[PATCH v6] riscv: dts: spacemit: Add ethernet device for K3

[PATCH v6] riscv: dts: spacemit: Add ethernet device for K3

[Inochi Amaoto]

Add all ethernet device nodes for K3 SoC.

Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
---
Require the following patch series:
1. Basic DT device patch
https://lore.kernel.org/spacemit/20260304-01-dts-uart-full-v1-0-50a0aa53a245@kernel.org
2. Ethernet driver patch
https://lore.kernel.org/spacemit/20260316010041.164360-1-inochiama@gmail.com

Changed from v5:
1. Fix DT warning cause by stmmac-axi-config.

Changed from v4:
1. Fix pinctrl pin name
2. Remove alias for disabled node

Changed from v3:
1. Separate the pin as RGMII pin and INT pin.
2. Add comment for pin usage.
3. Rename the ethernet pinctrl node to address it is RGMII node.

Changed from v2:
1. keep aliases in alphabetical order.

Changed from v1:
1. remove interrupt-parents property
2. add aliases for ethernet node
---
 arch/riscv/boot/dts/spacemit/k3-pico-itx.dts |  20 ++++
 arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi |  34 ++++++
 arch/riscv/boot/dts/spacemit/k3.dtsi         | 117 +++++++++++++++++++
 3 files changed, 171 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
index b098dbd0e7a1..504fe6bd46b2 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
@@ -3,6 +3,7 @@
  * Copyright (c) 2026 SpacemiT (Hangzhou) Technology Co. Ltd
  * Copyright (c) 2026 Guodong Xu <guodong@riscstar.com>
  */
+#include <dt-bindings/gpio/gpio.h>

 #include "k3.dtsi"
 #include "k3-pinctrl.dtsi"
@@ -12,6 +13,7 @@ / {
 	compatible = "spacemit,k3-pico-itx", "spacemit,k3";

 	aliases {
+		ethernet0 = &eth0;
 		serial0 = &uart0;
 	};

@@ -25,6 +27,24 @@ memory@100000000 {
 	};
 };

+&eth0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_rgmii_0_cfg>, <&gmac0_phy_0_cfg>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	mdio {
+		phy0: phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			reset-gpios = <&gpio 0 15 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+		};
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_0_cfg>;
diff --git a/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi b/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi
index efb0f1572188..a7b5d10c332e 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3-pinctrl.dtsi
@@ -11,6 +11,40 @@
 #define K3_GPIO(x)	(x / 32) (x % 32)

 &pinctrl {
+	gmac0_rgmii_0_cfg: gmac0-rgmii-0-cfg {
+		gmac0-rgmii-0-pins {
+			pinmux = <K3_PADCONF(0, 1)>,	/* gmac0_rxdv */
+				 <K3_PADCONF(1, 1)>,	/* gmac0_rx_d0 */
+				 <K3_PADCONF(2, 1)>,	/* gmac0_rx_d1 */
+				 <K3_PADCONF(3, 1)>,	/* gmac0_rx_clk */
+				 <K3_PADCONF(4, 1)>,	/* gmac0_rx_d2 */
+				 <K3_PADCONF(5, 1)>,	/* gmac0_rx_d3 */
+				 <K3_PADCONF(6, 1)>,	/* gmac0_tx_d0 */
+				 <K3_PADCONF(7, 1)>,	/* gmac0_tx_d1 */
+				 <K3_PADCONF(8, 1)>,	/* gmac0_tx_clk */
+				 <K3_PADCONF(9, 1)>,	/* gmac0_tx_d2 */
+				 <K3_PADCONF(10, 1)>,	/* gmac0_tx_d3 */
+				 <K3_PADCONF(11, 1)>,	/* gmac0_tx_en */
+				 <K3_PADCONF(12, 1)>,	/* gmac0_mdc */
+				 <K3_PADCONF(13, 1)>;	/* gmac0_mdio */
+
+			bias-disable;
+			drive-strength = <25>;
+			power-source = <1800>;
+		};
+
+	};
+
+	gmac0_phy_0_cfg: gmac0-phy-0-cfg {
+		gmac0-phy-0-pins {
+			pinmux = <K3_PADCONF(14, 1)>;   /* gmac0_int */
+
+			bias-disable;
+			drive-strength = <25>;
+			power-source = <1800>;
+		};
+	};
+
 	/omit-if-no-ref/
 	uart0_0_cfg: uart0-0-cfg {
 		uart0-0-pins {
diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
index a3a8ceddabec..5f4818cd5d6d 100644
--- a/arch/riscv/boot/dts/spacemit/k3.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
@@ -438,6 +438,123 @@ soc: soc {
 		dma-noncoherent;
 		ranges;

+		eth0: ethernet@cac80000 {
+			compatible = "spacemit,k3-dwmac", "snps,dwmac-5.40a";
+			reg = <0x0 0xcac80000 0x0 0x2000>;
+			clocks = <&syscon_apmu CLK_APMU_EMAC0_BUS>,
+				 <&syscon_apmu CLK_APMU_EMAC0_1588>,
+				 <&syscon_apmu CLK_APMU_EMAC0_RGMII_TX>;
+			clock-names = "stmmaceth", "ptp_ref", "tx";
+			interrupts = <131 IRQ_TYPE_LEVEL_HIGH>,
+				     <276 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_wake_irq";
+			resets = <&syscon_apmu RESET_APMU_EMAC0>;
+			reset-names = "stmmaceth";
+			rx-fifo-depth = <8192>;
+			tx-fifo-depth = <8192>;
+			snps,multicast-filter-bins = <64>;
+			snps,perfect-filter-entries = <32>;
+			snps,aal;
+			snps,tso;
+			snps,txpbl = <8>;
+			snps,rxpbl = <8>;
+			snps,force_sf_dma_mode;
+			snps,axi-config = <&gmac0_axi_setup>;
+			spacemit,apmu = <&syscon_apmu 0x3e4 0x3e8>;
+			status = "disabled";
+
+			mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			gmac0_axi_setup: stmmac-axi-config {
+				snps,wr_osr_lmt = <0xf>;
+				snps,rd_osr_lmt = <0xf>;
+				/* max axi burst len is 256 */
+				snps,blen = <256 128 64 32 16 0 0>;
+			};
+		};
+
+		eth1: ethernet@cac82000 {
+			compatible = "spacemit,k3-dwmac", "snps,dwmac-5.40a";
+			reg = <0x0 0xcac82000 0x0 0x2000>;
+			clocks = <&syscon_apmu CLK_APMU_EMAC1_BUS>,
+				 <&syscon_apmu CLK_APMU_EMAC1_1588>,
+				 <&syscon_apmu CLK_APMU_EMAC1_RGMII_TX>;
+			clock-names = "stmmaceth", "ptp_ref", "tx";
+			interrupts = <133 IRQ_TYPE_LEVEL_HIGH>,
+				     <277 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_wake_irq";
+			resets = <&syscon_apmu RESET_APMU_EMAC1>;
+			reset-names = "stmmaceth";
+			rx-fifo-depth = <8192>;
+			tx-fifo-depth = <8192>;
+			snps,multicast-filter-bins = <64>;
+			snps,perfect-filter-entries = <32>;
+			snps,aal;
+			snps,tso;
+			snps,txpbl = <8>;
+			snps,rxpbl = <8>;
+			snps,force_sf_dma_mode;
+			snps,axi-config = <&gmac1_axi_setup>;
+			spacemit,apmu = <&syscon_apmu 0x3ec 0x3f0>;
+			status = "disabled";
+
+			mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			gmac1_axi_setup: stmmac-axi-config {
+				snps,wr_osr_lmt = <0xf>;
+				snps,rd_osr_lmt = <0xf>;
+				/* max axi burst len is 256 */
+				snps,blen = <256 128 64 32 16 0 0>;
+			};
+		};
+
+		eth2: ethernet@cac8e000 {
+			compatible = "spacemit,k3-dwmac", "snps,dwmac-5.40a";
+			reg = <0x0 0xcac8e000 0x0 0x2000>;
+			clocks = <&syscon_apmu CLK_APMU_EMAC2_BUS>,
+				 <&syscon_apmu CLK_APMU_EMAC2_1588>,
+				 <&syscon_apmu CLK_APMU_EMAC2_RGMII_TX>;
+			clock-names = "stmmaceth", "ptp_ref", "tx";
+			interrupts = <130 IRQ_TYPE_LEVEL_HIGH>,
+				     <278 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_wake_irq";
+			resets = <&syscon_apmu RESET_APMU_EMAC2>;
+			reset-names = "stmmaceth";
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <4096>;
+			snps,multicast-filter-bins = <64>;
+			snps,perfect-filter-entries = <32>;
+			snps,aal;
+			snps,tso;
+			snps,txpbl = <8>;
+			snps,rxpbl = <8>;
+			snps,force_sf_dma_mode;
+			snps,axi-config = <&gmac2_axi_setup>;
+			spacemit,apmu = <&syscon_apmu 0x248 0x24c>;
+			status = "disabled";
+
+			mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			gmac2_axi_setup: stmmac-axi-config {
+				snps,wr_osr_lmt = <0xf>;
+				snps,rd_osr_lmt = <0xf>;
+				/* max axi burst len is 256 */
+				snps,blen = <256 128 64 32 16 0 0>;
+			};
+		};
+
 		syscon_apbc: system-controller@d4015000 {
 			compatible = "spacemit,k3-syscon-apbc";
 			reg = <0x0 0xd4015000 0x0 0x1000>;
--
2.53.0

Re: [PATCH v6] riscv: dts: spacemit: Add ethernet device for K3

[Yixun Lan]

Hi Inochi,

On 09:46 Thu 26 Mar     , Inochi Amaoto wrote:
> Add all ethernet device nodes for K3 SoC.
> 
> Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
> ---
> Require the following patch series:
> 1. Basic DT device patch
> https://lore.kernel.org/spacemit/20260304-01-dts-uart-full-v1-0-50a0aa53a245@kernel.org
> 2. Ethernet driver patch
> https://lore.kernel.org/spacemit/20260316010041.164360-1-inochiama@gmail.com
> 
> Changed from v5:
> 1. Fix DT warning cause by stmmac-axi-config.
> 

It would be great to let people know explicitly that you dropped the tag
they gave, but I can understand you wanna be cautious here, so again

Reviewed-by: Yixun Lan <dlan@kernel.org>

-- 
Yixun Lan (dlan)