[PATCH v5 00/11] Add support for Microchip LAN969x

[PATCH v5 00/11] Add support for Microchip LAN969x

[Robert Marko]

This series adds support for the Microchip LAN969x switch SoC family.

Series is a bit long since after discussions in previous versions, it was
recommended[1][2] to add SoC specific compatibles for device nodes so it
includes the required bindings updates.

[1] https://lore.kernel.org/all/20251203-splendor-cubbyhole-eda2d6982b46@spud/
[2] https://lore.kernel.org/all/173412c8-c2fb-4c38-8de7-5b1c2eebdbf9@microchip.com/
[3] https://lore.kernel.org/all/20251203-duly-leotard-86b83bd840c6@spud/
[4] https://lore.kernel.org/all/756ead5d-8c9b-480d-8ae5-71667575ab7c@kernel.org/

Signed-off-by: Robert Marko <robert.marko@sartura.hr>

Changes in v5:
* Picked Acked-by and Reviewed-by tags
* Change clock header license to match the DTSI one
* Alphabetize EV23X71A pin nodes
* Remove the requirment for all ethernet-port nodes to have phys property
as when RGMII is used there is no SERDES being used
* Drop phys from RGMII port on EV23X71A
* Drop USB, DMA, MIIM, SPI and I2C bindings as those were already picked

Changes in v4:
* Pick Acked-by from Andi for I2C bindings
* Move clock indexes from dt-bindings into a DTS header as suggested by
Krzysztof[4]

Changes in v3:
* Pick Acked-by from Conor
* Drop HWMON binding as it was picked into hwmon already
* Document EV23X71A into AT91 binding
* Drop SparX-5 and AT91 bindings merge
* Apply remark from Conor on DMA binding regarding merging cases

Changes in v2:
* Change LAN969x wildcards to LAN9691 in patches
* Split SoC DTSI and evaluation board patches
* Add the suggested binding changes required for SoC specific compatibles
* Merge SparX-5 and AT91 bindings as suggested[3]

Robert Marko (11):
  dt-bindings: mfd: atmel,sama5d2-flexcom: add microchip,lan9691-flexcom
  dt-bindings: serial: atmel,at91-usart: add microchip,lan9691-usart
  dt-bindings: rng: atmel,at91-trng: add microchip,lan9691-trng
  dt-bindings: crypto: atmel,at91sam9g46-aes: add microchip,lan9691-aes
  dt-bindings: crypto: atmel,at91sam9g46-sha: add microchip,lan9691-sha
  dt-bindings: pinctrl: pinctrl-microchip-sgpio: add LAN969x
  arm64: dts: microchip: add LAN969x clock header file
  arm64: dts: microchip: add LAN969x support
  dt-bindings: arm: AT91: document EV23X71A board
  dt-bindings: net: sparx5: do not require phys when RGMII is used
  arm64: dts: microchip: add EV23X71A board

 .../devicetree/bindings/arm/atmel-at91.yaml   |   6 +
 .../crypto/atmel,at91sam9g46-aes.yaml         |   1 +
 .../crypto/atmel,at91sam9g46-sha.yaml         |   1 +
 .../bindings/mfd/atmel,sama5d2-flexcom.yaml   |   1 +
 .../bindings/net/microchip,sparx5-switch.yaml |  15 +-
 .../pinctrl/microchip,sparx5-sgpio.yaml       |  20 +-
 .../bindings/rng/atmel,at91-trng.yaml         |   1 +
 .../bindings/serial/atmel,at91-usart.yaml     |   1 +
 arch/arm64/boot/dts/microchip/Makefile        |   1 +
 arch/arm64/boot/dts/microchip/clk-lan9691.h   |  24 +
 arch/arm64/boot/dts/microchip/lan9691.dtsi    | 488 +++++++++++
 .../boot/dts/microchip/lan9696-ev23x71a.dts   | 756 ++++++++++++++++++
 12 files changed, 1309 insertions(+), 6 deletions(-)
 create mode 100644 arch/arm64/boot/dts/microchip/clk-lan9691.h
 create mode 100644 arch/arm64/boot/dts/microchip/lan9691.dtsi
 create mode 100644 arch/arm64/boot/dts/microchip/lan9696-ev23x71a.dts

-- 
2.52.0

[PATCH v5 01/11] dt-bindings: mfd: atmel,sama5d2-flexcom: add microchip,lan9691-flexcom

[Robert Marko]

Add binding documentation for Microchip LAN969x.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
---
Changes in v5:
* Pick Reviewed-by from Claudiu

Changes in v3:
* Pick Acked-by from Conor

 Documentation/devicetree/bindings/mfd/atmel,sama5d2-flexcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mfd/atmel,sama5d2-flexcom.yaml b/Documentation/devicetree/bindings/mfd/atmel,sama5d2-flexcom.yaml
index c7d6cf96796c..5e5dec2f6564 100644
--- a/Documentation/devicetree/bindings/mfd/atmel,sama5d2-flexcom.yaml
+++ b/Documentation/devicetree/bindings/mfd/atmel,sama5d2-flexcom.yaml
@@ -20,6 +20,7 @@ properties:
       - const: atmel,sama5d2-flexcom
       - items:
           - enum:
+              - microchip,lan9691-flexcom
               - microchip,sam9x7-flexcom
               - microchip,sama7d65-flexcom
               - microchip,sama7g5-flexcom
-- 
2.52.0

[PATCH v5 02/11] dt-bindings: serial: atmel,at91-usart: add microchip,lan9691-usart

[Robert Marko]

Document Microchip LAN969x USART compatible.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
---
Changes in v5:
* Pick Reviewed-by from Claudiu

Changes in v3:
* Pick Acked-by from Conor

 Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml b/Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml
index 087a8926f8b4..375cd50bc5cc 100644
--- a/Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml
+++ b/Documentation/devicetree/bindings/serial/atmel,at91-usart.yaml
@@ -24,6 +24,7 @@ properties:
           - const: atmel,at91sam9260-usart
       - items:
           - enum:
+              - microchip,lan9691-usart
               - microchip,sam9x60-usart
               - microchip,sam9x7-usart
               - microchip,sama7d65-usart
-- 
2.52.0

[PATCH v5 03/11] dt-bindings: rng: atmel,at91-trng: add microchip,lan9691-trng

[Robert Marko]

Document Microchip LAN969X TRNG compatible.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
---
Changes in v5:
* Pick Reviewed-by from Claudiu

Changes in v3:
* Pick Acked-by from Conor

 Documentation/devicetree/bindings/rng/atmel,at91-trng.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/rng/atmel,at91-trng.yaml b/Documentation/devicetree/bindings/rng/atmel,at91-trng.yaml
index f78614100ea8..3628251b8c51 100644
--- a/Documentation/devicetree/bindings/rng/atmel,at91-trng.yaml
+++ b/Documentation/devicetree/bindings/rng/atmel,at91-trng.yaml
@@ -19,6 +19,7 @@ properties:
           - microchip,sam9x60-trng
       - items:
           - enum:
+              - microchip,lan9691-trng
               - microchip,sama7g5-trng
           - const: atmel,at91sam9g45-trng
       - items:
-- 
2.52.0

[PATCH v5 04/11] dt-bindings: crypto: atmel,at91sam9g46-aes: add microchip,lan9691-aes

[Robert Marko]

Document Microchip LAN969x AES compatible.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
---
Changes in v5:
* Pick Reviewed-by from Claudiu

Changes in v3:
* Pick Acked-by from Conor

 .../devicetree/bindings/crypto/atmel,at91sam9g46-aes.yaml        | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-aes.yaml b/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-aes.yaml
index 19010f90198a..f3b6af6baf15 100644
--- a/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-aes.yaml
+++ b/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-aes.yaml
@@ -16,6 +16,7 @@ properties:
       - const: atmel,at91sam9g46-aes
       - items:
           - enum:
+              - microchip,lan9691-aes
               - microchip,sam9x7-aes
               - microchip,sama7d65-aes
           - const: atmel,at91sam9g46-aes
-- 
2.52.0

[PATCH v5 05/11] dt-bindings: crypto: atmel,at91sam9g46-sha: add microchip,lan9691-sha

[Robert Marko]

Document Microchip LAN969x SHA compatible.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
---
Changes in v5:
* Pick Reviewed-by from Claudiu

Changes in v3:
* Pick Acked-by from Conor

 .../devicetree/bindings/crypto/atmel,at91sam9g46-sha.yaml        | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-sha.yaml b/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-sha.yaml
index 39e076b275b3..16704ff0dd7f 100644
--- a/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-sha.yaml
+++ b/Documentation/devicetree/bindings/crypto/atmel,at91sam9g46-sha.yaml
@@ -16,6 +16,7 @@ properties:
       - const: atmel,at91sam9g46-sha
       - items:
           - enum:
+              - microchip,lan9691-sha
               - microchip,sam9x7-sha
               - microchip,sama7d65-sha
           - const: atmel,at91sam9g46-sha
-- 
2.52.0

[PATCH v5 06/11] dt-bindings: pinctrl: pinctrl-microchip-sgpio: add LAN969x

[Robert Marko]

Document LAN969x compatibles for SGPIO.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
---
Changes in v5:
* Pick Reviewed-by from Claudiu

Changes in v3:
* Pick Acked-by from Conor

 .../pinctrl/microchip,sparx5-sgpio.yaml       | 20 ++++++++++++++-----
 1 file changed, 15 insertions(+), 5 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
index fa47732d7cef..9fbbafcdc063 100644
--- a/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/microchip,sparx5-sgpio.yaml
@@ -21,10 +21,15 @@ properties:
     pattern: '^gpio@[0-9a-f]+$'
 
   compatible:
-    enum:
-      - microchip,sparx5-sgpio
-      - mscc,ocelot-sgpio
-      - mscc,luton-sgpio
+    oneOf:
+      - enum:
+          - microchip,sparx5-sgpio
+          - mscc,ocelot-sgpio
+          - mscc,luton-sgpio
+      - items:
+          - enum:
+              - microchip,lan9691-sgpio
+          - const: microchip,sparx5-sgpio
 
   '#address-cells':
     const: 1
@@ -80,7 +85,12 @@ patternProperties:
     type: object
     properties:
       compatible:
-        const: microchip,sparx5-sgpio-bank
+        oneOf:
+          - items:
+              - enum:
+                  - microchip,lan9691-sgpio-bank
+              - const: microchip,sparx5-sgpio-bank
+          - const: microchip,sparx5-sgpio-bank
 
       reg:
         description: |
-- 
2.52.0

[PATCH v5 07/11] arm64: dts: microchip: add LAN969x clock header file

[Robert Marko]

LAN969x uses hardware clock indexes, so document theses in a header to make
them humanly readable.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
---
Changes in v5:
* Relicense to GPL-2.0-or-later OR MIT to match DTSI

 arch/arm64/boot/dts/microchip/clk-lan9691.h | 24 +++++++++++++++++++++
 1 file changed, 24 insertions(+)
 create mode 100644 arch/arm64/boot/dts/microchip/clk-lan9691.h

diff --git a/arch/arm64/boot/dts/microchip/clk-lan9691.h b/arch/arm64/boot/dts/microchip/clk-lan9691.h
new file mode 100644
index 000000000000..0f2d7a0f881e
--- /dev/null
+++ b/arch/arm64/boot/dts/microchip/clk-lan9691.h
@@ -0,0 +1,24 @@
+/* SPDX-License-Identifier: (GPL-2.0-or-later OR MIT) */
+
+#ifndef _DTS_CLK_LAN9691_H
+#define _DTS_CLK_LAN9691_H
+
+#define GCK_ID_QSPI0		0
+#define GCK_ID_QSPI2		1
+#define GCK_ID_SDMMC0		2
+#define GCK_ID_SDMMC1		3
+#define GCK_ID_MCAN0		4
+#define GCK_ID_MCAN1		5
+#define GCK_ID_FLEXCOM0		6
+#define GCK_ID_FLEXCOM1		7
+#define GCK_ID_FLEXCOM2		8
+#define GCK_ID_FLEXCOM3		9
+#define GCK_ID_TIMER		10
+#define GCK_ID_USB_REFCLK	11
+
+/* Gate clocks */
+#define GCK_GATE_USB_DRD	12
+#define GCK_GATE_MCRAMC		13
+#define GCK_GATE_HMATRIX	14
+
+#endif
-- 
2.52.0

[PATCH v5 08/11] arm64: dts: microchip: add LAN969x support

[Robert Marko]

Add support for Microchip LAN969x switch SoC series by adding the SoC DTSI.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
---
Changes in v5:
* Pick Reviewed-by from Claudiu

Changes in v4:
* Adapt to clock indexes now being in a DTS header only

Changes in v2:
* Rename to lan9691
* Split SoC DTSI and evaluation board commits
* Use SoC specific compatibles for devices
* Alphanumerically sort remaining nodes
* Apply DTS coding style

 arch/arm64/boot/dts/microchip/lan9691.dtsi | 488 +++++++++++++++++++++
 1 file changed, 488 insertions(+)
 create mode 100644 arch/arm64/boot/dts/microchip/lan9691.dtsi

diff --git a/arch/arm64/boot/dts/microchip/lan9691.dtsi b/arch/arm64/boot/dts/microchip/lan9691.dtsi
new file mode 100644
index 000000000000..235e56bebbdb
--- /dev/null
+++ b/arch/arm64/boot/dts/microchip/lan9691.dtsi
@@ -0,0 +1,488 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (c) 2025 Microchip Technology Inc. and its subsidiaries.
+ */
+
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mfd/at91-usart.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+
+#include "clk-lan9691.h"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	model = "Microchip LAN969x";
+	compatible = "microchip,lan9691";
+	interrupt-parent = <&gic>;
+
+	clocks {
+		fx100_clk: fx100-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <320000000>;
+		};
+
+		cpu_clk: cpu-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <1000000000>;
+		};
+
+		ddr_clk: ddr-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <600000000>;
+		};
+
+		fabric_clk: fabric-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <250000000>;
+		};
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			next-level-cache = <&l2_0>;
+		};
+
+		l2_0: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Secure Phys IRQ */
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Non-secure Phys IRQ */
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virt IRQ */
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hyp IRQ */
+	};
+
+	axi: axi {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		usb: usb@300000 {
+			compatible = "microchip,lan9691-dwc3", "snps,dwc3";
+			reg = <0x300000 0x80000>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clks GCK_GATE_USB_DRD>,
+				 <&clks GCK_ID_USB_REFCLK>;
+			clock-names = "bus_early", "ref";
+			assigned-clocks = <&clks GCK_ID_USB_REFCLK>;
+			assigned-clock-rates = <60000000>;
+			maximum-speed = "high-speed";
+			dr_mode = "host";
+			status = "disabled";
+		};
+
+		flx0: flexcom@e0040000 {
+			compatible = "microchip,lan9691-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe0040000 0x100>;
+			ranges = <0x0 0xe0040000 0x800>;
+			clocks = <&clks GCK_ID_FLEXCOM0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			usart0: serial@200 {
+				compatible = "microchip,lan9691-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(3)>,
+				       <&dma AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi0: spi@400 {
+				compatible = "microchip,lan9691-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(3)>,
+				       <&dma AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@600 {
+				compatible = "microchip,lan9691-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(3)>,
+				       <&dma AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		flx1: flexcom@e0044000 {
+			compatible = "microchip,lan9691-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe0044000 0x100>;
+			ranges = <0x0 0xe0044000 0x800>;
+			clocks = <&clks GCK_ID_FLEXCOM1>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			usart1: serial@200 {
+				compatible = "microchip,lan9691-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(3)>,
+				       <&dma AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi1: spi@400 {
+				compatible = "microchip,lan9691-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(3)>,
+				       <&dma AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@600 {
+				compatible = "microchip,lan9691-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(3)>,
+				       <&dma AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		trng: rng@e0048000 {
+			compatible = "microchip,lan9691-trng", "atmel,at91sam9g45-trng";
+			reg = <0xe0048000 0x100>;
+			clocks = <&fabric_clk>;
+			status = "disabled";
+		};
+
+		aes: crypto@e004c000 {
+			compatible = "microchip,lan9691-aes", "atmel,at91sam9g46-aes";
+			reg = <0xe004c000 0x100>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma AT91_XDMAC_DT_PERID(12)>,
+			       <&dma AT91_XDMAC_DT_PERID(13)>;
+			dma-names = "tx", "rx";
+			clocks = <&fabric_clk>;
+			clock-names = "aes_clk";
+			status = "disabled";
+		};
+
+		flx2: flexcom@e0060000 {
+			compatible = "microchip,lan9691-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe0060000 0x100>;
+			ranges = <0x0 0xe0060000 0x800>;
+			clocks = <&clks GCK_ID_FLEXCOM2>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			usart2: serial@200 {
+				compatible = "microchip,lan9691-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(7)>,
+				       <&dma AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi2: spi@400 {
+				compatible = "microchip,lan9691-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(7)>,
+				       <&dma AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@600 {
+				compatible = "microchip,lan9691-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(7)>,
+				       <&dma AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		flx3: flexcom@e0064000 {
+			compatible = "microchip,lan9691-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe0064000 0x100>;
+			ranges = <0x0 0xe0064000 0x800>;
+			clocks = <&clks GCK_ID_FLEXCOM3>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			usart3: serial@200 {
+				compatible = "microchip,lan9691-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(9)>,
+				       <&dma AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi3: spi@400 {
+				compatible = "microchip,lan9691-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(9)>,
+				       <&dma AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@600 {
+				compatible = "microchip,lan9691-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma AT91_XDMAC_DT_PERID(9)>,
+				       <&dma AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&fabric_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		dma: dma-controller@e0068000 {
+			compatible = "microchip,lan9691-dma", "microchip,sama7g5-dma";
+			reg = <0xe0068000 0x1000>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <16>;
+			#dma-cells = <1>;
+			clocks = <&fabric_clk>;
+			clock-names = "dma_clk";
+		};
+
+		sha: crypto@e006c000 {
+			compatible = "microchip,lan9691-sha", "atmel,at91sam9g46-sha";
+			reg = <0xe006c000 0xec>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma AT91_XDMAC_DT_PERID(14)>;
+			dma-names = "tx";
+			clocks = <&fabric_clk>;
+			clock-names = "sha_clk";
+			status = "disabled";
+		};
+
+		timer: timer@e008c000 {
+			compatible = "snps,dw-apb-timer";
+			reg = <0xe008c000 0x400>;
+			clocks = <&fabric_clk>;
+			clock-names = "timer";
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		watchdog: watchdog@e0090000 {
+			compatible = "snps,dw-wdt";
+			reg = <0xe0090000 0x1000>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&fabric_clk>;
+		};
+
+		cpu_ctrl: syscon@e00c0000 {
+			compatible = "microchip,lan966x-cpu-syscon", "syscon";
+			reg = <0xe00c0000 0x350>;
+		};
+
+		switch: switch@e00c0000 {
+			compatible = "microchip,lan9691-switch";
+			reg = <0xe00c0000 0x0010000>,
+			      <0xe2010000 0x1410000>;
+			reg-names = "cpu", "devices";
+			interrupt-names = "xtr", "fdma", "ptp";
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&reset 0>;
+			reset-names = "switch";
+			status = "disabled";
+		};
+
+		clks: clock-controller@e00c00b4 {
+			compatible = "microchip,lan9691-gck";
+			reg = <0xe00c00b4 0x30>, <0xe00c0308 0x4>;
+			#clock-cells = <1>;
+			clocks = <&cpu_clk>, <&ddr_clk>, <&fx100_clk>;
+			clock-names = "cpu", "ddr", "sys";
+		};
+
+		reset: reset-controller@e201000c {
+			compatible = "microchip,lan9691-switch-reset",
+				     "microchip,lan966x-switch-reset";
+			reg = <0xe201000c 0x4>;
+			reg-names = "gcb";
+			#reset-cells = <1>;
+			cpu-syscon = <&cpu_ctrl>;
+		};
+
+		gpio: pinctrl@e20100d4 {
+			compatible = "microchip,lan9691-pinctrl";
+			reg = <0xe20100d4 0xd4>,
+			      <0xe2010370 0xa8>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&gpio 0 0 66>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+		};
+
+		mdio0: mdio@e20101a8 {
+			compatible = "microchip,lan9691-miim", "mscc,ocelot-miim";
+			reg = <0xe20101a8 0x24>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&fx100_clk>;
+			status = "disabled";
+		};
+
+		mdio1: mdio@e20101cc {
+			compatible = "microchip,lan9691-miim", "mscc,ocelot-miim";
+			reg = <0xe20101cc 0x24>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&fx100_clk>;
+			status = "disabled";
+		};
+
+		sgpio: gpio@e2010230 {
+			compatible = "microchip,lan9691-sgpio", "microchip,sparx5-sgpio";
+			reg = <0xe2010230 0x118>;
+			clocks = <&fx100_clk>;
+			resets = <&reset 0>;
+			reset-names = "switch";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sgpio_in: gpio@0 {
+				compatible = "microchip,lan9691-sgpio-bank",
+					     "microchip,sparx5-sgpio-bank";
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <3>;
+				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+			};
+
+			sgpio_out: gpio@1 {
+				compatible = "microchip,lan9691-sgpio-bank",
+					     "microchip,sparx5-sgpio-bank";
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <3>;
+			};
+		};
+
+		tmon: hwmon@e2020100 {
+			compatible = "microchip,lan9691-temp", "microchip,sparx5-temp";
+			reg = <0xe2020100 0xc>;
+			clocks = <&fx100_clk>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		serdes: serdes@e3410000 {
+			compatible = "microchip,lan9691-serdes";
+			reg = <0xe3410000 0x150000>;
+			#phy-cells = <1>;
+			clocks = <&fabric_clk>;
+		};
+
+		gic: interrupt-controller@e8c11000 {
+			compatible = "arm,gic-400";
+			reg = <0xe8c11000 0x1000>, /* Distributor GICD_ */
+			      <0xe8c12000 0x2000>, /* CPU interface GICC_ */
+			      <0xe8c14000 0x2000>, /* Virt interface control */
+			      <0xe8c16000 0x2000>; /* Virt CPU interface */
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+};
-- 
2.52.0

[PATCH v5 09/11] dt-bindings: arm: AT91: document EV23X71A board

[Robert Marko]

Microchip EV23X71A board is an LAN9696 based evaluation board.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
---
Changes in v5:
* Pick Acked-by from Conor
* Pick Reviewed-by from Claudiu

 Documentation/devicetree/bindings/arm/atmel-at91.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.yaml b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
index 68d306d17c2a..bf161e0950ea 100644
--- a/Documentation/devicetree/bindings/arm/atmel-at91.yaml
+++ b/Documentation/devicetree/bindings/arm/atmel-at91.yaml
@@ -243,6 +243,12 @@ properties:
           - const: microchip,lan9668
           - const: microchip,lan966
 
+      - description: Microchip LAN9696 EV23X71A Evaluation Board
+        items:
+          - const: microchip,ev23x71a
+          - const: microchip,lan9696
+          - const: microchip,lan9691
+
       - description: Kontron KSwitch D10 MMT series
         items:
           - enum:
-- 
2.52.0

[PATCH v5 10/11] dt-bindings: net: sparx5: do not require phys when RGMII is used

[Robert Marko]

LAN969x has 2 dedicated RGMII ports, so regular SERDES lanes are not used
for RGMII.

So, lets not require phys to be defined when any of the rgmii phy-modes are
set.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
---
 .../bindings/net/microchip,sparx5-switch.yaml     | 15 ++++++++++++++-
 1 file changed, 14 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml
index 5491d0775ede..75c7c8d1f411 100644
--- a/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml
+++ b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml
@@ -151,10 +151,23 @@ properties:
 
         required:
           - reg
-          - phys
           - phy-mode
           - microchip,bandwidth
 
+        if:
+          not:
+            properties:
+              phy-mode:
+                contains:
+                  enum:
+                    - rgmii
+                    - rgmii-id
+                    - rgmii-rxid
+                    - rgmii-txid
+        then:
+          required:
+            - phys
+
         oneOf:
           - required:
               - phy-handle
-- 
2.52.0

[PATCH v5 11/11] arm64: dts: microchip: add EV23X71A board

[Robert Marko]

Microchip EV23X71A is an LAN9696 based evaluation board.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
---
Changes in v5:
* Remove phys property from port 29
* Alphanumericaly sort pin nodes

Changes in v2:
* Split from SoC DTSI commit
* Apply DTS coding style
* Enclose array in i2c-mux
* Alphanumericaly sort nodes
* Change management port mode to RGMII-ID 

 arch/arm64/boot/dts/microchip/Makefile        |   1 +
 .../boot/dts/microchip/lan9696-ev23x71a.dts   | 756 ++++++++++++++++++
 2 files changed, 757 insertions(+)
 create mode 100644 arch/arm64/boot/dts/microchip/lan9696-ev23x71a.dts

diff --git a/arch/arm64/boot/dts/microchip/Makefile b/arch/arm64/boot/dts/microchip/Makefile
index c6e0313eea0f..09d16fc1ce9a 100644
--- a/arch/arm64/boot/dts/microchip/Makefile
+++ b/arch/arm64/boot/dts/microchip/Makefile
@@ -1,4 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_LAN969X) += lan9696-ev23x71a.dtb
 dtb-$(CONFIG_ARCH_SPARX5) += sparx5_pcb125.dtb
 dtb-$(CONFIG_ARCH_SPARX5) += sparx5_pcb134.dtb sparx5_pcb134_emmc.dtb
 dtb-$(CONFIG_ARCH_SPARX5) += sparx5_pcb135.dtb sparx5_pcb135_emmc.dtb
diff --git a/arch/arm64/boot/dts/microchip/lan9696-ev23x71a.dts b/arch/arm64/boot/dts/microchip/lan9696-ev23x71a.dts
new file mode 100644
index 000000000000..4012ea7d07bb
--- /dev/null
+++ b/arch/arm64/boot/dts/microchip/lan9696-ev23x71a.dts
@@ -0,0 +1,756 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (c) 2025 Microchip Technology Inc. and its subsidiaries.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "lan9691.dtsi"
+
+/ {
+	model = "Microchip EV23X71A";
+	compatible = "microchip,ev23x71a", "microchip,lan9696", "microchip,lan9691";
+
+	aliases {
+		serial0 = &usart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 60 GPIO_ACTIVE_LOW>;
+		open-source;
+		priority = <200>;
+	};
+
+	i2c-mux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c3>;
+		idle-state = <0x8>;
+		mux-gpios = <&sgpio_out 0 1 GPIO_ACTIVE_HIGH>,
+			    <&sgpio_out 0 2 GPIO_ACTIVE_HIGH>,
+			    <&sgpio_out 0 3 GPIO_ACTIVE_HIGH>;
+		settle-time-us = <100>;
+
+		i2c_sfp0: i2c@0 {
+			reg = <0x0>;
+		};
+
+		i2c_sfp1: i2c@1 {
+			reg = <0x1>;
+		};
+
+		i2c_sfp2: i2c@2 {
+			reg = <0x2>;
+		};
+
+		i2c_sfp3: i2c@3 {
+			reg = <0x3>;
+		};
+
+		i2c_poe: i2c@7 {
+			reg = <0x7>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-status {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio 61 GPIO_ACTIVE_LOW>;
+		};
+
+		led-sfp1-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <0>;
+			gpios = <&sgpio_out 6 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp1-yellow {
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <0>;
+			gpios = <&sgpio_out 6 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp2-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <1>;
+			gpios = <&sgpio_out 7 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp2-yellow {
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <1>;
+			gpios = <&sgpio_out 7 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp3-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <2>;
+			gpios = <&sgpio_out 8 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp3-yellow {
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <2>;
+			gpios = <&sgpio_out 8 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp4-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <3>;
+			gpios = <&sgpio_out 9 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sfp4-yellow {
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <3>;
+			gpios = <&sgpio_out 9 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&sgpio_out 1 2 GPIO_ACTIVE_LOW>,
+			    <&sgpio_out 1 3 GPIO_ACTIVE_LOW>;
+	};
+
+	sfp0: sfp0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp0>;
+		tx-disable-gpios = <&sgpio_out 6 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in 6 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 6 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 6 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp1: sfp1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp1>;
+		tx-disable-gpios = <&sgpio_out 7 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in 7 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 7 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 7 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp2: sfp2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp2>;
+		tx-disable-gpios = <&sgpio_out 8 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in 8 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 8 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 8 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp3: sfp3 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp3>;
+		tx-disable-gpios = <&sgpio_out 9 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in 9 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 9 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 9 2 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&gpio {
+	emmc_sd_pins: emmc-sd-pins {
+		/* eMMC_SD - CMD, CLK, D0, D1, D2, D3, D4, D5, D6, D7, RSTN */
+		pins = "GPIO_14", "GPIO_15", "GPIO_16", "GPIO_17",
+		       "GPIO_18", "GPIO_19", "GPIO_20", "GPIO_21",
+		       "GPIO_22", "GPIO_23", "GPIO_24";
+		function = "emmc_sd";
+	};
+
+	fan_pins: fan-pins {
+		pins = "GPIO_25", "GPIO_26";
+		function = "fan";
+	};
+
+	fc0_pins: fc0-pins {
+		pins = "GPIO_3", "GPIO_4";
+		function = "fc";
+	};
+
+	fc2_pins: fc2-pins {
+		pins = "GPIO_64", "GPIO_65", "GPIO_66";
+		function = "fc";
+	};
+
+	fc3_pins: fc3-pins {
+		pins = "GPIO_55", "GPIO_56";
+		function = "fc";
+	};
+
+	mdio_irq_pins: mdio-irq-pins {
+		pins = "GPIO_11";
+		function = "miim_irq";
+	};
+
+	mdio_pins: mdio-pins {
+		pins = "GPIO_9", "GPIO_10";
+		function = "miim";
+	};
+
+	ptp_ext_pins: ptp-ext-pins {
+		pins = "GPIO_59";
+		function = "ptpsync_5";
+	};
+
+	ptp_out_pins: ptp-out-pins {
+		pins = "GPIO_58";
+		function = "ptpsync_4";
+	};
+
+	sgpio_pins: sgpio-pins {
+		/* SCK, D0, D1, LD */
+		pins = "GPIO_5", "GPIO_6", "GPIO_7", "GPIO_8";
+		function = "sgpio_a";
+	};
+
+	usb_over_pins: usb-over-pins {
+		pins = "GPIO_13";
+		function = "usb_over_detect";
+	};
+
+	usb_power_pins: usb-power-pins {
+		pins = "GPIO_1";
+		function = "usb_power";
+	};
+
+	usb_rst_pins: usb-rst-pins {
+		pins = "GPIO_12";
+		function = "usb2phy_rst";
+	};
+
+	usb_ulpi_pins: usb-ulpi-pins {
+		pins = "GPIO_30", "GPIO_31", "GPIO_32", "GPIO_33",
+		       "GPIO_34", "GPIO_35", "GPIO_36", "GPIO_37",
+		       "GPIO_38", "GPIO_39", "GPIO_40", "GPIO_41";
+		function = "usb_ulpi";
+	};
+};
+
+&flx0 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+};
+
+&flx2 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "okay";
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-0 = <&fc3_pins>;
+	pinctrl-names = "default";
+	i2c-analog-filter;
+	i2c-digital-filter;
+	i2c-digital-filter-width-ns = <35>;
+	i2c-sda-hold-time-ns = <1500>;
+	status = "okay";
+};
+
+&mdio0 {
+	pinctrl-0 = <&mdio_pins>, <&mdio_irq_pins>;
+	pinctrl-names = "default";
+	reset-gpios = <&gpio 62 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	phy3: phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <3>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy4: phy@4 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <4>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy5: phy@5 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <5>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy6: phy@6 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <6>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy7: phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy8: phy@8 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <8>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy9: phy@9 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <9>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy10: phy@10 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <10>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy11: phy@11 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <11>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy12: phy@12 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <12>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy13: phy@13 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <13>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy14: phy@14 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <14>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy15: phy@15 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <15>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy16: phy@16 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <16>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy17: phy@17 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <17>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy18: phy@18 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <18>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy19: phy@19 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <19>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy20: phy@20 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <20>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy21: phy@21 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <21>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy22: phy@22 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <22>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy23: phy@23 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <23>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy24: phy@24 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <24>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy25: phy@25 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <25>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy26: phy@26 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <26>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+
+	phy27: phy@27 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <27>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+	};
+};
+
+&serdes {
+	status = "okay";
+};
+
+&sgpio {
+	pinctrl-0 = <&sgpio_pins>;
+	pinctrl-names = "default";
+	microchip,sgpio-port-ranges = <0 1>, <6 9>;
+	status = "okay";
+
+	gpio@0 {
+		ngpios = <128>;
+	};
+	gpio@1 {
+		ngpios = <128>;
+	};
+};
+
+&spi2 {
+	pinctrl-0 = <&fc2_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&gpio 63 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&switch {
+	pinctrl-0 = <&ptp_out_pins>, <&ptp_ext_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	ethernet-ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port0: port@0 {
+			reg = <0>;
+			phy-handle = <&phy4>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 0>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port1: port@1 {
+			reg = <1>;
+			phy-handle = <&phy5>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 0>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port2: port@2 {
+			reg = <2>;
+			phy-handle = <&phy6>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 0>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port3: port@3 {
+			reg = <3>;
+			phy-handle = <&phy7>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 0>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port4: port@4 {
+			reg = <4>;
+			phy-handle = <&phy8>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 1>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port5: port@5 {
+			reg = <5>;
+			phy-handle = <&phy9>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 1>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port6: port@6 {
+			reg = <6>;
+			phy-handle = <&phy10>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 1>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port7: port@7 {
+			reg = <7>;
+			phy-handle = <&phy11>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 1>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port8: port@8 {
+			reg = <8>;
+			phy-handle = <&phy12>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 2>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port9: port@9 {
+			reg = <9>;
+			phy-handle = <&phy13>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 2>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port10: port@10 {
+			reg = <10>;
+			phy-handle = <&phy14>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 2>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port11: port@11 {
+			reg = <11>;
+			phy-handle = <&phy15>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 2>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port12: port@12 {
+			reg = <12>;
+			phy-handle = <&phy16>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 3>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port13: port@13 {
+			reg = <13>;
+			phy-handle = <&phy17>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 3>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port14: port@14 {
+			reg = <14>;
+			phy-handle = <&phy18>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 3>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port15: port@15 {
+			reg = <15>;
+			phy-handle = <&phy19>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 3>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port16: port@16 {
+			reg = <16>;
+			phy-handle = <&phy20>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 4>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port17: port@17 {
+			reg = <17>;
+			phy-handle = <&phy21>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 4>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port18: port@18 {
+			reg = <18>;
+			phy-handle = <&phy22>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 4>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port19: port@19 {
+			reg = <19>;
+			phy-handle = <&phy23>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 4>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port20: port@20 {
+			reg = <20>;
+			phy-handle = <&phy24>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 5>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port21: port@21 {
+			reg = <21>;
+			phy-handle = <&phy25>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 5>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port22: port@22 {
+			reg = <22>;
+			phy-handle = <&phy26>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 5>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port23: port@23 {
+			reg = <23>;
+			phy-handle = <&phy27>;
+			phy-mode = "qsgmii";
+			phys = <&serdes 5>;
+			microchip,bandwidth = <1000>;
+		};
+
+		port24: port@24 {
+			reg = <24>;
+			phys = <&serdes 6>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp0>;
+			managed = "in-band-status";
+			microchip,bandwidth = <10000>;
+			microchip,sd-sgpio = <24>;
+		};
+
+		port25: port@25 {
+			reg = <25>;
+			phys = <&serdes 7>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp1>;
+			managed = "in-band-status";
+			microchip,bandwidth = <10000>;
+			microchip,sd-sgpio = <28>;
+		};
+
+		port26: port@26 {
+			reg = <26>;
+			phys = <&serdes 8>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp2>;
+			managed = "in-band-status";
+			microchip,bandwidth = <10000>;
+			microchip,sd-sgpio = <32>;
+		};
+
+		port27: port@27 {
+			reg = <27>;
+			phys = <&serdes 9>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp3>;
+			managed = "in-band-status";
+			microchip,bandwidth = <10000>;
+			microchip,sd-sgpio = <36>;
+		};
+
+		port29: port@29 {
+			reg = <29>;
+			phy-handle = <&phy3>;
+			phy-mode = "rgmii-id";
+			microchip,bandwidth = <1000>;
+		};
+	};
+};
+
+&tmon {
+	pinctrl-0 = <&fan_pins>;
+	pinctrl-names = "default";
+};
+
+&usart0 {
+	pinctrl-0 = <&fc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb {
+	pinctrl-0 = <&usb_ulpi_pins>, <&usb_rst_pins>, <&usb_over_pins>, <&usb_power_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
-- 
2.52.0

Re: [PATCH v5 07/11] arm64: dts: microchip: add LAN969x clock header file

[claudiu beznea]

On 1/15/26 13:37, Robert Marko wrote:
> LAN969x uses hardware clock indexes, so document theses in a header to make
> them humanly readable.
> 
> Signed-off-by: Robert Marko<robert.marko@sartura.hr>

Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>

Re: [PATCH v5 11/11] arm64: dts: microchip: add EV23X71A board

[Claudiu Beznea]

On 1/15/26 13:37, Robert Marko wrote:
> Microchip EV23X71A is an LAN9696 based evaluation board.
> 
> Signed-off-by: Robert Marko<robert.marko@sartura.hr>

Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>

Re: [PATCH v5 10/11] dt-bindings: net: sparx5: do not require phys when RGMII is used

[Rob Herring (Arm)]

On Thu, 15 Jan 2026 12:37:35 +0100, Robert Marko wrote:
> LAN969x has 2 dedicated RGMII ports, so regular SERDES lanes are not used
> for RGMII.
> 
> So, lets not require phys to be defined when any of the rgmii phy-modes are
> set.
> 
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> ---
>  .../bindings/net/microchip,sparx5-switch.yaml     | 15 ++++++++++++++-
>  1 file changed, 14 insertions(+), 1 deletion(-)
> 

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

Re: [PATCH v5 10/11] dt-bindings: net: sparx5: do not require phys when RGMII is used

[Jakub Kicinski]

On Thu, 15 Jan 2026 12:37:35 +0100 Robert Marko wrote:
> LAN969x has 2 dedicated RGMII ports, so regular SERDES lanes are not used
> for RGMII.
> 
> So, lets not require phys to be defined when any of the rgmii phy-modes are
> set.

Applied, thanks!

Re: [PATCH v5 06/11] dt-bindings: pinctrl: pinctrl-microchip-sgpio: add LAN969x

[Linus Walleij]

Hi Robert,

On Thu, Jan 15, 2026 at 12:41 PM Robert Marko <robert.marko@sartura.hr> wrote:

> Document LAN969x compatibles for SGPIO.
>
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>

Should I just merge this one patch to the pinctrl tree?
Looks good to me.

Yours,
Linus Walleij

Re: [PATCH v5 06/11] dt-bindings: pinctrl: pinctrl-microchip-sgpio: add LAN969x

[Robert Marko]

On Wed, Jan 21, 2026 at 1:44 PM Linus Walleij <linusw@kernel.org> wrote:
>
> Hi Robert,
>
> On Thu, Jan 15, 2026 at 12:41 PM Robert Marko <robert.marko@sartura.hr> wrote:
>
> > Document LAN969x compatibles for SGPIO.
> >
> > Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> > Acked-by: Conor Dooley <conor.dooley@microchip.com>
> > Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
>
> Should I just merge this one patch to the pinctrl tree?

That would be great as other bindings are slowly being picked into
their respective trees.

Regards,
Robert
> Looks good to me.
>
> Yours,
> Linus Walleij



-- 
Robert Marko
Staff Embedded Linux Engineer
Sartura d.d.
Lendavska ulica 16a
10000 Zagreb, Croatia
Email: robert.marko@sartura.hr
Web: www.sartura.hr

Re: [PATCH v5 06/11] dt-bindings: pinctrl: pinctrl-microchip-sgpio: add LAN969x

[Linus Walleij]

On Thu, Jan 15, 2026 at 12:41 PM Robert Marko <robert.marko@sartura.hr> wrote:

> Document LAN969x compatibles for SGPIO.
>
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>

This patch 6/11 applied to the pinctrl tree!

Yours,
Linus Walleij

Re: [PATCH v5 00/11] Add support for Microchip LAN969x

[Herbert Xu]

On Thu, Jan 15, 2026 at 12:37:25PM +0100, Robert Marko wrote:
> This series adds support for the Microchip LAN969x switch SoC family.
> 
> Series is a bit long since after discussions in previous versions, it was
> recommended[1][2] to add SoC specific compatibles for device nodes so it
> includes the required bindings updates.
> 
> [1] https://lore.kernel.org/all/20251203-splendor-cubbyhole-eda2d6982b46@spud/
> [2] https://lore.kernel.org/all/173412c8-c2fb-4c38-8de7-5b1c2eebdbf9@microchip.com/
> [3] https://lore.kernel.org/all/20251203-duly-leotard-86b83bd840c6@spud/
> [4] https://lore.kernel.org/all/756ead5d-8c9b-480d-8ae5-71667575ab7c@kernel.org/
> 
> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
> 
> Changes in v5:
> * Picked Acked-by and Reviewed-by tags
> * Change clock header license to match the DTSI one
> * Alphabetize EV23X71A pin nodes
> * Remove the requirment for all ethernet-port nodes to have phys property
> as when RGMII is used there is no SERDES being used
> * Drop phys from RGMII port on EV23X71A
> * Drop USB, DMA, MIIM, SPI and I2C bindings as those were already picked
> 
> Changes in v4:
> * Pick Acked-by from Andi for I2C bindings
> * Move clock indexes from dt-bindings into a DTS header as suggested by
> Krzysztof[4]
> 
> Changes in v3:
> * Pick Acked-by from Conor
> * Drop HWMON binding as it was picked into hwmon already
> * Document EV23X71A into AT91 binding
> * Drop SparX-5 and AT91 bindings merge
> * Apply remark from Conor on DMA binding regarding merging cases
> 
> Changes in v2:
> * Change LAN969x wildcards to LAN9691 in patches
> * Split SoC DTSI and evaluation board patches
> * Add the suggested binding changes required for SoC specific compatibles
> * Merge SparX-5 and AT91 bindings as suggested[3]
> 
> Robert Marko (11):
>   dt-bindings: mfd: atmel,sama5d2-flexcom: add microchip,lan9691-flexcom
>   dt-bindings: serial: atmel,at91-usart: add microchip,lan9691-usart
>   dt-bindings: rng: atmel,at91-trng: add microchip,lan9691-trng
>   dt-bindings: crypto: atmel,at91sam9g46-aes: add microchip,lan9691-aes
>   dt-bindings: crypto: atmel,at91sam9g46-sha: add microchip,lan9691-sha
>   dt-bindings: pinctrl: pinctrl-microchip-sgpio: add LAN969x
>   arm64: dts: microchip: add LAN969x clock header file
>   arm64: dts: microchip: add LAN969x support
>   dt-bindings: arm: AT91: document EV23X71A board
>   dt-bindings: net: sparx5: do not require phys when RGMII is used
>   arm64: dts: microchip: add EV23X71A board
> 
>  .../devicetree/bindings/arm/atmel-at91.yaml   |   6 +
>  .../crypto/atmel,at91sam9g46-aes.yaml         |   1 +
>  .../crypto/atmel,at91sam9g46-sha.yaml         |   1 +
>  .../bindings/mfd/atmel,sama5d2-flexcom.yaml   |   1 +
>  .../bindings/net/microchip,sparx5-switch.yaml |  15 +-
>  .../pinctrl/microchip,sparx5-sgpio.yaml       |  20 +-
>  .../bindings/rng/atmel,at91-trng.yaml         |   1 +
>  .../bindings/serial/atmel,at91-usart.yaml     |   1 +
>  arch/arm64/boot/dts/microchip/Makefile        |   1 +
>  arch/arm64/boot/dts/microchip/clk-lan9691.h   |  24 +
>  arch/arm64/boot/dts/microchip/lan9691.dtsi    | 488 +++++++++++
>  .../boot/dts/microchip/lan9696-ev23x71a.dts   | 756 ++++++++++++++++++
>  12 files changed, 1309 insertions(+), 6 deletions(-)
>  create mode 100644 arch/arm64/boot/dts/microchip/clk-lan9691.h
>  create mode 100644 arch/arm64/boot/dts/microchip/lan9691.dtsi
>  create mode 100644 arch/arm64/boot/dts/microchip/lan9696-ev23x71a.dts
> 
> -- 
> 2.52.0

Patches 4-5 applied.  Thanks.
-- 
Email: Herbert Xu <herbert@gondor.apana.org.au>
Home Page: http://gondor.apana.org.au/~herbert/
PGP Key: http://gondor.apana.org.au/~herbert/pubkey.txt

Re: [PATCH v5 08/11] arm64: dts: microchip: add LAN969x support

[Daniel Machon]

> Add support for Microchip LAN969x switch SoC series by adding the SoC DTSI.

Acked-by: Daniel Machon <daniel.machon@microchip.com>

Re: [PATCH v5 11/11] arm64: dts: microchip: add EV23X71A board

[Daniel Machon]

Hi Robert,

Tested on EV23X71A.

Thanks!

> Microchip EV23X71A is an LAN9696 based evaluation board.

Acked-by: Daniel Machon <daniel.machon@microchip.com>
Tested-by: Daniel Machon <daniel.machon@microchip.com>