From mboxrd@z Thu Jan 1 00:00:00 1970 From: Murali Karicheri Subject: Re: [net-next PATCH v2 03/10] net: netcp: ethss: make call to gbe_sgmii_config() conditional Date: Thu, 29 Mar 2018 12:27:40 -0400 Message-ID: <24d6d476-1c04-c9be-e32f-4d024be649f2@ti.com> References: <1522168309-12338-1-git-send-email-m-karicheri2@ti.com> <1522168309-12338-4-git-send-email-m-karicheri2@ti.com> <20180327171817.GO5862@lunn.ch> Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Cc: mark.rutland@arm.com, devicetree@vger.kernel.org, malat@debian.org, netdev@vger.kernel.org, linux-kernel@vger.kernel.org, w-kwok2@ti.com, robh+dt@kernel.org, ssantosh@kernel.org, davem@davemloft.net, linux-arm-kernel@lists.infradead.org To: Andrew Lunn Return-path: In-Reply-To: <20180327171817.GO5862@lunn.ch> Content-Language: en-US List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Sender: "linux-arm-kernel" Errors-To: linux-arm-kernel-bounces+linux-arm-kernel=m.gmane.org@lists.infradead.org List-Id: netdev.vger.kernel.org On 03/27/2018 01:18 PM, Andrew Lunn wrote: > On Tue, Mar 27, 2018 at 12:31:42PM -0400, Murali Karicheri wrote: >> As a preparatory patch to add support for 2u cpsw hardware found on >> K2G SoC, make call to gbe_sgmii_config() conditional. This is required >> since 2u uses RGMII interface instead of SGMII and to allow for driver >> re-use. >> >> Signed-off-by: Murali Karicheri >> --- >> drivers/net/ethernet/ti/netcp_ethss.c | 7 +++++-- >> 1 file changed, 5 insertions(+), 2 deletions(-) >> >> diff --git a/drivers/net/ethernet/ti/netcp_ethss.c b/drivers/net/ethernet/ti/netcp_ethss.c >> index 56dbc0b..1dea891 100644 >> --- a/drivers/net/ethernet/ti/netcp_ethss.c >> +++ b/drivers/net/ethernet/ti/netcp_ethss.c >> @@ -2271,7 +2271,8 @@ static int gbe_slave_open(struct gbe_intf *gbe_intf) >> >> void (*hndlr)(struct net_device *) = gbe_adjust_link; >> >> - gbe_sgmii_config(priv, slave); >> + if ((priv->ss_version == GBE_SS_VERSION_14) || IS_SS_ID_NU(priv)) >> + gbe_sgmii_config(priv, slave); > > Or maybe: > > if (slave->phy_node == PHY_INTERFACE_MODE_SGMII) > gbe_sgmii_config(priv, slave); > > Andrew > Actually, on specific cpsw hardware, driver supports specific interface. Driver also uses link-interface DT property to configure this and link-interface can be without phy as well. So essentially the above code looks good IMO. I need to change this as if (IS_SS_ID_VER_14(priv) || IS_SS_ID_NU(priv)) gbe_sgmii_config(priv, slave); Based on the link-interface, driver selects the phy mode and pass it to of_phy_connect(). I will update the above in v3. -- Murali Karicheri Linux Kernel, Keystone