From: "Marek Behún" <kabel@kernel.org>
To: netdev@vger.kernel.org, Russell King <rmk+kernel@armlinux.org.uk>
Cc: "David S . Miller" <davem@davemloft.net>,
"Florian Fainelli" <f.fainelli@gmail.com>,
"Heiner Kallweit" <hkallweit1@gmail.com>,
kuba@kernel.org, "Marek Behún" <kabel@kernel.org>
Subject: [PATCH net-next v3 16/18] net: phy: marvell10g: differentiate 88E2110 vs 88E2111
Date: Wed, 7 Apr 2021 00:11:05 +0200 [thread overview]
Message-ID: <20210406221107.1004-17-kabel@kernel.org> (raw)
In-Reply-To: <20210406221107.1004-1-kabel@kernel.org>
88E2111 is a variant of 88E2110 which does not support 5 gigabit speeds.
Differentiate these variants via the match_phy_device() method, since
they have the same PHY ID.
Signed-off-by: Marek Behún <kabel@kernel.org>
---
drivers/net/phy/marvell10g.c | 59 ++++++++++++++++++++++++++++++++++++
1 file changed, 59 insertions(+)
diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index 51b7a5083bdf..6269b9041180 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c
@@ -934,6 +934,46 @@ static const struct mv3310_chip mv2110_type = {
#endif
};
+static const struct mv3310_chip mv2111_type = {
+ .supported_interfaces =
+ INITIALIZE_BITMAP(PHY_INTERFACE_MODE_MAX,
+ PHY_INTERFACE_MODE_SGMII,
+ PHY_INTERFACE_MODE_2500BASEX,
+ PHY_INTERFACE_MODE_10GBASER,
+ PHY_INTERFACE_MODE_USXGMII),
+ .get_mactype = mv2110_get_mactype,
+ .init_interface = mv2110_init_interface,
+
+#ifdef CONFIG_HWMON
+ .hwmon_read_temp_reg = mv2110_hwmon_read_temp_reg,
+#endif
+};
+
+static int mv211x_match_phy_device(struct phy_device *phydev, bool has_5g)
+{
+ int val;
+
+ if ((phydev->c45_ids.device_ids[MDIO_MMD_PMAPMD] &
+ MARVELL_PHY_ID_MASK) != MARVELL_PHY_ID_88E2110)
+ return 0;
+
+ val = phy_read_mmd(phydev, MDIO_MMD_PCS, MDIO_SPEED);
+ if (val < 0)
+ return val;
+
+ return !!(val & MDIO_PCS_SPEED_5G) == has_5g;
+}
+
+static int mv2110_match_phy_device(struct phy_device *phydev)
+{
+ return mv211x_match_phy_device(phydev, true);
+}
+
+static int mv2111_match_phy_device(struct phy_device *phydev)
+{
+ return mv211x_match_phy_device(phydev, false);
+}
+
static struct phy_driver mv3310_drivers[] = {
{
.phy_id = MARVELL_PHY_ID_88X3310,
@@ -974,6 +1014,7 @@ static struct phy_driver mv3310_drivers[] = {
{
.phy_id = MARVELL_PHY_ID_88E2110,
.phy_id_mask = MARVELL_PHY_ID_MASK,
+ .match_phy_device = mv2110_match_phy_device,
.name = "mv88e2110",
.driver_data = &mv2110_type,
.probe = mv3310_probe,
@@ -988,6 +1029,24 @@ static struct phy_driver mv3310_drivers[] = {
.remove = mv3310_remove,
.set_loopback = genphy_c45_loopback,
},
+ {
+ .phy_id = MARVELL_PHY_ID_88E2110,
+ .phy_id_mask = MARVELL_PHY_ID_MASK,
+ .match_phy_device = mv2111_match_phy_device,
+ .name = "mv88e2111",
+ .driver_data = &mv2111_type,
+ .probe = mv3310_probe,
+ .suspend = mv3310_suspend,
+ .resume = mv3310_resume,
+ .config_init = mv3310_config_init,
+ .config_aneg = mv3310_config_aneg,
+ .aneg_done = mv3310_aneg_done,
+ .read_status = mv3310_read_status,
+ .get_tunable = mv3310_get_tunable,
+ .set_tunable = mv3310_set_tunable,
+ .remove = mv3310_remove,
+ .set_loopback = genphy_c45_loopback,
+ },
};
module_phy_driver(mv3310_drivers);
--
2.26.2
next prev parent reply other threads:[~2021-04-06 22:12 UTC|newest]
Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-04-06 22:10 [PATCH net-next v3 00/18] net: phy: marvell10g updates Marek Behún
2021-04-06 22:10 ` [PATCH net-next v3 01/18] net: phy: marvell10g: rename register Marek Behún
2021-04-06 22:37 ` Andrew Lunn
2021-04-06 22:10 ` [PATCH net-next v3 02/18] net: phy: marvell10g: fix typo Marek Behún
2021-04-06 22:38 ` Andrew Lunn
2021-04-06 22:10 ` [PATCH net-next v3 03/18] net: phy: marvell10g: allow 5gbase-r and usxgmii Marek Behún
2021-04-06 22:39 ` Andrew Lunn
2021-04-06 22:10 ` [PATCH net-next v3 04/18] net: phy: marvell10g: indicate 88X33x0 only port control registers Marek Behún
2021-04-07 0:10 ` Andrew Lunn
2021-04-07 0:22 ` Marek Behún
2021-04-06 22:10 ` [PATCH net-next v3 05/18] net: phy: marvell10g: add all MACTYPE definitions for 88X33x0 Marek Behún
2021-04-06 23:22 ` Andrew Lunn
2021-04-06 22:10 ` [PATCH net-next v3 06/18] net: phy: marvell10g: add MACTYPE definitions for 88E21xx Marek Behún
2021-04-06 23:22 ` Andrew Lunn
2021-04-06 22:10 ` [PATCH net-next v3 07/18] net: phy: marvell10g: support all rate matching modes Marek Behún
2021-04-06 23:30 ` Andrew Lunn
2021-04-06 23:36 ` Marek Behún
2021-04-06 23:33 ` Andrew Lunn
2021-04-06 23:53 ` Marek Behún
2021-04-06 22:10 ` [PATCH net-next v3 08/18] include: add library helpers for variadic macro expansion Marek Behún
2021-04-06 22:10 ` [PATCH net-next v3 09/18] include: bitmap: add macro for bitmap initialization Marek Behún
2021-04-06 23:38 ` Andrew Lunn
2021-04-06 23:50 ` Marek Behún
2021-04-06 22:10 ` [PATCH net-next v3 10/18] net: phy: marvell10g: check for correct supported interface mode Marek Behún
2021-04-06 23:40 ` Andrew Lunn
2021-04-06 22:11 ` [PATCH net-next v3 11/18] net: phy: marvell10g: store temperature read method in chip strucutre Marek Behún
2021-04-06 23:42 ` Andrew Lunn
2021-04-06 22:11 ` [PATCH net-next v3 12/18] net: phy: marvell10g: support other MACTYPEs Marek Behún
2021-04-06 22:11 ` [PATCH net-next v3 13/18] net: phy: marvell10g: add separate structure for 88X3340 Marek Behún
2021-04-06 23:47 ` Andrew Lunn
2021-04-06 22:11 ` [PATCH net-next v3 14/18] net: phy: marvell10g: fix driver name for mv88e2110 Marek Behún
2021-04-06 23:49 ` Andrew Lunn
2021-04-06 22:11 ` [PATCH net-next v3 15/18] net: phy: add constants for 2.5G and 5G speed in PCS speed register Marek Behún
2021-04-06 23:59 ` Andrew Lunn
2021-04-06 22:11 ` Marek Behún [this message]
2021-04-07 0:01 ` [PATCH net-next v3 16/18] net: phy: marvell10g: differentiate 88E2110 vs 88E2111 Andrew Lunn
2021-04-06 22:11 ` [PATCH net-next v3 17/18] net: phy: marvell10g: change module description Marek Behún
2021-04-07 0:01 ` Andrew Lunn
2021-04-06 22:11 ` [PATCH net-next v3 18/18] MAINTAINERS: add myself as maintainer of marvell10g driver Marek Behún
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210406221107.1004-17-kabel@kernel.org \
--to=kabel@kernel.org \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=hkallweit1@gmail.com \
--cc=kuba@kernel.org \
--cc=netdev@vger.kernel.org \
--cc=rmk+kernel@armlinux.org.uk \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).