* Trivial IPv6-for-Fedora HOWTO
@ 2004-08-22 22:51 Jeff Garzik
2004-08-22 23:08 ` Paul Fraser
0 siblings, 1 reply; 4+ messages in thread
From: Jeff Garzik @ 2004-08-22 22:51 UTC (permalink / raw)
To: Netdev; +Cc: Linux Kernel, David Woodhouse
So, thanks to David Woodhouse for showing me how to do this. IPv6
appears to be very, very close to a Just Works(tm) state.
These instructions are for Fedora Core 2 users, and describe how to set
up IPv6 automatically tunnelling (6to4) on an IPv4 network. If you are
stuck on an IPv4-only network (like most of us), this enables
communication with IPv6 hosts quickly, easily, and transparently.
(this HOWTO is archived at http://yyz.us/ipv6-fc2-howto.html)
Simple setup:
1) Append to /etc/sysconfig/network
NETWORKING_IPV6=yes
IPV6_DEFAULTDEV=tun6to4
2) Append to /etc/sysconfig/ifcfg-eth0
IPV6INIT=yes
IPV6TO4INIT=yes
3) Reboot or restart your network interface.
That's it!
If you have an iptables ipv4 firewall, you'll want to
F1) allow ipv6 tunnelled packets to pass through to ip6tables, by
allowing protocol 41
iptables -A block -p 41 -j ACCEPT
("block" is a custom chain on my firewall)
F2) duplicate your ipv4 firewall rules for ipv6, using ip6tables. Some
things, like masquerade, are not applicable to ipv6.
If you have an ipv4 NATing firewall, which serves as a router for a
local network, you'll want to set up radvd and routing rules, so that
your hosts autoconfigure ipv6 automatically based on your router's
advertisements, and also so that your hosts truly speak native ipv6
without tunneling [the router does the tunnel wrap/unwrap].
R1.1) in /etc/radvd.conf, set "interface ethX" to reflect your router's
local LAN interface (eth1 on my own firewall).
R1.2) in radvd.conf, comment out "example of a standard prefix" prefix
{} block
R1.3) in radvd.conf, edit the line "prefix 0:0:0:1234::/64" and change
"1234" to a network number of your choice.
R1.4) in radvd.conf, edit line "Base6to4Interface ppp0" to reflect the
interface doing the 6to4 tunnelling (eth0 on my own firewall).
R2) add routing rules for the local network.
# ip -6 route add 2002:184a:9ba9:1010::/64 dev eth1
# ip -6 addr add 2002:184a:9ba9:1010::1 dev eth1
You cat get the 2002:... address (your 6to4 address, formed from your
ipv4 address) from your ifconfig. In this example, "eth1" is my local
LAN interface. eth0 is the interface to my ISP (DSL modem).
Here is what my ifconfig output looks like, after everything is set up
on my router/firewall:
eth0 Link encap:Ethernet HWaddr 00:00:21:DE:DE:B5
inet addr:24.74.155.XXX Bcast:255.255.255.255
Mask:255.255.248.0
inet6 addr: fe80::200:21ff:fede:deb5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8759136 errors:0 dropped:0 overruns:0 frame:0
TX packets:2238155 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1647432957 (1571.1 Mb) TX bytes:166256535 (158.5 Mb)
Interrupt:209 Base address:0x8c00
eth1 Link encap:Ethernet HWaddr 00:C0:9F:39:CD:B0
inet addr:10.10.10.1 Bcast:10.10.10.255 Mask:255.255.255.0
inet6 addr: 2002:184a:9ab9:110::1/128 Scope:Global
inet6 addr: 2002:184a:9ab9:110:2c0:9fff:fe39:cdb0/64 Scope:Global
inet6 addr: fe80::2c0:9fff:fe39:cdb0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:9073144 errors:0 dropped:0 overruns:0 frame:0
TX packets:10916350 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1820645725 (1736.3 Mb) TX bytes:3611957866 (3444.6
Base address:0xece0 Memory:fe3e0000-fe400000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:440 errors:0 dropped:0 overruns:0 frame:0
TX packets:440 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:54209 (52.9 Kb) TX bytes:54209 (52.9 Kb)
tun6to4 Link encap:IPv6-in-IPv4
inet6 addr: 2002:184a:9ab9::1/16 Scope:Global
UP RUNNING NOARP MTU:1480 Metric:1
RX packets:1520 errors:0 dropped:0 overruns:0 frame:0
TX packets:1614 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:886384 (865.6 Kb) TX bytes:224041 (218.7 Kb)
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: Trivial IPv6-for-Fedora HOWTO
2004-08-22 22:51 Trivial IPv6-for-Fedora HOWTO Jeff Garzik
@ 2004-08-22 23:08 ` Paul Fraser
2004-08-22 23:06 ` Alan Cox
2004-08-22 23:22 ` Jeff Garzik
0 siblings, 2 replies; 4+ messages in thread
From: Paul Fraser @ 2004-08-22 23:08 UTC (permalink / raw)
To: Jeff Garzik; +Cc: Netdev, Linux Kernel, David Woodhouse
You can also get an IPv6 tunnel at http://tunnelbroker.ipv6.net.au/ that
will give you your own IPv6 tunnel and allocation. This isn't just an
Australian site either - you can get either AU or US tunnels, and you
can apply and use it anywhere in the world.
Cheers,
Paul Fraser
paul@fraser.ipv6.net.au
Jeff Garzik wrote:
>
> So, thanks to David Woodhouse for showing me how to do this. IPv6
> appears to be very, very close to a Just Works(tm) state.
>
> These instructions are for Fedora Core 2 users, and describe how to set
> up IPv6 automatically tunnelling (6to4) on an IPv4 network. If you are
> stuck on an IPv4-only network (like most of us), this enables
> communication with IPv6 hosts quickly, easily, and transparently.
>
> (this HOWTO is archived at http://yyz.us/ipv6-fc2-howto.html)
>
>
> Simple setup:
>
> 1) Append to /etc/sysconfig/network
>
> NETWORKING_IPV6=yes
> IPV6_DEFAULTDEV=tun6to4
>
> 2) Append to /etc/sysconfig/ifcfg-eth0
>
> IPV6INIT=yes
> IPV6TO4INIT=yes
>
> 3) Reboot or restart your network interface.
>
> That's it!
>
>
>
> If you have an iptables ipv4 firewall, you'll want to
>
> F1) allow ipv6 tunnelled packets to pass through to ip6tables, by
> allowing protocol 41
>
> iptables -A block -p 41 -j ACCEPT
> ("block" is a custom chain on my firewall)
>
> F2) duplicate your ipv4 firewall rules for ipv6, using ip6tables. Some
> things, like masquerade, are not applicable to ipv6.
>
>
>
> If you have an ipv4 NATing firewall, which serves as a router for a
> local network, you'll want to set up radvd and routing rules, so that
> your hosts autoconfigure ipv6 automatically based on your router's
> advertisements, and also so that your hosts truly speak native ipv6
> without tunneling [the router does the tunnel wrap/unwrap].
>
> R1.1) in /etc/radvd.conf, set "interface ethX" to reflect your router's
> local LAN interface (eth1 on my own firewall).
>
> R1.2) in radvd.conf, comment out "example of a standard prefix" prefix
> {} block
>
> R1.3) in radvd.conf, edit the line "prefix 0:0:0:1234::/64" and change
> "1234" to a network number of your choice.
>
> R1.4) in radvd.conf, edit line "Base6to4Interface ppp0" to reflect the
> interface doing the 6to4 tunnelling (eth0 on my own firewall).
>
> R2) add routing rules for the local network.
>
> # ip -6 route add 2002:184a:9ba9:1010::/64 dev eth1
> # ip -6 addr add 2002:184a:9ba9:1010::1 dev eth1
>
> You cat get the 2002:... address (your 6to4 address, formed from your
> ipv4 address) from your ifconfig. In this example, "eth1" is my local
> LAN interface. eth0 is the interface to my ISP (DSL modem).
>
> Here is what my ifconfig output looks like, after everything is set up
> on my router/firewall:
>
> eth0 Link encap:Ethernet HWaddr 00:00:21:DE:DE:B5
> inet addr:24.74.155.XXX Bcast:255.255.255.255 Mask:255.255.248.0
> inet6 addr: fe80::200:21ff:fede:deb5/64 Scope:Link
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:8759136 errors:0 dropped:0 overruns:0 frame:0
> TX packets:2238155 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:1647432957 (1571.1 Mb) TX bytes:166256535 (158.5 Mb)
> Interrupt:209 Base address:0x8c00
>
> eth1 Link encap:Ethernet HWaddr 00:C0:9F:39:CD:B0
> inet addr:10.10.10.1 Bcast:10.10.10.255 Mask:255.255.255.0
> inet6 addr: 2002:184a:9ab9:110::1/128 Scope:Global
> inet6 addr: 2002:184a:9ab9:110:2c0:9fff:fe39:cdb0/64 Scope:Global
> inet6 addr: fe80::2c0:9fff:fe39:cdb0/64 Scope:Link
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:9073144 errors:0 dropped:0 overruns:0 frame:0
> TX packets:10916350 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:1820645725 (1736.3 Mb) TX bytes:3611957866 (3444.6
> Base address:0xece0 Memory:fe3e0000-fe400000
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> inet6 addr: ::1/128 Scope:Host
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:440 errors:0 dropped:0 overruns:0 frame:0
> TX packets:440 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:54209 (52.9 Kb) TX bytes:54209 (52.9 Kb)
>
> tun6to4 Link encap:IPv6-in-IPv4
> inet6 addr: 2002:184a:9ab9::1/16 Scope:Global
> UP RUNNING NOARP MTU:1480 Metric:1
> RX packets:1520 errors:0 dropped:0 overruns:0 frame:0
> TX packets:1614 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:886384 (865.6 Kb) TX bytes:224041 (218.7 Kb)
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: Trivial IPv6-for-Fedora HOWTO
2004-08-22 23:08 ` Paul Fraser
@ 2004-08-22 23:06 ` Alan Cox
2004-08-22 23:22 ` Jeff Garzik
1 sibling, 0 replies; 4+ messages in thread
From: Alan Cox @ 2004-08-22 23:06 UTC (permalink / raw)
To: Paul Fraser
Cc: Jeff Garzik, Netdev, Linux Kernel Mailing List, David Woodhouse
On Llu, 2004-08-23 at 00:08, Paul Fraser wrote:
> You can also get an IPv6 tunnel at http://tunnelbroker.ipv6.net.au/ that
> will give you your own IPv6 tunnel and allocation. This isn't just an
> Australian site either - you can get either AU or US tunnels, and you
> can apply and use it anywhere in the world.
Quite a few ISP's will do actual IPv6 or tunnels. In the UK anyone with
ADSL can switch provider to aaisp.net and get an IPv6 range and IPv6
tunnel for example.
Alan
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Trivial IPv6-for-Fedora HOWTO
2004-08-22 23:08 ` Paul Fraser
2004-08-22 23:06 ` Alan Cox
@ 2004-08-22 23:22 ` Jeff Garzik
1 sibling, 0 replies; 4+ messages in thread
From: Jeff Garzik @ 2004-08-22 23:22 UTC (permalink / raw)
To: Paul Fraser; +Cc: Netdev, Linux Kernel, David Woodhouse
Paul Fraser wrote:
> You can also get an IPv6 tunnel at http://tunnelbroker.ipv6.net.au/ that
> will give you your own IPv6 tunnel and allocation. This isn't just an
> Australian site either - you can get either AU or US tunnels, and you
> can apply and use it anywhere in the world.
Agreed, but the point of my post (and 6to4 in general) is that -- like
the general theme of IPv6 itself -- using 6to4 under Fedora Core 2 works
automatically. No need to worry about logging into a tunnel broker, and
no need to worry about traffic with other 6to4 sites being sub-optimally
routed.
Jeff
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2004-08-22 23:22 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-08-22 22:51 Trivial IPv6-for-Fedora HOWTO Jeff Garzik
2004-08-22 23:08 ` Paul Fraser
2004-08-22 23:06 ` Alan Cox
2004-08-22 23:22 ` Jeff Garzik
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).