* Re: Strange network timeouts w/ 2.6.30.5
[not found] <1359163732.51250769223038.JavaMail.root@mail.holmansrus.com>
@ 2009-08-20 11:54 ` Walt Holman
2009-08-20 13:45 ` Krzysztof Halasa
0 siblings, 1 reply; 14+ messages in thread
From: Walt Holman @ 2009-08-20 11:54 UTC (permalink / raw)
To: Krzysztof Halasa; +Cc: David Miller, linux-kernel, netdev
[-- Attachment #1: Type: text/plain, Size: 2084 bytes --]
----- "Krzysztof Halasa" <khc@pm.waw.pl> wrote:
> > Since patching to 2.6.30.5 I'm experiencing periodic timeouts on my
> > e100 which is used as my WAN interface on a server/router box.
> Nothing
> > is reported in any logs and eventually the traffic resumes. It
> seems
> > to happen at fairly regular intervals, although I've not timed
> them.
> > The timeouts last for approx. 60-120 seconds and then traffic
> resumes
> > normally with no hint of what happened.
>
> x86-64, intel P965...
>
> Can you provide "dmesg" output, please?
>
> I wonder what additional side effect did the patch cause. Streaming
> allocs on such x86 should already be coherent, no?
>
> Perhaps you have more than 2 GB RAM (or so) and swiotlb has to
> provide
> buffering? I think of something like:
>
> - the driver does "sync for CPU" and examines status
> - the descriptor is tested to be still empty
> - meanwhile e100 chip changes the status in the descriptor
> - the driver does "sync for device" (it's what the patch added)
> - at this point swiotlb doesn't know the descriptor is clean and
> writes
> it out, thus dropping the change done by the e100 chip.
>
> Does the above seem plausible? I admit I'm not swiotlb expert, it's
> a pure guess that it simply and blindly moves data in and out.
>
> If that's the case, I don't really know how could it work without the
> patch in question. Perhaps the timings were just right?
>
> What can we do with it? Rewriting to use consistent allocs, of
> course.
> Temporarily adding #ifdef CONFIG_ARM around the
> pci_dma_sync_single_for_device()? Not sure if other archs were
> affected.
>
> The root problem is that the driver shouldn't use streaming
> allocations
> for its descriptors (they are written from both sides
> simultaneously).
> Only skb->data can be streaming.
> --
> Krzysztof Halasa
Hi Krzystof,
dmesg is attached. This box does have >2GB Ram (6GB total). The dmesg will show e100 init'd 3 times since the first is the stock modprobe, 2nd was forced with use_io and the 3rd modprobe was after reverting the patch.
-Walt
[-- Attachment #2: dmesg.txt --]
[-- Type: text/plain, Size: 60717 bytes --]
[ 0.000000] Linux version 2.6.30-patched-r5 (root@waltsputer) (gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #1 SMP PREEMPT Wed Aug 19 17:51:30 CDT 2009
[ 0.000000] Command line: root=/dev/mapper/vg0-root ro resume=/dev/vg0/swap splash vga=791 elevator=deadline
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 0000000000098000 (usable)
[ 0.000000] BIOS-e820: 0000000000098000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e3000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000cffb0000 (usable)
[ 0.000000] BIOS-e820: 00000000cffb0000 - 00000000cffbe000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000cffbe000 - 00000000cfff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000cfff0000 - 00000000d0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 00000001b0000000 (usable)
[ 0.000000] DMI present.
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0x1b0000 max_arch_pfn = 0x100000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-DFFFF write-protect
[ 0.000000] E0000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 1B0000000 mask FF0000000 uncachable
[ 0.000000] 1 base 1C0000000 mask FC0000000 uncachable
[ 0.000000] 2 base 000000000 mask E00000000 write-back
[ 0.000000] 3 base 0D0000000 mask FF0000000 uncachable
[ 0.000000] 4 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 00000000d0000000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0xcffb0 max_arch_pfn = 0x100000000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000cffb0000
[ 0.000000] 0000000000 - 00cfe00000 page 2M
[ 0.000000] 00cfe00000 - 00cffb0000 page 4k
[ 0.000000] kernel direct mapping tables up to cffb0000 @ 10000-16000
[ 0.000000] init_memory_mapping: 0000000100000000-00000001b0000000
[ 0.000000] 0100000000 - 01b0000000 page 2M
[ 0.000000] kernel direct mapping tables up to 1b0000000 @ 14000-1c000
[ 0.000000] RAMDISK: 37a3a000 - 37fef4b7
[ 0.000000] ACPI: RSDP 00000000000f93a0 00014 (v00 ACPIAM)
[ 0.000000] ACPI: RSDT 00000000cffb0000 00038 (v01 M S I OEMRSDT 12000701 MSFT 00000097)
[ 0.000000] ACPI: FACP 00000000cffb0200 00084 (v02 M S I OEMFACP 12000701 MSFT 00000097)
[ 0.000000] ACPI: DSDT 00000000cffb0440 052CE (v01 0AAAA 0AAAA000 00000000 INTL 20051117)
[ 0.000000] ACPI: FACS 00000000cffbe000 00040
[ 0.000000] ACPI: APIC 00000000cffb0390 0006C (v01 M S I OEMAPIC 12000701 MSFT 00000097)
[ 0.000000] ACPI: MCFG 00000000cffb0400 0003C (v01 M S I OEMMCFG 12000701 MSFT 00000097)
[ 0.000000] ACPI: OEMB 00000000cffbe040 00061 (v01 M S I AMI_OEM 12000701 MSFT 00000097)
[ 0.000000] ACPI: SSDT 00000000cffbe9d0 00A7C (v01 DpgPmm CpuPm 00000012 INTL 20051117)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] (8 early reservations) ==> bootmem [0000000000 - 01b0000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0000200000 - 0000730ca8] TEXT DATA BSS ==> [0000200000 - 0000730ca8]
[ 0.000000] #3 [0037a3a000 - 0037fef4b7] RAMDISK ==> [0037a3a000 - 0037fef4b7]
[ 0.000000] #4 [0000098000 - 0000100000] BIOS reserved ==> [0000098000 - 0000100000]
[ 0.000000] #5 [0000731000 - 0000731133] BRK ==> [0000731000 - 0000731133]
[ 0.000000] #6 [0000010000 - 0000014000] PGTABLE ==> [0000010000 - 0000014000]
[ 0.000000] #7 [0000014000 - 0000017000] PGTABLE ==> [0000014000 - 0000017000]
[ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780
[ 0.000000] [ffffe20000000000-ffffe20005ffffff] PMD -> [ffff880028200000-ffff88002e1fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x001b0000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x00000098
[ 0.000000] 0: 0x00000100 -> 0x000cffb0
[ 0.000000] 0: 0x00100000 -> 0x001b0000
[ 0.000000] On node 0 totalpages: 1572664
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1442 pages reserved
[ 0.000000] DMA zone: 2478 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 833512 pages, LIFO batch:31
[ 0.000000] Normal zone: 9856 pages used for memmap
[ 0.000000] Normal zone: 711040 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 0000000000098000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e3000
[ 0.000000] PM: Registered nosave memory: 00000000000e3000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000cffb0000 - 00000000cffbe000
[ 0.000000] PM: Registered nosave memory: 00000000cffbe000 - 00000000cfff0000
[ 0.000000] PM: Registered nosave memory: 00000000cfff0000 - 00000000d0000000
[ 0.000000] PM: Registered nosave memory: 00000000d0000000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffb00000
[ 0.000000] PM: Registered nosave memory: 00000000ffb00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at d4000000 (gap: d0000000:2ee00000)
[ 0.000000] NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 25 pages at ffff880028034000, static data 70176 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1547030
[ 0.000000] Kernel command line: root=/dev/mapper/vg0-root ro resume=/dev/vg0/swap splash vga=791 elevator=deadline
[ 0.000000] Initializing CPU#0
[ 0.000000] NR_IRQS:384
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2400.190 MHz processor.
[ 0.000999] Console: colour dummy device 80x25
[ 0.000999] console [tty0] enabled
[ 0.000999] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.000999] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000999] Checking aperture...
[ 0.000999] No AGP bridge found
[ 0.000999] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.000999] Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
[ 0.000999] software IO TLB at phys 0x20000000 - 0x24000000
[ 0.000999] Memory: 6101284k/7077888k available (3010k kernel code, 787232k absent, 188416k reserved, 1325k data, 384k init)
[ 0.000999] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.001009] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.38 BogoMIPS (lpj=2400190)
[ 0.001041] Security Framework initialized
[ 0.001049] SELinux: Disabled at boot.
[ 0.001059] Mount-cache hash table entries: 256
[ 0.001198] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.001204] CPU: L2 cache: 4096K
[ 0.001210] CPU: Physical Processor ID: 0
[ 0.001214] CPU: Processor Core ID: 0
[ 0.001224] CPU0: Thermal monitoring enabled (TM2)
[ 0.001230] using mwait in idle threads.
[ 0.001251] ACPI: Core revision 20090320
[ 0.008759] Setting APIC routing to flat
[ 0.008998] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.019119] CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
[ 0.019996] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.000999] Initializing CPU#1
[ 0.000999] Calibrating delay using timer specific routine.. 4798.99 BogoMIPS (lpj=2399499)
[ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.000999] CPU: L2 cache: 4096K
[ 0.000999] CPU: Physical Processor ID: 0
[ 0.000999] CPU: Processor Core ID: 1
[ 0.000999] CPU1: Thermal monitoring enabled (TM2)
[ 0.000999] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.091152] CPU1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
[ 0.091206] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.092012] Brought up 2 CPUs
[ 0.092018] Total of 2 processors activated (9599.37 BogoMIPS).
[ 0.092085] net_namespace: 1712 bytes
[ 0.092085] NET: Registered protocol family 16
[ 0.092085] ACPI: bus type pci registered
[ 0.092993] dca service started, version 1.8
[ 0.093020] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.093027] PCI: Not using MMCONFIG.
[ 0.093031] PCI: Using configuration type 1 for base access
[ 0.095028] bio: create slab <bio-0> at 0
[ 0.096550] ACPI: EC: Look up EC in DSDT
[ 0.105318] ACPI: Interpreter enabled
[ 0.105325] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.105351] ACPI: Using IOAPIC for interrupt routing
[ 0.105406] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.108911] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[ 0.118543] PCI: Using MMCONFIG at e0000000 - efffffff
[ 0.128037] ACPI Warning (tbutils-0246): Incorrect checksum in table [OEMB] - 3D, should be 34 [20090320]
[ 0.128162] ACPI: No dock devices found.
[ 0.128370] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.128400] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.128400] pci 0000:00:01.0: PME# disabled
[ 0.128400] pci 0000:00:1a.0: reg 20 io port: [0xac00-0xac1f]
[ 0.128400] pci 0000:00:1a.1: reg 20 io port: [0xa880-0xa89f]
[ 0.128400] pci 0000:00:1a.7: reg 10 32bit mmio: [0xfbfffc00-0xfbffffff]
[ 0.128400] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.128400] pci 0000:00:1a.7: PME# disabled
[ 0.128400] pci 0000:00:1b.0: reg 10 64bit mmio: [0xfbff8000-0xfbffbfff]
[ 0.128400] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.128400] pci 0000:00:1b.0: PME# disabled
[ 0.128400] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.128400] pci 0000:00:1c.0: PME# disabled
[ 0.129027] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.129034] pci 0000:00:1c.4: PME# disabled
[ 0.129087] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.129094] pci 0000:00:1c.5: PME# disabled
[ 0.129135] pci 0000:00:1d.0: reg 20 io port: [0xa800-0xa81f]
[ 0.129178] pci 0000:00:1d.1: reg 20 io port: [0xa480-0xa49f]
[ 0.129220] pci 0000:00:1d.2: reg 20 io port: [0xa400-0xa41f]
[ 0.129268] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfbfff800-0xfbfffbff]
[ 0.129312] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.129319] pci 0000:00:1d.7: PME# disabled
[ 0.129426] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[ 0.129436] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[ 0.129443] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff)
[ 0.129501] pci 0000:00:1f.2: reg 10 io port: [0xa080-0xa087]
[ 0.129507] pci 0000:00:1f.2: reg 14 io port: [0xa000-0xa003]
[ 0.129512] pci 0000:00:1f.2: reg 18 io port: [0x9c00-0x9c07]
[ 0.129517] pci 0000:00:1f.2: reg 1c io port: [0x9880-0x9883]
[ 0.129522] pci 0000:00:1f.2: reg 20 io port: [0x9800-0x981f]
[ 0.129527] pci 0000:00:1f.2: reg 24 32bit mmio: [0xfbfff000-0xfbfff7ff]
[ 0.129551] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.129557] pci 0000:00:1f.2: PME# disabled
[ 0.129581] pci 0000:00:1f.3: reg 10 32bit mmio: [0xfbffec00-0xfbffecff]
[ 0.129596] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
[ 0.129637] pci 0000:01:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
[ 0.129644] pci 0000:01:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
[ 0.129652] pci 0000:01:00.0: reg 1c 64bit mmio: [0xfc000000-0xfcffffff]
[ 0.129657] pci 0000:01:00.0: reg 24 io port: [0xbc00-0xbc7f]
[ 0.129661] pci 0000:01:00.0: reg 30 32bit mmio: [0xfe8e0000-0xfe8fffff]
[ 0.129712] pci 0000:00:01.0: bridge io port: [0xb000-0xbfff]
[ 0.129715] pci 0000:00:01.0: bridge 32bit mmio: [0xfc000000-0xfe8fffff]
[ 0.129719] pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.129842] pci 0000:03:00.0: reg 24 32bit mmio: [0xfe9fe000-0xfe9fffff]
[ 0.129851] pci 0000:03:00.0: reg 30 32bit mmio: [0xfe9e0000-0xfe9effff]
[ 0.129880] pci 0000:03:00.0: PME# supported from D3hot
[ 0.129889] pci 0000:03:00.0: PME# disabled
[ 0.129940] pci 0000:03:00.1: reg 10 io port: [0xcc00-0xcc07]
[ 0.129949] pci 0000:03:00.1: reg 14 io port: [0xc880-0xc883]
[ 0.129957] pci 0000:03:00.1: reg 18 io port: [0xc800-0xc807]
[ 0.129965] pci 0000:03:00.1: reg 1c io port: [0xc480-0xc483]
[ 0.129974] pci 0000:03:00.1: reg 20 io port: [0xc400-0xc40f]
[ 0.130064] pci 0000:00:1c.4: bridge io port: [0xc000-0xcfff]
[ 0.130067] pci 0000:00:1c.4: bridge 32bit mmio: [0xfe900000-0xfe9fffff]
[ 0.130125] pci 0000:04:00.0: reg 10 io port: [0xd800-0xd8ff]
[ 0.130145] pci 0000:04:00.0: reg 18 64bit mmio: [0xfeaff000-0xfeafffff]
[ 0.130166] pci 0000:04:00.0: reg 30 32bit mmio: [0xfeac0000-0xfeadffff]
[ 0.130209] pci 0000:04:00.0: supports D1 D2
[ 0.130211] pci 0000:04:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.130220] pci 0000:04:00.0: PME# disabled
[ 0.130266] pci 0000:00:1c.5: bridge io port: [0xd000-0xdfff]
[ 0.130270] pci 0000:00:1c.5: bridge 32bit mmio: [0xfea00000-0xfeafffff]
[ 0.130303] pci 0000:05:00.0: reg 10 32bit mmio: [0xfebff000-0xfebfffff]
[ 0.130309] pci 0000:05:00.0: reg 14 io port: [0xec00-0xec3f]
[ 0.130315] pci 0000:05:00.0: reg 18 32bit mmio: [0xfebc0000-0xfebdffff]
[ 0.130333] pci 0000:05:00.0: reg 30 32bit mmio: [0xfebe0000-0xfebeffff]
[ 0.130350] pci 0000:05:00.0: supports D1 D2
[ 0.130352] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.130359] pci 0000:05:00.0: PME# disabled
[ 0.130397] pci 0000:05:04.0: reg 10 32bit mmio: [0xfebfe800-0xfebfefff]
[ 0.130403] pci 0000:05:04.0: reg 14 io port: [0xe880-0xe8ff]
[ 0.130442] pci 0000:05:04.0: supports D2
[ 0.130444] pci 0000:05:04.0: PME# supported from D2 D3hot D3cold
[ 0.130451] pci 0000:05:04.0: PME# disabled
[ 0.130493] pci 0000:00:1e.0: transparent bridge
[ 0.130500] pci 0000:00:1e.0: bridge io port: [0xe000-0xefff]
[ 0.130503] pci 0000:00:1e.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
[ 0.130524] pci_bus 0000:00: on NUMA node 0
[ 0.130529] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.130668] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.130773] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.130834] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[ 0.130892] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[ 0.145066] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.145189] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.145312] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 *14 15)
[ 0.145433] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.145553] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.145673] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[ 0.145793] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.146068] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[ 0.146126] SCSI subsystem initialized
[ 0.146126] libata version 3.00 loaded.
[ 0.146126] usbcore: registered new interface driver usbfs
[ 0.146126] usbcore: registered new interface driver hub
[ 0.146126] usbcore: registered new device driver usb
[ 0.146126] PCI: Using ACPI for IRQ routing
[ 0.155043] pnp: PnP ACPI init
[ 0.155058] ACPI: bus type pnp registered
[ 0.159165] pnp: PnP ACPI: found 17 devices
[ 0.159171] ACPI: ACPI bus type pnp unregistered
[ 0.159182] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
[ 0.159193] system 00:0a: ioport range 0xa10-0xaef has been reserved
[ 0.159199] system 00:0a: ioport range 0xae0-0xaef has been reserved
[ 0.159208] system 00:0b: ioport range 0x4d0-0x4d1 has been reserved
[ 0.159214] system 00:0b: ioport range 0x800-0x87f has been reserved
[ 0.159221] system 00:0b: ioport range 0x480-0x4bf has been reserved
[ 0.159227] system 00:0b: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.159234] system 00:0b: iomem range 0xfed20000-0xfed8ffff has been reserved
[ 0.159243] system 00:0d: iomem range 0xffc00000-0xffefffff has been reserved
[ 0.159252] system 00:0e: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.159260] system 00:0e: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.159269] system 00:0f: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.159278] system 00:10: iomem range 0x0-0x9ffff could not be reserved
[ 0.159284] system 00:10: iomem range 0xc0000-0xcffff has been reserved
[ 0.159290] system 00:10: iomem range 0xe0000-0xfffff could not be reserved
[ 0.159297] system 00:10: iomem range 0x100000-0xcfffffff could not be reserved
[ 0.164187] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.164194] pci 0000:00:01.0: IO window: 0xb000-0xbfff
[ 0.164201] pci 0000:00:01.0: MEM window: 0xfc000000-0xfe8fffff
[ 0.164207] pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
[ 0.164217] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.164223] pci 0000:00:1c.0: IO window: disabled
[ 0.164230] pci 0000:00:1c.0: MEM window: disabled
[ 0.164236] pci 0000:00:1c.0: PREFETCH window: disabled
[ 0.164245] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03
[ 0.164251] pci 0000:00:1c.4: IO window: 0xc000-0xcfff
[ 0.164259] pci 0000:00:1c.4: MEM window: 0xfe900000-0xfe9fffff
[ 0.164266] pci 0000:00:1c.4: PREFETCH window: disabled
[ 0.164274] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:04
[ 0.164280] pci 0000:00:1c.5: IO window: 0xd000-0xdfff
[ 0.164288] pci 0000:00:1c.5: MEM window: 0xfea00000-0xfeafffff
[ 0.164295] pci 0000:00:1c.5: PREFETCH window: disabled
[ 0.164304] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
[ 0.164310] pci 0000:00:1e.0: IO window: 0xe000-0xefff
[ 0.164318] pci 0000:00:1e.0: MEM window: 0xfeb00000-0xfebfffff
[ 0.164325] pci 0000:00:1e.0: PREFETCH window: 0x000000f0000000-0x000000f00fffff
[ 0.164342] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.164349] pci 0000:00:01.0: setting latency timer to 64
[ 0.164356] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.164363] pci 0000:00:1c.0: setting latency timer to 64
[ 0.164369] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.164376] pci 0000:00:1c.4: setting latency timer to 64
[ 0.164382] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.164389] pci 0000:00:1c.5: setting latency timer to 64
[ 0.164394] pci 0000:00:1e.0: setting latency timer to 64
[ 0.164398] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.164400] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.164402] pci_bus 0000:01: resource 0 io: [0xb000-0xbfff]
[ 0.164404] pci_bus 0000:01: resource 1 mem: [0xfc000000-0xfe8fffff]
[ 0.164406] pci_bus 0000:01: resource 2 pref mem [0xd0000000-0xdfffffff]
[ 0.164409] pci_bus 0000:03: resource 0 io: [0xc000-0xcfff]
[ 0.164411] pci_bus 0000:03: resource 1 mem: [0xfe900000-0xfe9fffff]
[ 0.164413] pci_bus 0000:04: resource 0 io: [0xd000-0xdfff]
[ 0.164415] pci_bus 0000:04: resource 1 mem: [0xfea00000-0xfeafffff]
[ 0.164417] pci_bus 0000:05: resource 0 io: [0xe000-0xefff]
[ 0.164419] pci_bus 0000:05: resource 1 mem: [0xfeb00000-0xfebfffff]
[ 0.164421] pci_bus 0000:05: resource 2 pref mem [0xf0000000-0xf00fffff]
[ 0.164423] pci_bus 0000:05: resource 3 io: [0x00-0xffff]
[ 0.164425] pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.164438] NET: Registered protocol family 2
[ 0.175320] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.176457] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.178204] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.178762] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.178769] TCP reno registered
[ 0.181438] NET: Registered protocol family 1
[ 0.181507] Trying to unpack rootfs image as initramfs...
[ 0.323858] Freeing initrd memory: 5845k freed
[ 0.327609] Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 0.327820] audit: initializing netlink socket (disabled)
[ 0.327837] type=2000 audit(1250706533.327:1): initialized
[ 0.330179] VFS: Disk quotas dquot_6.5.2
[ 0.330232] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.330845] msgmni has been set to 11929
[ 0.330986] alg: No test for stdrng (krng)
[ 0.330996] io scheduler noop registered
[ 0.331003] io scheduler anticipatory registered
[ 0.331008] io scheduler deadline registered (default)
[ 0.331020] io scheduler cfq registered
[ 0.331145] pci 0000:01:00.0: Boot video device
[ 0.331161] pci 0000:05:00.0: Firmware left e100 interrupts enabled; disabling
[ 0.331297] pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
[ 0.331308] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 0.331440] pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X
[ 0.331451] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 0.331610] pcieport-driver 0000:00:1c.4: irq 26 for MSI/MSI-X
[ 0.331621] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[ 0.331783] pcieport-driver 0000:00:1c.5: irq 27 for MSI/MSI-X
[ 0.331794] pcieport-driver 0000:00:1c.5: setting latency timer to 64
[ 0.332185] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc20010100000, using 3072k, total 262144k
[ 0.332194] vesafb: mode is 1024x768x16, linelength=2048, pages=1
[ 0.332200] vesafb: scrolling: redraw
[ 0.332205] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 0.344339] Console: switching to colour frame buffer device 128x48
[ 0.355413] fb0: VESA VGA frame buffer device
[ 0.355636] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.355807] ACPI: Power Button [PWRF]
[ 0.355980] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.356171] ACPI: Power Button [PWRB]
[ 0.356751] ACPI: SSDT 00000000cffbe0b0 00277 (v01 DpgPmm P001Ist 00000011 INTL 20051117)
[ 0.357236] processor ACPI_CPU:00: registered as cooling_device0
[ 0.357773] ACPI: SSDT 00000000cffbe540 00277 (v01 DpgPmm P002Ist 00000012 INTL 20051117)
[ 0.358242] processor ACPI_CPU:01: registered as cooling_device1
[ 0.386443] Non-volatile memory driver v1.3
[ 0.386638] Linux agpgart interface v0.103
[ 0.386823] Floppy drive(s): fd0 is 1.44M
[ 0.401137] FDC 0 is a post-1991 82077
[ 0.403337] brd: module loaded
[ 0.404014] loop: module loaded
[ 0.404170] Driver 'sd' needs updating - please use bus_type methods
[ 0.404356] ahci 0000:00:1f.2: version 3.0
[ 0.404370] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.404572] ahci 0000:00:1f.2: irq 28 for MSI/MSI-X
[ 0.404614] ahci: SSS flag set, parallel bus scan disabled
[ 0.407056] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl RAID mode
[ 0.409668] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems
[ 0.412392] ahci 0000:00:1f.2: setting latency timer to 64
[ 0.417770] scsi0 : ahci
[ 0.420629] scsi1 : ahci
[ 0.423454] scsi2 : ahci
[ 0.426301] scsi3 : ahci
[ 0.429142] scsi4 : ahci
[ 0.431992] scsi5 : ahci
[ 0.434936] ata1: SATA max UDMA/133 abar m2048@0xfbfff000 port 0xfbfff100 irq 28
[ 0.437952] ata2: SATA max UDMA/133 abar m2048@0xfbfff000 port 0xfbfff180 irq 28
[ 0.440976] ata3: SATA max UDMA/133 abar m2048@0xfbfff000 port 0xfbfff200 irq 28
[ 0.444013] ata4: SATA max UDMA/133 abar m2048@0xfbfff000 port 0xfbfff280 irq 28
[ 0.447062] ata5: SATA max UDMA/133 abar m2048@0xfbfff000 port 0xfbfff300 irq 28
[ 0.450124] ata6: SATA max UDMA/133 abar m2048@0xfbfff000 port 0xfbfff380 irq 28
[ 0.453221] ahci 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.456436] ahci 0000:03:00.0: JMB361 has only one port, port_map 0x3 -> 0x1
[ 0.470776] ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x1 impl SATA mode
[ 0.474236] ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part
[ 0.477746] ahci 0000:03:00.0: setting latency timer to 64
[ 0.477851] scsi6 : ahci
[ 0.481451] scsi7 : ahci
[ 0.485072] ata7: SATA max UDMA/133 abar m8192@0xfe9fe000 port 0xfe9fe100 irq 16
[ 0.488833] ata8: DUMMY
[ 0.492673] pata_jmicron 0000:03:00.1: enabling device (0000 -> 0001)
[ 0.496640] pata_jmicron 0000:03:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.500622] pata_jmicron 0000:03:00.1: setting latency timer to 64
[ 0.500678] scsi8 : pata_jmicron
[ 0.504633] scsi9 : pata_jmicron
[ 0.508441] ata9: PATA max UDMA/100 cmd 0xcc00 ctl 0xc880 bmdma 0xc400 irq 17
[ 0.512257] ata10: PATA max UDMA/100 cmd 0xc800 ctl 0xc480 bmdma 0xc408 irq 17
[ 0.516226] usbmon: debugfs is not available
[ 0.519912] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.523647] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.527356] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 0.527359] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 0.530996] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 0.538457] ehci_hcd 0000:00:1a.7: debug port 1
[ 0.541950] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 0.541961] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfbfffc00
[ 0.554855] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 0.558411] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.561997] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.565629] usb usb1: Product: EHCI Host Controller
[ 0.569276] usb usb1: Manufacturer: Linux 2.6.30-patched-r5 ehci_hcd
[ 0.572945] usb usb1: SerialNumber: 0000:00:1a.7
[ 0.576635] usb usb1: configuration #1 chosen from 1 choice
[ 0.580269] hub 1-0:1.0: USB hub found
[ 0.583778] hub 1-0:1.0: 4 ports detected
[ 0.587391] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.590886] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.590888] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.594437] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 0.601979] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.605636] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.605647] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfbfff800
[ 0.618957] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.622780] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.626570] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.630446] usb usb2: Product: EHCI Host Controller
[ 0.634368] usb usb2: Manufacturer: Linux 2.6.30-patched-r5 ehci_hcd
[ 0.638406] usb usb2: SerialNumber: 0000:00:1d.7
[ 0.642539] usb usb2: configuration #1 chosen from 1 choice
[ 0.646738] hub 2-0:1.0: USB hub found
[ 0.650818] hub 2-0:1.0: 6 ports detected
[ 0.655016] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.659162] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.663271] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 0.663274] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 0.667340] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 0.671519] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ac00
[ 0.675632] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.679747] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.683850] usb usb3: Product: UHCI Host Controller
[ 0.687932] usb usb3: Manufacturer: Linux 2.6.30-patched-r5 uhci_hcd
[ 0.692019] usb usb3: SerialNumber: 0000:00:1a.0
[ 0.696204] usb usb3: configuration #1 chosen from 1 choice
[ 0.700349] hub 3-0:1.0: USB hub found
[ 0.704385] hub 3-0:1.0: 2 ports detected
[ 0.708483] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.712508] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 0.712511] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 0.716488] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 0.720509] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880
[ 0.724500] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.728519] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.732578] usb usb4: Product: UHCI Host Controller
[ 0.736643] usb usb4: Manufacturer: Linux 2.6.30-patched-r5 uhci_hcd
[ 0.740710] usb usb4: SerialNumber: 0000:00:1a.1
[ 0.744798] usb usb4: configuration #1 chosen from 1 choice
[ 0.748847] hub 4-0:1.0: USB hub found
[ 0.752815] hub 4-0:1.0: 2 ports detected
[ 0.756878] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.760910] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.760913] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.764926] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 0.769016] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a800
[ 0.773048] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.777116] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.781196] usb usb5: Product: UHCI Host Controller
[ 0.785243] usb usb5: Manufacturer: Linux 2.6.30-patched-r5 uhci_hcd
[ 0.789364] usb usb5: SerialNumber: 0000:00:1d.0
[ 0.793539] usb usb5: configuration #1 chosen from 1 choice
[ 0.797670] hub 5-0:1.0: USB hub found
[ 0.801726] hub 5-0:1.0: 2 ports detected
[ 0.805858] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.809940] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.809943] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.814003] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 0.818112] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a480
[ 0.822187] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.826343] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.830484] usb usb6: Product: UHCI Host Controller
[ 0.834574] usb usb6: Manufacturer: Linux 2.6.30-patched-r5 uhci_hcd
[ 0.838706] usb usb6: SerialNumber: 0000:00:1d.1
[ 0.842861] usb usb6: configuration #1 chosen from 1 choice
[ 0.847007] hub 6-0:1.0: USB hub found
[ 0.851041] hub 6-0:1.0: 2 ports detected
[ 0.855171] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.859229] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.859232] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.863272] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 0.867332] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a400
[ 0.871376] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.875446] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.879575] usb usb7: Product: UHCI Host Controller
[ 0.883649] usb usb7: Manufacturer: Linux 2.6.30-patched-r5 uhci_hcd
[ 0.887770] usb usb7: SerialNumber: 0000:00:1d.2
[ 0.891913] usb usb7: configuration #1 chosen from 1 choice
[ 0.896049] hub 7-0:1.0: USB hub found
[ 0.900075] hub 7-0:1.0: 2 ports detected
[ 0.904285] usbcore: registered new interface driver libusual
[ 0.908366] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 0.914503] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.918576] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.922711] mice: PS/2 mouse device common for all mice
[ 0.926965] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 0.931177] rtc_cmos 00:03: RTC can wake from S4
[ 0.935325] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.939456] rtc0: alarms up to one month, y3k, 114 bytes nvram
[ 0.943610] md: linear personality registered for level -1
[ 0.947745] md: raid0 personality registered for level 0
[ 0.951841] md: raid1 personality registered for level 1
[ 0.955862] md: multipath personality registered for level -4
[ 0.959897] cpuidle: using governor ladder
[ 0.963871] cpuidle: using governor menu
[ 0.968383] usbcore: registered new interface driver hiddev
[ 0.972366] usbcore: registered new interface driver usbhid
[ 0.976248] usbhid: v2.6:USB HID core driver
[ 0.980232] TCP bic registered
[ 0.984054] TCP cubic registered
[ 0.987855] TCP westwood registered
[ 0.991605] TCP highspeed registered
[ 0.995314] TCP hybla registered
[ 0.998936] TCP htcp registered
[ 1.002506] TCP vegas registered
[ 1.006099] TCP veno registered
[ 1.009545] TCP scalable registered
[ 1.012952] TCP lp registered
[ 1.016790] TCP yeah registered
[ 1.020104] TCP illinois registered
[ 1.023438] NET: Registered protocol family 17
[ 1.024617] ata9.00: ATAPI: HL-DT-ST GCE-8527B, 1.04, max UDMA/33
[ 1.024651] ata9.01: ATAPI: TSSTcorpCD/DVDW SH-S182M, SB06, max UDMA/33
[ 1.033976] NET: Registered protocol family 15
[ 1.057894] ata9.00: configured for UDMA/33
[ 1.067893] ata9.01: configured for UDMA/33
[ 1.090351] Switched to high resolution mode on CPU 1
[ 1.091097] Switched to high resolution mode on CPU 0
[ 1.092055] ata7: SATA link down (SStatus 0 SControl 300)
[ 1.092098] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.092641] ata1.00: ATA-7: WDC WD2500KS-00MJB0, 02.01C03, max UDMA/133
[ 1.092644] ata1.00: 488397168 sectors, multi 16: LBA48
[ 1.093277] ata1.00: configured for UDMA/133
[ 1.110570] scsi 0:0:0:0: Direct-Access ATA WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5
[ 1.114714] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[ 1.118621] sd 0:0:0:0: [sda] Write Protect is off
[ 1.122398] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.122425] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.126401] sda: sda1 sda2
[ 1.147955] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.469012] usb 5-1: new low speed USB device using uhci_hcd and address 2
[ 1.638977] usb 5-1: New USB device found, idVendor=046d, idProduct=c312
[ 1.642910] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.646869] usb 5-1: Product: USB Multimedia Keyboard
[ 1.650779] usb 5-1: Manufacturer: BTC
[ 1.654709] usb 5-1: configuration #1 chosen from 1 choice
[ 1.676332] input: BTC USB Multimedia Keyboard as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/input/input3
[ 1.680667] generic-usb 0003:046D:C312.0001: input,hidraw0: USB HID v1.10 Keyboard [BTC USB Multimedia Keyboard] on usb-0000:00:1d.0-1/input0
[ 1.730083] input: BTC USB Multimedia Keyboard as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.1/input/input4
[ 1.735029] generic-usb 0003:046D:C312.0002: input,hiddev96,hidraw1: USB HID v1.10 Device [BTC USB Multimedia Keyboard] on usb-0000:00:1d.0-1/input1
[ 1.837016] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.842542] ata2.00: ATA-7: WDC WD2500KS-00MJB0, 02.01C03, max UDMA/133
[ 1.847626] ata2.00: 488397168 sectors, multi 16: LBA48
[ 1.853381] ata2.00: configured for UDMA/133
[ 1.880079] scsi 1:0:0:0: Direct-Access ATA WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5
[ 1.885628] sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[ 1.891057] sd 1:0:0:0: [sdb] Write Protect is off
[ 1.896471] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.896503] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.902211] sdb: sdb1 sdb2 < >
[ 1.938583] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 1.954042] usb 5-2: new low speed USB device using uhci_hcd and address 3
[ 2.117937] usb 5-2: New USB device found, idVendor=0764, idProduct=0501
[ 2.123823] usb 5-2: New USB device strings: Mfr=3, Product=1, SerialNumber=0
[ 2.129766] usb 5-2: Product: CP 1350C
[ 2.134998] usb 5-2: Manufacturer: CPS
[ 2.140192] usb 5-2: configuration #1 chosen from 1 choice
[ 2.303066] generic-usb 0003:0764:0501.0003: hiddev97,hidraw2: USB HID v1.10 Device [CPS CP 1350C] on usb-0000:00:1d.0-2/input0
[ 2.521011] usb 6-1: new low speed USB device using uhci_hcd and address 2
[ 2.602053] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.610142] ata3.00: ATA-8: WDC WD5000AAKS-22A7B0, 01.03B01, max UDMA/133
[ 2.616527] ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 2.624184] ata3.00: configured for UDMA/133
[ 2.641079] scsi 2:0:0:0: Direct-Access ATA WDC WD5000AAKS-2 01.0 PQ: 0 ANSI: 5
[ 2.647820] sd 2:0:0:0: [sdc] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[ 2.654327] sd 2:0:0:0: [sdc] Write Protect is off
[ 2.660711] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2.660743] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.667365] sdc: sdc1 sdc2
[ 2.688278] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 2.708030] usb 6-1: New USB device found, idVendor=046d, idProduct=c00c
[ 2.714495] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.720927] usb 6-1: Product: USB Mouse
[ 2.727287] usb 6-1: Manufacturer: Logitech
[ 2.733699] usb 6-1: configuration #1 chosen from 1 choice
[ 2.758341] input: Logitech USB Mouse as /devices/pci0000:00/0000:00:1d.1/usb6/6-1/6-1:1.0/input/input5
[ 2.765097] generic-usb 0003:046D:C00C.0004: input,hidraw3: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:1d.1-1/input0
[ 3.370015] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.377091] ata4.00: ATA-7: WDC WD2500KS-00MJB0, 02.01C03, max UDMA/133
[ 3.383517] ata4.00: 488397168 sectors, multi 16: LBA48
[ 3.390421] ata4.00: configured for UDMA/133
[ 3.417096] scsi 3:0:0:0: Direct-Access ATA WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5
[ 3.423381] sd 3:0:0:0: [sdd] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[ 3.429478] sd 3:0:0:0: [sdd] Write Protect is off
[ 3.435479] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 3.435517] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.441740] sdd: unknown partition table
[ 3.463357] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 4.162015] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.168883] ata5.00: ATA-8: WDC WD5000AAKS-00A7B0, 01.03B01, max UDMA/133
[ 4.174963] ata5.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 4.181959] ata5.00: configured for UDMA/133
[ 4.209073] scsi 4:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 01.0 PQ: 0 ANSI: 5
[ 4.215403] sd 4:0:0:0: [sde] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[ 4.221521] sd 4:0:0:0: [sde] Write Protect is off
[ 4.227559] sd 4:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 4.227584] sd 4:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.233837] sde: sde1 sde2
[ 4.246165] sd 4:0:0:0: [sde] Attached SCSI disk
[ 4.938014] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.944756] ata6.00: ATA-7: WDC WD2500KS-00MJB0, 02.01C03, max UDMA/133
[ 4.950880] ata6.00: 488397168 sectors, multi 16: LBA48
[ 4.957477] ata6.00: configured for UDMA/133
[ 4.985075] scsi 5:0:0:0: Direct-Access ATA WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5
[ 4.991370] sd 5:0:0:0: [sdf] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[ 4.997428] sd 5:0:0:0: [sdf] Write Protect is off
[ 5.003331] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 5.003356] sd 5:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.009477] sdf:<5>scsi 8:0:0:0: CD-ROM HL-DT-ST CD-RW GCE-8527B 1.04 PQ: 0 ANSI: 5
[ 5.015575] scsi 8:0:1:0: CD-ROM TSSTcorp CD/DVDW SH-S182M SB06 PQ: 0 ANSI: 5
[ 5.024442] sdf1 sdf2
[ 5.029907] sd 5:0:0:0: [sdf] Attached SCSI disk
[ 5.183707] rtc_cmos 00:03: setting system clock to 2009-08-19 18:28:59 UTC (1250706539)
[ 5.189798] Freeing unused kernel memory: 384k freed
[ 5.318498] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 5.328988] fuse init (API version 7.11)
[ 5.341688] xor: automatically using best checksumming function: generic_sse
[ 5.346127] generic_sse: 8392.000 MB/sec
[ 5.346129] xor: using function: generic_sse (8392.000 MB/sec)
[ 5.346454] async_tx: api initialized (async)
[ 5.364133] raid6: int64x1 1800 MB/s
[ 5.381142] raid6: int64x2 2714 MB/s
[ 5.398149] raid6: int64x4 2078 MB/s
[ 5.415145] raid6: int64x8 1847 MB/s
[ 5.432140] raid6: sse2x1 4210 MB/s
[ 5.449142] raid6: sse2x2 4476 MB/s
[ 5.466130] raid6: sse2x4 7144 MB/s
[ 5.466132] raid6: using algorithm sse2x4 (7144 MB/s)
[ 5.467793] md: raid6 personality registered for level 6
[ 5.467795] md: raid5 personality registered for level 5
[ 5.467797] md: raid4 personality registered for level 4
[ 5.472406] md: raid10 personality registered for level 10
[ 5.615588] Driver 'sr' needs updating - please use bus_type methods
[ 5.622646] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 5.622667] r8169 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 5.622688] r8169 0000:04:00.0: setting latency timer to 64
[ 5.622841] r8169 0000:04:00.0: irq 29 for MSI/MSI-X
[ 5.622952] eth0: RTL8168b/8111b at 0xffffc200100d4000, 00:16:17:d3:d0:e7, XID 38000000 IRQ 29
[ 5.623060] sr0: scsi3-mmc drive: 40x/52x writer cd/rw xa/form2 cdda tray
[ 5.623063] Uniform CD-ROM driver Revision: 3.20
[ 5.623139] sr 8:0:0:0: Attached scsi CD-ROM sr0
[ 5.625511] sr1: scsi3-mmc drive: 62x/62x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.625565] sr 8:0:1:0: Attached scsi CD-ROM sr1
[ 5.627819] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.627853] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 5.627888] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 5.627922] sd 3:0:0:0: Attached scsi generic sg3 type 0
[ 5.627957] sd 4:0:0:0: Attached scsi generic sg4 type 0
[ 5.628005] sd 5:0:0:0: Attached scsi generic sg5 type 0
[ 5.628039] sr 8:0:0:0: Attached scsi generic sg6 type 5
[ 5.628071] sr 8:0:1:0: Attached scsi generic sg7 type 5
[ 5.658545] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 5.658548] e100: Copyright(c) 1999-2006 Intel Corporation
[ 5.658577] e100 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 5.701394] e100 0000:05:00.0: PME# disabled
[ 5.701480] e100: eth1: e100_probe: addr 0xfebff000, irq 16, MAC addr 00:02:b3:8d:48:07
[ 5.701509] ohci1394 0000:05:04.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 5.755203] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[febfe800-febfefff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 5.849984] md: bind<sdc1>
[ 5.877118] md: bind<sdc2>
[ 5.902731] md: bind<sde1>
[ 5.904573] raid1: raid set md2 active with 2 out of 2 mirrors
[ 5.909643] md: bind<sdf1>
[ 5.911421] md: bind<sdf2>
[ 5.932572] md: bind<sde2>
[ 5.933917] md3: setting max_sectors to 128, segment boundary to 32767
[ 5.933921] raid0: looking at sde2
[ 5.933923] raid0: comparing sde2(976350208)<6> with sde2(976350208)
[ 5.933926] raid0: END
[ 5.933927] raid0: ==> UNIQUE
[ 5.933928] raid0: 1 zones
[ 5.933930] raid0: looking at sdc2
[ 5.933932] raid0: comparing sdc2(976350208)<6> with sde2(976350208)
[ 5.933935] raid0: EQUAL
[ 5.933936] raid0: FINAL 1 zones
[ 5.933938] raid0: done.
[ 5.933940] raid0 : md_size is 1952700416 sectors.
[ 5.933942] raid0 : conf->spacing is 1952700416 sectors.
[ 5.933944] raid0 : nb_zone is 1.
[ 5.933945] raid0 : Allocating 8 bytes for hash.
[ 5.958943] md: bind<sda2>
[ 5.959117] md: bind<sda1>
[ 5.979243] md1: setting max_sectors to 128, segment boundary to 32767
[ 5.979247] raid0: looking at sda2
[ 5.979249] raid0: comparing sda2(487990272)<6> with sda2(487990272)
[ 5.979252] raid0: END
[ 5.979253] raid0: ==> UNIQUE
[ 5.979255] raid0: 1 zones
[ 5.979256] raid0: looking at sdf2
[ 5.979258] raid0: comparing sdf2(487990272)<6> with sda2(487990272)
[ 5.979260] raid0: EQUAL
[ 5.979262] raid0: FINAL 1 zones
[ 5.979264] raid0: done.
[ 5.979266] raid0 : md_size is 975980544 sectors.
[ 5.979269] raid0 : conf->spacing is 975980544 sectors.
[ 5.979270] raid0 : nb_zone is 1.
[ 5.979272] raid0 : Allocating 8 bytes for hash.
[ 5.980408] raid1: raid set md0 active with 2 out of 2 mirrors
[ 6.030719] md2: unknown partition table
[ 6.037804] md1: unknown partition table
[ 6.041751] md0: unknown partition table
[ 6.068642] md3: unknown partition table
[ 7.018162] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc00010457f8]
[ 7.061663] PM: Starting manual resume from disk
[ 7.064424] EXT4-fs: barriers enabled
[ 7.074626] kjournald2 starting: pid 3223, dev dm-5:8, commit interval 5 seconds
[ 7.074639] EXT4-fs: delayed allocation enabled
[ 7.074642] EXT4-fs: file extents enabled
[ 7.074788] EXT4-fs: mballoc enabled
[ 7.074802] EXT4-fs: mounted filesystem dm-5 with ordered data mode
[ 8.394730] udev: starting version 141
[ 8.607493] nvidia: module license 'NVIDIA' taints kernel.
[ 8.607498] Disabling lock debugging due to kernel taint
[ 8.634600] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 8.634725] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 8.640466] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 8.994059] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 8.994684] HDA Intel 0000:00:1b.0: irq 30 for MSI/MSI-X
[ 8.994715] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 9.057771] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[ 9.057942] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6
[ 9.083984] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 9.083995] nvidia 0000:01:00.0: setting latency timer to 64
[ 9.084354] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 185.18.31 Tue Jul 28 17:52:27 PDT 2009
[ 10.440559] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 10.486046] f71882fg: Found f71882fg chip at 0xa10, revision 32
[ 10.486316] f71882fg f71882fg.2576: Fan: 1 is in duty-cycle mode
[ 10.486320] f71882fg f71882fg.2576: Fan: 2 is in duty-cycle mode
[ 10.486323] f71882fg f71882fg.2576: Fan: 3 is in duty-cycle mode
[ 10.486326] f71882fg f71882fg.2576: Fan: 4 is in duty-cycle mode
[ 10.500843] netconsole: local port 6665
[ 10.500848] netconsole: local IP 192.168.0.1
[ 10.500850] netconsole: interface eth0
[ 10.500852] netconsole: remote port 514
[ 10.500855] netconsole: remote IP 192.168.0.221
[ 10.500857] netconsole: remote ethernet address 00:0d:88:64:b8:d3
[ 10.500861] netconsole: device eth0 not up yet, forcing it
[ 10.501083] r8169: eth0: link up
[ 10.501089] r8169: eth0: link up
[ 10.502309] netconsole: carrier detect appears untrustworthy, waiting 4 seconds
[ 10.704236] e100: eth1 NIC Link is Up 100 Mbps Full Duplex
[ 14.506026] console [netcon0] enabled
[ 14.512246] netconsole: network logging started
[ 14.770052] Adding 3145720k swap on /dev/mapper/vg0-swap. Priority:-1 extents:1 across:3145720k
[ 15.387243] EXT4 FS on dm-5, internal journal on dm-5:8
[ 16.527199] EXT4-fs: barriers enabled
[ 16.536649] kjournald2 starting: pid 5389, dev dm-3:8, commit interval 5 seconds
[ 16.536844] EXT4 FS on dm-3, internal journal on dm-3:8
[ 16.536847] EXT4-fs: delayed allocation enabled
[ 16.536850] EXT4-fs: file extents enabled
[ 16.537244] EXT4-fs: mballoc enabled
[ 16.537260] EXT4-fs: mounted filesystem dm-3 with ordered data mode
[ 16.554360] EXT4-fs: barriers enabled
[ 16.564822] kjournald2 starting: pid 5390, dev dm-0:8, commit interval 5 seconds
[ 16.565007] EXT4 FS on dm-0, internal journal on dm-0:8
[ 16.565010] EXT4-fs: delayed allocation enabled
[ 16.565012] EXT4-fs: file extents enabled
[ 16.567658] EXT4-fs: mballoc enabled
[ 16.567673] EXT4-fs: mounted filesystem dm-0 with ordered data mode
[ 16.578518] EXT4-fs: barriers enabled
[ 16.584093] kjournald2 starting: pid 5391, dev dm-2:8, commit interval 5 seconds
[ 16.584296] EXT4 FS on dm-2, internal journal on dm-2:8
[ 16.584298] EXT4-fs: delayed allocation enabled
[ 16.584300] EXT4-fs: file extents enabled
[ 16.584451] EXT4-fs: mballoc enabled
[ 16.584464] EXT4-fs: mounted filesystem dm-2 with ordered data mode
[ 16.588407] EXT4-fs: barriers enabled
[ 16.591760] kjournald2 starting: pid 5392, dev dm-4:8, commit interval 5 seconds
[ 16.591961] EXT4 FS on dm-4, internal journal on dm-4:8
[ 16.591964] EXT4-fs: delayed allocation enabled
[ 16.591966] EXT4-fs: file extents enabled
[ 16.592052] EXT4-fs: mballoc enabled
[ 16.592065] EXT4-fs: mounted filesystem dm-4 with ordered data mode
[ 16.593618] EXT4-fs: barriers enabled
[ 16.598778] kjournald2 starting: pid 5393, dev dm-7:8, commit interval 5 seconds
[ 16.598976] EXT4 FS on dm-7, internal journal on dm-7:8
[ 16.598979] EXT4-fs: delayed allocation enabled
[ 16.598981] EXT4-fs: file extents enabled
[ 16.599676] EXT4-fs: mballoc enabled
[ 16.599689] EXT4-fs: mounted filesystem dm-7 with ordered data mode
[ 16.613323] kjournald starting. Commit interval 5 seconds
[ 16.662738] EXT3 FS on md2, internal journal
[ 16.662744] EXT3-fs: mounted filesystem with writeback data mode.
[ 17.511110] EXT4-fs: barriers enabled
[ 17.521147] kjournald2 starting: pid 5410, dev dm-10:8, commit interval 5 seconds
[ 17.521332] EXT4 FS on dm-10, internal journal on dm-10:8
[ 17.521335] EXT4-fs: delayed allocation enabled
[ 17.521337] EXT4-fs: file extents enabled
[ 17.522890] EXT4-fs: mballoc enabled
[ 17.522906] EXT4-fs: mounted filesystem dm-10 with ordered data mode
[ 22.347094] Bridge firewalling registered
[ 22.349970] device eth0 entered promiscuous mode
[ 22.352962] br0: port 1(eth0) entering learning state
[ 23.425669] NET: Registered protocol family 10
[ 23.425825] lo: Disabled Privacy Extensions
[ 33.572072] RPC: Registered udp transport module.
[ 33.572074] RPC: Registered tcp transport module.
[ 33.627093] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 33.671003] eth0: no IPv6 routers present
[ 34.065013] br0: no IPv6 routers present
[ 34.343028] eth1: no IPv6 routers present
[ 37.352007] br0: port 1(eth0) entering forwarding state
[ 40.624730] kjournald starting. Commit interval 5 seconds
[ 40.624744] EXT3 FS on loop0, internal journal
[ 40.624748] EXT3-fs: mounted filesystem with writeback data mode.
[ 41.152968] svc: failed to register lockdv1 RPC service (errno 97).
[ 43.016748] Bluetooth: Core ver 2.15
[ 43.018111] NET: Registered protocol family 31
[ 43.018114] Bluetooth: HCI device and connection manager initialized
[ 43.018117] Bluetooth: HCI socket layer initialized
[ 43.030150] Bluetooth: L2CAP ver 2.13
[ 43.030152] Bluetooth: L2CAP socket layer initialized
[ 43.036233] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 43.036236] Bluetooth: BNEP filters: protocol multicast
[ 43.053474] Bluetooth: SCO (Voice Link) ver 0.6
[ 43.053477] Bluetooth: SCO socket layer initialized
[ 43.355260] warning: `dhcpd3' uses 32-bit capabilities (legacy support in use)
[ 46.031969] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 46.032981] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 46.032984] nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
[ 46.032987] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 46.171814] Netfilter messages via NETLINK v0.30.
[ 46.175122] ctnetlink v0.93: registering with nfnetlink.
[ 46.274012] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 46.314164] Ebtables v2.0 registered
[ 46.745444] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.756588] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.757862] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.759230] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.760447] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.761479] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.762675] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.763710] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.764928] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.765989] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.788666] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.790720] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.792690] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.794183] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.797501] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 46.808203] physdev match: using --physdev-out in the OUTPUT, FORWARD and POSTROUTING chains for non-bridged traffic is not supported anymore.
[ 51.466763] tun: Universal TUN/TAP device driver, 1.6
[ 51.466771] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 51.554970] device tap0 entered promiscuous mode
[ 51.562932] br0: port 2(tap0) entering learning state
[ 61.943007] tap0: no IPv6 routers present
[ 66.562008] br0: port 2(tap0) entering forwarding state
[ 188.037005] tap1: no IPv6 routers present
[ 604.446194] br0: port 2(tap0) entering disabled state
[ 604.464975] br0: port 2(tap0) entering disabled state
[ 608.171021] br0: port 1(eth0) entering disabled state
[ 608.220021] device eth0 left promiscuous mode
[ 608.220027] br0: port 1(eth0) entering disabled state
[ 608.254047] e100 0000:05:00.0: PCI INT A disabled
[ 610.262158] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 610.262163] e100: Copyright(c) 1999-2006 Intel Corporation
[ 610.262203] e100 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 610.262212] e100: 0000:05:00.0: e100_probe: using i/o access mode
[ 610.292593] e100 0000:05:00.0: PME# disabled
[ 610.292928] e100: eth1: e100_probe: addr 0xec00, irq 16, MAC addr 00:02:b3:8d:48:07
[ 610.391181] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 612.701223] e100: eth1 NIC Link is Up 100 Mbps Full Duplex
[ 612.702538] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 623.121006] eth1: no IPv6 routers present
[ 653.265277] device eth0 entered promiscuous mode
[ 653.289450] r8169: eth0: link up
[ 653.291979] br0: port 1(eth0) entering learning state
[ 663.718008] eth0: no IPv6 routers present
[ 663.878004] br0: no IPv6 routers present
[ 668.291009] br0: port 1(eth0) entering forwarding state
[ 1328.222191] br0: port 1(eth0) entering disabled state
[ 1328.253472] device eth0 left promiscuous mode
[ 1328.253479] br0: port 1(eth0) entering disabled state
[ 1336.066201] e100 0000:05:00.0: PCI INT A disabled
[ 1339.306300] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 1339.306305] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1339.306345] e100 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1339.337539] e100 0000:05:00.0: PME# disabled
[ 1339.337699] e100: eth1: e100_probe: addr 0xfebff000, irq 16, MAC addr 00:02:b3:8d:48:07
[ 1339.395030] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 1341.704232] e100: eth1 NIC Link is Up 100 Mbps Full Duplex
[ 1341.705560] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 1348.231171] device eth0 entered promiscuous mode
[ 1348.233317] r8169: eth0: link up
[ 1348.237116] br0: port 1(eth0) entering learning state
[ 1358.297129] br0: no IPv6 routers present
[ 1359.157130] eth0: no IPv6 routers present
[ 1363.237131] br0: port 1(eth0) entering forwarding state
[ 1384.161011] br0: port 1(eth0) entering disabled state
[ 1384.194844] device eth0 left promiscuous mode
[ 1384.194850] br0: port 1(eth0) entering disabled state
[ 1384.325211] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 1384.371575] device eth0 entered promiscuous mode
[ 1384.373224] r8169: eth0: link up
[ 1384.377223] br0: port 1(eth0) entering learning state
[ 1395.181005] br0: no IPv6 routers present
[ 1395.239005] eth0: no IPv6 routers present
[ 1395.613990] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 1397.704232] e100: eth1 NIC Link is Up 100 Mbps Full Duplex
[ 1397.705557] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 1399.377010] br0: port 1(eth0) entering forwarding state
[ 1407.797005] eth1: no IPv6 routers present
[ 1443.531430] device tap1 entered promiscuous mode
[ 1443.536931] br0: port 2(tap1) entering learning state
[ 1448.309009] tap0: no IPv6 routers present
[ 1453.974007] tap1: no IPv6 routers present
[ 1458.536072] br0: port 2(tap1) entering forwarding state
[43624.334005] tap0: no IPv6 routers present
^ permalink raw reply [flat|nested] 14+ messages in thread