From: Oleksandr Natalenko <oleksandr@natalenko.name>
To: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: kvalo@codeaurora.org, linux-wireless@vger.kernel.org,
nbd@nbd.name, hkallweit1@gmail.com, sgruszka@redhat.com,
lorenzo.bianconi@redhat.com, netdev@vger.kernel.org
Subject: Re: [PATCH v3 wireless-drivers 1/2] mt76: mt76x2e: disable pcie_aspm by default
Date: Sun, 27 Oct 2019 22:40:30 +0100 [thread overview]
Message-ID: <3e11e1da564178e43ab745c780094098@natalenko.name> (raw)
In-Reply-To: <cbd541284b80a966e2050ac809a495c55cfb591e.1572204430.git.lorenzo@kernel.org>
Hi.
On 27.10.2019 20:53, Lorenzo Bianconi wrote:
> On same device (e.g. U7612E-H1) PCIE_ASPM causes continuous mcu hangs
> and
> instability. Since mt76x2 series does not manage PCIE PS states, first
> we
> try to disable ASPM using pci_disable_link_state. If it fails, we will
> disable PCIE PS configuring PCI registers.
> This patch has been successfully tested on U7612E-H1 mini-pice card
>
> Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
For this revision, not yet ;) (see below).
> Signed-off-by: Felix Fietkau <nbd@nbd.name>
> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
> ---
> drivers/net/wireless/mediatek/mt76/Makefile | 2 +
> drivers/net/wireless/mediatek/mt76/mt76.h | 1 +
> .../net/wireless/mediatek/mt76/mt76x2/pci.c | 2 +
> drivers/net/wireless/mediatek/mt76/pci.c | 46 +++++++++++++++++++
> 4 files changed, 51 insertions(+)
> create mode 100644 drivers/net/wireless/mediatek/mt76/pci.c
>
> diff --git a/drivers/net/wireless/mediatek/mt76/Makefile
> b/drivers/net/wireless/mediatek/mt76/Makefile
> index 4d03596e891f..d7a1ddc9e407 100644
> --- a/drivers/net/wireless/mediatek/mt76/Makefile
> +++ b/drivers/net/wireless/mediatek/mt76/Makefile
> @@ -8,6 +8,8 @@ mt76-y := \
> mmio.o util.o trace.o dma.o mac80211.o debugfs.o eeprom.o \
> tx.o agg-rx.o mcu.o
>
> +mt76-$(CONFIG_PCI) += pci.o
> +
> mt76-usb-y := usb.o usb_trace.o
>
> CFLAGS_trace.o := -I$(src)
> diff --git a/drivers/net/wireless/mediatek/mt76/mt76.h
> b/drivers/net/wireless/mediatek/mt76/mt76.h
> index 570c159515a0..dc468ed9434a 100644
> --- a/drivers/net/wireless/mediatek/mt76/mt76.h
> +++ b/drivers/net/wireless/mediatek/mt76/mt76.h
> @@ -578,6 +578,7 @@ bool __mt76_poll_msec(struct mt76_dev *dev, u32
> offset, u32 mask, u32 val,
> #define mt76_poll_msec(dev, ...) __mt76_poll_msec(&((dev)->mt76),
> __VA_ARGS__)
>
> void mt76_mmio_init(struct mt76_dev *dev, void __iomem *regs);
> +void mt76_pci_disable_aspm(struct pci_dev *pdev);
>
> static inline u16 mt76_chip(struct mt76_dev *dev)
> {
> diff --git a/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> b/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> index 73c3104f8858..cf611d1b817c 100644
> --- a/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> +++ b/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> @@ -81,6 +81,8 @@ mt76pci_probe(struct pci_dev *pdev, const struct
> pci_device_id *id)
> /* RG_SSUSB_CDR_BR_PE1D = 0x3 */
> mt76_rmw_field(dev, 0x15c58, 0x3 << 6, 0x3);
>
> + mt76_pci_disable_aspm(pdev);
> +
> return 0;
>
> error:
> diff --git a/drivers/net/wireless/mediatek/mt76/pci.c
> b/drivers/net/wireless/mediatek/mt76/pci.c
> new file mode 100644
> index 000000000000..04c5a692bc85
> --- /dev/null
> +++ b/drivers/net/wireless/mediatek/mt76/pci.c
> @@ -0,0 +1,46 @@
> +// SPDX-License-Identifier: ISC
> +/*
> + * Copyright (C) 2019 Lorenzo Bianconi <lorenzo@kernel.org>
> + */
> +
> +#include <linux/pci.h>
FYI, I had to #include <linux/pci-aspm.h> on 5.3 kernel because this is
where pci_disable_link_state() is defined. It is not needed on 5.4+
since the declaration got moved to pci.h; this is just a note for those
who are going to test these changes on 5.3.
I'm still building the kernel, though. Will get back with the results
later.
> +
> +void mt76_pci_disable_aspm(struct pci_dev *pdev)
> +{
> + struct pci_dev *parent = pdev->bus->self;
> + u16 aspm_conf, parent_aspm_conf = 0;
> +
> + pcie_capability_read_word(pdev, PCI_EXP_LNKCTL, &aspm_conf);
> + aspm_conf &= PCI_EXP_LNKCTL_ASPMC;
> + if (parent) {
> + pcie_capability_read_word(parent, PCI_EXP_LNKCTL,
> + &parent_aspm_conf);
> + parent_aspm_conf &= PCI_EXP_LNKCTL_ASPMC;
> + }
> +
> + if (!aspm_conf && (!parent || !parent_aspm_conf)) {
> + /* aspm already disabled */
> + return;
> + }
> +
> + dev_info(&pdev->dev, "disabling ASPM %s %s\n",
> + (aspm_conf & PCI_EXP_LNKCTL_ASPM_L0S) ? "L0s" : "",
> + (aspm_conf & PCI_EXP_LNKCTL_ASPM_L1) ? "L1" : "");
> +
> + if (IS_ENABLED(CONFIG_PCIEASPM)) {
> + int err;
> +
> + err = pci_disable_link_state(pdev, aspm_conf);
> + if (!err)
> + return;
> + }
> +
> + /* both device and parent should have the same ASPM setting.
> + * disable ASPM in downstream component first and then upstream.
> + */
> + pcie_capability_clear_word(pdev, PCI_EXP_LNKCTL, aspm_conf);
> + if (parent)
> + pcie_capability_clear_word(parent, PCI_EXP_LNKCTL,
> + aspm_conf);
> +}
> +EXPORT_SYMBOL_GPL(mt76_pci_disable_aspm);
--
Oleksandr Natalenko (post-factum)
next prev parent reply other threads:[~2019-10-27 21:40 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-27 19:53 [PATCH v3 wireless-drivers 0/2] fix mt76x2e hangs on U7612E mini-pcie Lorenzo Bianconi
2019-10-27 19:53 ` [PATCH v3 wireless-drivers 1/2] mt76: mt76x2e: disable pcie_aspm by default Lorenzo Bianconi
2019-10-27 21:40 ` Oleksandr Natalenko [this message]
2019-10-30 15:00 ` Kalle Valo
2019-10-27 19:53 ` [PATCH v3 wireless-drivers 2/2] mt76: dma: fix buffer unmap with non-linear skbs Lorenzo Bianconi
2019-10-28 7:17 ` [PATCH v3 wireless-drivers 0/2] fix mt76x2e hangs on U7612E mini-pcie Oleksandr Natalenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3e11e1da564178e43ab745c780094098@natalenko.name \
--to=oleksandr@natalenko.name \
--cc=hkallweit1@gmail.com \
--cc=kvalo@codeaurora.org \
--cc=linux-wireless@vger.kernel.org \
--cc=lorenzo.bianconi@redhat.com \
--cc=lorenzo@kernel.org \
--cc=nbd@nbd.name \
--cc=netdev@vger.kernel.org \
--cc=sgruszka@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).