Netdev List
 help / color / mirror / Atom feed
From: Vineeth Karumanchi <vineeth.karumanchi@amd.com>
To: <theo.lebrun@bootlin.com>, <conor.dooley@microchip.com>,
	<andrew+netdev@lunn.ch>, <davem@davemloft.net>,
	<edumazet@google.com>, <kuba@kernel.org>, <pabeni@redhat.com>
Cc: <vineeth.karumanchi@amd.com>, <git@amd.com>,
	<netdev@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: [PATCH net-next 2/2] net: macb: configure ENST registers for all queues
Date: Fri, 24 Jul 2026 10:02:57 +0530	[thread overview]
Message-ID: <20260724043257.2221030-3-vineeth.karumanchi@amd.com> (raw)
In-Reply-To: <20260724043257.2221030-1-vineeth.karumanchi@amd.com>

The initial "tc" command was not overwriting the reset value of ENST
registers if only a subset of queues were configured, leading to an
invalid setup. To fix this, configure all queues unconditionally.
Unconfigured queues are zero-initialized via kcalloc(), ensuring a
complete and consistent configuration.

The queue_id field in struct macb_queue_enst_config becomes redundant
once the array is indexed by queue id, so drop it.

Key changes:
- Drop queue_id from struct macb_queue_enst_config
- Allocate enst_queue[] based on bp->num_queues instead of
  conf->num_entries
- Index enst_queue[] directly with the queue number
- Program ENST registers for all queues

Fixes: 89934dbf169e ("net: macb: Add TAPRIO traffic scheduling support")
Signed-off-by: Vineeth Karumanchi <vineeth.karumanchi@amd.com>
---
 drivers/net/ethernet/cadence/macb.h      |  2 --
 drivers/net/ethernet/cadence/macb_main.c | 20 +++++++++-----------
 2 files changed, 9 insertions(+), 13 deletions(-)

diff --git a/drivers/net/ethernet/cadence/macb.h b/drivers/net/ethernet/cadence/macb.h
index a11052565436..4cc9aa9b2f9e 100644
--- a/drivers/net/ethernet/cadence/macb.h
+++ b/drivers/net/ethernet/cadence/macb.h
@@ -1490,7 +1490,6 @@ struct macb_platform_data {
  * @start_time_mask:  Bitmask representing the start time for the queue
  * @on_time_bytes:    "on" time nsec expressed in bytes
  * @off_time_bytes:   "off" time nsec expressed in bytes
- * @queue_id:         Identifier for the queue
  *
  * This structure holds the configuration parameters for an ENST queue,
  * used to control time-based transmission scheduling in the MACB driver.
@@ -1499,7 +1498,6 @@ struct macb_queue_enst_config {
 	u32 start_time_mask;
 	u32 on_time_bytes;
 	u32 off_time_bytes;
-	u8 queue_id;
 };
 
 #endif /* _MACB_H */
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index d394f1f43b68..d58430fe9c41 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -4329,7 +4329,7 @@ static int macb_taprio_setup_replace(struct net_device *ndev,
 	struct macb_queue *queue;
 	u32 queue_mask;
 	u8 queue_id;
-	size_t i;
+	size_t i, q;
 	int err;
 
 	if (conf->num_entries > bp->num_queues) {
@@ -4357,7 +4357,7 @@ static int macb_taprio_setup_replace(struct net_device *ndev,
 		return -EINVAL;
 	}
 
-	enst_queue = kcalloc(conf->num_entries, sizeof(*enst_queue), GFP_KERNEL);
+	enst_queue = kcalloc(bp->num_queues, sizeof(*enst_queue), GFP_KERNEL);
 	if (unlikely(!enst_queue))
 		return -ENOMEM;
 
@@ -4416,13 +4416,12 @@ static int macb_taprio_setup_replace(struct net_device *ndev,
 			goto cleanup;
 		}
 
-		enst_queue[i].queue_id = queue_id;
-		enst_queue[i].start_time_mask =
+		enst_queue[queue_id].start_time_mask =
 			(start_time_sec << GEM_START_TIME_SEC_OFFSET) |
 			start_time_nsec;
-		enst_queue[i].on_time_bytes =
+		enst_queue[queue_id].on_time_bytes =
 			enst_ns_to_hw_units(entry->interval, speed);
-		enst_queue[i].off_time_bytes =
+		enst_queue[queue_id].off_time_bytes =
 			enst_ns_to_hw_units(conf->cycle_time - entry->interval, speed);
 
 		configured_queues |= entry->gate_mask;
@@ -4448,15 +4447,14 @@ static int macb_taprio_setup_replace(struct net_device *ndev,
 		gem_writel(bp, ENST_CONTROL,
 			   queue_mask << GEM_ENST_DISABLE_QUEUE_OFFSET);
 
-		for (i = 0; i < conf->num_entries; i++) {
-			queue = &bp->queues[enst_queue[i].queue_id];
+		for (q = 0, queue = bp->queues; q < bp->num_queues; ++q, ++queue) {
 			/* Configure queue timing registers */
 			queue_writel(queue, ENST_START_TIME,
-				     enst_queue[i].start_time_mask);
+				     enst_queue[q].start_time_mask);
 			queue_writel(queue, ENST_ON_TIME,
-				     enst_queue[i].on_time_bytes);
+				     enst_queue[q].on_time_bytes);
 			queue_writel(queue, ENST_OFF_TIME,
-				     enst_queue[i].off_time_bytes);
+				     enst_queue[q].off_time_bytes);
 		}
 
 		/* Enable ENST for all configured queues in one write */
-- 
2.44.4


  parent reply	other threads:[~2026-07-24  4:33 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-07-24  4:32 [PATCH net-next 0/2] net: macb: fix ENST configuration for all queues Vineeth Karumanchi
2026-07-24  4:32 ` [PATCH net-next 1/2] net: macb: remove unused ENST Q0/Q1 time register defines Vineeth Karumanchi
2026-07-24 17:49   ` Théo Lebrun
2026-07-24 19:40   ` Nicolai Buchwitz
2026-07-24  4:32 ` Vineeth Karumanchi [this message]
2026-07-24 18:06   ` [PATCH net-next 2/2] net: macb: configure ENST registers for all queues Théo Lebrun
2026-07-24 19:57   ` Nicolai Buchwitz

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260724043257.2221030-3-vineeth.karumanchi@amd.com \
    --to=vineeth.karumanchi@amd.com \
    --cc=andrew+netdev@lunn.ch \
    --cc=conor.dooley@microchip.com \
    --cc=davem@davemloft.net \
    --cc=edumazet@google.com \
    --cc=git@amd.com \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=pabeni@redhat.com \
    --cc=theo.lebrun@bootlin.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox