigh exists: yes [ OK ]
# dmesg
[...snip...]
[ 1518.885526] device br1 entered promiscuous mode
[ 1518.886211] device br1 left promiscuous mode
[ 1518.890637] device br1 entered promiscuous mode
[ 1518.941524] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
[ 1518.949522] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
[ 1519.165569] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
[ 1519.166900] IPv6: vlan10-v: IPv6 duplicate address fe80::200:5eff:fe00:101 used by 00:00:5e:00:01:01 detected!
[ 1519.392633] br1: received packet on vx20 with own address as source address (addr:00:00:5e:00:01:01, vlan:20)
[ 1519.741559] br1: received packet on vx20 with own address as source address (addr:00:00:5e:00:01:01, vlan:20)
[ 1519.861641] br1: received packet on vx20 with own address as source address (addr:00:00:5e:00:01:01, vlan:20)
[ 1519.862993] IPv6: vlan20-v: IPv6 duplicate address fe80::200:5eff:fe00:101 used by 00:00:5e:00:01:01 detected!
[ 1520.181565] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
[ 1520.182739] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
[ 1524.853572] net_ratelimit: 4 callbacks suppressed
[ 1524.854346] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
[ 1525.365565] br1: received packet on vx20 with own address as source address (addr:00:00:5e:00:01:01, vlan:20)
[ 1533.557792] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
[ 1534.069921] br1: received packet on vx20 with own address as source address (addr:00:00:5e:00:01:01, vlan:20)
[ 1550.965225] br1: received packet on vx20 with own address as source address (addr:00:00:5e:00:01:01, vlan:20)
[ 1551.477294] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
[ 1558.064257] device w3 left promiscuous mode
[ 1558.073279] br1: port 4(w3) entered disabled state
[...snip...]
Thanks
Hangbin
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: vxlan_asymmetric.sh test failed every time
2020-10-13 4:39 vxlan_asymmetric.sh test failed every time Hangbin Liu
@ 2020-10-13 7:49 ` Ido Schimmel
2020-10-14 1:39 ` Hangbin Liu
0 siblings, 1 reply; 4+ messages in thread
From: Ido Schimmel @ 2020-10-13 7:49 UTC (permalink / raw)
To: Hangbin Liu; +Cc: Ido Schimmel, Network Development, David Ahern
On Tue, Oct 13, 2020 at 12:39:43PM +0800, Hangbin Liu wrote:
> Hi Ido,
>
> When run vxlan_asymmetric.sh on RHEL8, It failed every time. I though that
> it may failed because the kernel version is too old. But today I tried with
> latest kernel, it still failed. Would you please help check if I missed
> any configuration?
Works OK for me:
$ sudo ./vxlan_asymmetric.sh veth0 veth1 veth2 veth3 veth4 veth5
TEST: ping: local->local vid 10->vid 20 [ OK ]
TEST: ping: local->remote vid 10->vid 10 [ OK ]
TEST: ping: local->remote vid 20->vid 20 [ OK ]
TEST: ping: local->remote vid 10->vid 20 [ OK ]
TEST: ping: local->remote vid 20->vid 10 [ OK ]
INFO: deleting neighbours from vlan interfaces
TEST: ping: local->local vid 10->vid 20 [ OK ]
TEST: ping: local->remote vid 10->vid 10 [ OK ]
TEST: ping: local->remote vid 20->vid 20 [ OK ]
TEST: ping: local->remote vid 10->vid 20 [ OK ]
TEST: ping: local->remote vid 20->vid 10 [ OK ]
TEST: neigh_suppress: on / neigh exists: yes [ OK ]
TEST: neigh_suppress: on / neigh exists: no [ OK ]
TEST: neigh_suppress: off / neigh exists: no [ OK ]
TEST: neigh_suppress: off / neigh exists: yes [ OK ]
# uname -r
5.9.0-rc8-custom-36808-gccdf7fae3afa
# ip -V
ip utility, iproute2-5.8.0
# netsniff-ng -v
netsniff-ng 0.6.7 (Polygon Window), Git id: (none)
The first failure might be related to your rp_filter settings. Can you
please try with this patch?
diff --git a/tools/testing/selftests/net/forwarding/vxlan_asymmetric.sh b/tools/testing/selftests/net/forwarding/vxlan_asymmetric.sh
index a0b5f57d6bd3..0727e2012b68 100755
--- a/tools/testing/selftests/net/forwarding/vxlan_asymmetric.sh
+++ b/tools/testing/selftests/net/forwarding/vxlan_asymmetric.sh
@@ -215,10 +215,16 @@ switch_create()
bridge fdb add 00:00:5e:00:01:01 dev br1 self local vlan 10
bridge fdb add 00:00:5e:00:01:01 dev br1 self local vlan 20
+
+ sysctl_set net.ipv4.conf.all.rp_filter 0
+ sysctl_set net.ipv4.conf.vlan10-v.rp_filter 0
+ sysctl_set net.ipv4.conf.vlan20-v.rp_filter 0
}
switch_destroy()
{
+ sysctl_restore net.ipv4.conf.all.rp_filter
+
bridge fdb del 00:00:5e:00:01:01 dev br1 self local vlan 20
bridge fdb del 00:00:5e:00:01:01 dev br1 self local vlan 10
@@ -359,6 +365,10 @@ ns_switch_create()
bridge fdb add 00:00:5e:00:01:01 dev br1 self local vlan 10
bridge fdb add 00:00:5e:00:01:01 dev br1 self local vlan 20
+
+ sysctl_set net.ipv4.conf.all.rp_filter 0
+ sysctl_set net.ipv4.conf.vlan10-v.rp_filter 0
+ sysctl_set net.ipv4.conf.vlan20-v.rp_filter 0
}
export -f ns_switch_create
>
> # uname -r
> 5.9.0
> # ip -V
> ip utility, iproute2-ss200602
> # netsniff-ng -v
> netsniff-ng 0.6.6 (Syro), Git id: (none)
> # cp forwarding.config.sample forwarding.config
>
> # ./vxlan_asymmetric.sh
> RTNETLINK answers: File exists
> TEST: ping: local->local vid 10->vid 20 [FAIL]
> TEST: ping: local->remote vid 10->vid 10 [ OK ]
> TEST: ping: local->remote vid 20->vid 20 [ OK ]
> TEST: ping: local->remote vid 10->vid 20 [FAIL]
> TEST: ping: local->remote vid 20->vid 10 [FAIL]
> INFO: deleting neighbours from vlan interfaces
> TEST: ping: local->local vid 10->vid 20 [FAIL]
> TEST: ping: local->remote vid 10->vid 10 [ OK ]
> TEST: ping: local->remote vid 20->vid 20 [ OK ]
> TEST: ping: local->remote vid 10->vid 20 [FAIL]
> TEST: ping: local->remote vid 20->vid 10 [FAIL]
> TEST: neigh_suppress: on / neigh exists: yes [ OK ]
> TEST: neigh_suppress: on / neigh exists: no [ OK ]
> TEST: neigh_suppress: off / neigh exists: no [ OK ]
> TEST: neigh_suppress: off / neigh exists: yes [ OK ]
>
> # dmesg
> [...snip...]
> [ 1518.885526] device br1 entered promiscuous mode
> [ 1518.886211] device br1 left promiscuous mode
> [ 1518.890637] device br1 entered promiscuous mode
> [ 1518.941524] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
> [ 1518.949522] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
> [ 1519.165569] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
> [ 1519.166900] IPv6: vlan10-v: IPv6 duplicate address fe80::200:5eff:fe00:101 used by 00:00:5e:00:01:01 detected!
> [ 1519.392633] br1: received packet on vx20 with own address as source address (addr:00:00:5e:00:01:01, vlan:20)
> [ 1519.741559] br1: received packet on vx20 with own address as source address (addr:00:00:5e:00:01:01, vlan:20)
> [ 1519.861641] br1: received packet on vx20 with own address as source address (addr:00:00:5e:00:01:01, vlan:20)
> [ 1519.862993] IPv6: vlan20-v: IPv6 duplicate address fe80::200:5eff:fe00:101 used by 00:00:5e:00:01:01 detected!
> [ 1520.181565] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
> [ 1520.182739] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
> [ 1524.853572] net_ratelimit: 4 callbacks suppressed
> [ 1524.854346] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
> [ 1525.365565] br1: received packet on vx20 with own address as source address (addr:00:00:5e:00:01:01, vlan:20)
> [ 1533.557792] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
> [ 1534.069921] br1: received packet on vx20 with own address as source address (addr:00:00:5e:00:01:01, vlan:20)
> [ 1550.965225] br1: received packet on vx20 with own address as source address (addr:00:00:5e:00:01:01, vlan:20)
> [ 1551.477294] br1: received packet on vx10 with own address as source address (addr:00:00:5e:00:01:01, vlan:10)
> [ 1558.064257] device w3 left promiscuous mode
> [ 1558.073279] br1: port 4(w3) entered disabled state
> [...snip...]
>
> Thanks
> Hangbin
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: vxlan_asymmetric.sh test failed every time
2020-10-13 7:49 ` Ido Schimmel
@ 2020-10-14 1:39 ` Hangbin Liu
2020-10-14 14:45 ` Ido Schimmel
0 siblings, 1 reply; 4+ messages in thread
From: Hangbin Liu @ 2020-10-14 1:39 UTC (permalink / raw)
To: Ido Schimmel; +Cc: Ido Schimmel, Network Development, David Ahern
On Tue, Oct 13, 2020 at 10:49:30AM +0300, Ido Schimmel wrote:
> On Tue, Oct 13, 2020 at 12:39:43PM +0800, Hangbin Liu wrote:
> > Hi Ido,
> >
> > When run vxlan_asymmetric.sh on RHEL8, It failed every time. I though that
> > it may failed because the kernel version is too old. But today I tried with
> > latest kernel, it still failed. Would you please help check if I missed
> > any configuration?
>
> Works OK for me:
>
> $ sudo ./vxlan_asymmetric.sh veth0 veth1 veth2 veth3 veth4 veth5
> TEST: ping: local->local vid 10->vid 20 [ OK ]
> TEST: ping: local->remote vid 10->vid 10 [ OK ]
> TEST: ping: local->remote vid 20->vid 20 [ OK ]
> TEST: ping: local->remote vid 10->vid 20 [ OK ]
> TEST: ping: local->remote vid 20->vid 10 [ OK ]
> INFO: deleting neighbours from vlan interfaces
> TEST: ping: local->local vid 10->vid 20 [ OK ]
> TEST: ping: local->remote vid 10->vid 10 [ OK ]
> TEST: ping: local->remote vid 20->vid 20 [ OK ]
> TEST: ping: local->remote vid 10->vid 20 [ OK ]
> TEST: ping: local->remote vid 20->vid 10 [ OK ]
> TEST: neigh_suppress: on / neigh exists: yes [ OK ]
> TEST: neigh_suppress: on / neigh exists: no [ OK ]
> TEST: neigh_suppress: off / neigh exists: no [ OK ]
> TEST: neigh_suppress: off / neigh exists: yes [ OK ]
>
> # uname -r
> 5.9.0-rc8-custom-36808-gccdf7fae3afa
>
> # ip -V
> ip utility, iproute2-5.8.0
>
> # netsniff-ng -v
> netsniff-ng 0.6.7 (Polygon Window), Git id: (none)
>
> The first failure might be related to your rp_filter settings. Can you
> please try with this patch?
>
> diff --git a/tools/testing/selftests/net/forwarding/vxlan_asymmetric.sh b/tools/testing/selftests/net/forwarding/vxlan_asymmetric.sh
> index a0b5f57d6bd3..0727e2012b68 100755
> --- a/tools/testing/selftests/net/forwarding/vxlan_asymmetric.sh
> +++ b/tools/testing/selftests/net/forwarding/vxlan_asymmetric.sh
> @@ -215,10 +215,16 @@ switch_create()
>
> bridge fdb add 00:00:5e:00:01:01 dev br1 self local vlan 10
> bridge fdb add 00:00:5e:00:01:01 dev br1 self local vlan 20
> +
> + sysctl_set net.ipv4.conf.all.rp_filter 0
> + sysctl_set net.ipv4.conf.vlan10-v.rp_filter 0
> + sysctl_set net.ipv4.conf.vlan20-v.rp_filter 0
> }
>
> switch_destroy()
> {
> + sysctl_restore net.ipv4.conf.all.rp_filter
> +
> bridge fdb del 00:00:5e:00:01:01 dev br1 self local vlan 20
> bridge fdb del 00:00:5e:00:01:01 dev br1 self local vlan 10
>
> @@ -359,6 +365,10 @@ ns_switch_create()
>
> bridge fdb add 00:00:5e:00:01:01 dev br1 self local vlan 10
> bridge fdb add 00:00:5e:00:01:01 dev br1 self local vlan 20
> +
> + sysctl_set net.ipv4.conf.all.rp_filter 0
> + sysctl_set net.ipv4.conf.vlan10-v.rp_filter 0
> + sysctl_set net.ipv4.conf.vlan20-v.rp_filter 0
> }
> export -f ns_switch_create
Thanks a lot for help debugging this issue, this patch works for me.
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2020-10-14 14:45 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2020-10-13 4:39 vxlan_asymmetric.sh test failed every time Hangbin Liu
2020-10-13 7:49 ` Ido Schimmel
2020-10-14 1:39 ` Hangbin Liu
2020-10-14 14:45 ` Ido Schimmel
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).