From: Vladimir Oltean <olteanv@gmail.com>
To: Pawel Dembicki <paweldembicki@gmail.com>
Cc: netdev@vger.kernel.org, Linus Walleij <linus.walleij@linaro.org>,
Andrew Lunn <andrew@lunn.ch>,
Florian Fainelli <f.fainelli@gmail.com>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH net-next v2 3/7] net: dsa: vsc73xx: add port_stp_state_set function
Date: Sun, 25 Jun 2023 15:09:11 +0300 [thread overview]
Message-ID: <20230625120911.ws6eiywonoo5et7b@skbuf> (raw)
In-Reply-To: <20230625115343.1603330-3-paweldembicki@gmail.com>
On Sun, Jun 25, 2023 at 01:53:38PM +0200, Pawel Dembicki wrote:
> This isn't fully functional implementation of 802.1D, but
> port_stp_state_set is required for future tag8021q operations.
>
> This implementation handle properly all states, but vsc 73xx don't
handles
vsc73xx doesn't
> forward STP packets.
>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
> ---
> v2:
> - fix kdoc
>
> drivers/net/dsa/vitesse-vsc73xx-core.c | 51 +++++++++++++++++++++++---
> drivers/net/dsa/vitesse-vsc73xx.h | 2 +
> 2 files changed, 47 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/net/dsa/vitesse-vsc73xx-core.c b/drivers/net/dsa/vitesse-vsc73xx-core.c
> index 221672b9e17f..f123ce2ed244 100644
> --- a/drivers/net/dsa/vitesse-vsc73xx-core.c
> +++ b/drivers/net/dsa/vitesse-vsc73xx-core.c
> @@ -164,6 +164,10 @@
> #define VSC73XX_AGENCTRL 0xf0
> #define VSC73XX_CAPRST 0xff
>
> +#define VSC73XX_SRCMASKS_CPU_COPY BIT(27)
> +#define VSC73XX_SRCMASKS_MIRROR BIT(26)
> +#define VSC73XX_SRCMASKS_PORTS_MASK GENMASK(7, 0)
> +
> #define VSC73XX_MACACCESS_CPU_COPY BIT(14)
> #define VSC73XX_MACACCESS_FWD_KILL BIT(13)
> #define VSC73XX_MACACCESS_IGNORE_VLAN BIT(12)
> @@ -620,15 +624,17 @@ static int vsc73xx_setup(struct dsa_switch *ds)
> vsc73xx_write(vsc, VSC73XX_BLOCK_SYSTEM, 0, VSC73XX_GMIIDELAY,
> VSC73XX_GMIIDELAY_GMII0_GTXDELAY_2_0_NS |
> VSC73XX_GMIIDELAY_GMII0_RXDELAY_2_0_NS);
> - /* Enable reception of frames on all ports */
> - vsc73xx_write(vsc, VSC73XX_BLOCK_ANALYZER, 0, VSC73XX_RECVMASK,
> - 0x5f);
> /* IP multicast flood mask (table 144) */
> vsc73xx_write(vsc, VSC73XX_BLOCK_ANALYZER, 0, VSC73XX_IFLODMSK,
> 0xff);
>
> mdelay(50);
>
> + /*configure forward map to CPU <-> port only*/
> + for (i = 0; i < vsc->ds->num_ports; i++)
> + vsc->forward_map[i] = VSC73XX_SRCMASKS_PORTS_MASK & BIT(CPU_PORT);
> + vsc->forward_map[CPU_PORT] = VSC73XX_SRCMASKS_PORTS_MASK & ~BIT(CPU_PORT);
> +
> /* Release reset from the internal PHYs */
> vsc73xx_write(vsc, VSC73XX_BLOCK_SYSTEM, 0, VSC73XX_GLORESET,
> VSC73XX_GLORESET_PHY_RESET);
> @@ -871,9 +877,6 @@ static void vsc73xx_phylink_mac_link_up(struct dsa_switch *ds, int port,
> if (duplex == DUPLEX_FULL)
> val |= VSC73XX_MAC_CFG_FDX;
>
> - /* Enable port (forwarding) in the receieve mask */
> - vsc73xx_update_bits(vsc, VSC73XX_BLOCK_ANALYZER, 0,
> - VSC73XX_RECVMASK, BIT(port), BIT(port));
> vsc73xx_adjust_enable_port(vsc, port, val);
> }
>
> @@ -1040,6 +1043,41 @@ static int vsc73xx_get_max_mtu(struct dsa_switch *ds, int port)
> return 9600;
> }
>
> +static void vsc73xx_port_stp_state_set(struct dsa_switch *ds, int port,
> + u8 state)
> +{
> + struct vsc73xx *vsc = ds->priv;
Blank link after variable declarations; this affects comments too.
You can either put that comment above the function, or right above the
first "if" block (to me it makes more sense above the function).
> + /* FIXME: STP frames isn't forwarded at this moment. BPDU frames are
s/isn't/aren't/
> + * forwarded only from to PI/SI interface. For more info see chapter
s/from to/from and to/
> + * 2.7.1 (CPU Forwarding) in datasheet.
> + * This function is required for tag8021q operations.
> + */
> +
> + if (state == BR_STATE_BLOCKING)
state == BR_STATE_BLOCKING || state == BR_STATE_DISABLED
> + vsc73xx_update_bits(vsc, VSC73XX_BLOCK_ANALYZER, 0,
> + VSC73XX_RECVMASK, BIT(port), 0);
> + else
> + vsc73xx_update_bits(vsc, VSC73XX_BLOCK_ANALYZER, 0,
> + VSC73XX_RECVMASK, BIT(port), BIT(port));
> +
> + if (state == BR_STATE_LEARNING || state == BR_STATE_FORWARDING)
> + vsc73xx_update_bits(vsc, VSC73XX_BLOCK_ANALYZER, 0,
> + VSC73XX_LEARNMASK, BIT(port), BIT(port));
> + else
> + vsc73xx_update_bits(vsc, VSC73XX_BLOCK_ANALYZER, 0,
> + VSC73XX_LEARNMASK, BIT(port), 0);
> +
> + if (state == BR_STATE_FORWARDING)
> + vsc73xx_update_bits(vsc, VSC73XX_BLOCK_ANALYZER, 0,
> + VSC73XX_SRCMASKS + port,
> + VSC73XX_SRCMASKS_PORTS_MASK,
> + vsc->forward_map[port]);
> + else
> + vsc73xx_update_bits(vsc, VSC73XX_BLOCK_ANALYZER, 0,
> + VSC73XX_SRCMASKS + port,
> + VSC73XX_SRCMASKS_PORTS_MASK, 0);
> +}
> +
> static const struct dsa_switch_ops vsc73xx_ds_ops = {
> .get_tag_protocol = vsc73xx_get_tag_protocol,
> .setup = vsc73xx_setup,
> @@ -1056,6 +1094,7 @@ static const struct dsa_switch_ops vsc73xx_ds_ops = {
> .port_disable = vsc73xx_port_disable,
> .port_change_mtu = vsc73xx_change_mtu,
> .port_max_mtu = vsc73xx_get_max_mtu,
> + .port_stp_state_set = vsc73xx_port_stp_state_set,
> };
>
> static int vsc73xx_gpio_get(struct gpio_chip *chip, unsigned int offset)
> diff --git a/drivers/net/dsa/vitesse-vsc73xx.h b/drivers/net/dsa/vitesse-vsc73xx.h
> index 30b1f0a36566..c4d5398edeeb 100644
> --- a/drivers/net/dsa/vitesse-vsc73xx.h
> +++ b/drivers/net/dsa/vitesse-vsc73xx.h
> @@ -5,6 +5,7 @@
>
> /**
> * struct vsc73xx - VSC73xx state container
> + * @forward_map: Forward table cache
> */
> struct vsc73xx {
> struct device *dev;
> @@ -15,6 +16,7 @@ struct vsc73xx {
> u8 addr[ETH_ALEN];
> const struct vsc73xx_ops *ops;
> void *priv;
> + u8 forward_map[8];
Can we have this 8 and the one from the vsc->ds->num_ports assignment
consolidated into a single macro, VSC73XX_MAX_NUM_PORTS?
> };
>
> struct vsc73xx_ops {
> --
> 2.34.1
>
next prev parent reply other threads:[~2023-06-25 12:09 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-06-25 11:53 [PATCH net-next v2 1/7] net: dsa: vsc73xx: use read_poll_timeout instead delay loop Pawel Dembicki
2023-06-25 11:53 ` [PATCH net-next v2 2/7] net: dsa: vsc73xx: convert to PHYLINK Pawel Dembicki
2023-06-25 11:53 ` [PATCH net-next v2 3/7] net: dsa: vsc73xx: add port_stp_state_set function Pawel Dembicki
2023-06-25 12:09 ` Vladimir Oltean [this message]
2023-06-25 11:53 ` [PATCH net-next v2 4/7] net: dsa: vsc73xx: Add dsa tagging based on 8021q Pawel Dembicki
2023-06-25 12:42 ` Simon Horman
2023-06-26 10:37 ` Dan Carpenter
2023-06-25 12:47 ` Vladimir Oltean
2023-06-29 21:00 ` Paweł Dembicki
2023-07-03 16:16 ` Vladimir Oltean
2023-06-25 11:53 ` [PATCH net-next v2 5/7] net: dsa: vsc73xx: Add bridge support Pawel Dembicki
2023-06-25 11:53 ` [PATCH net-next v2 6/7] net: dsa: vsc73xx: Add vlan filtering Pawel Dembicki
2023-06-25 15:05 ` Vladimir Oltean
2023-06-29 20:18 ` Paweł Dembicki
2023-07-03 16:55 ` Vladimir Oltean
2023-06-25 11:53 ` [PATCH net-next v2 7/7] net: dsa: vsc73xx: fix MTU configuration Pawel Dembicki
2023-06-25 14:54 ` Vladimir Oltean
2023-06-28 20:04 ` Paweł Dembicki
2023-06-25 11:53 ` [PATCH net-next v2 0/7] net: dsa: vsc73xx: Make vsc73xx usable Pawel Dembicki
2023-06-25 14:42 ` Vladimir Oltean
2023-06-25 15:07 ` [PATCH net-next v2 1/7] net: dsa: vsc73xx: use read_poll_timeout instead delay loop Andrew Lunn
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230625120911.ws6eiywonoo5et7b@skbuf \
--to=olteanv@gmail.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=edumazet@google.com \
--cc=f.fainelli@gmail.com \
--cc=kuba@kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=paweldembicki@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).