[PATCH net-next v3 04/18] net: phy: marvell10g: indicate 88X33x0 only port control registers

["Marek Behún" <kabel@kernel.org>]

Rename port control registers to indicate that they are valid only for
88X33x0, not for 88E21x0.

Signed-off-by: Marek Behún <kabel@kernel.org>
---
 drivers/net/phy/marvell10g.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/drivers/net/phy/marvell10g.c b/drivers/net/phy/marvell10g.c
index 881a0717846e..7552a658a513 100644
--- a/drivers/net/phy/marvell10g.c
+++ b/drivers/net/phy/marvell10g.c
@@ -78,10 +78,10 @@ enum {
 
 	/* Vendor2 MMD registers */
 	MV_V2_PORT_CTRL		= 0xf001,
-	MV_V2_PORT_CTRL_SWRST	= BIT(15),
-	MV_V2_PORT_CTRL_PWRDOWN	= BIT(11),
-	MV_V2_PORT_CTRL_MACTYPE_MASK = 0x7,
-	MV_V2_PORT_CTRL_MACTYPE_RATE_MATCH = 0x6,
+	MV_V2_PORT_CTRL_PWRDOWN			= BIT(11),
+	MV_V2_33X0_PORT_CTRL_SWRST		= BIT(15),
+	MV_V2_33X0_PORT_CTRL_MACTYPE_MASK	= 0x7,
+	MV_V2_33X0_PORT_CTRL_MACTYPE_RATE_MATCH	= 0x6,
 	/* Temperature control/read registers (88X3310 only) */
 	MV_V2_TEMP_CTRL		= 0xf08a,
 	MV_V2_TEMP_CTRL_MASK	= 0xc000,
@@ -268,7 +268,7 @@ static int mv3310_power_up(struct phy_device *phydev)
 		return ret;
 
 	return phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL,
-				MV_V2_PORT_CTRL_SWRST);
+				MV_V2_33X0_PORT_CTRL_SWRST);
 }
 
 static int mv3310_reset(struct phy_device *phydev, u32 unit)
@@ -479,8 +479,8 @@ static int mv3310_config_init(struct phy_device *phydev)
 	val = phy_read_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL);
 	if (val < 0)
 		return val;
-	priv->rate_match = ((val & MV_V2_PORT_CTRL_MACTYPE_MASK) ==
-			MV_V2_PORT_CTRL_MACTYPE_RATE_MATCH);
+	priv->rate_match = ((val & MV_V2_33X0_PORT_CTRL_MACTYPE_MASK) ==
+			MV_V2_33X0_PORT_CTRL_MACTYPE_RATE_MATCH);
 
 	/* Enable EDPD mode - saving 600mW */
 	return mv3310_set_edpd(phydev, ETHTOOL_PHY_EDPD_DFLT_TX_MSECS);
-- 
2.26.2