[PATCH v2] net: phy: air_en8811h: add AN8811HB MCU assert/deassert support

["Lucien.Jheng" <lucienzx159@gmail.com>]

AN8811HB needs a MCU soft-reset cycle before firmware loading begins.
Assert the MCU (hold it in reset) and immediately deassert (release)
via a dedicated PBUS register pair (0x5cf9f8 / 0x5cf9fc), accessed
through the PHY-addr+8 MDIO bus node rather than the BUCKPBUS indirect
path.  This clears the MCU state before the firmware loading sequence
starts.

Add __air_pbus_reg_write() as a low-level helper for this access, then
implement an8811hb_mcu_assert() / _deassert() on top of it.  Wire both
into an8811hb_load_firmware() and en8811h_restart_mcu() so every
firmware load or MCU restart on AN8811HB correctly sequences the reset
control registers.

Fixes: 0a55766b7711 ("net: phy: air_en8811h: add Airoha AN8811HB support")
Signed-off-by: Lucien Jheng <lucienzx159@gmail.com>
---
Changes in v2:
- Rewrite commit message: The previous wording was ambiguous,
  as it suggested the MCU remains asserted during the entire
  firmware loading process, rather than a quick reset cycle
  before it starts.
  Clarify that assert and deassert is an immediate soft-reset
  cycle to clear MCU state before firmware loading begins.
- Add Fixes: 0a55766b7711 ("net: phy: air_en8811h: add Airoha AN8811HB
  support").
- Change phydev_info() to phydev_dbg() in an8811hb_mcu_assert() and
  an8811hb_mcu_deassert() to avoid noise during normal boot.

 drivers/net/phy/air_en8811h.c | 105 ++++++++++++++++++++++++++++++++++
 1 file changed, 105 insertions(+)

diff --git a/drivers/net/phy/air_en8811h.c b/drivers/net/phy/air_en8811h.c
index 29ae73e65caa..01fce1b93618 100644
--- a/drivers/net/phy/air_en8811h.c
+++ b/drivers/net/phy/air_en8811h.c
@@ -170,6 +170,16 @@
 #define   AN8811HB_CLK_DRV_CKO_LDPWD		BIT(13)
 #define   AN8811HB_CLK_DRV_CKO_LPPWD		BIT(14)

+#define AN8811HB_MCU_SW_RST		0x5cf9f8
+#define   AN8811HB_MCU_SW_RST_HOLD		BIT(16)
+#define   AN8811HB_MCU_SW_RST_RUN		(BIT(16) | BIT(0))
+#define AN8811HB_MCU_SW_START		0x5cf9fc
+#define   AN8811HB_MCU_SW_START_EN		BIT(16)
+
+/* MII register constants for PBUS access (PHY addr + 8) */
+#define AIR_PBUS_ADDR_HIGH		0x1c
+#define AIR_PBUS_DATA_HIGH		0x10
+
 /* Led definitions */
 #define EN8811H_LED_COUNT	3

@@ -254,6 +264,36 @@ static int air_phy_write_page(struct phy_device *phydev, int page)
 	return __phy_write(phydev, AIR_EXT_PAGE_ACCESS, page);
 }

+static int __air_pbus_reg_write(struct phy_device *phydev,
+				u32 pbus_reg, u32 pbus_data)
+{
+	struct mii_bus *bus = phydev->mdio.bus;
+	int pbus_addr = phydev->mdio.addr + 8;
+	int ret;
+
+	ret = __mdiobus_write(bus, pbus_addr, AIR_EXT_PAGE_ACCESS,
+			      upper_16_bits(pbus_reg));
+	if (ret < 0)
+		return ret;
+
+	ret = __mdiobus_write(bus, pbus_addr, AIR_PBUS_ADDR_HIGH,
+			      (pbus_reg & GENMASK(15, 6)) >> 6);
+	if (ret < 0)
+		return ret;
+
+	ret = __mdiobus_write(bus, pbus_addr, (pbus_reg & GENMASK(5, 2)) >> 2,
+			      lower_16_bits(pbus_data));
+	if (ret < 0)
+		return ret;
+
+	ret = __mdiobus_write(bus, pbus_addr, AIR_PBUS_DATA_HIGH,
+			      upper_16_bits(pbus_data));
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
 static int __air_buckpbus_reg_write(struct phy_device *phydev,
 				    u32 pbus_address, u32 pbus_data)
 {
@@ -570,10 +610,65 @@ static int an8811hb_load_file(struct phy_device *phydev, const char *name,
 	return ret;
 }

+static int an8811hb_mcu_assert(struct phy_device *phydev)
+{
+	int ret;
+
+	phy_lock_mdio_bus(phydev);
+
+	ret = __air_pbus_reg_write(phydev, AN8811HB_MCU_SW_RST,
+				   AN8811HB_MCU_SW_RST_HOLD);
+	if (ret < 0)
+		goto unlock;
+
+	ret = __air_pbus_reg_write(phydev, AN8811HB_MCU_SW_START, 0);
+	if (ret < 0)
+		goto unlock;
+
+	msleep(50);
+	phydev_dbg(phydev, "MCU asserted\n");
+
+unlock:
+	phy_unlock_mdio_bus(phydev);
+	return ret;
+}
+
+static int an8811hb_mcu_deassert(struct phy_device *phydev)
+{
+	int ret;
+
+	phy_lock_mdio_bus(phydev);
+
+	ret = __air_pbus_reg_write(phydev, AN8811HB_MCU_SW_START,
+				   AN8811HB_MCU_SW_START_EN);
+	if (ret < 0)
+		goto unlock;
+
+	ret = __air_pbus_reg_write(phydev, AN8811HB_MCU_SW_RST,
+				   AN8811HB_MCU_SW_RST_RUN);
+	if (ret < 0)
+		goto unlock;
+
+	msleep(50);
+	phydev_dbg(phydev, "MCU deasserted\n");
+
+unlock:
+	phy_unlock_mdio_bus(phydev);
+	return ret;
+}
+
 static int an8811hb_load_firmware(struct phy_device *phydev)
 {
 	int ret;

+	ret = an8811hb_mcu_assert(phydev);
+	if (ret < 0)
+		return ret;
+
+	ret = an8811hb_mcu_deassert(phydev);
+	if (ret < 0)
+		return ret;
+
 	ret = air_buckpbus_reg_write(phydev, EN8811H_FW_CTRL_1,
 				     EN8811H_FW_CTRL_1_START);
 	if (ret < 0)
@@ -662,6 +757,16 @@ static int en8811h_restart_mcu(struct phy_device *phydev)
 {
 	int ret;

+	if (phy_id_compare_model(phydev->phy_id, AN8811HB_PHY_ID)) {
+		ret = an8811hb_mcu_assert(phydev);
+		if (ret < 0)
+			return ret;
+
+		ret = an8811hb_mcu_deassert(phydev);
+		if (ret < 0)
+			return ret;
+	}
+
 	ret = air_buckpbus_reg_write(phydev, EN8811H_FW_CTRL_1,
 				     EN8811H_FW_CTRL_1_START);
 	if (ret < 0)
--
2.34.1