public inbox for netdev@vger.kernel.org
 help / color / mirror / Atom feed
From: hawk@kernel.org
To: netdev@vger.kernel.org
Cc: hawk@kernel.org, andrew+netdev@lunn.ch, davem@davemloft.net,
	edumazet@google.com, kuba@kernel.org, pabeni@redhat.com,
	horms@kernel.org, jhs@mojatatu.com, jiri@resnulli.us,
	j.koeppeler@tu-berlin.de, kernel-team@cloudflare.com
Subject: [PATCH net-next 3/5] veth: add tx_timeout watchdog as BQL safety net
Date: Tue, 24 Mar 2026 18:47:02 +0100	[thread overview]
Message-ID: <20260324174719.1224337-5-hawk@kernel.org> (raw)
In-Reply-To: <20260324174719.1224337-1-hawk@kernel.org>

From: Jesper Dangaard Brouer <hawk@kernel.org>

With the introduction of BQL (Byte Queue Limits) for veth, there are
now two independent mechanisms that can stop a transmit queue:

 - DRV_XOFF: set by netif_tx_stop_queue() when the ptr_ring is full
 - STACK_XOFF: set by BQL when the byte-in-flight limit is reached

If either mechanism stalls without a corresponding wake/completion,
the queue stops permanently. Enable the net device watchdog timer and
implement ndo_tx_timeout as a failsafe recovery.

The timeout handler resets BQL state (clearing STACK_XOFF) and wakes
the queue (clearing DRV_XOFF), covering both stop mechanisms. The
watchdog fires after 16 seconds, which accommodates worst-case NAPI
processing (budget=64 packets x 250ms per-packet consumer delay)
without false positives under normal backpressure.

Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Tested-by: Jonas Köppeler <j.koeppeler@tu-berlin.de>
---
 drivers/net/veth.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/net/veth.c b/drivers/net/veth.c
index b9a79d066703..beb4c31d8fd7 100644
--- a/drivers/net/veth.c
+++ b/drivers/net/veth.c
@@ -1426,6 +1426,22 @@ static int veth_set_channels(struct net_device *dev,
 	goto out;
 }
 
+static void veth_tx_timeout(struct net_device *dev, unsigned int txqueue)
+{
+	struct netdev_queue *txq = netdev_get_tx_queue(dev, txqueue);
+
+	netdev_err(dev,
+		   "veth backpressure(0x%lX) stalled(n:%ld) TXQ(%u) re-enable\n",
+		   txq->state, atomic_long_read(&txq->trans_timeout), txqueue);
+
+	/* Clear both stop mechanisms:
+	 * - DRV_XOFF: set by netif_tx_stop_queue (ptr_ring backpressure)
+	 * - STACK_XOFF: set by BQL when byte limit is reached
+	 */
+	netdev_tx_reset_queue(txq);
+	netif_tx_wake_queue(txq);
+}
+
 static int veth_open(struct net_device *dev)
 {
 	struct veth_priv *priv = netdev_priv(dev);
@@ -1764,6 +1780,7 @@ static const struct net_device_ops veth_netdev_ops = {
 	.ndo_bpf		= veth_xdp,
 	.ndo_xdp_xmit		= veth_ndo_xdp_xmit,
 	.ndo_get_peer_dev	= veth_peer_dev,
+	.ndo_tx_timeout		= veth_tx_timeout,
 };
 
 static const struct xdp_metadata_ops veth_xdp_metadata_ops = {
@@ -1803,6 +1820,7 @@ static void veth_setup(struct net_device *dev)
 	dev->priv_destructor = veth_dev_free;
 	dev->pcpu_stat_type = NETDEV_PCPU_STAT_TSTATS;
 	dev->max_mtu = ETH_MAX_MTU;
+	dev->watchdog_timeo = msecs_to_jiffies(16000);
 
 	dev->hw_features = VETH_FEATURES;
 	dev->hw_enc_features = VETH_FEATURES;
-- 
2.43.0


  parent reply	other threads:[~2026-03-24 17:48 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-03-24 17:46 [PATCH net-next 0/5] veth: add Byte Queue Limits (BQL) support hawk
2026-03-24 17:46 ` [PATCH " hawk
2026-03-24 17:56   ` Jesper Dangaard Brouer
2026-03-24 17:47 ` [PATCH net-next 1/5] net: add dev->bql flag to allow BQL sysfs for IFF_NO_QUEUE devices hawk
2026-03-24 17:47 ` [PATCH net-next 2/5] veth: implement Byte Queue Limits (BQL) for latency reduction hawk
2026-03-24 17:47 ` hawk [this message]
2026-03-24 17:47 ` [PATCH net-next 4/5] net: sched: add timeout count to NETDEV WATCHDOG message hawk
2026-03-24 17:47 ` [PATCH net-next 5/5] selftests: net: add veth BQL stress test hawk
2026-03-26 12:19   ` Jesper Dangaard Brouer

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260324174719.1224337-5-hawk@kernel.org \
    --to=hawk@kernel.org \
    --cc=andrew+netdev@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=edumazet@google.com \
    --cc=horms@kernel.org \
    --cc=j.koeppeler@tu-berlin.de \
    --cc=jhs@mojatatu.com \
    --cc=jiri@resnulli.us \
    --cc=kernel-team@cloudflare.com \
    --cc=kuba@kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=pabeni@redhat.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox