From: Meghana Malladi <m-malladi@ti.com>
To: <nm@ti.com>, <vigneshr@ti.com>
Cc: <conor+dt@kernel.org>, <krzk+dt@kernel.org>, <robh@kernel.org>,
<kristo@kernel.org>, <linux-kernel@vger.kernel.org>,
<devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>, <netdev@vger.kernel.org>,
<srk@ti.com>, Roger Quadros <rogerq@kernel.org>,
<danishanwar@ti.com>, <m-malladi@ti.com>
Subject: [PATCH v2 1/2] arm64: dts: ti: k3-am642-evm: Add ICSSG0 overlay for dual EMAC support
Date: Sat, 28 Feb 2026 17:02:02 +0530 [thread overview]
Message-ID: <20260228113203.498839-2-m-malladi@ti.com> (raw)
In-Reply-To: <20260228113203.498839-1-m-malladi@ti.com>
Add device tree overlay to enable ICSSG0 dual EMAC support on AM642 EVM.
This overlay enables both ICSSG0 Ethernet interfaces (port0 and port1) in
dual EMAC mode.
Users can combine this with the existing ICSSG1 overlay to enable all four
ICSSG interfaces if needed.
Signed-off-by: Meghana Malladi <m-malladi@ti.com>
---
v1: https://lore.kernel.org/all/20260226115454.1730618-1-m-malladi@ti.com/
v2-v1:
- Drop bringing up ICSSG1 support in this overlay as suggested by
MD Danish Anwar <danishanwar@ti.com>
arch/arm64/boot/dts/ti/Makefile | 4 +
.../boot/dts/ti/k3-am642-evm-icssg0.dtso | 203 ++++++++++++++++++
2 files changed, 207 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-am642-evm-icssg0.dtso
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index ba01a929e06f..d2cd124a5b08 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -62,6 +62,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62x-sk-hdmi-audio.dtbo
# Boards with AM64x SoC
dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am642-evm-icssg0.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am642-evm-icssg1-dualemac.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am642-evm-icssg1-dualemac-mii.dtbo
dtb-$(CONFIG_ARCH_K3) += k3-am642-evm-pcie0-ep.dtbo
@@ -218,6 +219,8 @@ k3-am62p5-sk-csi2-ov5640-dtbs := k3-am62p5-sk.dtb \
k3-am62x-sk-csi2-ov5640.dtbo
k3-am62p5-sk-csi2-tevi-ov5640-dtbs := k3-am62p5-sk.dtb \
k3-am62x-sk-csi2-tevi-ov5640.dtbo
+k3-am642-evm-icssg0-dtbs := \
+ k3-am642-evm.dtb k3-am642-evm-icssg0.dtbo
k3-am642-evm-icssg1-dualemac-dtbs := \
k3-am642-evm.dtb k3-am642-evm-icssg1-dualemac.dtbo
k3-am642-evm-icssg1-dualemac-mii-dtbs := \
@@ -306,6 +309,7 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
k3-am62p5-sk-csi2-imx219.dtb \
k3-am62p5-sk-csi2-ov5640.dtb \
k3-am62p5-sk-csi2-tevi-ov5640.dtb \
+ k3-am642-evm-icssg0.dtb \
k3-am642-evm-icssg1-dualemac.dtb \
k3-am642-evm-icssg1-dualemac-mii.dtb \
k3-am642-evm-pcie0-ep.dtb \
diff --git a/arch/arm64/boot/dts/ti/k3-am642-evm-icssg0.dtso b/arch/arm64/boot/dts/ti/k3-am642-evm-icssg0.dtso
new file mode 100644
index 000000000000..425a16948cc1
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am642-evm-icssg0.dtso
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+/**
+ * DT overlay for enabling ICSSG0 dual EMAC on AM642 EVM
+ *
+ * AM642 EVM Product link: https://www.ti.com/tool/TMDS64EVM
+ * DP83TG720 daughter card link: https://www.ti.com/tool/DP83TG720-IND-SPE-EVM
+ *
+ * Copyright (C) 2020-2024 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "k3-pinctrl.h"
+
+&{/aliases} {
+ ethernet0 = &icssg0_emac0;
+ ethernet1 = &icssg0_emac1;
+};
+
+&{/} {
+ icssg0_eth: icssg0-eth {
+ compatible = "ti,am642-icssg-prueth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pru_icssg0_rgmii1_pins_default>, <&pru_icssg0_rgmii2_pins_default>;
+
+ sram = <&oc_sram>;
+ ti,prus = <&pru0_0>, <&rtu0_0>, <&tx_pru0_0>, <&pru0_1>, <&rtu0_1>, <&tx_pru0_1>;
+ firmware-name = "ti-pruss/am64x-sr2-pru0-prueth-fw.elf",
+ "ti-pruss/am64x-sr2-rtu0-prueth-fw.elf",
+ "ti-pruss/am64x-sr2-txpru0-prueth-fw.elf",
+ "ti-pruss/am64x-sr2-pru1-prueth-fw.elf",
+ "ti-pruss/am64x-sr2-rtu1-prueth-fw.elf",
+ "ti-pruss/am64x-sr2-txpru1-prueth-fw.elf";
+
+ ti,pruss-gp-mux-sel = <2>, /* MII mode */
+ <2>,
+ <2>,
+ <2>, /* MII mode */
+ <2>,
+ <2>;
+
+ ti,mii-g-rt = <&icssg0_mii_g_rt>;
+ ti,mii-rt = <&icssg0_mii_rt>;
+ ti,pa-stats = <&icssg0_pa_stats>;
+ ti,iep = <&icssg0_iep0>, <&icssg0_iep1>;
+
+ interrupt-parent = <&icssg0_intc>;
+ interrupts = <24 0 2>, <25 1 3>;
+ interrupt-names = "tx_ts0", "tx_ts1";
+
+ dmas = <&main_pktdma 0xc100 0>, /* egress slice 0 */
+ <&main_pktdma 0xc101 0>, /* egress slice 0 */
+ <&main_pktdma 0xc102 0>, /* egress slice 0 */
+ <&main_pktdma 0xc103 0>, /* egress slice 0 */
+ <&main_pktdma 0xc104 0>, /* egress slice 1 */
+ <&main_pktdma 0xc105 0>, /* egress slice 1 */
+ <&main_pktdma 0xc106 0>, /* egress slice 1 */
+ <&main_pktdma 0xc107 0>, /* egress slice 1 */
+ <&main_pktdma 0x4100 0>, /* ingress slice 0 */
+ <&main_pktdma 0x4101 0>, /* ingress slice 1 */
+ <&main_pktdma 0x4102 0>, /* mgmnt rsp slice 0 */
+ <&main_pktdma 0x4103 0>; /* mgmnt rsp slice 1 */
+ dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
+ "tx1-0", "tx1-1", "tx1-2", "tx1-3",
+ "rx0", "rx1",
+ "rxmgm0", "rxmgm1";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ icssg0_emac0: port@0 {
+ reg = <0>;
+ phy-handle = <&icssg0_phy00>;
+ phy-mode = "rgmii-id";
+ syscon-rgmii-delay = <&main_conf 0x4100>;
+ /* Filled in by bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ };
+
+ icssg0_emac1: port@1 {
+ reg = <1>;
+ phy-handle = <&icssg0_phy01>;
+ phy-mode = "rgmii-id";
+ syscon-rgmii-delay = <&main_conf 0x4104>;
+ /* Filled in by bootloader */
+ local-mac-address = [00 00 00 00 00 00];
+ };
+ };
+ };
+};
+
+&main_pmx0 {
+ pru_icssg0_mdio_pins_default: pru-icssg0-mdio-pins-default {
+ pinctrl-single,pins = <
+ /* (P3) PRG0_MDIO0_MDC */
+ AM64X_IOPAD(0x0204, PIN_OUTPUT, 0)
+ /* (P2) PRG0_MDIO0_MDIO */
+ AM64X_IOPAD(0x0200, PIN_INPUT, 0)
+ /* (P16) GPIO0_32 - GPMC0_ADVn_ALE - GPIO_ETH0/1_RESETn# */
+ AM64X_IOPAD(0x0084, PIN_OUTPUT, 7)
+ >;
+ };
+
+ pru_icssg0_rgmii1_pins_default: pru-icssg0-rgmii1-pins-default {
+ pinctrl-single,pins = <
+ /* (module-sitara) */
+ /* (a14-y1) PRG0_PRU0_GPO0.PRG0_RGMII1_RD0 */
+ AM64X_IOPAD(0x0160, PIN_INPUT, 2)
+ /* (b14-r4) PRG0_PRU0_GPO1.PRG0_RGMII1_RD1 */
+ AM64X_IOPAD(0x0164, PIN_INPUT, 2)
+ /* (d14-u2) PRG0_PRU0_GPO2.PRG0_RGMII1_RD2 */
+ AM64X_IOPAD(0x0168, PIN_INPUT, 2)
+ /* (e14-v2) PRG0_PRU0_GPO3.PRG0_RGMII1_RD3 */
+ AM64X_IOPAD(0x016c, PIN_INPUT, 2)
+ /* (e13-t3) PRG0_PRU0_GPO6.PRG0_RGMII1_RXC */
+ AM64X_IOPAD(0x0178, PIN_INPUT, 2)
+ /* (b13-aa2) PRG0_PRU0_GPO4.PRG0_RGMII1_RX_CTL */
+ AM64X_IOPAD(0x0170, PIN_INPUT, 2)
+
+ /* (a11-y3) PRG0_PRU0_GPO11.PRG0_RGMII1_TD0 */
+ AM64X_IOPAD(0x018c, PIN_OUTPUT, 2)
+ /* (c11-aa3) PRG0_PRU0_GPO12.PRG0_RGMII1_TD1 */
+ AM64X_IOPAD(0x0190, PIN_OUTPUT, 2)
+ /* (d11-r6) PRG0_PRU0_GPO13.PRG0_RGMII1_TD2 */
+ AM64X_IOPAD(0x0194, PIN_OUTPUT, 2)
+ /* (b10-v4) PRG0_PRU0_GPO14.PRG0_RGMII1_TD3 */
+ AM64X_IOPAD(0x0198, PIN_OUTPUT, 2)
+ /* (e10-u4) PRG0_PRU0_GPO16.PRG0_RGMII1_TXC */
+ AM64X_IOPAD(0x01a0, PIN_OUTPUT, 2)
+ /* (c10-t5) PRG0_PRU0_GPO15.PRG0_RGMII1_TX_CTL */
+ AM64X_IOPAD(0x019c, PIN_OUTPUT, 2)
+ >;
+ };
+
+ pru_icssg0_rgmii2_pins_default: pru-icssg0-rgmii2-pins-default {
+ pinctrl-single,pins = <
+ /* (e9-y2) PRG0_PRU1_GPO0.PRG0_RGMII2_RD0 */
+ AM64X_IOPAD(0x01b0, PIN_INPUT, 2)
+ /* (a8-w2) PRG0_PRU1_GPO1.PRG0_RGMII2_RD1 */
+ AM64X_IOPAD(0x01b4, PIN_INPUT, 2)
+ /* (c8-v3) PRG0_PRU1_GPO2.PRG0_RGMII2_RD2 */
+ AM64X_IOPAD(0x01b8, PIN_INPUT, 2)
+ /* (d8-t4) PRG0_PRU1_GPO3.PRG0_RGMII2_RD3 */
+ AM64X_IOPAD(0x01bc, PIN_INPUT, 2)
+ /* (e7-r5) PRG0_PRU1_GPO6.PRG0_RGMII2_RXC */
+ AM64X_IOPAD(0x01c8, PIN_INPUT, 2)
+ /* (b7-w3) PRG0_PRU1_GPO4.PRG0_RGMII2_RX_CTL */
+ AM64X_IOPAD(0x01c0, PIN_INPUT, 2)
+
+ /* (a5-w4) PRG0_PRU1_GPO11.PRG0_RGMII2_TD0 */
+ AM64X_IOPAD(0x01dc, PIN_OUTPUT, 2)
+ /* (c5-y4) PRG0_PRU1_GPO12.PRG0_RGMII2_TD1 */
+ AM64X_IOPAD(0x01e0, PIN_OUTPUT, 2)
+ /* (d5-t6) PRG0_PRU1_GPO13.PRG0_RGMII2_TD2 */
+ AM64X_IOPAD(0x01e4, PIN_OUTPUT, 2)
+ /* (b4-u6) PRG0_PRU1_GPO14.PRG0_RGMII2_TD3 */
+ AM64X_IOPAD(0x01e8, PIN_OUTPUT, 2)
+ /* (a3-aa4) PRG0_PRU1_GPO16.PRG0_RGMII2_TXC */
+ AM64X_IOPAD(0x01f0, PIN_OUTPUT, 2)
+ /* (c4-u5) PRG0_PRU1_GPO15.PRG0_RGMII2_TX_CTL */
+ AM64X_IOPAD(0x01ec, PIN_OUTPUT, 2)
+ >;
+ };
+
+ icssg0_iep0_pins_default: icssg0-iep0-pins-default {
+ pinctrl-single,pins = <
+ AM64X_IOPAD(0x01ac, PIN_OUTPUT, 2) /* (W1) PRG0_PRU0_GPO19.PRG0_IEP0_EDC_SYNC_OUT0 */
+ >;
+ };
+};
+
+&icssg0_mdio {
+ pinctrl-names = "default";
+ status = "okay";
+ pinctrl-0 = <&pru_icssg0_mdio_pins_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ icssg0_phy00: ethernet-phy@0 {
+ reg = <0x0>;
+ };
+
+ icssg0_phy01: ethernet-phy@1 {
+ reg = <0xA>;
+ };
+};
+
+&icssg0_iep0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&icssg0_iep0_pins_default>;
+};
+
+&main_gpio0 {
+ phy-line-hog {
+ gpio-hog;
+ gpios = <32 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "phy-hog-line";
+ };
+};
--
2.43.0
next prev parent reply other threads:[~2026-02-28 11:32 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-02-28 11:32 [PATCH v2 0/2] Add ICSSG0 dual EMAC support for AM642 EVM Meghana Malladi
2026-02-28 11:32 ` Meghana Malladi [this message]
2026-03-09 4:44 ` [PATCH v2 1/2] arm64: dts: ti: k3-am642-evm: Add ICSSG0 overlay for dual EMAC support Vignesh Raghavendra
2026-02-28 11:32 ` [PATCH v2 2/2] arm64: defconfig: Enable DP83TG720 PHY driver Meghana Malladi
2026-03-04 15:32 ` [PATCH v2 0/2] Add ICSSG0 dual EMAC support for AM642 EVM Daolin Qiu
2026-03-04 15:44 ` Krzysztof Kozlowski
2026-03-07 0:21 ` Daolin Qiu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260228113203.498839-2-m-malladi@ti.com \
--to=m-malladi@ti.com \
--cc=conor+dt@kernel.org \
--cc=danishanwar@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=kristo@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=nm@ti.com \
--cc=robh@kernel.org \
--cc=rogerq@kernel.org \
--cc=srk@ti.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox