From: Antonio Almeida <vexwek@gmail.com>
To: Jarek Poplawski <jarkao2@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>,
Stephen Hemminger <shemminger@vyatta.com>,
netdev@vger.kernel.org, davem@davemloft.net, devik@cdi.cz,
Eric Dumazet <dada1@cosmosbay.com>,
Vladimir Ivashchenko <hazard@francoudi.com>
Subject: Re: [PATCH iproute2] Re: HTB accuracy for high speed
Date: Thu, 4 Jun 2009 14:50:06 +0100 [thread overview]
Message-ID: <298f5c050906040650y31de6fdcv865e775d52bc977c@mail.gmail.com> (raw)
In-Reply-To: <20090603095412.GC5644@ff.dom.local>
On Wed, Jun 3, 2009 at 10:54 AM, Jarek Poplawski wrote:
> Antonio, could you give this patch a try (with all the previous) and
> repeat those HFSC tests you did before (plus maybe a few tries with
> lower rates)?
For me, HTB values are just perfect! I would say that they're better
than HFSC, since sent rate stays below the configured ceil (but that's
for me)
After applying the patch you sent (to sch_hfsc.c) I got these values for HFSC:
configuration analyser RX error (%)
10000000 10062688 0,63
20000000 20096961 0,48
30000000 30135028 0,45
40000000 40186190 0,47
50000000 50294890 0,59
60000000 60294553 0,49
70000000 70284220 0,41
80000000 80414272 0,52
90000000 90354675 0,39
100000000 100453024 0,45
200000000 200962041 0,48
250000000 251467886 0,59
300000000 301422613 0,47
400000000 402123479 0,53
500000000 502356820 0,47
550000000 552988253 0,54
600000000 602956905 0,49
700000000 703405632 0,49
750000000 753949085 0,53
800000000 804315169 0,54
900000000 904584208 0,51
As usually, generating 970Mbit/s of tcp traffic of 800 bytes packets.
Here's the setup picture:
# tc -s -d class ls dev eth1
class hfsc 1: root
Sent 253924 bytes 319 pkt (dropped 0, overlimits 0 requeues 0)
rate 0bit 0pps backlog 0b 0p requeues 0
period 0 level 4
class hfsc 1:1 parent 1: sc m1 0bit d 0us m2 1000Mbit ul m1 0bit d 0us
m2 1000Mbit
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
rate 0bit 0pps backlog 0b 0p requeues 0
period 2 work 299437688 bytes level 3
class hfsc 1:10 parent 1:2 sc m1 0bit d 0us m2 1000Mbit ul m1 0bit d
0us m2 1000Mbit
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
rate 0bit 0pps backlog 0b 0p requeues 0
period 2 work 299437688 bytes level 1
class hfsc 1:2 parent 1:1 sc m1 0bit d 0us m2 1000Mbit ul m1 0bit d
0us m2 1000Mbit
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
rate 0bit 0pps backlog 0b 0p requeues 0
period 2 work 299437688 bytes level 2
class hfsc 1:108 parent 1:10 sc m1 0bit d 50.0ms m2 500000Kbit ul m1
0bit d 0us m2 500000Kbit
Sent 300178764 bytes 377109 pkt (dropped 349464, overlimits 0 requeues 0)
rate 0bit 0pps backlog 0b 931p requeues 0
period 2 work 299437688 bytes rtwork 299437688 bytes level 0
If you'd like any other values just ask. I'll be away till the fourteenth.
Thanks a lot! Good job!
Antonio Almeida
next prev parent reply other threads:[~2009-06-04 13:50 UTC|newest]
Thread overview: 104+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <298f5c050905150745p13dc226eia1ff50ffa8c4b300@mail.gmail.com>
2009-05-15 14:49 ` HTB accuracy for high speed Antonio Almeida
2009-05-15 18:12 ` Stephen Hemminger
2009-05-18 10:01 ` Antonio Almeida
2009-05-18 10:45 ` Jarek Poplawski
2009-05-18 12:27 ` Antonio Almeida
2009-05-18 12:32 ` Jarek Poplawski
2009-05-18 16:13 ` Stephen Hemminger
2009-05-18 18:03 ` Antonio Almeida
2009-05-18 22:02 ` Stephen Hemminger
2009-05-19 11:48 ` Antonio Almeida
2009-05-19 13:08 ` Antonio Almeida
2009-05-16 8:31 ` Jarek Poplawski
2009-05-18 10:39 ` Antonio Almeida
2009-05-18 11:14 ` Jarek Poplawski
2009-05-18 12:05 ` Antonio Almeida
2009-05-16 14:14 ` Jarek Poplawski
2009-05-18 14:36 ` Antonio Almeida
2009-05-18 23:14 ` Vladimir Ivashchenko
2009-05-18 23:27 ` Vladimir Ivashchenko
2009-05-19 11:03 ` Jarek Poplawski
2009-05-19 14:04 ` Vladimir Ivashchenko
2009-05-19 20:10 ` Jarek Poplawski
2009-05-20 22:07 ` Vladimir Ivashchenko
2009-05-20 22:46 ` Eric Dumazet
2009-05-21 7:20 ` Jarek Poplawski
2009-05-21 7:44 ` Vladimir Ivashchenko
2009-05-21 8:28 ` Jarek Poplawski
2009-05-21 9:07 ` Eric Dumazet
2009-05-21 9:22 ` Jarek Poplawski
2009-05-23 10:37 ` HTB accuracy for high speed (and bonding) Vladimir Ivashchenko
2009-05-23 14:34 ` Jarek Poplawski
2009-05-23 15:06 ` Vladimir Ivashchenko
2009-05-23 15:35 ` Jarek Poplawski
2009-05-23 15:53 ` Vladimir Ivashchenko
2009-05-23 16:02 ` Jarek Poplawski
2009-05-18 16:40 ` HTB accuracy for high speed Eric Dumazet
2009-05-18 17:23 ` Jarek Poplawski
2009-05-18 21:52 ` David Miller
2009-05-18 23:59 ` [PATCH] pkt_sched: gen_estimator: use 64 bits intermediate counters for bps Eric Dumazet
2009-05-19 2:27 ` David Miller
2009-05-19 7:02 ` Jarek Poplawski
2009-05-19 7:31 ` Eric Dumazet
2009-05-19 7:42 ` Jarek Poplawski
2009-05-19 7:57 ` Jarek Poplawski
2009-05-19 18:03 ` Eric Dumazet
2009-05-19 19:09 ` [PATCH] pkt_sched: gen_estimator: Fix signed integers right-shifts Jarek Poplawski
2009-05-26 5:47 ` David Miller
2009-05-19 8:18 ` [PATCH] pkt_sched: gen_estimator: use 64 bits intermediate counters for bps David Miller
2009-05-17 20:15 ` HTB accuracy for high speed Jarek Poplawski
2009-05-18 6:56 ` [PATCH iproute2] " Jarek Poplawski
2009-05-18 16:54 ` Antonio Almeida
2009-05-18 17:16 ` Antonio Almeida
2009-05-21 8:51 ` Jarek Poplawski
2009-05-22 17:42 ` Antonio Almeida
2009-05-23 7:32 ` Jarek Poplawski
2009-05-28 18:13 ` Antonio Almeida
2009-05-28 21:12 ` Jarek Poplawski
2009-05-29 17:02 ` Antonio Almeida
2009-05-29 17:28 ` Stephen Hemminger
2009-05-29 19:58 ` Jarek Poplawski
2009-05-29 19:46 ` Jarek Poplawski
2009-05-29 20:49 ` Stephen Hemminger
2009-05-29 20:59 ` Jarek Poplawski
2009-05-30 20:07 ` Jarek Poplawski
2009-06-02 10:12 ` Antonio Almeida
2009-06-02 11:45 ` Antonio Almeida
2009-06-02 12:36 ` Jarek Poplawski
2009-06-02 12:45 ` Patrick McHardy
2009-06-02 13:08 ` Jarek Poplawski
2009-06-02 13:20 ` Patrick McHardy
2009-06-02 21:37 ` Jarek Poplawski
2009-06-02 21:50 ` Jarek Poplawski
2009-06-03 7:06 ` Patrick McHardy
2009-06-03 7:40 ` Jarek Poplawski
2009-06-03 7:53 ` Patrick McHardy
2009-06-03 8:01 ` Jarek Poplawski
2009-06-03 8:29 ` Patrick McHardy
2009-06-03 8:45 ` Jarek Poplawski
2009-06-03 9:54 ` Jarek Poplawski
2009-06-03 10:01 ` Patrick McHardy
2009-06-03 10:05 ` Patrick McHardy
2009-06-03 10:06 ` Patrick McHardy
2009-06-03 10:27 ` Jarek Poplawski
2009-06-04 13:50 ` Antonio Almeida [this message]
[not found] ` <20090604193013.GA2755@ami.dom.local>
[not found] ` <4A282216.20203@trash.net>
[not found] ` <20090604194203.GB2755@ami.dom.local>
2009-06-09 5:25 ` Badalian Vyacheslav
2009-06-09 5:49 ` Jarek Poplawski
2009-06-04 4:53 ` David Miller
2009-06-04 7:50 ` Jarek Poplawski
2009-05-18 17:53 ` Jarek Poplawski
2009-05-18 18:23 ` Antonio Almeida
2009-05-18 18:32 ` Jarek Poplawski
2009-05-18 18:56 ` Antonio Almeida
2009-05-18 19:05 ` Jarek Poplawski
2009-05-19 10:55 ` Antonio Almeida
2009-05-19 11:04 ` Denys Fedoryschenko
2009-05-19 11:18 ` Jarek Poplawski
2009-05-19 11:21 ` Denys Fedoryschenko
2009-05-19 11:28 ` Jarek Poplawski
2009-05-19 14:31 ` Antonio Almeida
2009-05-19 11:09 ` Jarek Poplawski
2009-05-19 13:18 ` Jesper Dangaard Brouer
2009-05-19 19:35 ` Jarek Poplawski
2009-05-18 7:01 ` [PATCH iproute2 v2] " Jarek Poplawski
2009-05-17 20:29 ` Vladimir Ivashchenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=298f5c050906040650y31de6fdcv865e775d52bc977c@mail.gmail.com \
--to=vexwek@gmail.com \
--cc=dada1@cosmosbay.com \
--cc=davem@davemloft.net \
--cc=devik@cdi.cz \
--cc=hazard@francoudi.com \
--cc=jarkao2@gmail.com \
--cc=kaber@trash.net \
--cc=netdev@vger.kernel.org \
--cc=shemminger@vyatta.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).