From: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
To: Emil Renner Berthing <kernel@esmil.dk>,
Conor Dooley <conor@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Paul Walmsley <paul.walmsley@sifive.com>,
Palmer Dabbelt <palmer@dabbelt.com>,
Albert Ou <aou@eecs.berkeley.edu>,
Richard Cochran <richardcochran@gmail.com>,
Andrew Lunn <andrew@lunn.ch>,
Jacob Keller <jacob.e.keller@intel.com>
Cc: linux-riscv@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, netdev@vger.kernel.org,
kernel@collabora.com,
Emil Renner Berthing <emil.renner.berthing@canonical.com>
Subject: [PATCH v6 1/4] riscv: dts: starfive: jh7100: Add sysmain and gmac DT nodes
Date: Wed, 20 Dec 2023 23:17:39 +0200 [thread overview]
Message-ID: <20231220211743.2490518-2-cristian.ciocaltea@collabora.com> (raw)
In-Reply-To: <20231220211743.2490518-1-cristian.ciocaltea@collabora.com>
Provide the sysmain and gmac DT nodes supporting the DWMAC found on the
StarFive JH7100 SoC.
Co-developed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
---
arch/riscv/boot/dts/starfive/jh7100.dtsi | 36 ++++++++++++++++++++++++
1 file changed, 36 insertions(+)
diff --git a/arch/riscv/boot/dts/starfive/jh7100.dtsi b/arch/riscv/boot/dts/starfive/jh7100.dtsi
index c216aaecac53..2ebdebe6a81c 100644
--- a/arch/riscv/boot/dts/starfive/jh7100.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7100.dtsi
@@ -204,6 +204,37 @@ sdio1: mmc@10010000 {
status = "disabled";
};
+ gmac: ethernet@10020000 {
+ compatible = "starfive,jh7100-dwmac", "snps,dwmac";
+ reg = <0x0 0x10020000 0x0 0x10000>;
+ clocks = <&clkgen JH7100_CLK_GMAC_ROOT_DIV>,
+ <&clkgen JH7100_CLK_GMAC_AHB>,
+ <&clkgen JH7100_CLK_GMAC_PTP_REF>,
+ <&clkgen JH7100_CLK_GMAC_TX_INV>,
+ <&clkgen JH7100_CLK_GMAC_GTX>;
+ clock-names = "stmmaceth", "pclk", "ptp_ref", "tx", "gtx";
+ resets = <&rstgen JH7100_RSTN_GMAC_AHB>;
+ reset-names = "ahb";
+ interrupts = <6>, <7>;
+ interrupt-names = "macirq", "eth_wake_irq";
+ max-frame-size = <9000>;
+ snps,multicast-filter-bins = <32>;
+ snps,perfect-filter-entries = <128>;
+ starfive,syscon = <&sysmain 0x70 0>;
+ rx-fifo-depth = <32768>;
+ tx-fifo-depth = <16384>;
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,fixed-burst;
+ snps,force_thresh_dma_mode;
+ status = "disabled";
+
+ stmmac_axi_setup: stmmac-axi-config {
+ snps,wr_osr_lmt = <16>;
+ snps,rd_osr_lmt = <16>;
+ snps,blen = <256 128 64 32 0 0 0>;
+ };
+ };
+
clkgen: clock-controller@11800000 {
compatible = "starfive,jh7100-clkgen";
reg = <0x0 0x11800000 0x0 0x10000>;
@@ -218,6 +249,11 @@ rstgen: reset-controller@11840000 {
#reset-cells = <1>;
};
+ sysmain: syscon@11850000 {
+ compatible = "starfive,jh7100-sysmain", "syscon";
+ reg = <0x0 0x11850000 0x0 0x10000>;
+ };
+
i2c0: i2c@118b0000 {
compatible = "snps,designware-i2c";
reg = <0x0 0x118b0000 0x0 0x10000>;
--
2.43.0
next prev parent reply other threads:[~2023-12-20 21:17 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-12-20 21:17 [PATCH v6 0/4] Enable networking support for StarFive JH7100 SoC Cristian Ciocaltea
2023-12-20 21:17 ` Cristian Ciocaltea [this message]
2023-12-20 21:17 ` [PATCH v6 2/4] riscv: dts: starfive: jh7100-common: Setup pinmux and enable gmac Cristian Ciocaltea
2023-12-20 21:17 ` [PATCH v6 3/4] riscv: dts: starfive: visionfive-v1: Setup ethernet phy Cristian Ciocaltea
2023-12-20 21:17 ` [PATCH v6 4/4] riscv: dts: starfive: beaglev-starlight: Setup phy reset gpio Cristian Ciocaltea
2023-12-26 20:38 ` [PATCH v6 0/4] Enable networking support for StarFive JH7100 SoC Emil Renner Berthing
2024-01-10 13:57 ` Conor Dooley
2024-01-10 16:17 ` Cristian Ciocaltea
2024-01-31 11:29 ` Cristian Ciocaltea
2024-01-31 12:25 ` Conor Dooley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20231220211743.2490518-2-cristian.ciocaltea@collabora.com \
--to=cristian.ciocaltea@collabora.com \
--cc=andrew@lunn.ch \
--cc=aou@eecs.berkeley.edu \
--cc=conor@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=emil.renner.berthing@canonical.com \
--cc=jacob.e.keller@intel.com \
--cc=kernel@collabora.com \
--cc=kernel@esmil.dk \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=netdev@vger.kernel.org \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=richardcochran@gmail.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox