From: Andrew Lunn <andrew@lunn.ch>
To: netdev <netdev@vger.kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>,
Heiner Kallweit <hkallweit1@gmail.com>,
Russell King <rmk+kernel@armlinux.org.uk>,
Oleksij Rempel <linux@rempel-privat.de>,
Andrew Lunn <andrew@lunn.ch>
Subject: [RFC/RFTv3 23/24] net: phylib: call phy_support_eee() in MAC drivers which support EEE
Date: Fri, 31 Mar 2023 02:55:17 +0200 [thread overview]
Message-ID: <20230331005518.2134652-24-andrew@lunn.ch> (raw)
In-Reply-To: <20230331005518.2134652-1-andrew@lunn.ch>
For MAC drivers making use of phylib, and which support EEE, call
phy_support_eee() before starting the PHY.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/ethernet/broadcom/genet/bcmmii.c | 2 ++
drivers/net/ethernet/freescale/fec_main.c | 3 +++
drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c | 3 +++
drivers/net/usb/lan78xx.c | 2 ++
4 files changed, 10 insertions(+)
diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c
index 6c39839762a7..4175042865ec 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -376,6 +376,8 @@ int bcmgenet_mii_probe(struct net_device *dev)
}
}
+ phy_support_eee(dev->phydev);
+
/* Configure port multiplexer based on what the probed PHY device since
* reading the 'max-speed' property determines the maximum supported
* PHY speed which is needed for bcmgenet_mii_config() to configure
diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index fda1f9ff32b9..09c55430c614 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -2348,6 +2348,9 @@ static int fec_enet_mii_probe(struct net_device *ndev)
else
phy_set_max_speed(phy_dev, 100);
+ if (fep->quirks & FEC_QUIRK_HAS_EEE)
+ phy_support_eee(phy_dev);
+
fep->link = 0;
fep->full_duplex = 0;
diff --git a/drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c b/drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c
index cf549a524674..060280c4bc0a 100644
--- a/drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c
+++ b/drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c
@@ -286,6 +286,9 @@ static int sxgbe_init_phy(struct net_device *ndev)
return -ENODEV;
}
+ if (priv->hw_cap.eee)
+ phy_support_eee(phydev);
+
netdev_dbg(ndev, "%s: attached to PHY (UID 0x%x) Link = %d\n",
__func__, phydev->phy_id, phydev->link);
diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c
index 729183e57080..fcf367ad9b0b 100644
--- a/drivers/net/usb/lan78xx.c
+++ b/drivers/net/usb/lan78xx.c
@@ -2406,6 +2406,8 @@ static int lan78xx_phy_init(struct lan78xx_net *dev)
mii_adv_to_linkmode_adv_t(fc, mii_adv);
linkmode_or(phydev->advertising, fc, phydev->advertising);
+ phy_support_eee(phydev);
+
if (phydev->mdio.dev.of_node) {
u32 reg;
int len;
--
2.40.0
next prev parent reply other threads:[~2023-03-31 0:56 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-03-31 0:54 [RFC/RFTv3 00/24] net: ethernet: Rework EEE Andrew Lunn
2023-03-31 0:54 ` [RFC/RFTv3 01/24] net: phy: Add phydev->eee_active to simplify adjust link callbacks Andrew Lunn
2023-05-30 17:51 ` Florian Fainelli
2023-03-31 0:54 ` [RFC/RFTv3 02/24] net: phylink: Add mac_set_eee() callback Andrew Lunn
2023-03-31 0:54 ` [RFC/RFTv3 03/24] net: phy: Add helper to set EEE Clock stop enable bit Andrew Lunn
2023-03-31 0:54 ` [RFC/RFTv3 04/24] net: phy: Keep track of EEE tx_lpi_enabled Andrew Lunn
2023-05-30 18:11 ` Florian Fainelli
2023-05-30 18:14 ` Russell King (Oracle)
2023-03-31 0:54 ` [RFC/RFTv3 05/24] net: phy: Immediately call adjust_link if only tx_lpi_enabled changes Andrew Lunn
2023-03-31 0:55 ` [RFC/RFTv3 06/24] net: phylink: Handle change in EEE from phylib Andrew Lunn
2023-03-31 0:55 ` [RFC/RFTv3 07/24] net: marvell: mvneta: Simplify EEE configuration Andrew Lunn
2023-05-30 18:03 ` Florian Fainelli
2023-03-31 0:55 ` [RFC/RFTv3 08/24] net: stmmac: Drop usage of phy_init_eee() Andrew Lunn
2023-03-31 0:55 ` [RFC/RFTv3 09/24] net: stmmac: Simplify ethtool get eee Andrew Lunn
2023-05-19 7:11 ` Oleksij Rempel
2023-03-31 0:55 ` [RFC/RFTv3 10/24] net: lan743x: Fixup EEE Andrew Lunn
2023-05-30 18:03 ` Florian Fainelli
2023-03-31 0:55 ` [RFC/RFTv3 11/24] net: fec: Move fec_enet_eee_mode_set() and helper earlier Andrew Lunn
2023-03-31 0:55 ` [RFC/RFTv3 12/24] net: FEC: Fixup EEE Andrew Lunn
2023-05-19 10:27 ` Oleksij Rempel
2023-03-31 0:55 ` [RFC/RFTv3 13/24] net: genet: " Andrew Lunn
2023-05-30 18:01 ` Florian Fainelli
2023-03-31 0:55 ` [RFC/RFTv3 14/24] net: sxgdb: " Andrew Lunn
2023-03-31 0:55 ` [RFC/RFTv3 15/24] net: dsa: mt7530: Swap to using phydev->eee_active Andrew Lunn
2023-03-31 0:55 ` [RFC/RFTv3 16/24] net: dsa: b53: " Andrew Lunn
2023-05-30 18:05 ` Florian Fainelli
2023-03-31 0:55 ` [RFC/RFTv3 17/24] net: phylink: Remove unused phylink_init_eee() Andrew Lunn
2023-03-31 0:55 ` [RFC/RFTv3 18/24] net: phy: remove unused phy_init_eee() Andrew Lunn
2023-03-31 0:55 ` [RFC/RFTv3 19/24] net: usb: lan78xx: Fixup EEE Andrew Lunn
2023-03-31 0:55 ` [RFC/RFTv3 20/24] net: phy: Add phy_support_eee() indicating MAC support EEE Andrew Lunn
2023-05-30 18:16 ` Florian Fainelli
2023-03-31 0:55 ` [RFC/RFTv3 21/24] net: phylink: Add MAC_EEE to mac_capabilites Andrew Lunn
2023-05-30 18:18 ` Florian Fainelli
2023-03-31 0:55 ` [RFC/RFTv3 22/24] net: phylink: Extend mac_capabilities in MAC drivers which support EEE Andrew Lunn
2023-03-31 0:55 ` Andrew Lunn [this message]
2023-03-31 0:55 ` [RFC/RFTv3 24/24] net: phy: Disable EEE advertisement by default Andrew Lunn
2023-05-26 8:56 ` [RFC/RFTv3 00/24] net: ethernet: Rework EEE Oleksij Rempel
2023-05-26 12:08 ` Andrew Lunn
2023-05-26 16:13 ` Florian Fainelli
2023-05-30 18:31 ` Florian Fainelli
2023-05-30 19:35 ` Russell King (Oracle)
2023-05-30 19:49 ` Russell King (Oracle)
2023-05-31 7:14 ` Oleksij Rempel
2023-05-31 14:41 ` Russell King (Oracle)
2023-05-30 19:48 ` Andrew Lunn
2023-05-30 20:03 ` Florian Fainelli
2023-05-30 20:36 ` Russell King (Oracle)
2023-05-30 20:28 ` Russell King (Oracle)
2023-05-30 23:03 ` Florian Fainelli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230331005518.2134652-24-andrew@lunn.ch \
--to=andrew@lunn.ch \
--cc=f.fainelli@gmail.com \
--cc=hkallweit1@gmail.com \
--cc=linux@rempel-privat.de \
--cc=netdev@vger.kernel.org \
--cc=rmk+kernel@armlinux.org.uk \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).