Re: [PATCH net-next v3 2/9] net: dsa: microchip: ksz8795: add phylink support

[Vladimir Oltean <olteanv@gmail.com>]

On Wed, May 26, 2021 at 06:30:30AM +0200, Oleksij Rempel wrote:
> From: Michael Grzeschik <m.grzeschik@pengutronix.de>
> 
> This patch adds the phylink support to the ksz8795 driver to provide
> configuration exceptions on quirky KSZ8863 and KSZ8873 ports.
> 
> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  drivers/net/dsa/microchip/ksz8795.c | 59 +++++++++++++++++++++++++++++
>  1 file changed, 59 insertions(+)
> 
> diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
> index ba065003623f..cf81ae87544d 100644
> --- a/drivers/net/dsa/microchip/ksz8795.c
> +++ b/drivers/net/dsa/microchip/ksz8795.c
> @@ -18,6 +18,7 @@
>  #include <linux/micrel_phy.h>
>  #include <net/dsa.h>
>  #include <net/switchdev.h>
> +#include <linux/phylink.h>
>  
>  #include "ksz_common.h"
>  #include "ksz8795_reg.h"
> @@ -1420,11 +1421,69 @@ static int ksz8_setup(struct dsa_switch *ds)
>  	return 0;
>  }
>  
> +static void ksz8_validate(struct dsa_switch *ds, int port,
> +			  unsigned long *supported,
> +			  struct phylink_link_state *state)
> +{
> +	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
> +	struct ksz_device *dev = ds->priv;
> +
> +	if (port == dev->cpu_port) {
> +		if (state->interface != PHY_INTERFACE_MODE_RMII &&
> +		    state->interface != PHY_INTERFACE_MODE_MII &&
> +		    state->interface != PHY_INTERFACE_MODE_NA)
> +			goto unsupported;
> +	} else if (port > dev->port_cnt) {
> +		bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
> +		dev_err(ds->dev, "Unsupported port: %i\n", port);
> +		return;

Is this possible or do we just like to invent things to check?
Unless I'm missing something, ksz8_switch_init() does:

	dev->ds->num_ports = dev->port_cnt;

and dsa_port_phylink_validate() does:

	ds->ops->phylink_validate(ds, dp->index, supported, state);

where dp->index is set to @port by dsa_port_touch() in this loop:

	for (port = 0; port < ds->num_ports; port++) {
		dp = dsa_port_touch(ds, port);
		if (!dp)
			return -ENOMEM;
	}

So, if 0 <= dp->index < ds->num_ports == dev->port_cnt, what is the point?

> +	} else {
> +		if (state->interface != PHY_INTERFACE_MODE_INTERNAL &&
> +		    state->interface != PHY_INTERFACE_MODE_NA)
> +			goto unsupported;
> +	}
> +
> +	/* Allow all the expected bits */
> +	phylink_set_port_modes(mask);
> +	phylink_set(mask, Autoneg);
> +
> +	/* Silicon Errata Sheet (DS80000830A):
> +	 * "Port 1 does not respond to received flow control PAUSE frames"
> +	 * So, disable Pause support on "Port 1" (port == 0) for all ksz88x3
> +	 * switches.
> +	 */
> +	if (!ksz_is_ksz88x3(dev) || port)
> +		phylink_set(mask, Pause);
> +
> +	/* Asym pause is not supported on KSZ8863 and KSZ8873 */
> +	if (!ksz_is_ksz88x3(dev))
> +		phylink_set(mask, Asym_Pause);
> +
> +	/* 10M and 100M are only supported */
> +	phylink_set(mask, 10baseT_Half);
> +	phylink_set(mask, 10baseT_Full);
> +	phylink_set(mask, 100baseT_Half);
> +	phylink_set(mask, 100baseT_Full);
> +
> +	bitmap_and(supported, supported, mask,
> +		   __ETHTOOL_LINK_MODE_MASK_NBITS);
> +	bitmap_and(state->advertising, state->advertising, mask,
> +		   __ETHTOOL_LINK_MODE_MASK_NBITS);
> +
> +	return;
> +
> +unsupported:
> +	bitmap_zero(supported, __ETHTOOL_LINK_MODE_MASK_NBITS);
> +	dev_err(ds->dev, "Unsupported interface: %s, port: %d\n",
> +		phy_modes(state->interface), port);
> +}
> +
>  static const struct dsa_switch_ops ksz8_switch_ops = {
>  	.get_tag_protocol	= ksz8_get_tag_protocol,
>  	.setup			= ksz8_setup,
>  	.phy_read		= ksz_phy_read16,
>  	.phy_write		= ksz_phy_write16,
> +	.phylink_validate	= ksz8_validate,
>  	.phylink_mac_link_down	= ksz_mac_link_down,
>  	.port_enable		= ksz_enable_port,
>  	.get_strings		= ksz8_get_strings,
> -- 
> 2.29.2
>