From: Jerome Brunet <jbrunet@baylibre.com>
To: Andrew Lunn <andrew+netdev@lunn.ch>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>,
Paolo Abeni <pabeni@redhat.com>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Chen-Yu Tsai <wens@kernel.org>,
Jernej Skrabec <jernej.skrabec@gmail.com>,
Samuel Holland <samuel@sholland.org>,
Richard Cochran <richardcochran@gmail.com>,
Maxime Ripard <mripard@kernel.org>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Alexandre Torgue <alexandre.torgue@foss.st.com>,
Philipp Zabel <p.zabel@pengutronix.de>,
Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: netdev@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-sunxi@lists.linux.dev, linux-kernel@vger.kernel.org,
linux-stm32@st-md-mailman.stormreply.com,
Andre Przywara <andre.przywara@arm.com>,
Jerome Brunet <jbrunet@baylibre.com>
Subject: [PATCH net-next v3 2/5] net: stmmac: sun55i: Add per-compatible match data
Date: Wed, 23 Sep 2026 22:47:32 +0200 [thread overview]
Message-ID: <20260923-allwinner-a733-gmac-support-v3-2-15735155a789@baylibre.com> (raw)
In-Reply-To: <20260923-allwinner-a733-gmac-support-v3-0-15735155a789@baylibre.com>
The A733 GMAC210 glue registers are in a dedicated MMIO region of the
controller rather than in a syscon, at a different offset.
Add per-compatible match data holding the glue resource init callback, the
stmmac flags and the glue register offset to prepare the support for the
A733.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
drivers/net/ethernet/stmicro/stmmac/dwmac-sun55i.c | 68 +++++++++++++++++-----
1 file changed, 54 insertions(+), 14 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun55i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun55i.c
index 862df173d963..c4df53285007 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun55i.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun55i.c
@@ -16,6 +16,7 @@
#include <linux/of.h>
#include <linux/phy.h>
#include <linux/platform_device.h>
+#include <linux/property.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
#include <linux/stmmac.h>
@@ -23,8 +24,6 @@
#include "stmmac.h"
#include "stmmac_platform.h"
-#define SYSCON_REG 0x34
-
/* RMII specific bits */
#define SYSCON_RMII_EN BIT(13) /* 1: enable RMII (overrides EPIT) */
/* Generic system control EMAC_CLK bits */
@@ -37,18 +36,40 @@
#define SYSCON_ETCS_EXT_GMII 0x1
#define SYSCON_ETCS_INT_GMII 0x2
-static int sun55i_gmac200_set_syscon(struct device *dev,
- struct plat_stmmacenet_data *plat)
+struct sun55i_gmac;
+
+struct sun55i_gmac_data {
+ int (*init_resources)(struct platform_device *pdev,
+ struct sun55i_gmac *gmac);
+ unsigned int flags;
+ u32 offset;
+};
+
+struct sun55i_gmac {
+ const struct sun55i_gmac_data *data;
+ struct regmap *regmap;
+};
+
+static int sun55i_gmac200_init_resources(struct platform_device *pdev,
+ struct sun55i_gmac *gmac)
+{
+ gmac->regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+ "syscon");
+ if (IS_ERR(gmac->regmap))
+ return dev_err_probe(&pdev->dev, PTR_ERR(gmac->regmap),
+ "Unable to map syscon\n");
+
+ return 0;
+}
+
+static int sun55i_gmac200_setup(struct device *dev,
+ struct plat_stmmacenet_data *plat,
+ const struct sun55i_gmac *gmac)
{
struct device_node *node = dev->of_node;
- struct regmap *regmap;
u32 val, reg = 0;
int ret;
- regmap = syscon_regmap_lookup_by_phandle(node, "syscon");
- if (IS_ERR(regmap))
- return dev_err_probe(dev, PTR_ERR(regmap), "Unable to map syscon\n");
-
if (!of_property_read_u32(node, "tx-internal-delay-ps", &val)) {
if (val % 100)
return dev_err_probe(dev, -EINVAL,
@@ -95,7 +116,7 @@ static int sun55i_gmac200_set_syscon(struct device *dev,
phy_modes(plat->phy_interface));
}
- ret = regmap_write(regmap, SYSCON_REG, reg);
+ ret = regmap_write(gmac->regmap, gmac->data->offset, reg);
if (ret < 0)
return dev_err_probe(dev, ret, "Failed to write to syscon\n");
@@ -107,22 +128,34 @@ static int sun55i_gmac200_probe(struct platform_device *pdev)
struct plat_stmmacenet_data *plat_dat;
struct stmmac_resources stmmac_res;
struct device *dev = &pdev->dev;
+ struct sun55i_gmac *gmac;
struct clk *clk;
int ret;
+ gmac = devm_kzalloc(dev, sizeof(*gmac), GFP_KERNEL);
+ if (!gmac)
+ return -ENOMEM;
+
+ gmac->data = device_get_match_data(dev);
+ if (!gmac->data)
+ return -EINVAL;
+
ret = stmmac_get_platform_resources(pdev, &stmmac_res);
if (ret)
return ret;
+ ret = gmac->data->init_resources(pdev, gmac);
+ if (ret)
+ return ret;
+
plat_dat = devm_stmmac_probe_config_dt(pdev, stmmac_res.mac);
if (IS_ERR(plat_dat))
return PTR_ERR(plat_dat);
- /* BSP disables it */
- plat_dat->flags |= STMMAC_FLAG_SPH_DISABLE;
+ plat_dat->flags |= gmac->data->flags;
plat_dat->host_dma_width = 32;
- ret = sun55i_gmac200_set_syscon(dev, plat_dat);
+ ret = sun55i_gmac200_setup(dev, plat_dat, gmac);
if (ret)
return ret;
@@ -138,8 +171,15 @@ static int sun55i_gmac200_probe(struct platform_device *pdev)
return devm_stmmac_pltfr_probe(pdev, plat_dat, &stmmac_res);
}
+static const struct sun55i_gmac_data sun55i_a523_gmac200_data = {
+ .init_resources = sun55i_gmac200_init_resources,
+ .flags = STMMAC_FLAG_SPH_DISABLE,
+ .offset = 0x34,
+};
+
static const struct of_device_id sun55i_gmac200_match[] = {
- { .compatible = "allwinner,sun55i-a523-gmac200" },
+ { .compatible = "allwinner,sun55i-a523-gmac200",
+ .data = &sun55i_a523_gmac200_data },
{ }
};
MODULE_DEVICE_TABLE(of, sun55i_gmac200_match);
--
2.53.0
next prev parent reply other threads:[~2026-09-23 20:47 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-23 20:47 [PATCH net-next v3 0/5] net: stmmac: Add support for Allwinner A733 GMAC210 Jerome Brunet
2026-09-23 20:47 ` [PATCH net-next v3 1/5] dt-bindings: net: sun8i-emac: Add A733 GMAC210 compatible Jerome Brunet
2026-09-23 20:47 ` Jerome Brunet [this message]
2026-09-23 20:47 ` [PATCH net-next v3 3/5] net: stmmac: sun55i: Make the delay step configurable Jerome Brunet
2026-09-24 2:30 ` Andrew Lunn
2026-09-24 8:53 ` Jerome Brunet
2026-09-24 12:55 ` Andrew Lunn
2026-09-23 20:47 ` [PATCH net-next v3 4/5] net: stmmac: sun55i: Support TX delay extension bits Jerome Brunet
2026-09-23 20:47 ` [PATCH net-next v3 5/5] net: stmmac: sun55i: Add support for Allwinner A733 GMAC210 Jerome Brunet
2026-09-23 22:15 ` [PATCH net-next v3 0/5] net: stmmac: " Andrew Lunn
2026-09-23 22:19 ` Andrew Lunn
2026-09-24 8:40 ` Jerome Brunet
2026-09-24 12:54 ` Andrew Lunn
2026-09-24 15:27 ` Jerome Brunet
2026-09-24 16:02 ` Andrew Lunn
2026-09-25 8:26 ` Jerome Brunet
2026-09-25 19:45 ` Andrew Lunn
2026-09-29 15:06 ` Jerome Brunet
2026-09-29 16:10 ` Andrew Lunn
2026-09-29 17:15 ` Jerome Brunet
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260923-allwinner-a733-gmac-support-v3-2-15735155a789@baylibre.com \
--to=jbrunet@baylibre.com \
--cc=alexandre.torgue@foss.st.com \
--cc=andre.przywara@arm.com \
--cc=andrew+netdev@lunn.ch \
--cc=conor+dt@kernel.org \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=edumazet@google.com \
--cc=jernej.skrabec@gmail.com \
--cc=krzk+dt@kernel.org \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=linux-sunxi@lists.linux.dev \
--cc=maxime.chevallier@bootlin.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=mripard@kernel.org \
--cc=netdev@vger.kernel.org \
--cc=p.zabel@pengutronix.de \
--cc=pabeni@redhat.com \
--cc=richardcochran@gmail.com \
--cc=robh@kernel.org \
--cc=samuel@sholland.org \
--cc=wens@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox