Netdev List
 help / color / mirror / Atom feed
From: Joe Damato <joe@dama.to>
To: netdev@vger.kernel.org, Michael Chan <michael.chan@broadcom.com>,
	Pavan Chebbi <pavan.chebbi@broadcom.com>,
	Andrew Lunn <andrew+netdev@lunn.ch>,
	"David S. Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@kernel.org>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	Prashant Sreedharan <prashant@broadcom.com>
Cc: edumazet@google.com, horms@kernel.org,
	selvin.xavier@broadcom.com, kalesh-anakkur.purayil@broadcom.com,
	linux-kernel@vger.kernel.org, Joe Damato <joe@dama.to>
Subject: [PATCH net v6 4/5] bnxt_en: refuse to open a device with stopped DMA
Date: Fri, 20 Nov 2026 07:28:26 -0800	[thread overview]
Message-ID: <20261120152830.699712-5-joe@dama.to> (raw)
In-Reply-To: <20261120152830.699712-1-joe@dama.to>

Add BNXT_STATE_DMA_STOPPED and set it in bnxt_stop_dma() to signal that
the device had DMA disabled. When opening the device later, check this
bit and exit with an error. Also add the bit to BNXT_NO_FW_ACCESS() so
HWRM commands sent after DMA is stopped fail right away instead of
waiting for the timeout.

This is a very rare case, but when it happens the driver must be rebound
to make the device usable again.

Fixes: 74608fc98d28 ("bnxt_en: Ring free response from close path should use completion ring")
Signed-off-by: Joe Damato <joe@dama.to>
---
 drivers/net/ethernet/broadcom/bnxt/bnxt.c | 26 ++++++++++++++++++++---
 drivers/net/ethernet/broadcom/bnxt/bnxt.h |  2 ++
 2 files changed, 25 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/bnxt/bnxt.c b/drivers/net/ethernet/broadcom/bnxt/bnxt.c
index 600a8c866f3c..9daf053293a4 100644
--- a/drivers/net/ethernet/broadcom/bnxt/bnxt.c
+++ b/drivers/net/ethernet/broadcom/bnxt/bnxt.c
@@ -7847,9 +7847,20 @@ static void bnxt_stop_dma(struct bnxt *bp)
 
 	netdev_err(bp->dev,
 		   "Disabling DMA before releasing ring memory, the driver must be rebound to recover\n");
+	set_bit(BNXT_STATE_DMA_STOPPED, &bp->state);
 	pci_clear_master(bp->pdev);
 }
 
+static int bnxt_check_dma_stopped(struct bnxt *bp)
+{
+	if (!test_bit(BNXT_STATE_DMA_STOPPED, &bp->state))
+		return 0;
+
+	netdev_err(bp->dev,
+		   "DMA was disabled after the firmware failed to free rings, rebind the driver to recover\n");
+	return -ENODEV;
+}
+
 static int __bnxt_trim_rings(struct bnxt *bp, int *rx, int *tx, int max,
 			     bool shared);
 static int bnxt_trim_rings(struct bnxt *bp, int *rx, int *tx, int max,
@@ -13440,9 +13451,10 @@ static int __bnxt_open_nic(struct bnxt *bp, bool irq_re_init, bool link_re_init)
 
 int bnxt_open_nic(struct bnxt *bp, bool irq_re_init, bool link_re_init)
 {
-	int rc = 0;
+	int rc;
 
-	if (test_bit(BNXT_STATE_ABORT_ERR, &bp->state))
+	rc = bnxt_check_dma_stopped(bp);
+	if (!rc && test_bit(BNXT_STATE_ABORT_ERR, &bp->state))
 		rc = -EIO;
 	if (!rc)
 		rc = __bnxt_open_nic(bp, irq_re_init, link_re_init);
@@ -13459,7 +13471,11 @@ int bnxt_open_nic(struct bnxt *bp, bool irq_re_init, bool link_re_init)
  */
 int bnxt_half_open_nic(struct bnxt *bp)
 {
-	int rc = 0;
+	int rc;
+
+	rc = bnxt_check_dma_stopped(bp);
+	if (rc)
+		goto half_open_err;
 
 	if (test_bit(BNXT_STATE_ABORT_ERR, &bp->state)) {
 		netdev_err(bp->dev, "A previous firmware reset has not completed, aborting half open\n");
@@ -13519,6 +13535,10 @@ static int bnxt_open(struct net_device *dev)
 	struct bnxt *bp = netdev_priv(dev);
 	int rc;
 
+	rc = bnxt_check_dma_stopped(bp);
+	if (rc)
+		return rc;
+
 	if (test_bit(BNXT_STATE_ABORT_ERR, &bp->state)) {
 		rc = bnxt_reinit_after_abort(bp);
 		if (rc) {
diff --git a/drivers/net/ethernet/broadcom/bnxt/bnxt.h b/drivers/net/ethernet/broadcom/bnxt/bnxt.h
index 41d05efd6307..50c024dd3c6c 100644
--- a/drivers/net/ethernet/broadcom/bnxt/bnxt.h
+++ b/drivers/net/ethernet/broadcom/bnxt/bnxt.h
@@ -2474,9 +2474,11 @@ struct bnxt {
 #define BNXT_STATE_FW_NON_FATAL_COND	13
 #define BNXT_STATE_FW_ACTIVATE_RESET	14
 #define BNXT_STATE_HALF_OPEN		15	/* For offline ethtool tests */
+#define BNXT_STATE_DMA_STOPPED		16
 
 #define BNXT_NO_FW_ACCESS(bp)					\
 	(test_bit(BNXT_STATE_FW_FATAL_COND, &(bp)->state) ||	\
+	 test_bit(BNXT_STATE_DMA_STOPPED, &(bp)->state) ||	\
 	 pci_channel_offline((bp)->pdev))
 
 	struct bnxt_irq	*irq_tbl;
-- 
2.53.1-Meta


  parent reply	other threads:[~2026-11-20 15:28 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-11-20 15:28 [PATCH net v6 0/5] bnxt_en: Make RING FREE more robust Joe Damato
2026-11-20 15:28 ` [PATCH net v6 1/5] bnxt_en: return the RING_FREE status to callers Joe Damato
2026-11-20 15:28 ` [PATCH net v6 2/5] bnxt_en: check HWRM response if completion never arrives Joe Damato
2026-11-20 15:28 ` [PATCH net v6 3/5] bnxt_en: stop DMA before releasing rings the firmware did not free Joe Damato
2026-11-20 15:28 ` Joe Damato [this message]
2026-11-20 15:28 ` [PATCH net v6 5/5] bnxt_en: stop the ULP around the reset task Joe Damato

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20261120152830.699712-5-joe@dama.to \
    --to=joe@dama.to \
    --cc=andrew+netdev@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=edumazet@google.com \
    --cc=edumazet@kernel.org \
    --cc=horms@kernel.org \
    --cc=kalesh-anakkur.purayil@broadcom.com \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=michael.chan@broadcom.com \
    --cc=netdev@vger.kernel.org \
    --cc=pabeni@redhat.com \
    --cc=pavan.chebbi@broadcom.com \
    --cc=prashant@broadcom.com \
    --cc=selvin.xavier@broadcom.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox