* RTL8139
@ 2003-12-15 17:33 Leo Cambilargiu
2003-12-15 19:23 ` RTL8139 Rask Ingemann Lambertsen
2003-12-15 19:51 ` RTL8139 Jeff Garzik
0 siblings, 2 replies; 4+ messages in thread
From: Leo Cambilargiu @ 2003-12-15 17:33 UTC (permalink / raw)
To: netdev
Hello readers:
I purchased a couple of encore ENL832-tx NIC's that Linux doesn't recognize.
they are based on RTL8139C (06117S1)
The module 8139too (2.4.23) doesn't load. It behaves as though no
recognized hardware exists.
Any comments?
Leo
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: RTL8139
2003-12-15 17:33 RTL8139 Leo Cambilargiu
@ 2003-12-15 19:23 ` Rask Ingemann Lambertsen
2003-12-15 19:51 ` RTL8139 Jeff Garzik
1 sibling, 0 replies; 4+ messages in thread
From: Rask Ingemann Lambertsen @ 2003-12-15 19:23 UTC (permalink / raw)
To: Leo Cambilargiu; +Cc: netdev
On Mon, Dec 15, 2003 at 03:33:57PM -0200, Leo Cambilargiu wrote:
> The module 8139too (2.4.23) doesn't load. It behaves as though no
> recognized hardware exists.
Normally the module will load fine even with no supported hardware. At least
PCI drivers tend to work that way.
> Any comments?
Show us the errors you get when you try to load the module. In case the
module does load fine but doesn't recognise your board, send us the output
of "lspci -vvv" (as root).
--
Regards,
Rask Ingemann Lambertsen
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: RTL8139
2003-12-15 17:33 RTL8139 Leo Cambilargiu
2003-12-15 19:23 ` RTL8139 Rask Ingemann Lambertsen
@ 2003-12-15 19:51 ` Jeff Garzik
2003-12-17 12:23 ` RTL8139 Krishnakumar. R
1 sibling, 1 reply; 4+ messages in thread
From: Jeff Garzik @ 2003-12-15 19:51 UTC (permalink / raw)
To: Leo Cambilargiu; +Cc: netdev
Leo Cambilargiu wrote:
> Hello readers:
>
> I purchased a couple of encore ENL832-tx NIC's that Linux doesn't
> recognize.
>
> they are based on RTL8139C (06117S1)
>
> The module 8139too (2.4.23) doesn't load. It behaves as though no
> recognized hardware exists.
>
> Any comments?
Probably you need to add PCI ids to 8139too.c...
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: RTL8139
2003-12-15 19:51 ` RTL8139 Jeff Garzik
@ 2003-12-17 12:23 ` Krishnakumar. R
0 siblings, 0 replies; 4+ messages in thread
From: Krishnakumar. R @ 2003-12-17 12:23 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Leo Cambilargiu, netdev
Hi,
When i am trying to download the manual
of 8139C from realtek site, I am getting
8139C(L) manual. And as per that the
device id should be 8129 for 8139C(L).
So there is a possibility that if you
enable the CONFIG_8139TOO_8129 you might
get the card working.
Leo,
Have you enabled
"Support for older RTL-8129/8130 boards"
option in the make menuconfig(that will enable the
CONFIG_8139TOO_8129 )? If not then can you enable
it and try out ?
Regards,
KK.
On Tue, 2003-12-16 at 04:51, Jeff Garzik wrote:
> Leo Cambilargiu wrote:
> > Hello readers:
> >
> > I purchased a couple of encore ENL832-tx NIC's that Linux doesn't
> > recognize.
> >
> > they are based on RTL8139C (06117S1)
> >
> > The module 8139too (2.4.23) doesn't load. It behaves as though no
> > recognized hardware exists.
> >
> > Any comments?
>
>
> Probably you need to add PCI ids to 8139too.c...
>
>
>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2003-12-17 12:23 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-12-15 17:33 RTL8139 Leo Cambilargiu
2003-12-15 19:23 ` RTL8139 Rask Ingemann Lambertsen
2003-12-15 19:51 ` RTL8139 Jeff Garzik
2003-12-17 12:23 ` RTL8139 Krishnakumar. R
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).