* [PATCH v3 2/2] can: flexcan: remove the auto stop mode for IMX93
2023-07-26 11:24 [PATCH v3 1/2] arm64: dts: imx93: add the Flex-CAN stop mode by GPR haibo.chen
@ 2023-07-26 11:24 ` haibo.chen
2023-08-03 8:15 ` [PATCH v3 1/2] arm64: dts: imx93: add the Flex-CAN stop mode by GPR Marc Kleine-Budde
1 sibling, 0 replies; 3+ messages in thread
From: haibo.chen @ 2023-07-26 11:24 UTC (permalink / raw)
To: robh+dt, krzysztof.kozlowski+dt, conor+dt, shawnguo, s.hauer, wg,
mkl
Cc: kernel, linux-imx, davem, edumazet, kuba, pabeni, haibo.chen,
devicetree, linux-can, netdev
From: Haibo Chen <haibo.chen@nxp.com>
IMX93 A0 chip involve the internal q-channel handshake in LPCG and
CCM to automatically handle the Flex-CAN IPG STOP signal. Only after
FLEX-CAN enter stop mode then can support the self-wakeup feature.
But meet issue when do the continue system PM stress test. When config
the CAN as wakeup source, the first time after system suspend, any data
on CAN bus can wakeup the system, this is as expect. But the second time
when system suspend, data on CAN bus can't wakeup the system. If continue
this test, we find in odd time system enter suspend, CAN can wakeup the
system, but in even number system enter suspend, CAN can't wakeup the
system. IC find a bug in the auto stop mode logic, and can't fix it easily.
So for the new imx93 A1, IC drop the auto stop mode and involve the
GPR to support stop mode (used before). IC define a bit in GPR which can
trigger the IPG STOP signal to Flex-CAN, let it go into stop mode.
And NXP claim to drop IMX93 A0, and only support IMX93 A1. So this patch
remove the auto stop mode, and add flag FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR
to imx93.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
---
drivers/net/can/flexcan/flexcan-core.c | 46 ++++++++------------------
drivers/net/can/flexcan/flexcan.h | 2 --
2 files changed, 13 insertions(+), 35 deletions(-)
diff --git a/drivers/net/can/flexcan/flexcan-core.c b/drivers/net/can/flexcan/flexcan-core.c
index ff0fc18baf13..d8be69f4a0c3 100644
--- a/drivers/net/can/flexcan/flexcan-core.c
+++ b/drivers/net/can/flexcan/flexcan-core.c
@@ -348,7 +348,7 @@ static struct flexcan_devtype_data fsl_imx8mp_devtype_data = {
static struct flexcan_devtype_data fsl_imx93_devtype_data = {
.quirks = FLEXCAN_QUIRK_DISABLE_RXFG | FLEXCAN_QUIRK_ENABLE_EACEN_RRS |
FLEXCAN_QUIRK_DISABLE_MECR | FLEXCAN_QUIRK_USE_RX_MAILBOX |
- FLEXCAN_QUIRK_BROKEN_PERR_STATE | FLEXCAN_QUIRK_AUTO_STOP_MODE |
+ FLEXCAN_QUIRK_BROKEN_PERR_STATE | FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR |
FLEXCAN_QUIRK_SUPPORT_FD | FLEXCAN_QUIRK_SUPPORT_ECC |
FLEXCAN_QUIRK_SUPPORT_RX_MAILBOX |
FLEXCAN_QUIRK_SUPPORT_RX_MAILBOX_RTR,
@@ -544,11 +544,6 @@ static inline int flexcan_enter_stop_mode(struct flexcan_priv *priv)
} else if (priv->devtype_data.quirks & FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR) {
regmap_update_bits(priv->stm.gpr, priv->stm.req_gpr,
1 << priv->stm.req_bit, 1 << priv->stm.req_bit);
- } else if (priv->devtype_data.quirks & FLEXCAN_QUIRK_AUTO_STOP_MODE) {
- /* For the auto stop mode, software do nothing, hardware will cover
- * all the operation automatically after system go into low power mode.
- */
- return 0;
}
return flexcan_low_power_enter_ack(priv);
@@ -574,12 +569,6 @@ static inline int flexcan_exit_stop_mode(struct flexcan_priv *priv)
reg_mcr &= ~FLEXCAN_MCR_SLF_WAK;
priv->write(reg_mcr, ®s->mcr);
- /* For the auto stop mode, hardware will exist stop mode
- * automatically after system go out of low power mode.
- */
- if (priv->devtype_data.quirks & FLEXCAN_QUIRK_AUTO_STOP_MODE)
- return 0;
-
return flexcan_low_power_exit_ack(priv);
}
@@ -1994,13 +1983,18 @@ static int flexcan_setup_stop_mode(struct platform_device *pdev)
ret = flexcan_setup_stop_mode_scfw(pdev);
else if (priv->devtype_data.quirks & FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR)
ret = flexcan_setup_stop_mode_gpr(pdev);
- else if (priv->devtype_data.quirks & FLEXCAN_QUIRK_AUTO_STOP_MODE)
- ret = 0;
else
/* return 0 directly if doesn't support stop mode feature */
return 0;
- if (ret)
+ /* If ret is -EINVAL, this means SoC claim to support stop mode, but
+ * dts file lack the stop mode property definition. For this case,
+ * directly return 0, this will skip the wakeup capable setting and
+ * will not block the driver probe.
+ */
+ if (ret == -EINVAL)
+ return 0;
+ else if (ret)
return ret;
device_set_wakeup_capable(&pdev->dev, true);
@@ -2320,16 +2314,8 @@ static int __maybe_unused flexcan_noirq_suspend(struct device *device)
if (netif_running(dev)) {
int err;
- if (device_may_wakeup(device)) {
+ if (device_may_wakeup(device))
flexcan_enable_wakeup_irq(priv, true);
- /* For auto stop mode, need to keep the clock on before
- * system go into low power mode. After system go into
- * low power mode, hardware will config the flexcan into
- * stop mode, and gate off the clock automatically.
- */
- if (priv->devtype_data.quirks & FLEXCAN_QUIRK_AUTO_STOP_MODE)
- return 0;
- }
err = pm_runtime_force_suspend(device);
if (err)
@@ -2347,15 +2333,9 @@ static int __maybe_unused flexcan_noirq_resume(struct device *device)
if (netif_running(dev)) {
int err;
- /* For the wakeup in auto stop mode, no need to gate on the
- * clock here, hardware will do this automatically.
- */
- if (!(device_may_wakeup(device) &&
- priv->devtype_data.quirks & FLEXCAN_QUIRK_AUTO_STOP_MODE)) {
- err = pm_runtime_force_resume(device);
- if (err)
- return err;
- }
+ err = pm_runtime_force_resume(device);
+ if (err)
+ return err;
if (device_may_wakeup(device))
flexcan_enable_wakeup_irq(priv, false);
diff --git a/drivers/net/can/flexcan/flexcan.h b/drivers/net/can/flexcan/flexcan.h
index 91402977780b..025c3417031f 100644
--- a/drivers/net/can/flexcan/flexcan.h
+++ b/drivers/net/can/flexcan/flexcan.h
@@ -68,8 +68,6 @@
#define FLEXCAN_QUIRK_SUPPORT_RX_MAILBOX_RTR BIT(15)
/* Device supports RX via FIFO */
#define FLEXCAN_QUIRK_SUPPORT_RX_FIFO BIT(16)
-/* auto enter stop mode to support wakeup */
-#define FLEXCAN_QUIRK_AUTO_STOP_MODE BIT(17)
struct flexcan_devtype_data {
u32 quirks; /* quirks needed for different IP cores */
--
2.34.1
^ permalink raw reply related [flat|nested] 3+ messages in thread* Re: [PATCH v3 1/2] arm64: dts: imx93: add the Flex-CAN stop mode by GPR
2023-07-26 11:24 [PATCH v3 1/2] arm64: dts: imx93: add the Flex-CAN stop mode by GPR haibo.chen
2023-07-26 11:24 ` [PATCH v3 2/2] can: flexcan: remove the auto stop mode for IMX93 haibo.chen
@ 2023-08-03 8:15 ` Marc Kleine-Budde
1 sibling, 0 replies; 3+ messages in thread
From: Marc Kleine-Budde @ 2023-08-03 8:15 UTC (permalink / raw)
To: haibo.chen
Cc: robh+dt, krzysztof.kozlowski+dt, conor+dt, shawnguo, s.hauer, wg,
kernel, linux-imx, davem, edumazet, kuba, pabeni, devicetree,
linux-can, netdev
[-- Attachment #1: Type: text/plain, Size: 993 bytes --]
On 26.07.2023 19:24:57, haibo.chen@nxp.com wrote:
> From: Haibo Chen <haibo.chen@nxp.com>
>
> imx93 A0 chip use the internal q-channel handshake signal in LPCG
> and CCM to automatically handle the Flex-CAN stop mode. But this
> method meet issue when do the system PM stress test. IC can't fix
> it easily. So in the new imx93 A1 chip, IC drop this method, and
> involve back the old way，use the GPR method to trigger the Flex-CAN
> stop mode signal. Now NXP claim to drop imx93 A0, and only support
> imx93 A1. So here add the stop mode through GPR.
>
> This patch also fix a typo for aonmix_ns_gpr.
>
> Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Added both to linux-can/testing.
Thanks,
Marc
--
Pengutronix e.K. | Marc Kleine-Budde |
Embedded Linux | https://www.pengutronix.de |
Vertretung Nürnberg | Phone: +49-5121-206917-129 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-9 |
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply [flat|nested] 3+ messages in thread