[PATCH AUTOSEL 5.15 01/15] usb: aqc111: check packet for fixup for true limit

[PATCH AUTOSEL 5.15 01/15] usb: aqc111: check packet for fixup for true limit

[Sasha Levin]

From: Oliver Neukum <oneukum@suse.com>

[ Upstream commit ccab434e674ca95d483788b1895a70c21b7f016a ]

If a device sends a packet that is inbetween 0
and sizeof(u64) the value passed to skb_trim()
as length will wrap around ending up as some very
large value.

The driver will then proceed to parse the header
located at that position, which will either oops or
process some random value.

The fix is to check against sizeof(u64) rather than
0, which the driver currently does. The issue exists
since the introduction of the driver.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/aqc111.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/net/usb/aqc111.c b/drivers/net/usb/aqc111.c
index e8d49886d6953..bc5e3f45c499e 100644
--- a/drivers/net/usb/aqc111.c
+++ b/drivers/net/usb/aqc111.c
@@ -1079,17 +1079,17 @@ static int aqc111_rx_fixup(struct usbnet *dev, struct sk_buff *skb)
 	u16 pkt_count = 0;
 	u64 desc_hdr = 0;
 	u16 vlan_tag = 0;
-	u32 skb_len = 0;
+	u32 skb_len;
 
 	if (!skb)
 		goto err;
 
-	if (skb->len == 0)
+	skb_len = skb->len;
+	if (skb_len < sizeof(desc_hdr))
 		goto err;
 
-	skb_len = skb->len;
 	/* RX Descriptor Header */
-	skb_trim(skb, skb->len - sizeof(desc_hdr));
+	skb_trim(skb, skb_len - sizeof(desc_hdr));
 	desc_hdr = le64_to_cpup((u64 *)skb_tail_pointer(skb));
 
 	/* Check these packets */
-- 
2.42.0

[PATCH AUTOSEL 5.15 02/15] stmmac: dwmac-loongson: Add architecture dependency

[Sasha Levin]

From: Jean Delvare <jdelvare@suse.de>

[ Upstream commit 7fbd5fc2b35a8f559a6b380dfa9bcd964a758186 ]

Only present the DWMAC_LOONGSON option on architectures where it can
actually be used.

This follows the same logic as the DWMAC_INTEL option.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index 929cfc22cd0cf..d19844be9fe50 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -253,7 +253,7 @@ config DWMAC_INTEL
 config DWMAC_LOONGSON
 	tristate "Loongson PCI DWMAC support"
 	default MACH_LOONGSON64
-	depends on STMMAC_ETH && PCI
+	depends on (MACH_LOONGSON64 || COMPILE_TEST) && STMMAC_ETH && PCI
 	depends on COMMON_CLK
 	help
 	  This selects the LOONGSON PCI bus support for the stmmac driver,
-- 
2.42.0

[PATCH AUTOSEL 5.15 15/15] net: usb: qmi_wwan: claim interface 4 for ZTE MF290

[Sasha Levin]

From: Lech Perczak <lech.perczak@gmail.com>

[ Upstream commit 99360d9620f09fb8bc15548d855011bbb198c680 ]

Interface 4 is used by for QMI interface in stock firmware of MF28D, the
router which uses MF290 modem. Rebind it to qmi_wwan after freeing it up
from option driver.
The proper configuration is:

Interface mapping is:
0: QCDM, 1: (unknown), 2: AT (PCUI), 2: AT (Modem), 4: QMI

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=0189 Rev= 0.00
S:  Manufacturer=ZTE, Incorporated
S:  Product=ZTE LTE Technologies MSM
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms

Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://lore.kernel.org/r/20231117231918.100278-3-lech.perczak@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/usb/qmi_wwan.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/usb/qmi_wwan.c b/drivers/net/usb/qmi_wwan.c
index 5c516bf4d3a5f..846ace9830d3b 100644
--- a/drivers/net/usb/qmi_wwan.c
+++ b/drivers/net/usb/qmi_wwan.c
@@ -1286,6 +1286,7 @@ static const struct usb_device_id products[] = {
 	{QMI_FIXED_INTF(0x19d2, 0x0168, 4)},
 	{QMI_FIXED_INTF(0x19d2, 0x0176, 3)},
 	{QMI_FIXED_INTF(0x19d2, 0x0178, 3)},
+	{QMI_FIXED_INTF(0x19d2, 0x0189, 4)},    /* ZTE MF290 */
 	{QMI_FIXED_INTF(0x19d2, 0x0191, 4)},	/* ZTE EuFi890 */
 	{QMI_FIXED_INTF(0x19d2, 0x0199, 1)},	/* ZTE MF820S */
 	{QMI_FIXED_INTF(0x19d2, 0x0200, 1)},
-- 
2.42.0