[PATCH net-next v7 0/9] net: add EEE support for KSZ9477 and AR8035 with i.MX6

[PATCH net-next v7 0/9] net: add EEE support for KSZ9477 and AR8035 with i.MX6

[Oleksij Rempel]

changes v7:
- update documentation for genphy_c45_eee_is_active()
- address review comments on "net: dsa: microchip: enable EEE support"
  patch

changes v6:
- split patch set and send only first 9 patches
- Add Reviewed-by: Andrew Lunn <andrew@lunn.ch>
- use 0xffff instead of GENMASK
- Document @supported_eee
- use "()" with function name in comments

changes v5:
- spell fixes
- move part of genphy_c45_read_eee_abilities() to
  genphy_c45_read_eee_cap1()
- validate MDIO_PCS_EEE_ABLE register against 0xffff val.
- rename *eee_100_10000* to *eee_cap1*
- use linkmode_intersects(phydev->supported, PHY_EEE_CAP1_FEATURES)
  instead of !linkmode_empty()
- add documentation to linkmode/register helpers

changes v4:
- remove following helpers:
  mmd_eee_cap_to_ethtool_sup_t
  mmd_eee_adv_to_ethtool_adv_t
  ethtool_adv_to_mmd_eee_adv_t
  and port drivers from this helpers to linkmode helpers.
- rebase against latest net-next
- port phy_init_eee() to genphy_c45_eee_is_active()

changes v3:
- rework some parts of EEE infrastructure and move it to c45 code.
- add supported_eee storage and start using it in EEE code and by the
  micrel driver.
- add EEE support for ar8035 PHY
- add SmartEEE support to FEC i.MX series.

changes v2:
- use phydev->supported instead of reading MII_BMSR regiaster
- fix @get_eee > @set_eee

With this patch series we provide EEE control for KSZ9477 family of switches and
AR8035 with i.MX6 configuration.
According to my tests, on a system with KSZ8563 switch and 100Mbit idle link,
we consume 0,192W less power per port if EEE is enabled.

Oleksij Rempel (9):
  net: dsa: microchip: enable EEE support
  net: phy: add genphy_c45_read_eee_abilities() function
  net: phy: micrel: add ksz9477_get_features()
  net: phy: export phy_check_valid() function
  net: phy: add genphy_c45_ethtool_get/set_eee() support
  net: phy: c22: migrate to genphy_c45_write_eee_adv()
  net: phy: c45: migrate to genphy_c45_write_eee_adv()
  net: phy: migrate phy_init_eee() to genphy_c45_eee_is_active()
  net: phy: start using genphy_c45_ethtool_get/set_eee()

 drivers/net/dsa/microchip/ksz_common.c |  66 +++++
 drivers/net/phy/micrel.c               |  21 ++
 drivers/net/phy/phy-c45.c              | 319 ++++++++++++++++++++++++-
 drivers/net/phy/phy.c                  | 153 ++----------
 drivers/net/phy/phy_device.c           |  26 +-
 include/linux/mdio.h                   |  84 +++++++
 include/linux/phy.h                    |  14 ++
 include/uapi/linux/mdio.h              |   8 +
 8 files changed, 554 insertions(+), 137 deletions(-)

-- 
2.30.2

[PATCH net-next v7 1/9] net: dsa: microchip: enable EEE support

[Oleksij Rempel]

Some of KSZ9477 family switches provides EEE support. To enable it, we
just need to register set_mac_eee/set_mac_eee handlers and validate
supported chip version and port.

Currently supported chip variants are: KSZ8563, KSZ9477, KSZ9563,
KSZ9567, KSZ9893, KSZ9896, KSZ9897. KSZ8563 supports EEE only with
100BaseTX/Full.  Other chips support 100BaseTX/Full and 1000BaseTX/Full.
Low Power Idle configuration is not supported and currently not
documented in the datasheets.

EEE PHY specific tunings are not documented in the switch datasheets, but can
overlap with KSZ9131 specification.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/dsa/microchip/ksz_common.c | 66 ++++++++++++++++++++++++++
 1 file changed, 66 insertions(+)

diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c
index 46becc0382d6..729b36eeb2c4 100644
--- a/drivers/net/dsa/microchip/ksz_common.c
+++ b/drivers/net/dsa/microchip/ksz_common.c
@@ -2673,6 +2673,70 @@ static int ksz_max_mtu(struct dsa_switch *ds, int port)
 	return -EOPNOTSUPP;
 }
 
+static int ksz_validate_eee(struct dsa_switch *ds, int port)
+{
+	struct ksz_device *dev = ds->priv;
+
+	if (!dev->info->internal_phy[port])
+		return -EOPNOTSUPP;
+
+	switch (dev->chip_id) {
+	case KSZ8563_CHIP_ID:
+	case KSZ9477_CHIP_ID:
+	case KSZ9563_CHIP_ID:
+	case KSZ9567_CHIP_ID:
+	case KSZ9893_CHIP_ID:
+	case KSZ9896_CHIP_ID:
+	case KSZ9897_CHIP_ID:
+		return 0;
+	}
+
+	return -EOPNOTSUPP;
+}
+
+static int ksz_get_mac_eee(struct dsa_switch *ds, int port,
+			   struct ethtool_eee *e)
+{
+	int ret;
+
+	ret = ksz_validate_eee(ds, port);
+	if (ret)
+		return ret;
+
+	/* There is no documented control of Tx LPI configuration. */
+	e->tx_lpi_enabled = true;
+
+	/* There is no documented control of Tx LPI timer. According to tests
+	 * Tx LPI timer seems to be set by default to minimal value.
+	 */
+	e->tx_lpi_timer = 0;
+
+	return 0;
+}
+
+static int ksz_set_mac_eee(struct dsa_switch *ds, int port,
+			   struct ethtool_eee *e)
+{
+	struct ksz_device *dev = ds->priv;
+	int ret;
+
+	ret = ksz_validate_eee(ds, port);
+	if (ret)
+		return ret;
+
+	if (!e->tx_lpi_enabled) {
+		dev_err(dev->dev, "Disabling EEE Tx LPI is not supported\n");
+		return -EINVAL;
+	}
+
+	if (e->tx_lpi_timer) {
+		dev_err(dev->dev, "Setting EEE Tx LPI timer is not supported\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
 static void ksz_set_xmii(struct ksz_device *dev, int port,
 			 phy_interface_t interface)
 {
@@ -3130,6 +3194,8 @@ static const struct dsa_switch_ops ksz_switch_ops = {
 	.port_txtstamp		= ksz_port_txtstamp,
 	.port_rxtstamp		= ksz_port_rxtstamp,
 	.port_setup_tc		= ksz_setup_tc,
+	.get_mac_eee		= ksz_get_mac_eee,
+	.set_mac_eee		= ksz_set_mac_eee,
 };
 
 struct ksz_device *ksz_switch_alloc(struct device *base, void *priv)
-- 
2.30.2

Re: [PATCH net-next v7 1/9] net: dsa: microchip: enable EEE support

[Arun.Ramadoss]

On Thu, 2023-02-09 at 10:51 +0100, Oleksij Rempel wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you
> know the content is safe
> 
> Some of KSZ9477 family switches provides EEE support. To enable it,
> we
> just need to register set_mac_eee/set_mac_eee handlers and validate
> supported chip version and port.
> 
> Currently supported chip variants are: KSZ8563, KSZ9477, KSZ9563,
> KSZ9567, KSZ9893, KSZ9896, KSZ9897. KSZ8563 supports EEE only with
> 100BaseTX/Full.  Other chips support 100BaseTX/Full and
> 1000BaseTX/Full.
> Low Power Idle configuration is not supported and currently not
> documented in the datasheets.
> 
> EEE PHY specific tunings are not documented in the switch datasheets,
> but can
> overlap with KSZ9131 specification.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> Reviewed-by: Andrew Lunn <andrew@lunn.ch>

Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>

[PATCH net-next v7 2/9] net: phy: add genphy_c45_read_eee_abilities() function

[Oleksij Rempel]

Add generic function for EEE abilities defined by IEEE 802.3
specification. For now following registers are supported:
- IEEE 802.3-2018 45.2.3.10 EEE control and capability 1 (Register 3.20)
- IEEE 802.3cg-2019 45.2.1.186b 10BASE-T1L PMA status register
  (Register 1.2295)

Since I was not able to find any flag signaling support of these
registers, we should detect link mode abilities first and then based on
these abilities doing EEE link modes detection.

Results of EEE ability detection will be stored into new variable
phydev->supported_eee.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/phy/phy-c45.c    | 70 ++++++++++++++++++++++++++++++++++++
 drivers/net/phy/phy_device.c | 16 +++++++++
 include/linux/mdio.h         | 26 ++++++++++++++
 include/linux/phy.h          |  6 ++++
 4 files changed, 118 insertions(+)

diff --git a/drivers/net/phy/phy-c45.c b/drivers/net/phy/phy-c45.c
index 9f9565a4819d..2d10d22e7684 100644
--- a/drivers/net/phy/phy-c45.c
+++ b/drivers/net/phy/phy-c45.c
@@ -661,6 +661,76 @@ int genphy_c45_read_mdix(struct phy_device *phydev)
 }
 EXPORT_SYMBOL_GPL(genphy_c45_read_mdix);
 
+/**
+ * genphy_c45_read_eee_cap1 - read supported EEE link modes from register 3.20
+ * @phydev: target phy_device struct
+ */
+static int genphy_c45_read_eee_cap1(struct phy_device *phydev)
+{
+	int val;
+
+	/* IEEE 802.3-2018 45.2.3.10 EEE control and capability 1
+	 * (Register 3.20)
+	 */
+	val = phy_read_mmd(phydev, MDIO_MMD_PCS, MDIO_PCS_EEE_ABLE);
+	if (val < 0)
+		return val;
+
+	/* The 802.3 2018 standard says the top 2 bits are reserved and should
+	 * read as 0. Also, it seems unlikely anybody will build a PHY which
+	 * supports 100GBASE-R deep sleep all the way down to 100BASE-TX EEE.
+	 * If MDIO_PCS_EEE_ABLE is 0xffff assume EEE is not supported.
+	 */
+	if (val == 0xffff)
+		return 0;
+
+	mii_eee_cap1_mod_linkmode_t(phydev->supported_eee, val);
+
+	/* Some buggy devices indicate EEE link modes in MDIO_PCS_EEE_ABLE
+	 * which they don't support as indicated by BMSR, ESTATUS etc.
+	 */
+	linkmode_and(phydev->supported_eee, phydev->supported_eee,
+		     phydev->supported);
+
+	return 0;
+}
+
+/**
+ * genphy_c45_read_eee_abilities - read supported EEE link modes
+ * @phydev: target phy_device struct
+ */
+int genphy_c45_read_eee_abilities(struct phy_device *phydev)
+{
+	int val;
+
+	/* There is not indicator whether optional register
+	 * "EEE control and capability 1" (3.20) is supported. Read it only
+	 * on devices with appropriate linkmodes.
+	 */
+	if (linkmode_intersects(phydev->supported, PHY_EEE_CAP1_FEATURES)) {
+		val = genphy_c45_read_eee_cap1(phydev);
+		if (val)
+			return val;
+	}
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
+			      phydev->supported)) {
+		/* IEEE 802.3cg-2019 45.2.1.186b 10BASE-T1L PMA status register
+		 * (Register 1.2295)
+		 */
+		val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_10T1L_STAT);
+		if (val < 0)
+			return val;
+
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
+				 phydev->supported_eee,
+				 val & MDIO_PMA_10T1L_STAT_EEE);
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(genphy_c45_read_eee_abilities);
+
 /**
  * genphy_c45_pma_read_abilities - read supported link modes from PMA
  * @phydev: target phy_device struct
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index a3917c7acbd3..66a4e62009bb 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -132,6 +132,18 @@ static const int phy_10gbit_full_features_array[] = {
 	ETHTOOL_LINK_MODE_10000baseT_Full_BIT,
 };
 
+static const int phy_eee_cap1_features_array[] = {
+	ETHTOOL_LINK_MODE_100baseT_Full_BIT,
+	ETHTOOL_LINK_MODE_1000baseT_Full_BIT,
+	ETHTOOL_LINK_MODE_10000baseT_Full_BIT,
+	ETHTOOL_LINK_MODE_1000baseKX_Full_BIT,
+	ETHTOOL_LINK_MODE_10000baseKX4_Full_BIT,
+	ETHTOOL_LINK_MODE_10000baseKR_Full_BIT,
+};
+
+__ETHTOOL_DECLARE_LINK_MODE_MASK(phy_eee_cap1_features) __ro_after_init;
+EXPORT_SYMBOL_GPL(phy_eee_cap1_features);
+
 static void features_init(void)
 {
 	/* 10/100 half/full*/
@@ -213,6 +225,10 @@ static void features_init(void)
 	linkmode_set_bit_array(phy_10gbit_fec_features_array,
 			       ARRAY_SIZE(phy_10gbit_fec_features_array),
 			       phy_10gbit_fec_features);
+	linkmode_set_bit_array(phy_eee_cap1_features_array,
+			       ARRAY_SIZE(phy_eee_cap1_features_array),
+			       phy_eee_cap1_features);
+
 }
 
 void phy_device_free(struct phy_device *phydev)
diff --git a/include/linux/mdio.h b/include/linux/mdio.h
index c0da30d63b1d..e75583f5d967 100644
--- a/include/linux/mdio.h
+++ b/include/linux/mdio.h
@@ -402,6 +402,32 @@ static inline u32 linkmode_adv_to_mii_t1_adv_m_t(unsigned long *advertising)
 	return result;
 }
 
+/**
+ * mii_eee_cap1_mod_linkmode_t()
+ * @adv: target the linkmode advertisement settings
+ * @val: register value
+ *
+ * A function that translates value of following registers to the linkmode:
+ * IEEE 802.3-2018 45.2.3.10 "EEE control and capability 1" register (3.20)
+ * IEEE 802.3-2018 45.2.7.13 "EEE advertisement 1" register (7.60)
+ * IEEE 802.3-2018 45.2.7.14 "EEE "link partner ability 1 register (7.61)
+ */
+static inline void mii_eee_cap1_mod_linkmode_t(unsigned long *adv, u32 val)
+{
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT,
+			 adv, val & MDIO_EEE_100TX);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT,
+			 adv, val & MDIO_EEE_1000T);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT,
+			 adv, val & MDIO_EEE_10GT);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseKX_Full_BIT,
+			 adv, val & MDIO_EEE_1000KX);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_10000baseKX4_Full_BIT,
+			 adv, val & MDIO_EEE_10GKX4);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_10000baseKR_Full_BIT,
+			 adv, val & MDIO_EEE_10GKR);
+}
+
 int __mdiobus_read(struct mii_bus *bus, int addr, u32 regnum);
 int __mdiobus_write(struct mii_bus *bus, int addr, u32 regnum, u16 val);
 int __mdiobus_modify_changed(struct mii_bus *bus, int addr, u32 regnum,
diff --git a/include/linux/phy.h b/include/linux/phy.h
index fbeba4fee8d4..c183a8a27986 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -52,6 +52,7 @@ extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_gbit_all_ports_features) __ro_after_
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_10gbit_features) __ro_after_init;
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_10gbit_fec_features) __ro_after_init;
 extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_10gbit_full_features) __ro_after_init;
+extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_eee_cap1_features) __ro_after_init;
 
 #define PHY_BASIC_FEATURES ((unsigned long *)&phy_basic_features)
 #define PHY_BASIC_T1_FEATURES ((unsigned long *)&phy_basic_t1_features)
@@ -62,6 +63,7 @@ extern __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_10gbit_full_features) __ro_after_ini
 #define PHY_10GBIT_FEATURES ((unsigned long *)&phy_10gbit_features)
 #define PHY_10GBIT_FEC_FEATURES ((unsigned long *)&phy_10gbit_fec_features)
 #define PHY_10GBIT_FULL_FEATURES ((unsigned long *)&phy_10gbit_full_features)
+#define PHY_EEE_CAP1_FEATURES ((unsigned long *)&phy_eee_cap1_features)
 
 extern const int phy_basic_ports_array[3];
 extern const int phy_fibre_port_array[1];
@@ -572,6 +574,7 @@ struct macsec_ops;
  * @supported: Combined MAC/PHY supported linkmodes
  * @advertising: Currently advertised linkmodes
  * @adv_old: Saved advertised while power saving for WoL
+ * @supported_eee: supported PHY EEE linkmodes
  * @lp_advertising: Current link partner advertised linkmodes
  * @host_interfaces: PHY interface modes supported by host
  * @eee_broken_modes: Energy efficient ethernet modes which should be prohibited
@@ -676,6 +679,8 @@ struct phy_device {
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(lp_advertising);
 	/* used with phy_speed_down */
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(adv_old);
+	/* used for eee validation */
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(supported_eee);
 
 	/* Host supported PHY interface types. Should be ignored if empty. */
 	DECLARE_PHY_INTERFACE_MASK(host_interfaces);
@@ -1737,6 +1742,7 @@ int genphy_c45_an_config_aneg(struct phy_device *phydev);
 int genphy_c45_an_disable_aneg(struct phy_device *phydev);
 int genphy_c45_read_mdix(struct phy_device *phydev);
 int genphy_c45_pma_read_abilities(struct phy_device *phydev);
+int genphy_c45_read_eee_abilities(struct phy_device *phydev);
 int genphy_c45_pma_baset1_read_master_slave(struct phy_device *phydev);
 int genphy_c45_read_status(struct phy_device *phydev);
 int genphy_c45_baset1_read_status(struct phy_device *phydev);
-- 
2.30.2

[PATCH net-next v7 3/9] net: phy: micrel: add ksz9477_get_features()

[Oleksij Rempel]

KSZ8563R, which has same PHYID as KSZ9477 family, will change "EEE control
and capability 1" (Register 3.20) content depending on configuration of
"EEE advertisement 1" (Register 7.60). Changes on the 7.60 will affect
3.20 register.

So, instead of depending on register 3.20, driver should set supported_eee.

Proper supported_eee configuration is needed to make use of generic
PHY c45 set/get_eee functions provided by next patches.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/phy/micrel.c | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)

diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index d5b80c31ab91..41eb8df6bfb9 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -1370,6 +1370,26 @@ static int ksz9131_config_aneg(struct phy_device *phydev)
 	return genphy_config_aneg(phydev);
 }
 
+static int ksz9477_get_features(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = genphy_read_abilities(phydev);
+	if (ret)
+		return ret;
+
+	/* The "EEE control and capability 1" (Register 3.20) seems to be
+	 * influenced by the "EEE advertisement 1" (Register 7.60). Changes
+	 * on the 7.60 will affect 3.20. So, we need to construct our own list
+	 * of caps.
+	 * KSZ8563R should have 100BaseTX/Full only.
+	 */
+	linkmode_and(phydev->supported_eee, phydev->supported,
+		     PHY_EEE_CAP1_FEATURES);
+
+	return 0;
+}
+
 #define KSZ8873MLL_GLOBAL_CONTROL_4	0x06
 #define KSZ8873MLL_GLOBAL_CONTROL_4_DUPLEX	BIT(6)
 #define KSZ8873MLL_GLOBAL_CONTROL_4_SPEED	BIT(4)
@@ -3422,6 +3442,7 @@ static struct phy_driver ksphy_driver[] = {
 	.handle_interrupt = kszphy_handle_interrupt,
 	.suspend	= genphy_suspend,
 	.resume		= genphy_resume,
+	.get_features	= ksz9477_get_features,
 } };
 
 module_phy_driver(ksphy_driver);
-- 
2.30.2

[PATCH net-next v7 4/9] net: phy: export phy_check_valid() function

[Oleksij Rempel]

This function will be needed for genphy_c45_ethtool_get_eee() provided
by next patch.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/net/phy/phy.c | 4 ++--
 include/linux/phy.h   | 1 +
 2 files changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 3378ca4f49b6..41cfb24c48c1 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -242,11 +242,11 @@ unsigned int phy_supported_speeds(struct phy_device *phy,
  *
  * Description: Returns true if there is a valid setting, false otherwise.
  */
-static inline bool phy_check_valid(int speed, int duplex,
-				   unsigned long *features)
+bool phy_check_valid(int speed, int duplex, unsigned long *features)
 {
 	return !!phy_lookup_setting(speed, duplex, features, true);
 }
+EXPORT_SYMBOL(phy_check_valid);
 
 /**
  * phy_sanitize_settings - make sure the PHY is set to supported speed and duplex
diff --git a/include/linux/phy.h b/include/linux/phy.h
index c183a8a27986..7a8e541de3f3 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1619,6 +1619,7 @@ int phy_start_aneg(struct phy_device *phydev);
 int phy_aneg_done(struct phy_device *phydev);
 int phy_speed_down(struct phy_device *phydev, bool sync);
 int phy_speed_up(struct phy_device *phydev);
+bool phy_check_valid(int speed, int duplex, unsigned long *features);
 
 int phy_restart_aneg(struct phy_device *phydev);
 int phy_reset_after_clk_enable(struct phy_device *phydev);
-- 
2.30.2

Re: [PATCH net-next v7 4/9] net: phy: export phy_check_valid() function

[Alexander H Duyck]

On Thu, 2023-02-09 at 10:51 +0100, Oleksij Rempel wrote:
> This function will be needed for genphy_c45_ethtool_get_eee() provided
> by next patch.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  drivers/net/phy/phy.c | 4 ++--
>  include/linux/phy.h   | 1 +
>  2 files changed, 3 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
> index 3378ca4f49b6..41cfb24c48c1 100644
> --- a/drivers/net/phy/phy.c
> +++ b/drivers/net/phy/phy.c
> @@ -242,11 +242,11 @@ unsigned int phy_supported_speeds(struct phy_device *phy,
>   *
>   * Description: Returns true if there is a valid setting, false otherwise.
>   */
> -static inline bool phy_check_valid(int speed, int duplex,
> -				   unsigned long *features)
> +bool phy_check_valid(int speed, int duplex, unsigned long *features)
>  {
>  	return !!phy_lookup_setting(speed, duplex, features, true);
>  }
> +EXPORT_SYMBOL(phy_check_valid);
>  
>  /**
>   * phy_sanitize_settings - make sure the PHY is set to supported speed and duplex
> diff --git a/include/linux/phy.h b/include/linux/phy.h
> index c183a8a27986..7a8e541de3f3 100644
> --- a/include/linux/phy.h
> +++ b/include/linux/phy.h
> @@ -1619,6 +1619,7 @@ int phy_start_aneg(struct phy_device *phydev);
>  int phy_aneg_done(struct phy_device *phydev);
>  int phy_speed_down(struct phy_device *phydev, bool sync);
>  int phy_speed_up(struct phy_device *phydev);
> +bool phy_check_valid(int speed, int duplex, unsigned long *features);
>  
>  int phy_restart_aneg(struct phy_device *phydev);
>  int phy_reset_after_clk_enable(struct phy_device *phydev);

Looks good to me.

Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>

[PATCH net-next v7 5/9] net: phy: add genphy_c45_ethtool_get/set_eee() support

[Oleksij Rempel]

Add replacement for phy_ethtool_get/set_eee() functions.

Current phy_ethtool_get/set_eee() implementation is great and it is
possible to make it even better:
- this functionality is for devices implementing parts of IEEE 802.3
  specification beyond Clause 22. The better place for this code is
  phy-c45.c
- currently it is able to do read/write operations on PHYs with
  different abilities to not existing registers. It is better to
  use stored supported_eee abilities to avoid false read/write
  operations.
- the eee_active detection will provide wrong results on not supported
  link modes. It is better to validate speed/duplex properties against
  supported EEE link modes.
- it is able to support only limited amount of link modes. We have more
  EEE link modes...

By refactoring this code I address most of this point except of the last
one. Adding additional EEE link modes will need more work.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/net/phy/phy-c45.c | 238 ++++++++++++++++++++++++++++++++++++++
 include/linux/mdio.h      |  58 ++++++++++
 include/linux/phy.h       |   7 ++
 include/uapi/linux/mdio.h |   8 ++
 4 files changed, 311 insertions(+)

diff --git a/drivers/net/phy/phy-c45.c b/drivers/net/phy/phy-c45.c
index 2d10d22e7684..b4910c4c21d7 100644
--- a/drivers/net/phy/phy-c45.c
+++ b/drivers/net/phy/phy-c45.c
@@ -661,6 +661,129 @@ int genphy_c45_read_mdix(struct phy_device *phydev)
 }
 EXPORT_SYMBOL_GPL(genphy_c45_read_mdix);
 
+/**
+ * genphy_c45_write_eee_adv - write advertised EEE link modes
+ * @phydev: target phy_device struct
+ * @adv: the linkmode advertisement settings
+ */
+int genphy_c45_write_eee_adv(struct phy_device *phydev, unsigned long *adv)
+{
+	int val, changed;
+
+	if (linkmode_intersects(phydev->supported, PHY_EEE_CAP1_FEATURES)) {
+		val = linkmode_to_mii_eee_cap1_t(adv);
+
+		/* In eee_broken_modes are stored MDIO_AN_EEE_ADV specific raw
+		 * register values.
+		 */
+		val &= ~phydev->eee_broken_modes;
+
+		/* IEEE 802.3-2018 45.2.7.13 EEE advertisement 1
+		 * (Register 7.60)
+		 */
+		val = phy_modify_mmd_changed(phydev, MDIO_MMD_AN,
+					     MDIO_AN_EEE_ADV,
+					     MDIO_EEE_100TX | MDIO_EEE_1000T |
+					     MDIO_EEE_10GT | MDIO_EEE_1000KX |
+					     MDIO_EEE_10GKX4 | MDIO_EEE_10GKR,
+					     val);
+		if (val < 0)
+			return val;
+		if (val > 0)
+			changed = 1;
+	}
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
+			      phydev->supported_eee)) {
+		val = linkmode_adv_to_mii_10base_t1_t(adv);
+		/* IEEE 802.3cg-2019 45.2.7.25 10BASE-T1 AN control register
+		 * (Register 7.526)
+		 */
+		val = phy_modify_mmd_changed(phydev, MDIO_MMD_AN,
+					     MDIO_AN_10BT1_AN_CTRL,
+					     MDIO_AN_10BT1_AN_CTRL_ADV_EEE_T1L,
+					     val);
+		if (val < 0)
+			return val;
+		if (val > 0)
+			changed = 1;
+	}
+
+	return changed;
+}
+
+/**
+ * genphy_c45_read_eee_adv - read advertised EEE link modes
+ * @phydev: target phy_device struct
+ * @adv: the linkmode advertisement status
+ */
+static int genphy_c45_read_eee_adv(struct phy_device *phydev,
+				   unsigned long *adv)
+{
+	int val;
+
+	if (linkmode_intersects(phydev->supported, PHY_EEE_CAP1_FEATURES)) {
+		/* IEEE 802.3-2018 45.2.7.13 EEE advertisement 1
+		 * (Register 7.60)
+		 */
+		val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV);
+		if (val < 0)
+			return val;
+
+		mii_eee_cap1_mod_linkmode_t(adv, val);
+	}
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
+			      phydev->supported_eee)) {
+		/* IEEE 802.3cg-2019 45.2.7.25 10BASE-T1 AN control register
+		 * (Register 7.526)
+		 */
+		val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_10BT1_AN_CTRL);
+		if (val < 0)
+			return val;
+
+		mii_10base_t1_adv_mod_linkmode_t(adv, val);
+	}
+
+	return 0;
+}
+
+/**
+ * genphy_c45_read_eee_lpa - read advertised LP EEE link modes
+ * @phydev: target phy_device struct
+ * @lpa: the linkmode LP advertisement status
+ */
+static int genphy_c45_read_eee_lpa(struct phy_device *phydev,
+				   unsigned long *lpa)
+{
+	int val;
+
+	if (linkmode_intersects(phydev->supported, PHY_EEE_CAP1_FEATURES)) {
+		/* IEEE 802.3-2018 45.2.7.14 EEE link partner ability 1
+		 * (Register 7.61)
+		 */
+		val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_LPABLE);
+		if (val < 0)
+			return val;
+
+		mii_eee_cap1_mod_linkmode_t(lpa, val);
+	}
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
+			      phydev->supported_eee)) {
+		/* IEEE 802.3cg-2019 45.2.7.26 10BASE-T1 AN status register
+		 * (Register 7.527)
+		 */
+		val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_10BT1_AN_STAT);
+		if (val < 0)
+			return val;
+
+		mii_10base_t1_adv_mod_linkmode_t(lpa, val);
+	}
+
+	return 0;
+}
+
 /**
  * genphy_c45_read_eee_cap1 - read supported EEE link modes from register 3.20
  * @phydev: target phy_device struct
@@ -1194,6 +1317,121 @@ int genphy_c45_plca_get_status(struct phy_device *phydev,
 }
 EXPORT_SYMBOL_GPL(genphy_c45_plca_get_status);
 
+/**
+ * genphy_c45_eee_is_active - get EEE status
+ * @phydev: target phy_device struct
+ * @adv: variable to store advertised linkmodes
+ * @lp: variable to store LP advertised linkmodes
+ * @is_enabled: variable to store EEE enabled/disabled configuration value
+ *
+ * Description: this function will read local and link partner PHY
+ * advertisements. Compare them return current EEE state.
+ */
+int genphy_c45_eee_is_active(struct phy_device *phydev, unsigned long *adv,
+			     unsigned long *lp, bool *is_enabled)
+{
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(tmp_adv) = {};
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(tmp_lp) = {};
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(common);
+	bool eee_enabled, eee_active;
+	int ret;
+
+	ret = genphy_c45_read_eee_adv(phydev, tmp_adv);
+	if (ret)
+		return ret;
+
+	ret = genphy_c45_read_eee_lpa(phydev, tmp_lp);
+	if (ret)
+		return ret;
+
+	eee_enabled = !linkmode_empty(tmp_adv);
+	linkmode_and(common, tmp_adv, tmp_lp);
+	if (eee_enabled && !linkmode_empty(common))
+		eee_active = phy_check_valid(phydev->speed, phydev->duplex,
+					     common);
+	else
+		eee_active = false;
+
+	if (adv)
+		linkmode_copy(adv, tmp_adv);
+	if (lp)
+		linkmode_copy(lp, tmp_lp);
+	if (is_enabled)
+		*is_enabled = eee_enabled;
+
+	return eee_active;
+}
+EXPORT_SYMBOL(genphy_c45_eee_is_active);
+
+/**
+ * genphy_c45_ethtool_get_eee - get EEE supported and status
+ * @phydev: target phy_device struct
+ * @data: ethtool_eee data
+ *
+ * Description: it reports the Supported/Advertisement/LP Advertisement
+ * capabilities.
+ */
+int genphy_c45_ethtool_get_eee(struct phy_device *phydev,
+			       struct ethtool_eee *data)
+{
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(adv) = {};
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(lp) = {};
+	bool overflow = false, is_enabled;
+	int ret;
+
+	ret = genphy_c45_eee_is_active(phydev, adv, lp, &is_enabled);
+	if (ret < 0)
+		return ret;
+
+	data->eee_enabled = is_enabled;
+	data->eee_active = ret;
+
+	if (!ethtool_convert_link_mode_to_legacy_u32(&data->supported,
+						     phydev->supported_eee))
+		overflow = true;
+	if (!ethtool_convert_link_mode_to_legacy_u32(&data->advertised, adv))
+		overflow = true;
+	if (!ethtool_convert_link_mode_to_legacy_u32(&data->lp_advertised, lp))
+		overflow = true;
+
+	if (overflow)
+		phydev_warn(phydev, "Not all supported or advertised EEE link modes were passed to the user space\n");
+
+	return 0;
+}
+EXPORT_SYMBOL(genphy_c45_ethtool_get_eee);
+
+/**
+ * genphy_c45_ethtool_set_eee - get EEE supported and status
+ * @phydev: target phy_device struct
+ * @data: ethtool_eee data
+ *
+ * Description: it reportes the Supported/Advertisement/LP Advertisement
+ * capabilities.
+ */
+int genphy_c45_ethtool_set_eee(struct phy_device *phydev,
+			       struct ethtool_eee *data)
+{
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(adv) = {};
+	int ret;
+
+	if (data->eee_enabled) {
+		if (data->advertised)
+			adv[0] = data->advertised;
+		else
+			linkmode_copy(adv, phydev->supported_eee);
+	}
+
+	ret = genphy_c45_write_eee_adv(phydev, adv);
+	if (ret < 0)
+		return ret;
+	if (ret > 0)
+		return phy_restart_aneg(phydev);
+
+	return 0;
+}
+EXPORT_SYMBOL(genphy_c45_ethtool_set_eee);
+
 struct phy_driver genphy_c45_driver = {
 	.phy_id         = 0xffffffff,
 	.phy_id_mask    = 0xffffffff,
diff --git a/include/linux/mdio.h b/include/linux/mdio.h
index e75583f5d967..e3568e44efd0 100644
--- a/include/linux/mdio.h
+++ b/include/linux/mdio.h
@@ -428,6 +428,64 @@ static inline void mii_eee_cap1_mod_linkmode_t(unsigned long *adv, u32 val)
 			 adv, val & MDIO_EEE_10GKR);
 }
 
+/**
+ * mii_eee_cap1_mod_linkmode_t
+ * @adv: the linkmode advertisement settings
+ *
+ * A function that translates linkmode to value for IEEE 802.3-2018 45.2.7.13
+ * "EEE advertisement 1" register (7.60)
+ */
+static inline u32 linkmode_to_mii_eee_cap1_t(unsigned long *adv)
+{
+	u32 result = 0;
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, adv))
+		result |= MDIO_EEE_100TX;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, adv))
+		result |= MDIO_EEE_1000T;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT, adv))
+		result |= MDIO_EEE_10GT;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseKX_Full_BIT, adv))
+		result |= MDIO_EEE_1000KX;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseKX4_Full_BIT, adv))
+		result |= MDIO_EEE_10GKX4;
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseKR_Full_BIT, adv))
+		result |= MDIO_EEE_10GKR;
+
+	return result;
+}
+
+/**
+ * mii_10base_t1_adv_mod_linkmode_t
+ * @adv: linkmode advertisement settings
+ * @val: register value
+ *
+ * A function that translates IEEE 802.3cg-2019 45.2.7.26 "10BASE-T1 AN status"
+ * register (7.527) value to the linkmode.
+ */
+static inline void mii_10base_t1_adv_mod_linkmode_t(unsigned long *adv, u16 val)
+{
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT,
+			 adv, val & MDIO_AN_10BT1_AN_CTRL_ADV_EEE_T1L);
+}
+
+/**
+ * linkmode_adv_to_mii_10base_t1_t
+ * @adv: linkmode advertisement settings
+ *
+ * A function that translates the linkmode to IEEE 802.3cg-2019 45.2.7.25
+ * "10BASE-T1 AN control" register (7.526) value.
+ */
+static inline u32 linkmode_adv_to_mii_10base_t1_t(unsigned long *adv)
+{
+	u32 result = 0;
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT, adv))
+		result |= MDIO_AN_10BT1_AN_CTRL_ADV_EEE_T1L;
+
+	return result;
+}
+
 int __mdiobus_read(struct mii_bus *bus, int addr, u32 regnum);
 int __mdiobus_write(struct mii_bus *bus, int addr, u32 regnum, u16 val);
 int __mdiobus_modify_changed(struct mii_bus *bus, int addr, u32 regnum,
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 7a8e541de3f3..727bff531a14 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -1758,6 +1758,13 @@ int genphy_c45_plca_set_cfg(struct phy_device *phydev,
 			    const struct phy_plca_cfg *plca_cfg);
 int genphy_c45_plca_get_status(struct phy_device *phydev,
 			       struct phy_plca_status *plca_st);
+int genphy_c45_eee_is_active(struct phy_device *phydev, unsigned long *adv,
+			     unsigned long *lp, bool *is_enabled);
+int genphy_c45_ethtool_get_eee(struct phy_device *phydev,
+			       struct ethtool_eee *data);
+int genphy_c45_ethtool_set_eee(struct phy_device *phydev,
+			       struct ethtool_eee *data);
+int genphy_c45_write_eee_adv(struct phy_device *phydev, unsigned long *adv);
 
 /* Generic C45 PHY driver */
 extern struct phy_driver genphy_c45_driver;
diff --git a/include/uapi/linux/mdio.h b/include/uapi/linux/mdio.h
index 75b7257a51e1..256b463e47a6 100644
--- a/include/uapi/linux/mdio.h
+++ b/include/uapi/linux/mdio.h
@@ -79,6 +79,8 @@
 #define MDIO_AN_T1_LP_L		517	/* BASE-T1 AN LP Base Page ability register [15:0] */
 #define MDIO_AN_T1_LP_M		518	/* BASE-T1 AN LP Base Page ability register [31:16] */
 #define MDIO_AN_T1_LP_H		519	/* BASE-T1 AN LP Base Page ability register [47:32] */
+#define MDIO_AN_10BT1_AN_CTRL	526	/* 10BASE-T1 AN control register */
+#define MDIO_AN_10BT1_AN_STAT	527	/* 10BASE-T1 AN status register */
 #define MDIO_PMA_PMD_BT1_CTRL	2100	/* BASE-T1 PMA/PMD control register */
 
 /* LASI (Link Alarm Status Interrupt) registers, defined by XENPAK MSA. */
@@ -340,6 +342,12 @@
 #define MDIO_AN_T1_LP_H_10L_TX_HI_REQ	0x1000	/* 10BASE-T1L High Level LP Transmit Request */
 #define MDIO_AN_T1_LP_H_10L_TX_HI	0x2000	/* 10BASE-T1L High Level LP Transmit Ability */
 
+/* 10BASE-T1 AN control register */
+#define MDIO_AN_10BT1_AN_CTRL_ADV_EEE_T1L	0x4000 /* 10BASE-T1L EEE ability advertisement */
+
+/* 10BASE-T1 AN status register */
+#define MDIO_AN_10BT1_AN_STAT_LPA_EEE_T1L	0x4000 /* 10BASE-T1L LP EEE ability advertisement */
+
 /* BASE-T1 PMA/PMD control register */
 #define MDIO_PMA_PMD_BT1_CTRL_CFG_MST	0x4000 /* MASTER-SLAVE config value */
 
-- 
2.30.2

Re: [PATCH net-next v7 5/9] net: phy: add genphy_c45_ethtool_get/set_eee() support

[Alexander H Duyck]

On Thu, 2023-02-09 at 10:51 +0100, Oleksij Rempel wrote:
> Add replacement for phy_ethtool_get/set_eee() functions.
> 
> Current phy_ethtool_get/set_eee() implementation is great and it is
> possible to make it even better:
> - this functionality is for devices implementing parts of IEEE 802.3
>   specification beyond Clause 22. The better place for this code is
>   phy-c45.c
> - currently it is able to do read/write operations on PHYs with
>   different abilities to not existing registers. It is better to
>   use stored supported_eee abilities to avoid false read/write
>   operations.
> - the eee_active detection will provide wrong results on not supported
>   link modes. It is better to validate speed/duplex properties against
>   supported EEE link modes.
> - it is able to support only limited amount of link modes. We have more
>   EEE link modes...
> 
> By refactoring this code I address most of this point except of the last
> one. Adding additional EEE link modes will need more work.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  drivers/net/phy/phy-c45.c | 238 ++++++++++++++++++++++++++++++++++++++
>  include/linux/mdio.h      |  58 ++++++++++
>  include/linux/phy.h       |   7 ++
>  include/uapi/linux/mdio.h |   8 ++
>  4 files changed, 311 insertions(+)
> 
> 

<...>

> diff --git a/include/linux/mdio.h b/include/linux/mdio.h
> index e75583f5d967..e3568e44efd0 100644
> --- a/include/linux/mdio.h
> +++ b/include/linux/mdio.h
> @@ -428,6 +428,64 @@ static inline void mii_eee_cap1_mod_linkmode_t(unsigned long *adv, u32 val)
>  			 adv, val & MDIO_EEE_10GKR);
>  }
>  
> +/**
> + * mii_eee_cap1_mod_linkmode_t
> + * @adv: the linkmode advertisement settings
> + *
> + * A function that translates linkmode to value for IEEE 802.3-2018 45.2.7.13
> + * "EEE advertisement 1" register (7.60)
> + */
> +static inline u32 linkmode_to_mii_eee_cap1_t(unsigned long *adv)

So the function comments don't match the name for the function. Perhaps
a copy/paste error? Otherwise the rest of the function description
looks fine.

> +{
> +	u32 result = 0;
> +
> +	if (linkmode_test_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, adv))
> +		result |= MDIO_EEE_100TX;
> +	if (linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, adv))
> +		result |= MDIO_EEE_1000T;
> +	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT, adv))
> +		result |= MDIO_EEE_10GT;
> +	if (linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseKX_Full_BIT, adv))
> +		result |= MDIO_EEE_1000KX;
> +	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseKX4_Full_BIT, adv))
> +		result |= MDIO_EEE_10GKX4;
> +	if (linkmode_test_bit(ETHTOOL_LINK_MODE_10000baseKR_Full_BIT, adv))
> +		result |= MDIO_EEE_10GKR;
> +
> +	return result;
> +}
> +

[PATCH net-next v7 6/9] net: phy: c22: migrate to genphy_c45_write_eee_adv()

[Oleksij Rempel]

Migrate from genphy_config_eee_advert() to genphy_c45_write_eee_adv().

It should work as before except write operation to the EEE adv registers
will be done only if some EEE abilities was detected.

If some driver will have a regression, related driver should provide own
.get_features callback. See micrel.c:ksz9477_get_features() as example.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/phy/phy_device.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 66a4e62009bb..8d927c5e3bf8 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -2231,7 +2231,10 @@ int __genphy_config_aneg(struct phy_device *phydev, bool changed)
 {
 	int err;
 
-	if (genphy_config_eee_advert(phydev))
+	err = genphy_c45_write_eee_adv(phydev, phydev->supported_eee);
+	if (err < 0)
+		return err;
+	else if (err)
 		changed = true;
 
 	err = genphy_setup_master_slave(phydev);
@@ -2653,6 +2656,11 @@ int genphy_read_abilities(struct phy_device *phydev)
 				 phydev->supported, val & ESTATUS_1000_XFULL);
 	}
 
+	/* This is optional functionality. If not supported, we may get an error
+	 * which should be ignored.
+	 */
+	genphy_c45_read_eee_abilities(phydev);
+
 	return 0;
 }
 EXPORT_SYMBOL(genphy_read_abilities);
-- 
2.30.2

[PATCH net-next v7 7/9] net: phy: c45: migrate to genphy_c45_write_eee_adv()

[Oleksij Rempel]

Migrate from genphy_config_eee_advert() to genphy_c45_write_eee_adv().

It should work as before except write operation to the EEE adv registers
will be done only if some EEE abilities was detected.

If some driver will have a regression, related driver should provide own
.get_features callback. See micrel.c:ksz9477_get_features() as example.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/phy/phy-c45.c | 11 ++++++++++-
 1 file changed, 10 insertions(+), 1 deletion(-)

diff --git a/drivers/net/phy/phy-c45.c b/drivers/net/phy/phy-c45.c
index b4910c4c21d7..ef36582adbeb 100644
--- a/drivers/net/phy/phy-c45.c
+++ b/drivers/net/phy/phy-c45.c
@@ -262,7 +262,11 @@ int genphy_c45_an_config_aneg(struct phy_device *phydev)
 	linkmode_and(phydev->advertising, phydev->advertising,
 		     phydev->supported);
 
-	changed = genphy_config_eee_advert(phydev);
+	ret = genphy_c45_write_eee_adv(phydev, phydev->supported_eee);
+	if (ret < 0)
+		return ret;
+	else if (ret)
+		changed = true;
 
 	if (genphy_c45_baset1_able(phydev))
 		return genphy_c45_baset1_an_config_aneg(phydev);
@@ -968,6 +972,11 @@ int genphy_c45_pma_read_abilities(struct phy_device *phydev)
 		}
 	}
 
+	/* This is optional functionality. If not supported, we may get an error
+	 * which should be ignored.
+	 */
+	genphy_c45_read_eee_abilities(phydev);
+
 	return 0;
 }
 EXPORT_SYMBOL_GPL(genphy_c45_pma_read_abilities);
-- 
2.30.2

[PATCH net-next v7 8/9] net: phy: migrate phy_init_eee() to genphy_c45_eee_is_active()

[Oleksij Rempel]

Reduce code duplicated by migrating phy_init_eee() to
genphy_c45_eee_is_active().

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/phy/phy.c | 89 +++++++------------------------------------
 1 file changed, 14 insertions(+), 75 deletions(-)

diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 41cfb24c48c1..36533746630e 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -1457,30 +1457,6 @@ void phy_mac_interrupt(struct phy_device *phydev)
 }
 EXPORT_SYMBOL(phy_mac_interrupt);
 
-static void mmd_eee_adv_to_linkmode(unsigned long *advertising, u16 eee_adv)
-{
-	linkmode_zero(advertising);
-
-	if (eee_adv & MDIO_EEE_100TX)
-		linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT,
-				 advertising);
-	if (eee_adv & MDIO_EEE_1000T)
-		linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT,
-				 advertising);
-	if (eee_adv & MDIO_EEE_10GT)
-		linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseT_Full_BIT,
-				 advertising);
-	if (eee_adv & MDIO_EEE_1000KX)
-		linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseKX_Full_BIT,
-				 advertising);
-	if (eee_adv & MDIO_EEE_10GKX4)
-		linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseKX4_Full_BIT,
-				 advertising);
-	if (eee_adv & MDIO_EEE_10GKR)
-		linkmode_set_bit(ETHTOOL_LINK_MODE_10000baseKR_Full_BIT,
-				 advertising);
-}
-
 /**
  * phy_init_eee - init and check the EEE feature
  * @phydev: target phy_device struct
@@ -1493,62 +1469,25 @@ static void mmd_eee_adv_to_linkmode(unsigned long *advertising, u16 eee_adv)
  */
 int phy_init_eee(struct phy_device *phydev, bool clk_stop_enable)
 {
+	int ret;
+
 	if (!phydev->drv)
 		return -EIO;
 
-	/* According to 802.3az,the EEE is supported only in full duplex-mode.
-	 */
-	if (phydev->duplex == DUPLEX_FULL) {
-		__ETHTOOL_DECLARE_LINK_MODE_MASK(common);
-		__ETHTOOL_DECLARE_LINK_MODE_MASK(lp);
-		__ETHTOOL_DECLARE_LINK_MODE_MASK(adv);
-		int eee_lp, eee_cap, eee_adv;
-		int status;
-		u32 cap;
-
-		/* Read phy status to properly get the right settings */
-		status = phy_read_status(phydev);
-		if (status)
-			return status;
-
-		/* First check if the EEE ability is supported */
-		eee_cap = phy_read_mmd(phydev, MDIO_MMD_PCS, MDIO_PCS_EEE_ABLE);
-		if (eee_cap <= 0)
-			goto eee_exit_err;
-
-		cap = mmd_eee_cap_to_ethtool_sup_t(eee_cap);
-		if (!cap)
-			goto eee_exit_err;
-
-		/* Check which link settings negotiated and verify it in
-		 * the EEE advertising registers.
-		 */
-		eee_lp = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_LPABLE);
-		if (eee_lp <= 0)
-			goto eee_exit_err;
-
-		eee_adv = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV);
-		if (eee_adv <= 0)
-			goto eee_exit_err;
-
-		mmd_eee_adv_to_linkmode(adv, eee_adv);
-		mmd_eee_adv_to_linkmode(lp, eee_lp);
-		linkmode_and(common, adv, lp);
-
-		if (!phy_check_valid(phydev->speed, phydev->duplex, common))
-			goto eee_exit_err;
+	ret = genphy_c45_eee_is_active(phydev, NULL, NULL, NULL);
+	if (ret < 0)
+		return ret;
+	if (!ret)
+		return -EPROTONOSUPPORT;
 
-		if (clk_stop_enable)
-			/* Configure the PHY to stop receiving xMII
-			 * clock while it is signaling LPI.
-			 */
-			phy_set_bits_mmd(phydev, MDIO_MMD_PCS, MDIO_CTRL1,
-					 MDIO_PCS_CTRL1_CLKSTOP_EN);
+	if (clk_stop_enable)
+		/* Configure the PHY to stop receiving xMII
+		 * clock while it is signaling LPI.
+		 */
+		ret = phy_set_bits_mmd(phydev, MDIO_MMD_PCS, MDIO_CTRL1,
+				       MDIO_PCS_CTRL1_CLKSTOP_EN);
 
-		return 0; /* EEE supported */
-	}
-eee_exit_err:
-	return -EPROTONOSUPPORT;
+	return ret < 0 ? ret : 0;
 }
 EXPORT_SYMBOL(phy_init_eee);
 
-- 
2.30.2

[PATCH net-next v7 9/9] net: phy: start using genphy_c45_ethtool_get/set_eee()

[Oleksij Rempel]

All preparations are done. Now we can start using new functions and remove
the old code.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/phy/phy.c | 60 ++-----------------------------------------
 1 file changed, 2 insertions(+), 58 deletions(-)

diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 36533746630e..2f1041a7211e 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -1517,33 +1517,10 @@ EXPORT_SYMBOL(phy_get_eee_err);
  */
 int phy_ethtool_get_eee(struct phy_device *phydev, struct ethtool_eee *data)
 {
-	int val;
-
 	if (!phydev->drv)
 		return -EIO;
 
-	/* Get Supported EEE */
-	val = phy_read_mmd(phydev, MDIO_MMD_PCS, MDIO_PCS_EEE_ABLE);
-	if (val < 0)
-		return val;
-	data->supported = mmd_eee_cap_to_ethtool_sup_t(val);
-
-	/* Get advertisement EEE */
-	val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV);
-	if (val < 0)
-		return val;
-	data->advertised = mmd_eee_adv_to_ethtool_adv_t(val);
-	data->eee_enabled = !!data->advertised;
-
-	/* Get LP advertisement EEE */
-	val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_LPABLE);
-	if (val < 0)
-		return val;
-	data->lp_advertised = mmd_eee_adv_to_ethtool_adv_t(val);
-
-	data->eee_active = !!(data->advertised & data->lp_advertised);
-
-	return 0;
+	return genphy_c45_ethtool_get_eee(phydev, data);
 }
 EXPORT_SYMBOL(phy_ethtool_get_eee);
 
@@ -1556,43 +1533,10 @@ EXPORT_SYMBOL(phy_ethtool_get_eee);
  */
 int phy_ethtool_set_eee(struct phy_device *phydev, struct ethtool_eee *data)
 {
-	int cap, old_adv, adv = 0, ret;
-
 	if (!phydev->drv)
 		return -EIO;
 
-	/* Get Supported EEE */
-	cap = phy_read_mmd(phydev, MDIO_MMD_PCS, MDIO_PCS_EEE_ABLE);
-	if (cap < 0)
-		return cap;
-
-	old_adv = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV);
-	if (old_adv < 0)
-		return old_adv;
-
-	if (data->eee_enabled) {
-		adv = !data->advertised ? cap :
-		      ethtool_adv_to_mmd_eee_adv_t(data->advertised) & cap;
-		/* Mask prohibited EEE modes */
-		adv &= ~phydev->eee_broken_modes;
-	}
-
-	if (old_adv != adv) {
-		ret = phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV, adv);
-		if (ret < 0)
-			return ret;
-
-		/* Restart autonegotiation so the new modes get sent to the
-		 * link partner.
-		 */
-		if (phydev->autoneg == AUTONEG_ENABLE) {
-			ret = phy_restart_aneg(phydev);
-			if (ret < 0)
-				return ret;
-		}
-	}
-
-	return 0;
+	return genphy_c45_ethtool_set_eee(phydev, data);
 }
 EXPORT_SYMBOL(phy_ethtool_set_eee);
 
-- 
2.30.2