Re: [PATCH v2 1/3] dsa: marvell: Provide per device information about max frame size

[Lukasz Majewski <lukma@denx.de>]

[-- Attachment #1: Type: text/plain, Size: 4804 bytes --]

Hi Alexander,

> Hi Alexander,
> 
> > On Fri, Dec 16, 2022 at 5:05 AM Lukasz Majewski <lukma@denx.de>
> > wrote:  
> > >
> > > Hi Alexander,
> > >    
> > > > On Thu, 2022-12-15 at 15:45 +0100, Lukasz Majewski wrote:    
> > > > > Different Marvell DSA switches support different size of max
> > > > > frame bytes to be sent.
> > > > >
> > > > > For example mv88e6185 supports max 1632 bytes, which is now
> > > > > in-driver standard value. On the other hand - mv88e6250
> > > > > supports 2048 bytes.
> > > > >
> > > > > As this value is internal and may be different for each switch
> > > > > IC, new entry in struct mv88e6xxx_info has been added to store
> > > > > it.
> > > > >
> > > > > Signed-off-by: Lukasz Majewski <lukma@denx.de>
> > > > > ---
> > > > > Changes for v2:
> > > > > - Define max_frame_size with default value of 1632 bytes,
> > > > > - Set proper value for the mv88e6250 switch SoC (linkstreet)
> > > > > family ---
> > > > >  drivers/net/dsa/mv88e6xxx/chip.c | 13 ++++++++++++-
> > > > >  drivers/net/dsa/mv88e6xxx/chip.h |  1 +
> > > > >  2 files changed, 13 insertions(+), 1 deletion(-)
> > > > >
> > > > > diff --git a/drivers/net/dsa/mv88e6xxx/chip.c
> > > > > b/drivers/net/dsa/mv88e6xxx/chip.c index
> > > > > 2ca3cbba5764..7ae4c389ce50 100644 ---
> > > > > a/drivers/net/dsa/mv88e6xxx/chip.c +++
> > > > > b/drivers/net/dsa/mv88e6xxx/chip.c @@ -3093,7 +3093,9 @@
> > > > > static int mv88e6xxx_get_max_mtu(struct dsa_switch *ds, int
> > > > > port) if (chip->info->ops->port_set_jumbo_size) return 10240 -
> > > > > VLAN_ETH_HLEN - EDSA_HLEN - ETH_FCS_LEN; else if
> > > > > (chip->info->ops->set_max_frame_size)
> > > > > -           return 1632 - VLAN_ETH_HLEN - EDSA_HLEN -
> > > > > ETH_FCS_LEN;
> > > > > +           return (chip->info->max_frame_size  -
> > > > > VLAN_ETH_HLEN
> > > > > +                   - EDSA_HLEN - ETH_FCS_LEN);
> > > > > +
> > > > >     return 1522 - VLAN_ETH_HLEN - EDSA_HLEN - ETH_FCS_LEN;
> > > > >  }
> > > > >
> > > > >    
> > > >
> > > > Is there any specific reason for triggering this based on the
> > > > existance of the function call?    
> > >
> > > This was the original code in this driver.
> > >
> > > This value (1632 or 2048 bytes) is SoC (family) specific.
> > >
> > > By checking which device defines set_max_frame_size callback, I
> > > could fill the chip->info->max_frame_size with 1632 value.
> > >    
> > > > Why not just replace:
> > > >       else if (chip->info->ops->set_max_frame_size)
> > > > with:
> > > >       else if (chip->info->max_frame_size)
> > > >    
> > >
> > > I think that the callback check is a bit "defensive" approach ->
> > > 1522B is the default value and 1632 (or 10240 - jumbo) can be set
> > > only when proper callback is defined.
> > >    
> > > > Otherwise my concern is one gets defined without the other
> > > > leading to a future issue as 0 - extra headers will likely wrap
> > > > and while the return value may be a signed int, it is usually
> > > > stored in an unsigned int so it would effectively uncap the
> > > > MTU.    
> > >
> > > Please correct me if I misunderstood something:
> > >
> > > The problem is with new mv88eXXXX devices, which will not provide
> > > max_frame_size information to their chip->info struct?
> > >
> > > Or is there any other issue?    
> > 
> > That was mostly my concern. I was adding a bit of my own defensive
> > programming in the event that somebody forgot to fill out the
> > chip->info. If nothing else it might make sense to add a check to
> > verify that the max_frame_size is populated before blindly using it.
> > So perhaps you could do something similar to the max_t approach I
> > had called out earlier but instead of applying it on the last case
> > you could apply it for the "set_max_frame_size" case with 1632
> > being the minimum and being overwritten by 2048 if it is set in
> > max_frame_size.  
> 
> I think that I shall add:
> 
> else if (chip->info->ops->set_max_frame_size)
> 	return max_t(int, chip->info->max_frame_size, 1632) -
> (headers)
> 
> So then the "default" value of 1632 will be overwritten by 2048 bytes.
> 

Is this approach acceptable for you?

> 
> Best regards,
> 
> Lukasz Majewski
> 
> --
> 
> DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
> lukma@denx.de




Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@denx.de

[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 488 bytes --]