[PATCH net-next v7 0/6] net: stmmac: Add support for Allwinner A523 GMAC200

[PATCH net-next v7 0/6] net: stmmac: Add support for Allwinner A523 GMAC200

[Chen-Yu Tsai]

From: Chen-Yu Tsai <wens@csie.org>

Hi everyone,

This is v7 of my Allwinner A523 GMAC200 support series. This is based on
next-20250922.

Changes since v6:
- Collected acks for DT binding patch
- Rebased onto next-20250922

Changes since v5:
- Use plat->phy_interface instead of plat->mac_interface (Russell)
- Link to v5
  https://lore.kernel.org/all/20250911174032.3147192-1-wens@kernel.org/

Changes since v4:
- Moved clock-names list to main schema in DT binding (Rob)
- Dropped 4 patches that are already merged
- Link to v4
  https://lore.kernel.org/all/20250908181059.1785605-1-wens@kernel.org/

Changes since v3:
- driver
  - Fixed printf format specifier warning
- Link to v3
  https://lore.kernel.org/all/20250906041333.642483-1-wens@kernel.org/

Changes since v2:
- DT binding
  - Added "select" to avoid matching against all dwmac entries
- driver
  - Include "ps" unit in "... must be multiple of ..." error message
  - Use FIELD_FIT to check if delay value is in range and FIELD_MAX to get
    the maximum value
  - Reword error message for delay value exceeding maximum
  - Drop MASK_TO_VAL
- Link to v2:
  https://lore.kernel.org/all/20250813145540.2577789-1-wens@kernel.org/

Changes since v1:
- Dropped RFT tag
- Switched to generic (tx|rx)-internal-delay-ps 
- dwmac-sun55i driver bits
  - Changed dev_err() + return to dev_err_probe()
  - Added check of return value from syscon regmap write
  - Changed driver name to match file name
- sram driver bits
  - Fixed check on return value
  - Expanded commit message
- dtsi
  - Fixed typo in tx-queues-config
- cubie a5e
  - Add PHY regulator delay
- Link to v1:
  https://lore.kernel.org/all/20250701165756.258356-1-wens@kernel.org/

This series adds support for the second Ethernet controller found on the
Allwinner A523 SoC family. This controller, dubbed GMAC200, is a DWMAC4
core with an integration layer around it. The integration layer is
similar to older Allwinner generations, but with an extra memory bus
gate and separate power domain.

Patch 1 adds a new compatible string combo to the existing Allwinner
EMAC binding.

Patch 2 adds a new driver for this core and integration combo.

Patch 3 adds a device node and pinmux settings for the GMAC200.

Patches 4, 5, and 6 enable the GMAC200 on three boards. I only tested
the Orangepi 4A and Radxa Cubie A5E.


Please have a look and help test on the Avaota A1. I don't expect
any issues there though, since the PHY is always on, unlike on the
Cubie A5E.

Patches 1 and 2 should go through net-next, and I will take all the
other patches through the sunxi tree. Hopefully we can get this merged
for v6.18.


Thanks
ChenYu

Chen-Yu Tsai (6):
  dt-bindings: net: sun8i-emac: Add A523 GMAC200 compatible
  net: stmmac: Add support for Allwinner A523 GMAC200
  arm64: dts: allwinner: a523: Add GMAC200 ethernet controller
  arm64: dts: allwinner: a527: cubie-a5e: Enable second Ethernet port
  arm64: dts: allwinner: t527: avaota-a1: enable second Ethernet port
  arm64: dts: allwinner: t527: orangepi-4a: Enable Ethernet port

 .../net/allwinner,sun8i-a83t-emac.yaml        |  95 ++++++++++-
 .../arm64/boot/dts/allwinner/sun55i-a523.dtsi |  55 ++++++
 .../dts/allwinner/sun55i-a527-cubie-a5e.dts   |  28 ++-
 .../dts/allwinner/sun55i-t527-avaota-a1.dts   |  26 ++-
 .../dts/allwinner/sun55i-t527-orangepi-4a.dts |  23 +++
 drivers/net/ethernet/stmicro/stmmac/Kconfig   |  12 ++
 drivers/net/ethernet/stmicro/stmmac/Makefile  |   1 +
 .../ethernet/stmicro/stmmac/dwmac-sun55i.c    | 159 ++++++++++++++++++
 8 files changed, 393 insertions(+), 6 deletions(-)
 create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-sun55i.c

-- 
2.47.3

[PATCH net-next v7 1/6] dt-bindings: net: sun8i-emac: Add A523 GMAC200 compatible

[Chen-Yu Tsai]

From: Chen-Yu Tsai <wens@csie.org>

The Allwinner A523 SoC family has a second Ethernet controller, called
the GMAC200 in the BSP and T527 datasheet, and referred to as GMAC1 for
numbering. This controller, according to BSP sources, is fully
compatible with a slightly newer version of the Synopsys DWMAC core.
The glue layer around the controller is the same as found around older
DWMAC cores on Allwinner SoCs. The only slight difference is that since
this is the second controller on the SoC, the register for the clock
delay controls is at a different offset. Last, the integration includes
a dedicated clock gate for the memory bus and the whole thing is put in
a separately controllable power domain.

Add a compatible string entry for it, and work in the requirements for
a second clock and a power domain.

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v6:
- Collected tags
Changes since v4:
- Move clock-names list to main schema (Rob)
Changes since v2:
- Added "select" to avoid matching against all dwmac entries
Changes since v1:
- Switch to generic (tx|rx)-internal-delay-ps properties
---
 .../net/allwinner,sun8i-a83t-emac.yaml        | 95 ++++++++++++++++++-
 1 file changed, 93 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml b/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
index 2ac709a4c472..fc62fb2a68ac 100644
--- a/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
+++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
@@ -10,6 +10,21 @@ maintainers:
   - Chen-Yu Tsai <wens@csie.org>
   - Maxime Ripard <mripard@kernel.org>
 
+# We need a select here so we don't match all nodes with 'snps,dwmac'
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - allwinner,sun8i-a83t-emac
+          - allwinner,sun8i-h3-emac
+          - allwinner,sun8i-r40-gmac
+          - allwinner,sun8i-v3s-emac
+          - allwinner,sun50i-a64-emac
+          - allwinner,sun55i-a523-gmac200
+  required:
+    - compatible
+
 properties:
   compatible:
     oneOf:
@@ -26,6 +41,9 @@ properties:
               - allwinner,sun50i-h616-emac0
               - allwinner,sun55i-a523-gmac0
           - const: allwinner,sun50i-a64-emac
+      - items:
+          - const: allwinner,sun55i-a523-gmac200
+          - const: snps,dwmac-4.20a
 
   reg:
     maxItems: 1
@@ -37,14 +55,21 @@ properties:
     const: macirq
 
   clocks:
-    maxItems: 1
+    minItems: 1
+    maxItems: 2
 
   clock-names:
-    const: stmmaceth
+    minItems: 1
+    items:
+      - const: stmmaceth
+      - const: mbus
 
   phy-supply:
     description: PHY regulator
 
+  power-domains:
+    maxItems: 1
+
   syscon:
     $ref: /schemas/types.yaml#/definitions/phandle
     description:
@@ -191,6 +216,42 @@ allOf:
             - mdio-parent-bus
             - mdio@1
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: allwinner,sun55i-a523-gmac200
+    then:
+      properties:
+        clocks:
+          minItems: 2
+        clock-names:
+          minItems: 2
+        tx-internal-delay-ps:
+          default: 0
+          minimum: 0
+          maximum: 700
+          multipleOf: 100
+          description:
+            External RGMII PHY TX clock delay chain value in ps.
+        rx-internal-delay-ps:
+          default: 0
+          minimum: 0
+          maximum: 3100
+          multipleOf: 100
+          description:
+            External RGMII PHY TX clock delay chain value in ps.
+      required:
+        - power-domains
+    else:
+      properties:
+        clocks:
+          maxItems: 1
+        clock-names:
+          maxItems: 1
+        power-domains: false
+
+
 unevaluatedProperties: false
 
 examples:
@@ -323,4 +384,34 @@ examples:
         };
     };
 
+  - |
+    ethernet@4510000 {
+        compatible = "allwinner,sun55i-a523-gmac200",
+                     "snps,dwmac-4.20a";
+        reg = <0x04510000 0x10000>;
+        clocks = <&ccu 117>, <&ccu 79>;
+        clock-names = "stmmaceth", "mbus";
+        resets = <&ccu 43>;
+        reset-names = "stmmaceth";
+        interrupts = <0 47 4>;
+        interrupt-names = "macirq";
+        pinctrl-names = "default";
+        pinctrl-0 = <&rgmii1_pins>;
+        power-domains = <&pck600 4>;
+        syscon = <&syscon>;
+        phy-handle = <&ext_rgmii_phy_1>;
+        phy-mode = "rgmii-id";
+        snps,fixed-burst;
+        snps,axi-config = <&gmac1_stmmac_axi_setup>;
+
+        mdio {
+            compatible = "snps,dwmac-mdio";
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            ext_rgmii_phy_1: ethernet-phy@1 {
+                reg = <1>;
+            };
+        };
+    };
 ...
-- 
2.47.3

[PATCH net-next v7 2/6] net: stmmac: Add support for Allwinner A523 GMAC200

[Chen-Yu Tsai]

From: Chen-Yu Tsai <wens@csie.org>

The Allwinner A523 SoC family has a second Ethernet controller, called
the GMAC200 in the BSP and T527 datasheet, and referred to as GMAC1 for
numbering. This controller, according to BSP sources, is fully
compatible with a slightly newer version of the Synopsys DWMAC core.
The glue layer around the controller is the same as found around older
DWMAC cores on Allwinner SoCs. The only slight difference is that since
this is the second controller on the SoC, the register for the clock
delay controls is at a different offset. Last, the integration includes
a dedicated clock gate for the memory bus and the whole thing is put in
a separately controllable power domain.

Add a new driver for this hardware supporting the integration layer.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v5:
- Use plat->phy_interface instead of plat->mac_interface (Russell)

Changes since v3:
- Fixed printf format specifier warning

Changes since v2 (all suggested by Russell King):
- Include "ps" unit in "... must be multiple of ..." error message
- Use FIELD_FIT to check if delay value is in range and FIELD_MAX to get
  the maximum value
- Reword error message for delay value exceeding maximum
- Drop MASK_TO_VAL

Changes since v1:
- Switch to generic (tx|rx)-internal-delay-ps properties
- Change dev_err() + return to dev_err_probe()
- Check return value from syscon regmap write
- Change driver name to match file name
---
 drivers/net/ethernet/stmicro/stmmac/Kconfig   |  12 ++
 drivers/net/ethernet/stmicro/stmmac/Makefile  |   1 +
 .../ethernet/stmicro/stmmac/dwmac-sun55i.c    | 159 ++++++++++++++++++
 3 files changed, 172 insertions(+)
 create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-sun55i.c

diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index 91d9a14362bf..9507131875b2 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -265,6 +265,18 @@ config DWMAC_SUN8I
 	  stmmac device driver. This driver is used for H3/A83T/A64
 	  EMAC ethernet controller.
 
+config DWMAC_SUN55I
+	tristate "Allwinner sun55i GMAC200 support"
+	default ARCH_SUNXI
+	depends on OF && (ARCH_SUNXI || COMPILE_TEST)
+	select MDIO_BUS_MUX
+	help
+	  Support for Allwinner A523/T527 GMAC200 ethernet controllers.
+
+	  This selects Allwinner SoC glue layer support for the
+	  stmmac device driver. This driver is used for A523/T527
+	  GMAC200 ethernet controller.
+
 config DWMAC_THEAD
 	tristate "T-HEAD dwmac support"
 	depends on OF && (ARCH_THEAD || COMPILE_TEST)
diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
index b591d93f8503..51e068e26ce4 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Makefile
+++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -31,6 +31,7 @@ obj-$(CONFIG_DWMAC_STI)		+= dwmac-sti.o
 obj-$(CONFIG_DWMAC_STM32)	+= dwmac-stm32.o
 obj-$(CONFIG_DWMAC_SUNXI)	+= dwmac-sunxi.o
 obj-$(CONFIG_DWMAC_SUN8I)	+= dwmac-sun8i.o
+obj-$(CONFIG_DWMAC_SUN55I)	+= dwmac-sun55i.o
 obj-$(CONFIG_DWMAC_THEAD)	+= dwmac-thead.o
 obj-$(CONFIG_DWMAC_DWC_QOS_ETH)	+= dwmac-dwc-qos-eth.o
 obj-$(CONFIG_DWMAC_INTEL_PLAT)	+= dwmac-intel-plat.o
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun55i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun55i.c
new file mode 100644
index 000000000000..862df173d963
--- /dev/null
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun55i.c
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * dwmac-sun55i.c - Allwinner sun55i GMAC200 specific glue layer
+ *
+ * Copyright (C) 2025 Chen-Yu Tsai <wens@csie.org>
+ *
+ * syscon parts taken from dwmac-sun8i.c, which is
+ *
+ * Copyright (C) 2017 Corentin Labbe <clabbe.montjoie@gmail.com>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/stmmac.h>
+
+#include "stmmac.h"
+#include "stmmac_platform.h"
+
+#define SYSCON_REG		0x34
+
+/* RMII specific bits */
+#define SYSCON_RMII_EN		BIT(13) /* 1: enable RMII (overrides EPIT) */
+/* Generic system control EMAC_CLK bits */
+#define SYSCON_ETXDC_MASK		GENMASK(12, 10)
+#define SYSCON_ERXDC_MASK		GENMASK(9, 5)
+/* EMAC PHY Interface Type */
+#define SYSCON_EPIT			BIT(2) /* 1: RGMII, 0: MII */
+#define SYSCON_ETCS_MASK		GENMASK(1, 0)
+#define SYSCON_ETCS_MII		0x0
+#define SYSCON_ETCS_EXT_GMII	0x1
+#define SYSCON_ETCS_INT_GMII	0x2
+
+static int sun55i_gmac200_set_syscon(struct device *dev,
+				     struct plat_stmmacenet_data *plat)
+{
+	struct device_node *node = dev->of_node;
+	struct regmap *regmap;
+	u32 val, reg = 0;
+	int ret;
+
+	regmap = syscon_regmap_lookup_by_phandle(node, "syscon");
+	if (IS_ERR(regmap))
+		return dev_err_probe(dev, PTR_ERR(regmap), "Unable to map syscon\n");
+
+	if (!of_property_read_u32(node, "tx-internal-delay-ps", &val)) {
+		if (val % 100)
+			return dev_err_probe(dev, -EINVAL,
+					     "tx-delay must be a multiple of 100ps\n");
+		val /= 100;
+		dev_dbg(dev, "set tx-delay to %x\n", val);
+		if (!FIELD_FIT(SYSCON_ETXDC_MASK, val))
+			return dev_err_probe(dev, -EINVAL,
+					     "TX clock delay exceeds maximum (%u00ps > %lu00ps)\n",
+					     val, FIELD_MAX(SYSCON_ETXDC_MASK));
+
+		reg |= FIELD_PREP(SYSCON_ETXDC_MASK, val);
+	}
+
+	if (!of_property_read_u32(node, "rx-internal-delay-ps", &val)) {
+		if (val % 100)
+			return dev_err_probe(dev, -EINVAL,
+					     "rx-delay must be a multiple of 100ps\n");
+		val /= 100;
+		dev_dbg(dev, "set rx-delay to %x\n", val);
+		if (!FIELD_FIT(SYSCON_ERXDC_MASK, val))
+			return dev_err_probe(dev, -EINVAL,
+					     "RX clock delay exceeds maximum (%u00ps > %lu00ps)\n",
+					     val, FIELD_MAX(SYSCON_ERXDC_MASK));
+
+		reg |= FIELD_PREP(SYSCON_ERXDC_MASK, val);
+	}
+
+	switch (plat->phy_interface) {
+	case PHY_INTERFACE_MODE_MII:
+		/* default */
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		reg |= SYSCON_EPIT | SYSCON_ETCS_INT_GMII;
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		reg |= SYSCON_RMII_EN;
+		break;
+	default:
+		return dev_err_probe(dev, -EINVAL, "Unsupported interface mode: %s",
+				     phy_modes(plat->phy_interface));
+	}
+
+	ret = regmap_write(regmap, SYSCON_REG, reg);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "Failed to write to syscon\n");
+
+	return 0;
+}
+
+static int sun55i_gmac200_probe(struct platform_device *pdev)
+{
+	struct plat_stmmacenet_data *plat_dat;
+	struct stmmac_resources stmmac_res;
+	struct device *dev = &pdev->dev;
+	struct clk *clk;
+	int ret;
+
+	ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+	if (ret)
+		return ret;
+
+	plat_dat = devm_stmmac_probe_config_dt(pdev, stmmac_res.mac);
+	if (IS_ERR(plat_dat))
+		return PTR_ERR(plat_dat);
+
+	/* BSP disables it */
+	plat_dat->flags |= STMMAC_FLAG_SPH_DISABLE;
+	plat_dat->host_dma_width = 32;
+
+	ret = sun55i_gmac200_set_syscon(dev, plat_dat);
+	if (ret)
+		return ret;
+
+	clk = devm_clk_get_enabled(dev, "mbus");
+	if (IS_ERR(clk))
+		return dev_err_probe(dev, PTR_ERR(clk),
+				     "Failed to get or enable MBUS clock\n");
+
+	ret = devm_regulator_get_enable_optional(dev, "phy");
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to get or enable PHY supply\n");
+
+	return devm_stmmac_pltfr_probe(pdev, plat_dat, &stmmac_res);
+}
+
+static const struct of_device_id sun55i_gmac200_match[] = {
+	{ .compatible = "allwinner,sun55i-a523-gmac200" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, sun55i_gmac200_match);
+
+static struct platform_driver sun55i_gmac200_driver = {
+	.probe  = sun55i_gmac200_probe,
+	.driver = {
+		.name           = "dwmac-sun55i",
+		.pm		= &stmmac_pltfr_pm_ops,
+		.of_match_table = sun55i_gmac200_match,
+	},
+};
+module_platform_driver(sun55i_gmac200_driver);
+
+MODULE_AUTHOR("Chen-Yu Tsai <wens@csie.org>");
+MODULE_DESCRIPTION("Allwinner sun55i GMAC200 specific glue layer");
+MODULE_LICENSE("GPL");
-- 
2.47.3

Re: [PATCH net-next v7 2/6] net: stmmac: Add support for Allwinner A523 GMAC200

[Jernej Škrabec]

Dne torek, 23. september 2025 ob 16:02:42 Srednjeevropski poletni čas je Chen-Yu Tsai napisal(a):
> From: Chen-Yu Tsai <wens@csie.org>
> 
> The Allwinner A523 SoC family has a second Ethernet controller, called
> the GMAC200 in the BSP and T527 datasheet, and referred to as GMAC1 for
> numbering. This controller, according to BSP sources, is fully
> compatible with a slightly newer version of the Synopsys DWMAC core.
> The glue layer around the controller is the same as found around older
> DWMAC cores on Allwinner SoCs. The only slight difference is that since
> this is the second controller on the SoC, the register for the clock
> delay controls is at a different offset. Last, the integration includes
> a dedicated clock gate for the memory bus and the whole thing is put in
> a separately controllable power domain.
> 
> Add a new driver for this hardware supporting the integration layer.
> 
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>

Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>

Best regards,
Jernej

[PATCH net-next v7 3/6] arm64: dts: allwinner: a523: Add GMAC200 ethernet controller

[Chen-Yu Tsai]

From: Chen-Yu Tsai <wens@csie.org>

The A523 SoC family has a second ethernet controller, called the
GMAC200. It is not exposed on all the SoCs in the family.

Add a device node for it. All the hardware specific settings are from
the vendor BSP.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---

Changes since v1:
- Fixed typo in tx-queues-config
---
 .../arm64/boot/dts/allwinner/sun55i-a523.dtsi | 55 +++++++++++++++++++
 1 file changed, 55 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi b/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
index 7b36c47a3a13..a9e051a8bea3 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
@@ -182,6 +182,16 @@ rgmii0_pins: rgmii0-pins {
 				bias-disable;
 			};
 
+			rgmii1_pins: rgmii1-pins {
+				pins = "PJ0", "PJ1", "PJ2", "PJ3", "PJ4",
+				       "PJ5", "PJ6", "PJ7", "PJ8", "PJ9",
+				       "PJ11", "PJ12", "PJ13", "PJ14", "PJ15";
+				allwinner,pinmux = <5>;
+				function = "gmac1";
+				drive-strength = <40>;
+				bias-disable;
+			};
+
 			uart0_pb_pins: uart0-pb-pins {
 				pins = "PB9", "PB10";
 				allwinner,pinmux = <2>;
@@ -603,6 +613,51 @@ mdio0: mdio {
 			};
 		};
 
+		gmac1: ethernet@4510000 {
+			compatible = "allwinner,sun55i-a523-gmac200",
+				     "snps,dwmac-4.20a";
+			reg = <0x04510000 0x10000>;
+			clocks = <&ccu CLK_BUS_EMAC1>, <&ccu CLK_MBUS_EMAC1>;
+			clock-names = "stmmaceth", "mbus";
+			resets = <&ccu RST_BUS_EMAC1>;
+			reset-names = "stmmaceth";
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			pinctrl-names = "default";
+			pinctrl-0 = <&rgmii1_pins>;
+			power-domains = <&pck600 PD_VO1>;
+			syscon = <&syscon>;
+			snps,fixed-burst;
+			snps,axi-config = <&gmac1_stmmac_axi_setup>;
+			snps,mtl-rx-config = <&gmac1_mtl_rx_setup>;
+			snps,mtl-tx-config = <&gmac1_mtl_tx_setup>;
+			status = "disabled";
+
+			mdio1: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			gmac1_mtl_rx_setup: rx-queues-config {
+				snps,rx-queues-to-use = <1>;
+
+				queue0 {};
+			};
+
+			gmac1_stmmac_axi_setup: stmmac-axi-config {
+				snps,wr_osr_lmt = <0xf>;
+				snps,rd_osr_lmt = <0xf>;
+				snps,blen = <256 128 64 32 16 8 4>;
+			};
+
+			gmac1_mtl_tx_setup: tx-queues-config {
+				snps,tx-queues-to-use = <1>;
+
+				queue0 {};
+			};
+		};
+
 		ppu: power-controller@7001400 {
 			compatible = "allwinner,sun55i-a523-ppu";
 			reg = <0x07001400 0x400>;
-- 
2.47.3

[PATCH net-next v7 4/6] arm64: dts: allwinner: a527: cubie-a5e: Enable second Ethernet port

[Chen-Yu Tsai]

From: Chen-Yu Tsai <wens@csie.org>

On the Radxa Cubie A5E board, the second Ethernet controller, aka the
GMAC200, is connected to a second external Maxio MAE0621A PHY. The PHY
uses an external 25MHz crystal, and has the SoC's PJ16 pin connected to
its reset pin.

Enable the second Ethernet port. Also fix up the label for the existing
external PHY connected to the first Ethernet port. An enable delay for the
PHY supply regulator is added to make sure the PHY's internal regulators
are fully powered and the PHY is operational.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---

Changes since v1:
- Switch to generic (tx|rx)-internal-delay-ps properties
- Add PHY regulator delay
---
 .../dts/allwinner/sun55i-a527-cubie-a5e.dts   | 28 +++++++++++++++++--
 1 file changed, 26 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts b/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
index f82a8d121697..bfdf1728cd14 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
+++ b/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
@@ -14,6 +14,7 @@ / {
 
 	aliases {
 		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
 		serial0 = &uart0;
 	};
 
@@ -75,7 +76,7 @@ &ehci1 {
 
 &gmac0 {
 	phy-mode = "rgmii-id";
-	phy-handle = <&ext_rgmii_phy>;
+	phy-handle = <&ext_rgmii0_phy>;
 	phy-supply = <&reg_cldo3>;
 
 	allwinner,tx-delay-ps = <300>;
@@ -84,13 +85,24 @@ &gmac0 {
 	status = "okay";
 };
 
+&gmac1 {
+	phy-mode = "rgmii-id";
+	phy-handle = <&ext_rgmii1_phy>;
+	phy-supply = <&reg_cldo4>;
+
+	tx-internal-delay-ps = <300>;
+	rx-internal-delay-ps = <400>;
+
+	status = "okay";
+};
+
 &gpu {
 	mali-supply = <&reg_dcdc2>;
 	status = "okay";
 };
 
 &mdio0 {
-	ext_rgmii_phy: ethernet-phy@1 {
+	ext_rgmii0_phy: ethernet-phy@1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		reset-gpios = <&pio 7 8 GPIO_ACTIVE_LOW>; /* PH8 */
@@ -99,6 +111,16 @@ ext_rgmii_phy: ethernet-phy@1 {
 	};
 };
 
+&mdio1 {
+	ext_rgmii1_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		reset-gpios = <&pio 9 16 GPIO_ACTIVE_LOW>; /* PJ16 */
+		reset-assert-us = <10000>;
+		reset-deassert-us = <150000>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_cldo3>;
 	cd-gpios = <&pio 5 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PF6 */
@@ -250,6 +272,8 @@ reg_cldo4: cldo4 {
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-name = "vcc-pj-phy";
+				/* enough time for the PHY to fully power on */
+				regulator-enable-ramp-delay = <150000>;
 			};
 
 			reg_cpusldo: cpusldo {
-- 
2.47.3

[PATCH net-next v7 5/6] arm64: dts: allwinner: t527: avaota-a1: enable second Ethernet port

[Chen-Yu Tsai]

From: Chen-Yu Tsai <wens@csie.org>

On the Avaota A1 board, the second Ethernet controller, aka the GMAC200,
is connected to a second external RTL8211F-CG PHY. The PHY uses an
external 25MHz crystal, and has the SoC's PJ16 pin connected to its
reset pin.

Enable the second Ethernet port. Also fix up the label for the existing
external PHY connected to the first Ethernet port.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---

Changes since v1:
- Switch to generic (tx|rx)-internal-delay-ps properties
---
 .../dts/allwinner/sun55i-t527-avaota-a1.dts   | 26 +++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/allwinner/sun55i-t527-avaota-a1.dts b/arch/arm64/boot/dts/allwinner/sun55i-t527-avaota-a1.dts
index 1b054fa8ef74..054d0357c139 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-t527-avaota-a1.dts
+++ b/arch/arm64/boot/dts/allwinner/sun55i-t527-avaota-a1.dts
@@ -13,6 +13,7 @@ / {
 
 	aliases {
 		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
 		serial0 = &uart0;
 	};
 
@@ -73,7 +74,7 @@ &ehci1 {
 
 &gmac0 {
 	phy-mode = "rgmii-id";
-	phy-handle = <&ext_rgmii_phy>;
+	phy-handle = <&ext_rgmii0_phy>;
 	phy-supply = <&reg_dcdc4>;
 
 	allwinner,tx-delay-ps = <100>;
@@ -82,13 +83,24 @@ &gmac0 {
 	status = "okay";
 };
 
+&gmac1 {
+	phy-mode = "rgmii-id";
+	phy-handle = <&ext_rgmii1_phy>;
+	phy-supply = <&reg_dcdc4>;
+
+	tx-internal-delay-ps = <100>;
+	rx-internal-delay-ps = <100>;
+
+	status = "okay";
+};
+
 &gpu {
 	mali-supply = <&reg_dcdc2>;
 	status = "okay";
 };
 
 &mdio0 {
-	ext_rgmii_phy: ethernet-phy@1 {
+	ext_rgmii0_phy: ethernet-phy@1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
 		reset-gpios = <&pio 7 8 GPIO_ACTIVE_LOW>; /* PH8 */
@@ -97,6 +109,16 @@ ext_rgmii_phy: ethernet-phy@1 {
 	};
 };
 
+&mdio1 {
+	ext_rgmii1_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		reset-gpios = <&pio 9 16 GPIO_ACTIVE_LOW>; /* PJ16 */
+		reset-assert-us = <10000>;
+		reset-deassert-us = <150000>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_cldo3>;
 	cd-gpios = <&pio 5 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PF6 */
-- 
2.47.3

[PATCH net-next v7 6/6] arm64: dts: allwinner: t527: orangepi-4a: Enable Ethernet port

[Chen-Yu Tsai]

From: Chen-Yu Tsai <wens@csie.org>

On the Orangepi 4A board, the second Ethernet controller, aka the GMAC200,
is connected to an external Motorcomm YT8531 PHY. The PHY uses an external
25MHz crystal, has the SoC's PI15 pin connected to its reset pin, and
the PI16 pin for its interrupt pin.

Enable it.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---

Changes since v1:
- Switch to generic (tx|rx)-internal-delay-ps properties
---
 .../dts/allwinner/sun55i-t527-orangepi-4a.dts | 23 +++++++++++++++++++
 1 file changed, 23 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts b/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
index 39a4e194712a..9e6b21cf293e 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
+++ b/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
@@ -15,6 +15,7 @@ / {
 	compatible = "xunlong,orangepi-4a", "allwinner,sun55i-t527";
 
 	aliases {
+		ethernet0 = &gmac1;
 		serial0 = &uart0;
 	};
 
@@ -102,11 +103,33 @@ &ehci1 {
 	status = "okay";
 };
 
+&gmac1 {
+	phy-mode = "rgmii-id";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_cldo4>;
+
+	tx-internal-delay-ps = <0>;
+	rx-internal-delay-ps = <300>;
+
+	status = "okay";
+};
+
 &gpu {
 	mali-supply = <&reg_dcdc2>;
 	status = "okay";
 };
 
+&mdio1 {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		interrupts-extended = <&pio 8 16 IRQ_TYPE_LEVEL_LOW>; /* PI16 */
+		reset-gpios = <&pio 8 15 GPIO_ACTIVE_LOW>; /* PI15 */
+		reset-assert-us = <10000>;
+		reset-deassert-us = <150000>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_cldo3>;
 	cd-gpios = <&pio 5 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PF6 */
-- 
2.47.3

Re: [PATCH net-next v7 0/6] net: stmmac: Add support for Allwinner A523 GMAC200

[Jakub Kicinski]

On Tue, 23 Sep 2025 22:02:40 +0800 Chen-Yu Tsai wrote:
> This is v7 of my Allwinner A523 GMAC200 support series. This is based on
> next-20250922.

The dts patches don't apply to net-next which prevents our test bots
from processing the series. Could you repost just patches 1 and 2 as
a standalone series for net-next, without the dts changes?
-- 
pw-bot: cr

Re: (subset) [PATCH net-next v7 0/6] net: stmmac: Add support for Allwinner A523 GMAC200

[Chen-Yu Tsai]

On Tue, 23 Sep 2025 22:02:40 +0800, Chen-Yu Tsai wrote:
> From: Chen-Yu Tsai <wens@csie.org>
> 
> Hi everyone,
> 
> This is v7 of my Allwinner A523 GMAC200 support series. This is based on
> next-20250922.
> 
> [...]

Applied to sunxi/dt-for-6.19 in local tree, thanks!

[3/6] arm64: dts: allwinner: a523: Add GMAC200 ethernet controller
      commit: 460a71b5642a60574809032f0a21afff0f942474
[4/6] arm64: dts: allwinner: a527: cubie-a5e: Enable second Ethernet port
      commit: 7076938d20d22d5f75641f417f11edeee192e3cf
[5/6] arm64: dts: allwinner: t527: avaota-a1: enable second Ethernet port
      commit: 2e5d147ba90e887271297f69721d2d88122c7c4f
[6/6] arm64: dts: allwinner: t527: orangepi-4a: Enable Ethernet port
      commit: a3606e8a7819534026b46e2b8c7b0e156e292f13

Best regards,
-- 
Chen-Yu Tsai <wens@csie.org>