netdev.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Oleksij Rempel <o.rempel@pengutronix.de>
To: Woojung Huh <woojung.huh@microchip.com>,
	UNGLinuxDriver@microchip.com, Andrew Lunn <andrew@lunn.ch>,
	Florian Fainelli <f.fainelli@gmail.com>,
	Vivien Didelot <vivien.didelot@gmail.com>,
	Vladimir Oltean <olteanv@gmail.com>,
	"David S. Miller" <davem@davemloft.net>,
	Jakub Kicinski <kuba@kernel.org>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>,
	kernel@pengutronix.de, netdev@vger.kernel.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH net-next v2 1/1] net: dsa: microchip: ksz9477: implement MTU configuration
Date: Wed, 23 Feb 2022 09:40:55 +0100	[thread overview]
Message-ID: <20220223084055.2719969-1-o.rempel@pengutronix.de> (raw)

This chips supports two ways to configure max MTU size:
- by setting SW_LEGAL_PACKET_DISABLE bit: if this bit is 0 allowed packed size
  will be between 64 and bytes 1518. If this bit is 1, it will accept
  packets up to 2000 bytes.
- by setting SW_JUMBO_PACKET bit. If this bit is set, the chip will
  ignore SW_LEGAL_PACKET_DISABLE value and use REG_SW_MTU__2 register to
  configure MTU size.

Current driver has disabled SW_JUMBO_PACKET bit and activates
SW_LEGAL_PACKET_DISABLE. So the switch will pass all packets up to 2000 without
any way to configure it.

By providing port_change_mtu we are switch to SW_JUMBO_PACKET way and will
be able to configure MTU up to ~9000.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
changes v2:
- rename max_mtu to max_frame and new_mtu to frame_size
- use max() instead of if(>)
---
 drivers/net/dsa/microchip/ksz9477.c     | 40 +++++++++++++++++++++++--
 drivers/net/dsa/microchip/ksz9477_reg.h |  4 +++
 drivers/net/dsa/microchip/ksz_common.h  |  1 +
 3 files changed, 43 insertions(+), 2 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz9477.c b/drivers/net/dsa/microchip/ksz9477.c
index 18ffc8ded7ee..5c5f78cb970e 100644
--- a/drivers/net/dsa/microchip/ksz9477.c
+++ b/drivers/net/dsa/microchip/ksz9477.c
@@ -11,6 +11,7 @@
 #include <linux/platform_data/microchip-ksz.h>
 #include <linux/phy.h>
 #include <linux/if_bridge.h>
+#include <linux/if_vlan.h>
 #include <net/dsa.h>
 #include <net/switchdev.h>
 
@@ -182,6 +183,33 @@ static void ksz9477_port_cfg32(struct ksz_device *dev, int port, int offset,
 			   bits, set ? bits : 0);
 }
 
+static int ksz9477_change_mtu(struct dsa_switch *ds, int port, int mtu)
+{
+	struct ksz_device *dev = ds->priv;
+	u16 frame_size, max_frame = 0;
+	int i;
+
+	frame_size = mtu + ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN;
+
+	if (dsa_is_cpu_port(ds, port))
+		frame_size += KSZ9477_INGRESS_TAG_LEN;
+
+	/* Cache the per-port MTU setting */
+	dev->ports[port].max_frame = frame_size;
+
+	for (i = 0; i < dev->port_cnt; i++)
+		max_frame = max(max_frame, dev->ports[i].max_frame);
+
+	return regmap_update_bits(dev->regmap[1], REG_SW_MTU__2,
+				  REG_SW_MTU_MASK, max_frame);
+}
+
+static int ksz9477_max_mtu(struct dsa_switch *ds, int port)
+{
+	return KSZ9477_MAX_FRAME_SIZE - ETH_HLEN - ETH_FCS_LEN - VLAN_HLEN -
+		KSZ9477_INGRESS_TAG_LEN;
+}
+
 static int ksz9477_wait_vlan_ctrl_ready(struct ksz_device *dev)
 {
 	unsigned int val;
@@ -1412,8 +1440,14 @@ static int ksz9477_setup(struct dsa_switch *ds)
 	/* Do not work correctly with tail tagging. */
 	ksz_cfg(dev, REG_SW_MAC_CTRL_0, SW_CHECK_LENGTH, false);
 
-	/* accept packet up to 2000bytes */
-	ksz_cfg(dev, REG_SW_MAC_CTRL_1, SW_LEGAL_PACKET_DISABLE, true);
+	/* Enable REG_SW_MTU__2 reg by setting SW_JUMBO_PACKET */
+	ksz_cfg(dev, REG_SW_MAC_CTRL_1, SW_JUMBO_PACKET, true);
+
+	/* Now we can configure default MTU value */
+	ret = regmap_update_bits(dev->regmap[1], REG_SW_MTU__2, REG_SW_MTU_MASK,
+				 VLAN_ETH_FRAME_LEN + ETH_FCS_LEN);
+	if (ret)
+		return ret;
 
 	ksz9477_config_cpu_port(ds);
 
@@ -1460,6 +1494,8 @@ static const struct dsa_switch_ops ksz9477_switch_ops = {
 	.port_mirror_add	= ksz9477_port_mirror_add,
 	.port_mirror_del	= ksz9477_port_mirror_del,
 	.get_stats64		= ksz9477_get_stats64,
+	.port_change_mtu	= ksz9477_change_mtu,
+	.port_max_mtu		= ksz9477_max_mtu,
 };
 
 static u32 ksz9477_get_port_addr(int port, int offset)
diff --git a/drivers/net/dsa/microchip/ksz9477_reg.h b/drivers/net/dsa/microchip/ksz9477_reg.h
index 16939f29faa5..2278e763ee3e 100644
--- a/drivers/net/dsa/microchip/ksz9477_reg.h
+++ b/drivers/net/dsa/microchip/ksz9477_reg.h
@@ -176,6 +176,7 @@
 #define REG_SW_MAC_ADDR_5		0x0307
 
 #define REG_SW_MTU__2			0x0308
+#define REG_SW_MTU_MASK			GENMASK(13, 0)
 
 #define REG_SW_ISP_TPID__2		0x030A
 
@@ -1662,4 +1663,7 @@
 /* 148,800 frames * 67 ms / 100 */
 #define BROADCAST_STORM_VALUE		9969
 
+#define KSZ9477_INGRESS_TAG_LEN		2
+#define KSZ9477_MAX_FRAME_SIZE		9000
+
 #endif /* KSZ9477_REGS_H */
diff --git a/drivers/net/dsa/microchip/ksz_common.h b/drivers/net/dsa/microchip/ksz_common.h
index c6fa487fb006..739365bfceb2 100644
--- a/drivers/net/dsa/microchip/ksz_common.h
+++ b/drivers/net/dsa/microchip/ksz_common.h
@@ -41,6 +41,7 @@ struct ksz_port {
 
 	struct ksz_port_mib mib;
 	phy_interface_t interface;
+	u16 max_frame;
 };
 
 struct ksz_device {
-- 
2.30.2


             reply	other threads:[~2022-02-23  8:41 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-02-23  8:40 Oleksij Rempel [this message]
2022-02-23 23:38 ` [PATCH net-next v2 1/1] net: dsa: microchip: ksz9477: implement MTU configuration Vladimir Oltean
2022-02-24  4:59   ` Oleksij Rempel
2022-02-24  9:33     ` Vladimir Oltean
2022-02-24  9:38       ` Oleksij Rempel
2022-02-24  9:46         ` Vladimir Oltean
2022-02-25 11:47           ` Oleksij Rempel
2022-02-25 11:58             ` Vladimir Oltean
2022-02-25 12:54               ` Oleksij Rempel
2022-02-25 16:35                 ` Vladimir Oltean
2022-03-08 10:06                   ` Oleksij Rempel
2022-03-08 11:21                     ` Vladimir Oltean
2022-03-08 11:59                       ` Oleksij Rempel

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220223084055.2719969-1-o.rempel@pengutronix.de \
    --to=o.rempel@pengutronix.de \
    --cc=UNGLinuxDriver@microchip.com \
    --cc=andrew@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=f.fainelli@gmail.com \
    --cc=kernel@pengutronix.de \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=olteanv@gmail.com \
    --cc=vivien.didelot@gmail.com \
    --cc=woojung.huh@microchip.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).