netdev.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: David Yang <mmyangfl@gmail.com>
To: mmyangfl@gmail.com
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>,
	"David S. Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@google.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	netdev@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH v6] net: mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
Date: Sun,  2 Oct 2022 01:45:23 +0800	[thread overview]
Message-ID: <20221001174524.2007912-1-mmyangfl@gmail.com> (raw)
In-Reply-To: <202210020108.UlXaYP3c-lkp@intel.com>

Support mode switch properly, which is not available before.

If SoC has two Ethernet controllers, by setting both of them into MII
mode, the first controller enters GMII mode, while the second
controller is effectively disabled. This requires configuring (and
maybe enabling) the second controller in the device tree, even though
it cannot be used.

Signed-off-by: David Yang <mmyangfl@gmail.com>
---
v2: clarify modes work on controllers, read default value from PSC1
v3: Kirkwood only
v4: cleanup
v5: test on 88f6282
v6: fix missing header reported by kernel test robot
 drivers/net/ethernet/marvell/mv643xx_eth.c | 49 ++++++++++++++++++----
 include/linux/mv643xx_eth.h                |  2 +
 2 files changed, 44 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mv643xx_eth.c b/drivers/net/ethernet/marvell/mv643xx_eth.c
index b6be0552a..ed674c512 100644
--- a/drivers/net/ethernet/marvell/mv643xx_eth.c
+++ b/drivers/net/ethernet/marvell/mv643xx_eth.c
@@ -108,6 +108,7 @@ static char mv643xx_eth_driver_version[] = "1.4";
 #define TXQ_COMMAND			0x0048
 #define TXQ_FIX_PRIO_CONF		0x004c
 #define PORT_SERIAL_CONTROL1		0x004c
+#define  RGMII_EN			0x00000008
 #define  CLK125_BYPASS_EN		0x00000010
 #define TX_BW_RATE			0x0050
 #define TX_BW_MTU			0x0058
@@ -2761,6 +2762,8 @@ static int mv643xx_eth_shared_of_add_port(struct platform_device *pdev,
 	mv643xx_eth_property(pnp, "rx-sram-addr", ppd.rx_sram_addr);
 	mv643xx_eth_property(pnp, "rx-sram-size", ppd.rx_sram_size);
 
+	of_get_phy_mode(pnp, &ppd.interface);
+
 	ppd.phy_node = of_parse_phandle(pnp, "phy-handle", 0);
 	if (!ppd.phy_node) {
 		ppd.phy_addr = MV643XX_ETH_PHY_NONE;
@@ -3092,6 +3095,7 @@ static int mv643xx_eth_probe(struct platform_device *pdev)
 	struct mv643xx_eth_private *mp;
 	struct net_device *dev;
 	struct phy_device *phydev = NULL;
+	u32 psc1r;
 	int err, irq;
 
 	pd = dev_get_platdata(&pdev->dev);
@@ -3119,14 +3123,45 @@ static int mv643xx_eth_probe(struct platform_device *pdev)
 
 	mp->dev = dev;
 
-	/* Kirkwood resets some registers on gated clocks. Especially
-	 * CLK125_BYPASS_EN must be cleared but is not available on
-	 * all other SoCs/System Controllers using this driver.
-	 */
 	if (of_device_is_compatible(pdev->dev.of_node,
-				    "marvell,kirkwood-eth-port"))
-		wrlp(mp, PORT_SERIAL_CONTROL1,
-		     rdlp(mp, PORT_SERIAL_CONTROL1) & ~CLK125_BYPASS_EN);
+				    "marvell,kirkwood-eth-port")) {
+		psc1r = rdlp(mp, PORT_SERIAL_CONTROL1);
+
+		/* Kirkwood resets some registers on gated clocks. Especially
+		 * CLK125_BYPASS_EN must be cleared but is not available on
+		 * all other SoCs/System Controllers using this driver.
+		 */
+		psc1r &= ~CLK125_BYPASS_EN;
+
+		/* On Kirkwood with two Ethernet controllers, if both of them
+		 * have RGMII_EN disabled, the first controller will be in GMII
+		 * mode and the second one is effectively disabled, instead of
+		 * two MII interfaces.
+		 *
+		 * To enable GMII in the first controller, the second one must
+		 * also be configured (and may be enabled) with RGMII_EN
+		 * disabled too, even though it cannot be used at all.
+		 */
+		switch (pd->interface) {
+		/* Use internal to denote second controller being disabled */
+		case PHY_INTERFACE_MODE_INTERNAL:
+		case PHY_INTERFACE_MODE_MII:
+		case PHY_INTERFACE_MODE_GMII:
+			psc1r &= ~RGMII_EN;
+			break;
+		case PHY_INTERFACE_MODE_RGMII:
+		case PHY_INTERFACE_MODE_RGMII_ID:
+		case PHY_INTERFACE_MODE_RGMII_RXID:
+		case PHY_INTERFACE_MODE_RGMII_TXID:
+			psc1r |= RGMII_EN;
+			break;
+		default:
+			/* Unknown; don't touch */
+			break;
+		}
+
+		wrlp(mp, PORT_SERIAL_CONTROL1, psc1r);
+	}
 
 	/*
 	 * Start with a default rate, and if there is a clock, allow
diff --git a/include/linux/mv643xx_eth.h b/include/linux/mv643xx_eth.h
index 3682ae75c..145169be2 100644
--- a/include/linux/mv643xx_eth.h
+++ b/include/linux/mv643xx_eth.h
@@ -8,6 +8,7 @@
 
 #include <linux/mbus.h>
 #include <linux/if_ether.h>
+#include <linux/phy.h>
 
 #define MV643XX_ETH_SHARED_NAME		"mv643xx_eth"
 #define MV643XX_ETH_NAME		"mv643xx_eth_port"
@@ -59,6 +60,7 @@ struct mv643xx_eth_platform_data {
 	 */
 	int			speed;
 	int			duplex;
+	phy_interface_t		interface;
 
 	/*
 	 * How many RX/TX queues to use.
-- 
2.35.1


       reply	other threads:[~2022-10-01 17:45 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <202210020108.UlXaYP3c-lkp@intel.com>
2022-10-01 17:45 ` David Yang [this message]
2022-10-04  0:13   ` [PATCH v6] net: mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood Jakub Kicinski
2022-10-04 14:36     ` Jakub Kicinski
2022-10-28  2:01       ` David Yang
2022-11-07  8:50         ` patchwork-bot+netdevbpf

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20221001174524.2007912-1-mmyangfl@gmail.com \
    --to=mmyangfl@gmail.com \
    --cc=davem@davemloft.net \
    --cc=edumazet@google.com \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=pabeni@redhat.com \
    --cc=sebastian.hesselbarth@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).