Netdev List
 help / color / mirror / Atom feed
From: Daniel Machon <daniel.machon@microchip.com>
To: Andrew Lunn <andrew+netdev@lunn.ch>,
	"David S. Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@google.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	Horatiu Vultur <horatiu.vultur@microchip.com>,
	Steen Hegelund <steen.hegelund@microchip.com>,
	<UNGLinuxDriver@microchip.com>,
	"Alexei Starovoitov" <ast@kernel.org>,
	Daniel Borkmann <daniel@iogearbox.net>,
	"Jesper Dangaard Brouer" <hawk@kernel.org>,
	John Fastabend <john.fastabend@gmail.com>,
	Stanislav Fomichev <sdf@fomichev.me>,
	Herve Codina <herve.codina@bootlin.com>,
	Arnd Bergmann <arnd@arndb.de>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Mohsin Bashir <mohsin.bashr@gmail.com>,
	"Simon Horman" <horms@kernel.org>
Cc: Richard Cochran <richardcochran@gmail.com>,
	<netdev@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<bpf@vger.kernel.org>, <linux-arm-kernel@lists.infradead.org>
Subject: [PATCH net-next v9 10/15] net: lan966x: add shutdown callback to stop the FDMA on reboot
Date: Mon, 28 Sep 2026 21:32:58 +0200	[thread overview]
Message-ID: <20260928-lan966x-pci-fdma-v9-10-a17caf60f89a@microchip.com> (raw)
In-Reply-To: <20260928-lan966x-pci-fdma-v9-0-a17caf60f89a@microchip.com>

As a PCIe endpoint, lan966x is not reset by a host reboot: its FDMA
channels and interrupt sources stay armed, and the OIC ORs every
source into the shared PCIe INTx, asserted before the driver has
re-probed. A still-active channel also keeps write access to host
memory the next kernel will reuse.

Add a shutdown callback that:
- frees the ana, xtr and FDMA irqs, masking and unmapping them at
  the OIC (disable_irq() would leave both set - the OIC has no
  irq_disable())
- masks the analyzer source, armed unconditionally by lan966x_init()
  and re-armed by the MAC table's age timer
- stops and detaches the netdevs, draining in-flight xmit and
  clearing netif_device_present() so ndo_open/ndo_change_mtu cannot
  re-enter the FDMA against a disabled NAPI
- disables both FDMA channels and masks their interrupts
- unmaps the outbound ATU windows, leaving none armed (the windows
  are mapped by the PCIe FDMA backend added later in this series)

NAPI is skipped when fdma_ndev is unset (a probed switch with no
usable port never adds one), and XDP attach cannot re-enter the FDMA
either: on PCIe, lan966x_xdp_setup() returns before the page pool
reload, which is the only point where it touches the FDMA.

Only the PCIe instantiation needs this - the SoC one resets with the
chip - so the callback returns early on a platform device; the check
is at runtime since .shutdown belongs to the driver, and a
PCIe-enabled kernel binds both.

FDMA_INTR_ENA persists across a warm reboot, so also restore the
full enable in lan966x_fdma_rx_start(), run after both rings are
allocated. The PCIe FDMA backend added later in this series starts
RX through the same function, so both backends are re-armed from
one site.

Tested-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
---
 .../net/ethernet/microchip/lan966x/lan966x_fdma.c  |  4 ++
 .../net/ethernet/microchip/lan966x/lan966x_main.c  | 56 ++++++++++++++++++++++
 .../net/ethernet/microchip/lan966x/lan966x_regs.h  | 15 ++++++
 3 files changed, 75 insertions(+)

diff --git a/drivers/net/ethernet/microchip/lan966x/lan966x_fdma.c b/drivers/net/ethernet/microchip/lan966x/lan966x_fdma.c
index 5f46166cbfe4..2e8f786d6fee 100644
--- a/drivers/net/ethernet/microchip/lan966x/lan966x_fdma.c
+++ b/drivers/net/ethernet/microchip/lan966x/lan966x_fdma.c
@@ -146,6 +146,10 @@ void lan966x_fdma_rx_start(struct lan966x_rx *rx)
 	struct fdma *fdma = &rx->fdma;
 	u32 mask;
 
+	lan_wr(FDMA_INTR_ENA_INTR_PORT_ENA_SET(GENMASK(1, 0)) |
+	       FDMA_INTR_ENA_INTR_CH_ENA_SET(GENMASK(7, 0)),
+	       lan966x, FDMA_INTR_ENA);
+
 	lan_wr(FDMA_CH_CFG_CH_DCB_DB_CNT_SET(fdma->n_dbs) |
 	       FDMA_CH_CFG_CH_INTR_DB_EOF_ONLY_SET(1) |
 	       FDMA_CH_CFG_CH_INJ_PORT_SET(0) |
diff --git a/drivers/net/ethernet/microchip/lan966x/lan966x_main.c b/drivers/net/ethernet/microchip/lan966x/lan966x_main.c
index 259d81e75907..024ce9f9916c 100644
--- a/drivers/net/ethernet/microchip/lan966x/lan966x_main.c
+++ b/drivers/net/ethernet/microchip/lan966x/lan966x_main.c
@@ -1324,9 +1324,65 @@ static void lan966x_remove(struct platform_device *pdev)
 	debugfs_remove_recursive(lan966x->debugfs_root);
 }
 
+static void lan966x_shutdown(struct platform_device *pdev)
+{
+	struct lan966x *lan966x = platform_get_drvdata(pdev);
+
+	/* As a PCIe endpoint the switch is not reset by the host reboot, so it
+	 * has to be quiesced here:
+	 *
+	 *   Free the irqs and mask the sources: no source can assert INTx.
+	 *   Disable NAPI: the teardown must not race a poll.
+	 *   Stop and detach the netdevs: drains xmit, closes ndo_open and MTU.
+	 *   Stop the FDMA channels: waits for the engine to go idle.
+	 *   Unmap the ATU windows: revokes the engine's access to host memory.
+	 */
+	if (!lan966x_is_pci(lan966x))
+		return;
+
+	if (lan966x->xtr_irq > 0)
+		devm_free_irq(lan966x->dev, lan966x->xtr_irq, lan966x);
+	if (lan966x->ana_irq > 0)
+		devm_free_irq(lan966x->dev, lan966x->ana_irq, lan966x);
+	if (lan966x->fdma_irq > 0)
+		devm_free_irq(lan966x->dev, lan966x->fdma_irq, lan966x);
+
+	lan_wr(0, lan966x, ANA_ANAINTR);
+
+	if (!lan966x->fdma)
+		return;
+
+	rtnl_lock();
+
+	if (lan966x->fdma_ndev)
+		napi_disable(&lan966x->napi);
+
+	for (int p = 0; p < lan966x->num_phys_ports; p++) {
+		if (!lan966x->ports[p] || !lan966x->ports[p]->dev)
+			continue;
+
+		netif_tx_disable(lan966x->ports[p]->dev);
+		netif_device_detach(lan966x->ports[p]->dev);
+	}
+
+	lan966x_fdma_rx_disable(&lan966x->rx);
+	lan966x_fdma_tx_disable(&lan966x->tx);
+
+	lan_wr(0, lan966x, FDMA_INTR_ENA);
+	lan_wr(0, lan966x, FDMA_INTR_DB_ENA);
+
+#if IS_ENABLED(CONFIG_MCHP_LAN966X_PCI)
+	fdma_pci_atu_region_unmap(lan966x->rx.fdma.atu_region);
+	fdma_pci_atu_region_unmap(lan966x->tx.fdma.atu_region);
+#endif
+
+	rtnl_unlock();
+}
+
 static struct platform_driver lan966x_driver = {
 	.probe = lan966x_probe,
 	.remove = lan966x_remove,
+	.shutdown = lan966x_shutdown,
 	.driver = {
 		.name = "lan966x-switch",
 		.of_match_table = lan966x_match,
diff --git a/drivers/net/ethernet/microchip/lan966x/lan966x_regs.h b/drivers/net/ethernet/microchip/lan966x/lan966x_regs.h
index 4b553927d2e0..aba0d36ae6b5 100644
--- a/drivers/net/ethernet/microchip/lan966x/lan966x_regs.h
+++ b/drivers/net/ethernet/microchip/lan966x/lan966x_regs.h
@@ -1039,6 +1039,21 @@ enum lan966x_target {
 /*      FDMA:FDMA:FDMA_INTR_ERR */
 #define FDMA_INTR_ERR             __REG(TARGET_FDMA, 0, 1, 8, 0, 1, 428, 400, 0, 1, 4)
 
+/*      FDMA:FDMA:FDMA_INTR_ENA */
+#define FDMA_INTR_ENA             __REG(TARGET_FDMA, 0, 1, 8, 0, 1, 428, 404, 0, 1, 4)
+
+#define FDMA_INTR_ENA_INTR_PORT_ENA              GENMASK(9, 8)
+#define FDMA_INTR_ENA_INTR_PORT_ENA_SET(x)\
+	FIELD_PREP(FDMA_INTR_ENA_INTR_PORT_ENA, x)
+#define FDMA_INTR_ENA_INTR_PORT_ENA_GET(x)\
+	FIELD_GET(FDMA_INTR_ENA_INTR_PORT_ENA, x)
+
+#define FDMA_INTR_ENA_INTR_CH_ENA                GENMASK(7, 0)
+#define FDMA_INTR_ENA_INTR_CH_ENA_SET(x)\
+	FIELD_PREP(FDMA_INTR_ENA_INTR_CH_ENA, x)
+#define FDMA_INTR_ENA_INTR_CH_ENA_GET(x)\
+	FIELD_GET(FDMA_INTR_ENA_INTR_CH_ENA, x)
+
 /*      FDMA:FDMA:FDMA_ERRORS */
 #define FDMA_ERRORS               __REG(TARGET_FDMA, 0, 1, 8, 0, 1, 428, 412, 0, 1, 4)
 

-- 
2.34.1


  parent reply	other threads:[~2026-09-28 19:33 UTC|newest]

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-09-28 19:32 [PATCH net-next v9 00/15] net: lan966x: add support for PCIe FDMA Daniel Machon
2026-09-28 19:32 ` [PATCH net-next v9 01/15] MAINTAINERS: add FDMA library to Sparx5 SoC entry Daniel Machon
2026-09-28 19:32 ` [PATCH net-next v9 02/15] net: microchip: fdma: rename contiguous dataptr helpers Daniel Machon
2026-09-28 19:32 ` [PATCH net-next v9 03/15] net: microchip: fdma: add PCIe ATU support Daniel Machon
2026-10-02  7:33   ` netdev-bot+sashiko
2026-09-28 19:32 ` [PATCH net-next v9 04/15] net: microchip: fdma: use little-endian types for descriptor fields Daniel Machon
2026-10-02 13:25   ` Simon Horman
2026-09-28 19:32 ` [PATCH net-next v9 05/15] net: lan966x: add FDMA LLP register write helper Daniel Machon
2026-09-28 19:32 ` [PATCH net-next v9 06/15] net: lan966x: export FDMA helpers for reuse Daniel Machon
2026-09-28 19:32 ` [PATCH net-next v9 07/15] net: lan966x: use a dedicated device for DMA operations Daniel Machon
2026-09-28 19:32 ` [PATCH net-next v9 08/15] net: lan966x: add FDMA ops dispatch for PCIe support Daniel Machon
2026-09-28 19:32 ` [PATCH net-next v9 09/15] net: lan966x: clear FDMA interrupt stickies after switch reset Daniel Machon
2026-09-28 19:32 ` Daniel Machon [this message]
2026-10-02  7:33   ` [PATCH net-next v9 10/15] net: lan966x: add shutdown callback to stop the FDMA on reboot netdev-bot+sashiko
2026-09-28 19:32 ` [PATCH net-next v9 11/15] net: lan966x: add PCIe FDMA support Daniel Machon
2026-10-02  7:33   ` netdev-bot+sashiko
2026-10-02  9:02     ` Daniel Machon
2026-10-02 14:14   ` Simon Horman
2026-09-28 19:33 ` [PATCH net-next v9 12/15] net: lan966x: add PCIe FDMA MTU change support Daniel Machon
2026-10-02  7:33   ` netdev-bot+sashiko
2026-10-02  9:08     ` Daniel Machon
2026-09-28 19:33 ` [PATCH net-next v9 13/15] net: lan966x: add PCIe FDMA XDP support Daniel Machon
2026-10-02  7:33   ` netdev-bot+sashiko
2026-10-02  9:11     ` Daniel Machon
2026-09-28 19:33 ` [PATCH net-next v9 14/15] misc: lan966x-pci: dts: extend cpu reg to cover PCIE DBI space Daniel Machon
2026-10-02  7:33   ` netdev-bot+sashiko
2026-09-28 19:33 ` [PATCH net-next v9 15/15] misc: lan966x-pci: dts: add fdma interrupt to overlay Daniel Machon
2026-10-02  7:33   ` netdev-bot+sashiko
2026-10-02  9:16     ` Daniel Machon
2026-10-02 20:20 ` [PATCH net-next v9 00/15] net: lan966x: add support for PCIe FDMA patchwork-bot+netdevbpf

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260928-lan966x-pci-fdma-v9-10-a17caf60f89a@microchip.com \
    --to=daniel.machon@microchip.com \
    --cc=UNGLinuxDriver@microchip.com \
    --cc=andrew+netdev@lunn.ch \
    --cc=arnd@arndb.de \
    --cc=ast@kernel.org \
    --cc=bpf@vger.kernel.org \
    --cc=daniel@iogearbox.net \
    --cc=davem@davemloft.net \
    --cc=edumazet@google.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=hawk@kernel.org \
    --cc=herve.codina@bootlin.com \
    --cc=horatiu.vultur@microchip.com \
    --cc=horms@kernel.org \
    --cc=john.fastabend@gmail.com \
    --cc=kuba@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mohsin.bashr@gmail.com \
    --cc=netdev@vger.kernel.org \
    --cc=pabeni@redhat.com \
    --cc=richardcochran@gmail.com \
    --cc=sdf@fomichev.me \
    --cc=steen.hegelund@microchip.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox