[PATCH net-next v3 07/10] arm64: dts: allwinner: a527: cubie-a5e: Enable second Ethernet port

[Chen-Yu Tsai <wens@kernel.org>]

From: Chen-Yu Tsai <wens@csie.org>

On the Radxa Cubie A5E board, the second Ethernet controller, aka the
GMAC200, is connected to a second external Maxio MAE0621A PHY. The PHY
uses an external 25MHz crystal, and has the SoC's PJ16 pin connected to
its reset pin.

Enable the second Ethernet port. Also fix up the label for the existing
external PHY connected to the first Ethernet port. An enable delay for the
PHY supply regulator is added to make sure the PHY's internal regulators
are fully powered and the PHY is operational.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---

Changes since v1:
- Switch to generic (tx|rx)-internal-delay-ps properties
- Add PHY regulator delay
---
 .../dts/allwinner/sun55i-a527-cubie-a5e.dts   | 28 +++++++++++++++++--
 1 file changed, 26 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts b/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
index d4cee2222104..e96a419faf21 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
+++ b/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
@@ -14,6 +14,7 @@ / {
 
 	aliases {
 		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
 		serial0 = &uart0;
 	};
 
@@ -76,7 +77,7 @@ &ehci1 {
 
 &gmac0 {
 	phy-mode = "rgmii-id";
-	phy-handle = <&ext_rgmii_phy>;
+	phy-handle = <&ext_rgmii0_phy>;
 	phy-supply = <&reg_cldo3>;
 
 	allwinner,tx-delay-ps = <300>;
@@ -85,13 +86,24 @@ &gmac0 {
 	status = "okay";
 };
 
+&gmac1 {
+	phy-mode = "rgmii-id";
+	phy-handle = <&ext_rgmii1_phy>;
+	phy-supply = <&reg_cldo4>;
+
+	tx-internal-delay-ps = <300>;
+	rx-internal-delay-ps = <400>;
+
+	status = "okay";
+};
+
 &gpu {
 	mali-supply = <&reg_dcdc2>;
 	status = "okay";
 };
 
 &mdio0 {
-	ext_rgmii_phy: ethernet-phy@1 {
+	ext_rgmii0_phy: ethernet-phy@1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		reset-gpios = <&pio 7 8 GPIO_ACTIVE_LOW>; /* PH8 */
@@ -100,6 +112,16 @@ ext_rgmii_phy: ethernet-phy@1 {
 	};
 };
 
+&mdio1 {
+	ext_rgmii1_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		reset-gpios = <&pio 9 16 GPIO_ACTIVE_LOW>; /* PJ16 */
+		reset-assert-us = <10000>;
+		reset-deassert-us = <150000>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_cldo3>;
 	cd-gpios = <&pio 5 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PF6 */
@@ -240,6 +262,8 @@ reg_cldo4: cldo4 {
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-name = "vcc-pj-phy";
+				/* enough time for the PHY to fully power on */
+				regulator-enable-ramp-delay = <150000>;
 			};
 
 			reg_cpusldo: cpusldo {
-- 
2.39.5