Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Hans-Frieder Vogt]

[-- Attachment #1: Type: text/plain, Size: 1433 bytes --]

Am Montag, 13. September 2004 01:26 schrieben Sie:
> Hans-Frieder Vogt <hfvogt@arcor.de> :
> [2.6.9-rc1-bk11 r8169 freeze on amd64]
>
> > Until somebody comes up with a proper solution for this problem, I
> > suggest as a work-around to introduce a parameter so that the DAC can be
> > simply unselected if necessary, as outlined in the patch below.
> >
> > Thanks for any suggestions as to what the problem might be.
>
> Remove the workaround, apply the attached patch and watch the oops.
>
Francois,
thanks for your quick response.

I applied the patch to an otherwise clean 2.6.9-rc1-bk17, but no change to 
previous behaviour:
no oops (BUG_ON not triggered)! System boots up as normal, but just after I 
log in on the console the system freezes, i.e., keyboard does not react any 
more and the system is not accessible via network.
The time from the moment I log in to the time when the system freezes varies, 
but is in the order of 5s.
There is no difference whether NAPI is enabled or not.

My .config and the boot messages are attached to this e-mail.

Hans-Frieder

> If it happens in rtl8169_rx_interrupt(), you may notice that R12 is set to
> 0xbfc. R12 is pkt_len in rtl8169_rx_interrupt. This value is twice too
> high. I have not figured why so far and I'll go to bed.
>
> Please Cc: netdev and jgarzik@pobox.com on followup.
>
> --
> Ueimor

-- 
--
Hans-Frieder Vogt                 e-mail: hfvogt (at) arcor (dot) de

[-- Attachment #2: config-2.6.9-rc1-bk17 --]
[-- Type: text/plain, Size: 30970 bytes --]

#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.9-rc1-bk17-amd64
# Mon Sep 13 13:40:33 2004
#
CONFIG_X86_64=y
CONFIG_64BIT=y
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_X86_CMPXCHG=y
CONFIG_EARLY_PRINTK=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
CONFIG_GENERIC_ISA_DMA=y

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y

#
# General setup
#
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_BSD_PROCESS_ACCT_V3=y
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_HOTPLUG=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
CONFIG_KALLSYMS_EXTRA_PASS=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SHMEM=y
# CONFIG_TINY_SHMEM is not set

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y

#
# Processor type and features
#
CONFIG_MK8=y
# CONFIG_MPSC is not set
# CONFIG_GENERIC_CPU is not set
CONFIG_X86_L1_CACHE_BYTES=64
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
# CONFIG_MICROCODE is not set
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_MTRR=y
# CONFIG_SMP is not set
CONFIG_PREEMPT=y
CONFIG_GART_IOMMU=y
CONFIG_SWIOTLB=y
CONFIG_X86_MCE=y

#
# Power management options
#
CONFIG_PM=y
CONFIG_SOFTWARE_SUSPEND=y

#
# ACPI (Advanced Configuration and Power Interface) Support
#
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
# CONFIG_ACPI_AC is not set
# CONFIG_ACPI_BATTERY is not set
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_TOSHIBA is not set
CONFIG_ACPI_DEBUG=y
CONFIG_ACPI_BUS=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
# CONFIG_CPU_FREQ_PROC_INTF is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
# CONFIG_CPU_FREQ_24_API is not set
CONFIG_CPU_FREQ_TABLE=y

#
# CPUFreq processor drivers
#
CONFIG_X86_POWERNOW_K8=y
CONFIG_X86_POWERNOW_K8_ACPI=y
# CONFIG_X86_SPEEDSTEP_CENTRINO is not set
# CONFIG_X86_ACPI_CPUFREQ is not set

#
# Bus options (PCI etc.)
#
CONFIG_PCI=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
# CONFIG_UNORDERED_IO is not set
# CONFIG_PCI_MSI is not set
# CONFIG_PCI_LEGACY_PROC is not set
CONFIG_PCI_NAMES=y

#
# PCMCIA/CardBus support
#
# CONFIG_PCMCIA is not set

#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set

#
# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
CONFIG_IA32_EMULATION=y
# CONFIG_IA32_AOUT is not set
CONFIG_COMPAT=y
CONFIG_SYSVIPC_COMPAT=y
CONFIG_UID16=y

#
# Device Drivers
#

#
# Generic Driver Options
#
# CONFIG_STANDALONE is not set
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
CONFIG_FW_LOADER=m
# CONFIG_DEBUG_DRIVER is not set

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
# CONFIG_PARPORT_SERIAL is not set
CONFIG_PARPORT_PC_FIFO=y
CONFIG_PARPORT_PC_SUPERIO=y
# CONFIG_PARPORT_OTHER is not set
CONFIG_PARPORT_1284=y

#
# Plug and Play support
#

#
# Block devices
#
CONFIG_BLK_DEV_FD=m
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_LBD is not set

#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=m
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
# CONFIG_IDE_TASKFILE_IO is not set

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
CONFIG_BLK_DEV_ADMA=y
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
CONFIG_BLK_DEV_VIA82CXXX=y
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_IVB=y
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set

#
# SCSI Transport Attributes
#
CONFIG_SCSI_SPI_ATTRS=m
# CONFIG_SCSI_FC_ATTRS is not set

#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
CONFIG_SCSI_SATA=y
# CONFIG_SCSI_SATA_SVW is not set
# CONFIG_SCSI_ATA_PIIX is not set
# CONFIG_SCSI_SATA_NV is not set
CONFIG_SCSI_SATA_PROMISE=y
# CONFIG_SCSI_SATA_SX4 is not set
# CONFIG_SCSI_SATA_SIL is not set
# CONFIG_SCSI_SATA_SIS is not set
CONFIG_SCSI_SATA_VIA=y
# CONFIG_SCSI_SATA_VITESSE is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
CONFIG_SCSI_SYM53C8XX_2=m
CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=0
CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16
CONFIG_SCSI_SYM53C8XX_MAX_TAGS=256
# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=y
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_QLA6322 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_DEBUG is not set

#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set

#
# Fusion MPT device support
#
# CONFIG_FUSION is not set

#
# IEEE 1394 (FireWire) support
#
CONFIG_IEEE1394=m

#
# Subsystem Options
#
# CONFIG_IEEE1394_VERBOSEDEBUG is not set
# CONFIG_IEEE1394_OUI_DB is not set
# CONFIG_IEEE1394_EXTRA_CONFIG_ROMS is not set

#
# Device Drivers
#
# CONFIG_IEEE1394_PCILYNX is not set
CONFIG_IEEE1394_OHCI1394=m

#
# Protocol Drivers
#
CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set
# CONFIG_IEEE1394_ETH1394 is not set
# CONFIG_IEEE1394_DV1394 is not set
CONFIG_IEEE1394_RAWIO=m
# CONFIG_IEEE1394_CMP is not set

#
# I2O device support
#
# CONFIG_I2O is not set

#
# Networking support
#
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=m
CONFIG_PACKET_MMAP=y
# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
CONFIG_NET_KEY=m
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
CONFIG_INET_TUNNEL=m

#
# IP: Virtual Server Configuration
#
# CONFIG_IP_VS is not set
CONFIG_IPV6=m
CONFIG_IPV6_PRIVACY=y
CONFIG_INET6_AH=m
CONFIG_INET6_ESP=m
CONFIG_INET6_IPCOMP=m
CONFIG_INET6_TUNNEL=m
CONFIG_IPV6_TUNNEL=m
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set

#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
# CONFIG_IP_NF_CT_ACCT is not set
CONFIG_IP_NF_CT_PROTO_SCTP=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_PKTTYPE=m
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_HELPER=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_REALM=m
CONFIG_IP_NF_MATCH_SCTP=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
# CONFIG_IP_NF_NAT_LOCAL is not set
CONFIG_IP_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_CLASSIFY=m
CONFIG_IP_NF_RAW=m
# CONFIG_IP_NF_TARGET_NOTRACK is not set
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
# CONFIG_IP_NF_COMPAT_IPCHAINS is not set
# CONFIG_IP_NF_COMPAT_IPFWADM is not set

#
# IPv6: Netfilter Configuration
#
CONFIG_IP6_NF_QUEUE=m
CONFIG_IP6_NF_IPTABLES=m
CONFIG_IP6_NF_MATCH_LIMIT=m
CONFIG_IP6_NF_MATCH_MAC=m
CONFIG_IP6_NF_MATCH_RT=m
CONFIG_IP6_NF_MATCH_OPTS=m
CONFIG_IP6_NF_MATCH_FRAG=m
CONFIG_IP6_NF_MATCH_HL=m
CONFIG_IP6_NF_MATCH_MULTIPORT=m
CONFIG_IP6_NF_MATCH_OWNER=m
CONFIG_IP6_NF_MATCH_MARK=m
CONFIG_IP6_NF_MATCH_IPV6HEADER=m
CONFIG_IP6_NF_MATCH_AHESP=m
CONFIG_IP6_NF_MATCH_LENGTH=m
CONFIG_IP6_NF_MATCH_EUI64=m
CONFIG_IP6_NF_FILTER=m
CONFIG_IP6_NF_TARGET_LOG=m
CONFIG_IP6_NF_MANGLE=m
CONFIG_IP6_NF_TARGET_MARK=m
CONFIG_IP6_NF_RAW=m
CONFIG_XFRM=y
CONFIG_XFRM_USER=m

#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_HW_FLOWCONTROL is not set

#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
CONFIG_NET_CLS_ROUTE=y

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_HAMRADIO is not set
CONFIG_IRDA=m

#
# IrDA protocols
#
CONFIG_IRLAN=m
CONFIG_IRNET=m
CONFIG_IRCOMM=m
# CONFIG_IRDA_ULTRA is not set

#
# IrDA options
#
CONFIG_IRDA_CACHE_LAST_LSAP=y
CONFIG_IRDA_FAST_RR=y
# CONFIG_IRDA_DEBUG is not set

#
# Infrared-port device drivers
#

#
# SIR device drivers
#
CONFIG_IRTTY_SIR=m

#
# Dongle support
#
# CONFIG_DONGLE is not set

#
# Old SIR device drivers
#
CONFIG_IRPORT_SIR=m

#
# Old Serial dongle support
#
# CONFIG_DONGLE_OLD is not set

#
# FIR device drivers
#
CONFIG_USB_IRDA=m
# CONFIG_SIGMATEL_FIR is not set
# CONFIG_VLSI_FIR is not set
# CONFIG_BT is not set
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set

#
# ARCnet devices
#
# CONFIG_ARCNET is not set

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=m
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set

#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
# CONFIG_DGRS is not set
# CONFIG_EEPRO100 is not set
# CONFIG_E100 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_8139CP is not set
CONFIG_8139TOO=m
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_8139_OLD_RX_RESET is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_VIA_VELOCITY is not set

#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
CONFIG_R8169=m
CONFIG_R8169_NAPI=y
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set

#
# Ethernet (10000 Mbit)
#
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set

#
# Token Ring devices
#
# CONFIG_TR is not set

#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set

#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=m
# CONFIG_PPP_MULTILINK is not set
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPPOE=m
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set

#
# ISDN subsystem
#
# CONFIG_ISDN is not set

#
# Telephony Support
#
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=m
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=m
# CONFIG_INPUT_EVBUG is not set

#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
# CONFIG_SERIO_PCIPS2 is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=m
CONFIG_SERIAL_8250_ACPI=y
CONFIG_SERIAL_8250_NR_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=m
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
CONFIG_PPDEV=m
# CONFIG_TIPAR is not set

#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_NVRAM=m
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set

#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=y
CONFIG_AGP_AMD64=y
# CONFIG_AGP_INTEL_MCH is not set
# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HPET is not set
CONFIG_HANGCHECK_TIMER=y

#
# I2C support
#
CONFIG_I2C=m
CONFIG_I2C_CHARDEV=m

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=m
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set

#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
CONFIG_I2C_ISA=m
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_VIA is not set
CONFIG_I2C_VIAPRO=m
# CONFIG_I2C_VOODOO3 is not set
# CONFIG_I2C_PCA_ISA is not set

#
# Hardware Sensors Chip support
#
CONFIG_I2C_SENSOR=m
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83L785TS is not set
CONFIG_SENSORS_W83627HF=m

#
# Other I2C Chip support
#
CONFIG_SENSORS_EEPROM=m
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set

#
# Misc devices
#
# CONFIG_IBM_ASM is not set

#
# Multimedia devices
#
CONFIG_VIDEO_DEV=m

#
# Video For Linux
#

#
# Video Adapters
#
CONFIG_VIDEO_BT848=m
# CONFIG_VIDEO_BWQCAM is not set
# CONFIG_VIDEO_CQCAM is not set
# CONFIG_VIDEO_W9966 is not set
# CONFIG_VIDEO_CPIA is not set
# CONFIG_VIDEO_SAA5246A is not set
# CONFIG_VIDEO_SAA5249 is not set
# CONFIG_TUNER_3036 is not set
# CONFIG_VIDEO_STRADIS is not set
# CONFIG_VIDEO_ZORAN is not set
# CONFIG_VIDEO_SAA7134 is not set
# CONFIG_VIDEO_MXB is not set
# CONFIG_VIDEO_DPC is not set
# CONFIG_VIDEO_HEXIUM_ORION is not set
# CONFIG_VIDEO_HEXIUM_GEMINI is not set
# CONFIG_VIDEO_CX88 is not set
# CONFIG_VIDEO_OVCAMCHIP is not set

#
# Radio Adapters
#
# CONFIG_RADIO_GEMTEK_PCI is not set
# CONFIG_RADIO_MAXIRADIO is not set
# CONFIG_RADIO_MAESTRO is not set

#
# Digital Video Broadcasting Devices
#
CONFIG_DVB=y
CONFIG_DVB_CORE=m

#
# Supported Frontend Modules
#
# CONFIG_DVB_TWINHAN_DST is not set
# CONFIG_DVB_STV0299 is not set
CONFIG_DVB_SP887X=m
CONFIG_DVB_SP887X_FIRMWARE_FILE="/usr/lib/hotplug/firmware/sc_main.mc"
# CONFIG_DVB_ALPS_TDLB7 is not set
# CONFIG_DVB_ALPS_TDMB7 is not set
# CONFIG_DVB_ATMEL_AT76C651 is not set
# CONFIG_DVB_CX24110 is not set
# CONFIG_DVB_GRUNDIG_29504_491 is not set
# CONFIG_DVB_GRUNDIG_29504_401 is not set
# CONFIG_DVB_MT312 is not set
# CONFIG_DVB_VES1820 is not set
# CONFIG_DVB_VES1X93 is not set
# CONFIG_DVB_TDA1004X is not set
# CONFIG_DVB_NXT6000 is not set

#
# Supported SAA7146 based PCI Adapters
#
# CONFIG_DVB_AV7110 is not set
# CONFIG_DVB_BUDGET is not set
# CONFIG_DVB_BUDGET_CI is not set
# CONFIG_DVB_BUDGET_AV is not set

#
# Supported USB Adapters
#
# CONFIG_DVB_TTUSB_BUDGET is not set
CONFIG_DVB_TTUSB_DEC=m

#
# Supported FlexCopII (B2C2) Adapters
#
# CONFIG_DVB_B2C2_SKYSTAR is not set

#
# Supported BT878 Adapters
#
CONFIG_DVB_BT8XX=m
CONFIG_VIDEO_TUNER=m
CONFIG_VIDEO_BUF=m
CONFIG_VIDEO_BTCX=m
CONFIG_VIDEO_IR=m

#
# Graphics support
#
CONFIG_FB=y
# CONFIG_FB_MODE_HELPERS is not set
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
CONFIG_FB_VESA=y
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_VIRTUAL is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y

#
# Logo configuration
#
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y

#
# Sound
#
CONFIG_SOUND=m

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
CONFIG_SND_HWDEP=m
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=m
CONFIG_SND_SEQ_DUMMY=m
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_BIT32_EMUL=m
CONFIG_SND_RTCTIMER=m
CONFIG_SND_VERBOSE_PRINTK=y
# CONFIG_SND_DEBUG is not set

#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
# CONFIG_SND_DUMMY is not set
CONFIG_SND_VIRMIDI=m
# CONFIG_SND_MTPAV is not set
CONFIG_SND_SERIAL_U16550=m
CONFIG_SND_MPU401=m

#
# PCI devices
#
CONFIG_SND_AC97_CODEC=m
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_INTEL8X0M is not set
# CONFIG_SND_SONICVIBES is not set
CONFIG_SND_VIA82XX=m
# CONFIG_SND_VX222 is not set

#
# ALSA USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set

#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set

#
# USB support
#
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_BANDWIDTH=y
CONFIG_USB_DYNAMIC_MINORS=y
CONFIG_USB_SUSPEND=y
# CONFIG_USB_OTG is not set

#
# USB Host Controller Drivers
#
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_EHCI_SPLIT_ISO=y
# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
# CONFIG_USB_OHCI_HCD is not set
CONFIG_USB_UHCI_HCD=m

#
# USB Device Class drivers
#
CONFIG_USB_AUDIO=m
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_MIDI is not set
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
CONFIG_USB_STORAGE=m
CONFIG_USB_STORAGE_DEBUG=y
CONFIG_USB_STORAGE_RW_DETECT=y
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_HP8200e=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y

#
# USB Human Interface Devices (HID)
#
CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT=y
# CONFIG_HID_FF is not set
CONFIG_USB_HIDDEV=y

#
# USB HID Boot Protocol drivers
#
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set

#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
# CONFIG_USB_VICAM is not set
# CONFIG_USB_DSBR is not set
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_KONICAWC is not set
# CONFIG_USB_OV511 is not set
# CONFIG_USB_SE401 is not set
# CONFIG_USB_SN9C102 is not set
# CONFIG_USB_STV680 is not set

#
# USB Network adaptors
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set

#
# USB port drivers
#
# CONFIG_USB_USS720 is not set

#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_TIGL is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETSERVO is not set
# CONFIG_USB_TEST is not set

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set

#
# Firmware Drivers
#
# CONFIG_EDD is not set

#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
# CONFIG_EXT2_FS_SECURITY is not set
CONFIG_EXT3_FS=m
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=m
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
CONFIG_REISERFS_FS_XATTR=y
CONFIG_REISERFS_FS_POSIX_ACL=y
# CONFIG_REISERFS_FS_SECURITY is not set
CONFIG_JFS_FS=m
CONFIG_JFS_POSIX_ACL=y
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=y
# CONFIG_XFS_RT is not set
# CONFIG_XFS_QUOTA is not set
# CONFIG_XFS_SECURITY is not set
CONFIG_XFS_POSIX_ACL=y
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=m
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
# CONFIG_DEVFS_FS is not set
CONFIG_DEVPTS_FS_XATTR=y
# CONFIG_DEVPTS_FS_SECURITY is not set
CONFIG_TMPFS=y
CONFIG_HUGETLBFS=y
CONFIG_HUGETLB_PAGE=y
CONFIG_RAMFS=y

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Network File Systems
#
# CONFIG_NFS_FS is not set
# CONFIG_NFSD is not set
# CONFIG_EXPORTFS is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y

#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=m
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
CONFIG_NLS_ASCII=m
CONFIG_NLS_ISO8859_1=m
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
CONFIG_NLS_ISO8859_5=m
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=m

#
# Profiling support
#
# CONFIG_PROFILING is not set

#
# Kernel hacking
#
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_INFO is not set
# CONFIG_FRAME_POINTER is not set
# CONFIG_CHECKING is not set
# CONFIG_INIT_DEBUG is not set
# CONFIG_SCHEDSTATS is not set
# CONFIG_IOMMU_DEBUG is not set

#
# Security options
#
# CONFIG_SECURITY is not set

#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
CONFIG_CRYPTO_WHIRLPOOL=m
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
CONFIG_CRYPTO_TEA=m
CONFIG_CRYPTO_ARC4=m
CONFIG_CRYPTO_KHAZAD=m
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
# CONFIG_CRYPTO_TEST is not set

#
# Library routines
#
CONFIG_CRC_CCITT=m
CONFIG_CRC32=m
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m

[-- Attachment #3: boot.msg-napi --]
[-- Type: text/plain, Size: 15403 bytes --]

root=/dev/sda2 apic vga=792 resume=/dev/sda1 console=tty0
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 2000.089 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 1026304k/1048512k available (2218k kernel code, 21412k reserved, 1013k data, 144k init)
Calibrating delay loop... 3940.35 BogoMIPS (lpj=1970176)
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 08
 tbxface-0117 [02] acpi_load_tables      : ACPI Tables successfully acquired
Parsing all Control Methods:.....................................................................................................................................................
Table [DSDT](id F004) - 520 Objects with 48 Devices 149 Methods 26 Regions
ACPI Namespace successfully loaded at root ffffffff804486e0
evxfevnt-0093 [03] acpi_enable           : Transition to ACPI mode successful
Using local APIC NMI watchdog using perfctr0
ENABLING IO-APIC IRQs
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
Detected 12.500 MHz APIC timer.
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040715
evgpeblk-0980 [07] ev_create_gpe_block   : GPE 00 to 0F [_GPE] 2 regs at 0000000000000820 on int 0x9
evgpeblk-0989 [07] ev_create_gpe_block   : Found 6 Wake, Enabled 0 Runtime GPEs in this block
Completing Region/Field/Buffer/Package initialization:...........................................................................................
Initialized 26/26 Regions 9/9 Fields 44/44 Buffers 12/24 Packages (529 nodes)
Executing all Device _STA and_INI methods:...................................................
51 Devices found containing: 51 _STA, 1 _INI methods
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xa9 -> IRQ 19 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI interrupt 0000:00:08.1[A] -> GSI 19 (level, low) -> IRQ 19
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xb1 -> IRQ 16 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-20 -> 0xb9 -> IRQ 20 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
IOAPIC[0]: Set PCI routing entry (2-21 -> 0xc1 -> IRQ 21 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
IOAPIC[0]: Set PCI routing entry (2-22 -> 0xc9 -> IRQ 22 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 22
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
.......    : physical APIC id: 02
.... register #01: 00178003
.......     : max redirection entries: 0017
.......     : PRQ implemented: 1
.......     : IO APIC version: 0003
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
 00 000 00  1    0    0   0   0    0    0    00
 01 001 01  0    0    0   0   0    1    1    39
 02 001 01  0    0    0   0   0    1    1    31
 03 001 01  0    0    0   0   0    1    1    41
 04 001 01  0    0    0   0   0    1    1    49
 05 001 01  0    0    0   0   0    1    1    51
 06 001 01  0    0    0   0   0    1    1    59
 07 001 01  0    0    0   0   0    1    1    61
 08 001 01  0    0    0   0   0    1    1    69
 09 001 01  0    1    0   1   0    1    1    71
 0a 001 01  0    0    0   0   0    1    1    79
 0b 001 01  0    0    0   0   0    1    1    81
 0c 001 01  0    0    0   0   0    1    1    89
 0d 001 01  0    0    0   0   0    1    1    91
 0e 001 01  0    0    0   0   0    1    1    99
 0f 001 01  0    0    0   0   0    1    1    A1
 10 001 01  1    1    0   1   0    1    1    B1
 11 000 00  1    0    0   0   0    0    0    00
 12 000 00  1    0    0   0   0    0    0    00
 13 001 01  1    1    0   1   0    1    1    A9
 14 001 01  1    1    0   1   0    1    1    B9
 15 001 01  1    1    0   1   0    1    1    C1
 16 001 01  1    1    0   1   0    1    1    C9
 17 041 01  1    0    0   0   0    0    2    DA
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
.................................... done.
agpgart: Detected AGP bridge 0
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: AGP aperture is 128M @ 0xd0000000
PCI-DMA: Disabling IOMMU.
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Total HugeTLB memory allocated, 0
SGI XFS with ACLs, large block/inode numbers, no debug enabled
Initializing Cryptographic API
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 5
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 5
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 5
PCI: Via IRQ fixup for 0000:00:10.3, from 10 to 5
vesafb: framebuffer at 0xc0000000, mapped to 0xffffff0000100000, size 6144k
vesafb: mode is 1024x768x32, linelength=4096, pages=1
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU1] (supports C1)
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
Hangcheck: starting hangcheck timer 0.5.0 (tick is 180 seconds, margin is 60 seconds).
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 20
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: ATAPI DVD DUAL 8X4X12, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
ide2: Wait for ready failed before probe !
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
libata version 1.02 loaded.
sata_via version 0.20
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 20
sata_via(0000:00:0f.0): routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE802 bmdma 0xDC00 irq 20
ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE002 bmdma 0xDC08 irq 20
ata1: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:203f
ata1: dev 0 ATA, max UDMA/100, 312581808 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_via
ata2: no device found (phy stat 00000000)
scsi1 : sata_via
  Vendor: ATA       Model: WDC WD1600JD-00F  Rev: 02.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.00.09b)
acpi_utils-0071 [65] acpi_extract_package  : Invalid 'package' argument
acpi_processor-1008 [64] acpi_processor_get_per: Invalid _PSS data
powernow-k8:    0 : fid 0x0 (800 MHz), vid 0xa (1300 mV)
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x6 (1400 mV)
powernow-k8:    2 : fid 0xc (2000 MHz), vid 0x2 (1500 mV)
powernow-k8: cpu_init done, current fid 0xc, vid 0x2
Resume Machine: resuming from /dev/sda1
Resuming from device unknown-block(8,1)
Resume Machine: This is normal swap space
ACPI: (supports S0 S3 S4 S5)
ACPI wakeup devices: 
PCI0 UAR1 USB1 USB2 USB3 USB4 EHCI USBD  AC9  MC9 ILAN SLPB 
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 144k freed
Adding 2112508k swap on /dev/sda1.  Priority:-1 extents:1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
IOAPIC[0]: Set PCI routing entry (2-4 -> 0x49 -> IRQ 4 Mode:0 Active:0)
hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
inserting floppy driver for 2.6.9-rc1-bk17-amd64
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
lp: driver loaded but no devices found
i2c /dev entries driver
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 19
bttv0: Bt878 (rev 17) at 0000:00:08.0, irq: 19, latency: 32, mmio: 0xcddfe000
bttv0: detected: AverMedia AverTV DVB-T [card=124], PCI subsystem ID is 1461:0761
bttv0: using: AverMedia AverTV DVB-T 761 [card=124,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=009c008d [init]
bttv0: using tuner=-1
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: add subdevice "remote0"
bttv0: add subdevice "dvb0"
XFS mounting filesystem sda5
Ending clean XFS mount for filesystem: sda5
XFS mounting filesystem sda6
Ending clean XFS mount for filesystem: sda6
XFS mounting filesystem sda7
Ending clean XFS mount for filesystem: sda7
XFS mounting filesystem sda8
Ending clean XFS mount for filesystem: sda8
XFS mounting filesystem sda9
Ending clean XFS mount for filesystem: sda9
XFS mounting filesystem sda10
Ending clean XFS mount for filesystem: sda10
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI interrupt 0000:00:08.1[A] -> GSI 19 (level, low) -> IRQ 19
bt878(0): Bt878 (rev 17) at 00:08.1, irq: 19, latency: 32, memory: 0xcddff000
r8169 Gigabit Ethernet driver 1.2 loaded
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 16
r8169: NAPI enabled
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xffffff0000014f00, 00:0c:76:5c:f1:f6, IRQ 16
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:10.0: irq 21, io base 000000000000c400
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:10.1: irq 21, io base 000000000000c800
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:10.2: irq 21, io base 000000000000cc00
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4)
uhci_hcd 0000:00:10.3: irq 21, io base 000000000000d000
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-2: new low speed USB device using address 2
usbcore: registered new driver hiddev
ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:00:10.4: irq 21, pci mem ffffff0000016d00
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
drivers/usb/input/hid-core.c: ctrl urb status -84 received
input: USB HID v1.00 Mouse [Logitech Inc. iFeel MouseMan] on usb-0000:00:10.1-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 2-2: USB disconnect, address 2
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:11.5 to 64
usb 2-2: new low speed USB device using address 3
drivers/usb/input/hid-core.c: ctrl urb status -2 received
drivers/usb/input/hid-core.c: timeout initializing reports

input: USB HID v1.00 Mouse [Logitech Inc. iFeel MouseMan] on usb-0000:00:10.1-2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
r8169: eth0: link up
ttyS1: LSR safety check engaged!
ttyS1: LSR safety check engaged!
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff803ec680(lo)
IPv6 over IPv4 tunneling driver

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Francois Romieu]

Hans-Frieder Vogt <hfvogt@arcor.de> :
[...]
> no oops (BUG_ON not triggered)! System boots up as normal, but just after I 

...

> log in on the console the system freezes, i.e., keyboard does not react any 
> more and the system is not accessible via network.

- do the keyboard leds or the magic sysrq answer (I assume you boot without X) ?
- does it make a difference if you boot with the network cable unpluged (i.e.
  fine until pluged then dead when first packet comes in) ?

> The time from the moment I log in to the time when the system freezes varies, 
> but is in the order of 5s.

First packet probably. Can you verify this point ?

> There is no difference whether NAPI is enabled or not.

I will welcome lspci -vx + gcc version + objdump -S of the r8169 module.

--
Ueimor

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Hans-Frieder Vogt]

[-- Attachment #1: Type: text/plain, Size: 1927 bytes --]

Am Dienstag, 14. September 2004 00:02 schrieb Francois Romieu:
> Hans-Frieder Vogt <hfvogt@arcor.de> :
> [...]
>
> > no oops (BUG_ON not triggered)! System boots up as normal, but just after
> > I
>
> ...
>
> > log in on the console the system freezes, i.e., keyboard does not react
> > any more and the system is not accessible via network.
>
> - do the keyboard leds or the magic sysrq answer (I assume you boot without  
X) ?

(To be able to exclude any side effect of X, I have booted without X and I 
have also removed all graphics driver related modules)

When the system freezes, the keyboard is completely dead, the LEDs do not 
react any more and also the sysrq keys do not work.

> - does it make a difference if you boot with the network cable 
> unpluged (i.e. fine until pluged then dead when first packet comes in) ?
>

YES!! With the network cable unplugged, the system does not freeze!
Every 10 seconds, I get now the message:
r8169: eth0: PHY reset until link up
but otherwise everything seems fine.

> > The time from the moment I log in to the time when the system freezes
> > varies, but is in the order of 5s.
>
> First packet probably. Can you verify this point ?
>

I think the test with the network cable unplugged supports this assumption.
With network cable unplugged, /proc/interrupts shows 0 interrupts for the 
network card, so probably the first interrupt leads to the system freeze.

> > There is no difference whether NAPI is enabled or not.
>
> I will welcome lspci -vx + gcc version + objdump -S of the r8169 module.
>

lspci -vx and objdump -S output (gzipped) are attached, gcc version is 3.4.2 
(Debian 3.4.2-2), but no visible difference with 3.4.1.

> --
> Ueimor

Thanks for your help, Francois.
I will put a few printks into the interrupt routine and hope to be able to 
tell you more tomorrow,

Hans-Frieder

-- 
--
Hans-Frieder Vogt                 e-mail: hfvogt (at) arcor (dot) de

[-- Attachment #2: lspci-vx.out --]
[-- Type: text/plain, Size: 9600 bytes --]

0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge (rev 01)
	Subsystem: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge
	Flags: bus master, 66MHz, medium devsel, latency 8
	Memory at d0000000 (32-bit, prefetchable) [size=128M]
	Capabilities: [80] AGP version 3.0
	Capabilities: [c0] #08 [0060]
	Capabilities: [68] Power Management version 2
	Capabilities: [58] #08 [8001]
00: 06 11 88 31 06 00 30 22 01 00 00 06 00 08 00 00
10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 88 31
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00

0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800 South] (prog-if 00 [Normal decode])
	Flags: bus master, 66MHz, medium devsel, latency 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	Memory behind bridge: cde00000-cfefffff
	Prefetchable memory behind bridge: bdd00000-cdcfffff
	Capabilities: [80] Power Management version 2
00: 06 11 88 b1 07 01 30 02 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 f0 00 20 22
20: e0 cd e0 cf d0 bd c0 cd 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0e 00

0000:00:08.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
	Subsystem: Avermedia Technologies Inc: Unknown device 0761
	Flags: bus master, medium devsel, latency 32, IRQ 19
	Memory at cddfe000 (32-bit, prefetchable) [size=4K]
	Capabilities: [44] Vital Product Data
	Capabilities: [4c] Power Management version 2
00: 9e 10 6e 03 06 00 90 02 11 00 00 04 00 20 80 00
10: 08 e0 df cd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 61 14 61 07
30: 00 00 00 00 44 00 00 00 00 00 00 00 0c 01 10 28

0000:00:08.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
	Subsystem: Avermedia Technologies Inc: Unknown device 0761
	Flags: bus master, medium devsel, latency 32, IRQ 19
	Memory at cddff000 (32-bit, prefetchable) [size=4K]
	Capabilities: [44] Vital Product Data
	Capabilities: [4c] Power Management version 2
00: 9e 10 78 08 06 00 90 02 11 00 80 04 00 20 80 00
10: 08 f0 df cd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 61 14 61 07
30: 00 00 00 00 44 00 00 00 00 00 00 00 0c 01 04 ff

0000:00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 702c
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
	I/O ports at d400 [size=256]
	Memory at cfffbf00 (32-bit, non-prefetchable) [size=256]
	Expansion ROM at 40000000 [disabled] [size=128K]
	Capabilities: [dc] Power Management version 2
00: ec 10 69 81 17 00 b0 02 10 00 00 02 10 40 00 00
10: 01 d4 00 00 00 bf ff cf 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 2c 70
30: 00 00 00 40 dc 00 00 00 00 00 00 00 0b 01 20 40

0000:00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
	Subsystem: Micro-Star International Co., Ltd. MSI Neo K8T FIS2R mainboard
	Flags: bus master, medium devsel, latency 32, IRQ 20
	I/O ports at ec00 [size=8]
	I/O ports at e800 [size=4]
	I/O ports at e400 [size=8]
	I/O ports at e000 [size=4]
	I/O ports at dc00 [size=16]
	I/O ports at d800 [size=256]
	Capabilities: [c0] Power Management version 2
00: 06 11 49 31 07 00 90 02 80 00 04 01 00 20 80 00
10: 01 ec 00 00 01 e8 00 00 01 e4 00 00 01 e0 00 00
20: 01 dc 00 00 01 d8 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 c0 00 00 00 00 00 00 00 0a 02 00 00

0000:00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 7020
	Flags: bus master, medium devsel, latency 32, IRQ 20
	I/O ports at fc00 [size=16]
	Capabilities: [c0] Power Management version 2
00: 06 11 71 05 07 00 90 02 06 8a 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 fc 00 00 00 00 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 01 00 00

0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 7020
	Flags: bus master, medium devsel, latency 32, IRQ 21
	I/O ports at c400 [size=32]
	Capabilities: [80] Power Management version 2
00: 06 11 38 30 17 00 10 02 81 00 03 0c 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 c4 00 00 00 00 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 01 00 00

0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 7020
	Flags: bus master, medium devsel, latency 32, IRQ 21
	I/O ports at c800 [size=32]
	Capabilities: [80] Power Management version 2
00: 06 11 38 30 17 00 10 02 81 00 03 0c 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 c8 00 00 00 00 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 01 00 00

0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 7020
	Flags: bus master, medium devsel, latency 32, IRQ 21
	I/O ports at cc00 [size=32]
	Capabilities: [80] Power Management version 2
00: 06 11 38 30 17 00 10 02 81 00 03 0c 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 cc 00 00 00 00 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 02 00 00

0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81) (prog-if 00 [UHCI])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 7020
	Flags: bus master, medium devsel, latency 32, IRQ 21
	I/O ports at d000 [size=32]
	Capabilities: [80] Power Management version 2
00: 06 11 38 30 17 00 10 02 81 00 03 0c 08 20 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d0 00 00 00 00 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 02 00 00

0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if 20 [EHCI])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 7020
	Flags: bus master, medium devsel, latency 32, IRQ 21
	Memory at cfffbd00 (32-bit, non-prefetchable) [size=256]
	Capabilities: [80] Power Management version 2
00: 06 11 04 31 17 00 10 02 86 20 03 0c 10 20 80 00
10: 00 bd ff cf 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 20 70
30: 00 00 00 00 80 00 00 00 00 00 00 00 05 03 00 00

0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [K8T800 South]
	Subsystem: VIA Technologies, Inc. VT8237 ISA bridge [K8T800 South]
	Flags: bus master, stepping, medium devsel, latency 0
	Capabilities: [c0] Power Management version 2
00: 06 11 27 32 87 00 10 02 00 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 27 32
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00

0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0080
	Flags: medium devsel, IRQ 22
	I/O ports at c000 [size=256]
	Capabilities: [c0] Power Management version 2
00: 06 11 59 30 01 00 10 02 60 00 01 04 00 00 00 00
10: 01 c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 62 14 80 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 05 03 00 00

0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
	Flags: fast devsel
	Capabilities: [80] #08 [2101]
00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00

0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
	Flags: fast devsel
00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
	Flags: fast devsel
00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
	Flags: fast devsel
00: 22 10 03 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

0000:01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev a1) (prog-if 00 [VGA])
	Subsystem: Hercules: Unknown device 0020
	Flags: bus master, 66MHz, medium devsel, latency 248, IRQ 16
	Memory at ce000000 (32-bit, non-prefetchable) [size=16M]
	Memory at c0000000 (32-bit, prefetchable) [size=128M]
	Expansion ROM at cfef0000 [disabled] [size=64K]
	Capabilities: [60] Power Management version 2
	Capabilities: [44] AGP version 2.0
00: de 10 10 01 07 00 b0 02 a1 00 00 03 00 f8 00 00
10: 00 00 00 ce 08 00 00 c0 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 81 16 20 00
30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 05 01


[-- Attachment #3: r8169-dump.out.gz --]
[-- Type: application/x-gzip, Size: 25574 bytes --]

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Hans-Frieder Vogt]

Francois,

I did a few tests with the r8169 driver on my x86-64 system:

with DAC enabled (as is default),
the first interrupt is a read interrupt, because the status read from 
IntrStatus is 0x8001, i.e. SYSErr | RxOK.
So, a PCI error did occur, which is strange.
Because of the RxOK bit, rtl8169_rx_interrupt is called. In this routine,
tp->cur_rx is 0
tp->dirty_rx is 0
tp->RxDescArray[entry].status is 0,
which then gives a pkt_size of -4!
The system freezes somewhere in rtl8169_rx_interrupt.

When I do a
if (pkt_size < 0) break;
in rtl8169_rx_interrupt to block the errorneous pkt_size, the system still 
freezes, but AFTER LEAVING the interrupt routine rtl8169_interrupt.

Same, when I introduced a shortcut to get rid of the SYSErr.

For comparison:
When I switch off DAC, then the first interrupts are
1: IntrStatus: 0x0484 (? | TxDescUnavail?), -> tx interrupt
2: IntrStatus: 0x0484, -> tx interrupt
3: IntrStatus: 0x0485, -> rx interrupt
...

Just another thought:
Of course x86-64 has the address-space that enables >4GB RAM, and x86-64 
always supports DAC (as stated in include/asm-x86_64/pci.h), but I have 
currently only 1GB RAM, so, strictly speaking, DAC is not really necessary. 
Strange enough, the latest Realtek driver 2.2 does not even support DAC (only 
the lower 32 bit of the DMA-Addresses are written to the registers).
Could it be that the Realtek driver does not support DAC for a good reason?

Anyway, I will continue searching for the problem...

Hans-Frieder

Am Dienstag, 14. September 2004 01:31 schrieb Hans-Frieder Vogt:
> Am Dienstag, 14. September 2004 00:02 schrieb Francois Romieu:
> > Hans-Frieder Vogt <hfvogt@arcor.de> :
> > [...]
> >
> > > no oops (BUG_ON not triggered)! System boots up as normal, but just
> > > after I
> >
> > ...
> >
> > > log in on the console the system freezes, i.e., keyboard does not react
> > > any more and the system is not accessible via network.
> >
> > - do the keyboard leds or the magic sysrq answer (I assume you boot
> > without
>
> X) ?
>
> (To be able to exclude any side effect of X, I have booted without X and I
> have also removed all graphics driver related modules)
>
> When the system freezes, the keyboard is completely dead, the LEDs do not
> react any more and also the sysrq keys do not work.
>
> > - does it make a difference if you boot with the network cable
> > unpluged (i.e. fine until pluged then dead when first packet comes in) ?
>
> YES!! With the network cable unplugged, the system does not freeze!
> Every 10 seconds, I get now the message:
> r8169: eth0: PHY reset until link up
> but otherwise everything seems fine.
>
> > > The time from the moment I log in to the time when the system freezes
> > > varies, but is in the order of 5s.
> >
> > First packet probably. Can you verify this point ?
>
> I think the test with the network cable unplugged supports this assumption.
> With network cable unplugged, /proc/interrupts shows 0 interrupts for the
> network card, so probably the first interrupt leads to the system freeze.
>
> > > There is no difference whether NAPI is enabled or not.
> >
> > I will welcome lspci -vx + gcc version + objdump -S of the r8169 module.
>
> lspci -vx and objdump -S output (gzipped) are attached, gcc version is
> 3.4.2 (Debian 3.4.2-2), but no visible difference with 3.4.1.
>
> > --
> > Ueimor
>
> Thanks for your help, Francois.
> I will put a few printks into the interrupt routine and hope to be able to
> tell you more tomorrow,
>
> Hans-Frieder

-- 
--
Hans-Frieder Vogt                 e-mail: hfvogt (at) arcor (dot) de

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Francois Romieu]

[-- Attachment #1: Type: text/plain, Size: 883 bytes --]

Hans-Frieder Vogt <hfvogt@arcor.de> :
[...]
[...]
> Of course x86-64 has the address-space that enables >4GB RAM, and x86-64 
> always supports DAC (as stated in include/asm-x86_64/pci.h), but I have 
> currently only 1GB RAM, so, strictly speaking, DAC is not really necessary. 

Worse than that: r8169 in 2.6.9-rc[1/2] does not advertise its ability to
DMA to high memory. 

> Strange enough, the latest Realtek driver 2.2 does not even support DAC (only 
> the lower 32 bit of the DMA-Addresses are written to the registers).
> Could it be that the Realtek driver does not support DAC for a good reason?
> 
> Anyway, I will continue searching for the problem...

Can you simply try the attached patch with the network cable unplugged ?

It will not fix your issue but if the result & 0x08 != 0, you can probably
stop your testing for now as it will mean "known issue".

--
Ueimor

[-- Attachment #2: r8169-xx0.patch --]
[-- Type: text/plain, Size: 585 bytes --]

 drivers/net/r8169.c |    3 +++
 1 files changed, 3 insertions(+)

diff -puN drivers/net/r8169.c~r8169-xx0 drivers/net/r8169.c
--- linux-2.6.9-rc1/drivers/net/r8169.c~r8169-xx0	2004-09-15 23:57:46.000000000 +0200
+++ linux-2.6.9-rc1-romieu/drivers/net/r8169.c	2004-09-16 00:59:26.000000000 +0200
@@ -1533,6 +1533,9 @@ rtl8169_hw_start(struct net_device *dev)
 	/* Enable all known interrupts by setting the interrupt mask. */
 	RTL_W16(IntrMask, rtl8169_intr_mask);
 
+	printk(KERN_INFO PFX
+		"%s: Config2 = 0x%02x\n", dev->name, RTL_R8(Config2));
+
 	netif_start_queue(dev);
 }
 

_

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Hans-Frieder Vogt]

Am Donnerstag, 16. September 2004 01:09 schrieb Francois Romieu:
> Hans-Frieder Vogt <hfvogt@arcor.de> :
> [...]
> [...]
>
> > Of course x86-64 has the address-space that enables >4GB RAM, and x86-64
> > always supports DAC (as stated in include/asm-x86_64/pci.h), but I have
> > currently only 1GB RAM, so, strictly speaking, DAC is not really
> > necessary.
>
> Worse than that: r8169 in 2.6.9-rc[1/2] does not advertise its ability to
> DMA to high memory.
>
> > Strange enough, the latest Realtek driver 2.2 does not even support DAC
> > (only the lower 32 bit of the DMA-Addresses are written to the
> > registers). Could it be that the Realtek driver does not support DAC for
> > a good reason?
> >
> > Anyway, I will continue searching for the problem...
>
> Can you simply try the attached patch with the network cable unplugged ?
>
> It will not fix your issue but if the result & 0x08 != 0, you can probably
> stop your testing for now as it will mean "known issue".
>
> --
> Ueimor

r8169: eth0: Config2 = 0x10

... does not seem to be the already known issue? Anyhow, if you have more 
ideas, I will be happy to test them :-)

Hans-Frieder

-- 
--
Hans-Frieder Vogt                 e-mail: hfvogt (at) arcor (dot) de

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Francois Romieu]

Hans-Frieder Vogt <hfvogt@arcor.de> :
[...]
> r8169: eth0: Config2 = 0x10
> 
> ... does not seem to be the already known issue? Anyhow, if you have more 

Typo of mine: it is. The BSD people have noticed some time ago that the DAC
of the chipset apparently does bad things when the card is inserted in a
32 bits wide slot. 

Jon, if your ppc64 box offers 64 bits wide PCI slots, it would be nice if
you could ttry 2.6.9-rc2-bkX, apply
http://www.fr.zoreil.com/people/francois/misc/r8169-xx0.patch
and report the content of the "Config2" line in the logs of the kernel.

--
Ueimor

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Jon Mason]

> Jon, if your ppc64 box offers 64 bits wide PCI slots, it would be nice if
> you could ttry 2.6.9-rc2-bkX, apply
> http://www.fr.zoreil.com/people/francois/misc/r8169-xx0.patch
> and report the content of the "Config2" line in the logs of the kernel.

Here is the info you requested:

r8169 Gigabit Ethernet driver 1.6LK loaded
eth8: Identified chip type is 'RTL8169s/8110s'.
eth8: RTL8169 at 0xa0000000800b7000, 00:40:f4:96:fc:3f, IRQ 131
r8169: eth8: Config2 = 0x01
r8169: eth8: link up

My p630 has 64bit PCI-X slots, but my r8169 adapter is a 32bit adapter.  See 
lspci output below (with a 64bit PCI-X e1000 adapter as a comparison).
.....
0001:61:01.1 Ethernet controller: Intel Corp. 82546GB Gigabit Ethernet 
Controller (rev 03)
        Subsystem: IBM: Unknown device 0289
        Flags: bus master, 66Mhz, medium devsel, latency 144, IRQ 122
        Memory at cc100000 (64-bit, non-prefetchable) [size=cc000000]
        Memory at cc040000 (64-bit, non-prefetchable) [size=256K]
        I/O ports at 12ec00 [size=64]
        Expansion ROM at 00040000 [disabled]
        Capabilities: [dc] Power Management version 2
        Capabilities: [e4]      Capabilities: [f0] Message Signalled 
Interrupts: 64bit+ Queue=0/0 Enable-
......
0002:01:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 
Gigabit Ethernet (rev 10)
        Subsystem: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet
        Flags: bus master, 66Mhz, medium devsel, latency 74, IRQ 131
        I/O ports at 20fc00 [size=e0000000]
        Memory at e0020000 (32-bit, non-prefetchable) [size=256]
        Expansion ROM at 00020000 [disabled]
        Capabilities: [dc] Power Management version 2


I think my AMD64 system at home has a 64bit integrated adapter, as the 
performance on it is 2.5x faster (either that or r8169 and ppc don't play 
well together).  I will verify this when I get home.

-- 
Jon Mason
jdmason@us.ibm.com

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Jon Mason]

On Thursday 16 September 2004 01:20 pm, Jon Mason wrote:
> > Jon, if your ppc64 box offers 64 bits wide PCI slots, it would be nice if
> > you could ttry 2.6.9-rc2-bkX, apply
> > http://www.fr.zoreil.com/people/francois/misc/r8169-xx0.patch
> > and report the content of the "Config2" line in the logs of the kernel.
>
> Here is the info you requested:
>
> r8169 Gigabit Ethernet driver 1.6LK loaded
> eth8: Identified chip type is 'RTL8169s/8110s'.
> eth8: RTL8169 at 0xa0000000800b7000, 00:40:f4:96:fc:3f, IRQ 131
> r8169: eth8: Config2 = 0x01
> r8169: eth8: link up
>
> My p630 has 64bit PCI-X slots, but my r8169 adapter is a 32bit adapter. 
> See lspci output below (with a 64bit PCI-X e1000 adapter as a comparison).
> .....
> 0001:61:01.1 Ethernet controller: Intel Corp. 82546GB Gigabit Ethernet
> Controller (rev 03)
>         Subsystem: IBM: Unknown device 0289
>         Flags: bus master, 66Mhz, medium devsel, latency 144, IRQ 122
>         Memory at cc100000 (64-bit, non-prefetchable) [size=cc000000]
>         Memory at cc040000 (64-bit, non-prefetchable) [size=256K]
>         I/O ports at 12ec00 [size=64]
>         Expansion ROM at 00040000 [disabled]
>         Capabilities: [dc] Power Management version 2
>         Capabilities: [e4]      Capabilities: [f0] Message Signalled
> Interrupts: 64bit+ Queue=0/0 Enable-
> ......
> 0002:01:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169
> Gigabit Ethernet (rev 10)
>         Subsystem: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit
> Ethernet Flags: bus master, 66Mhz, medium devsel, latency 74, IRQ 131 I/O
> ports at 20fc00 [size=e0000000]
>         Memory at e0020000 (32-bit, non-prefetchable) [size=256]
>         Expansion ROM at 00020000 [disabled]
>         Capabilities: [dc] Power Management version 2
>
>
> I think my AMD64 system at home has a 64bit integrated adapter, as the
> performance on it is 2.5x faster (either that or r8169 and ppc don't play
> well together).  I will verify this when I get home.

Well, it appears that my home system only has a 32bit adapter as well (see 
below).

0000:00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 
Gigabit Ethernet (rev 10)
        Subsystem: Micro-Star International Co., Ltd.: Unknown device 702c
        Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 16
        I/O ports at c800 [size=cff20000]
        Memory at cfffb700 (32-bit, non-prefetchable) [size=256]
        Expansion ROM at 00020000 [disabled]
        Capabilities: [dc] Power Management version 2

Before I make any sweeping comments about the performance on ppc64, I should 
probably do some more tests.  I'll have to get back to you regarding that.

Would you like me to run the "Config2" patch on my amd64 system?

-- 
Jon Mason
jdmason@us.ibm.com

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Francois Romieu]

Jon Mason <jdmason@us.ibm.com> :
[...]
> Before I make any sweeping comments about the performance on ppc64, I should 
> probably do some more tests.  I'll have to get back to you regarding that.
> 
> Would you like me to run the "Config2" patch on my amd64 system?

Please do. If I read you correctly, 2.6.9-rc2-bkX works (more or less)
on both your ppc64 and amd64 systems, right ?

--
Ueimor

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Andy Lutomirski]

Francois Romieu wrote:
> Jon Mason <jdmason@us.ibm.com> :
> [...]
> 
>>Before I make any sweeping comments about the performance on ppc64, I should 
>>probably do some more tests.  I'll have to get back to you regarding that.
>>
>>Would you like me to run the "Config2" patch on my amd64 system?
> 
> 
> Please do. If I read you correctly, 2.6.9-rc2-bkX works (more or less)
> on both your ppc64 and amd64 systems, right ?

No, still broken.  But I don't see any change at all in 2.6.9-rc2-bk5. 
This is on amd64, with 32-bit slots (I think).

BTW, the crash is not immediate.  It takes several seconds after trying 
to send/recieve.

I say _trying_ because I can't ping anything.  I haven't had time before 
the crash to figure out what's wrong, but the device at the other end 
does flash that a packet came through the wire.

FWIW, it looks like init_board is setting PCIDAC in tp->cp_cmd but that 
isn't updated to the card until after the rx ring is filled in 
r8169_open.  This seems suspicious, since DMA memory is being allocated 
possibly in >32-bit addresses but the card hasn't been told to support 
that.  Fixing this doesn't seem to help, though...

Turning off high DMA fixes it.  Maybe it just needs to be disabled until 
someone figures out what's going on.

--Andy

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Francois Romieu]

Andy Lutomirski <luto@myrealbox.com> :
[...]
> FWIW, it looks like init_board is setting PCIDAC in tp->cp_cmd but that 
> isn't updated to the card until after the rx ring is filled in 
> r8169_open.  This seems suspicious, since DMA memory is being allocated 
> possibly in >32-bit addresses but the card hasn't been told to support 
> that.  Fixing this doesn't seem to help, though...

rtl8169_hw_start() writes the CPlusCmd register before the ring descriptor
adresses are set. Can you elaborate why it would not be enough ?

Btw the r8169 driver in 2.6.9-rcX does not advertise NETIF_F_HIGHDMA: where
would a >32 bit address come from ?

> Turning off high DMA fixes it.  Maybe it just needs to be disabled until 
> someone figures out what's going on.

I am cooking a patch for it (+ check for PCI error).

As a side note, the r8169 chipset does not like DAC to be enabled on a
32bit system. I got the usual PCI error reported while trying it.

--
Ueimor

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Andy Lutomirski]

[-- Attachment #1: Type: text/plain, Size: 2521 bytes --]

Francois Romieu wrote:
> Andy Lutomirski <luto@myrealbox.com> :
> [...]
> 
>>FWIW, it looks like init_board is setting PCIDAC in tp->cp_cmd but that 
>>isn't updated to the card until after the rx ring is filled in 
>>r8169_open.  This seems suspicious, since DMA memory is being allocated 
>>possibly in >32-bit addresses but the card hasn't been told to support 
>>that.  Fixing this doesn't seem to help, though...
> 
> 
> rtl8169_hw_start() writes the CPlusCmd register before the ring descriptor
> adresses are set. Can you elaborate why it would not be enough ?

Because rtl8169_init_ring() is called before rtl8169_hw_start() in 
rtl8169_open().  init_ring allocates the recieve buffers, and I'm 
assuming that r8169_alloc_rx_skb() can get >32 bits.

> 
> Btw the r8169 driver in 2.6.9-rcX does not advertise NETIF_F_HIGHDMA: where
> would a >32 bit address come from ?

I was looking at 2.6.9-rc2-mm1, which has (pardon hideous line wrapping):

	if ((sizeof(dma_addr_t) > 4) && !pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
		tp->cp_cmd |= PCIDAC;
		dev->features |= NETIF_F_HIGHDMA;
                                  ^^^^^^^^^^^^^^^
	} else {
		rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
		if (rc < 0) {
			printk(KERN_ERR PFX "DMA configuration failed.\n");
			goto err_out_free_res;
		}
	}

But I have 512MB RAM, so this probably isn't a problem for me.  I'm 
running x86_64, BTW.

> 
> 
>>Turning off high DMA fixes it.  Maybe it just needs to be disabled until 
>>someone figures out what's going on.
> 
> 
> I am cooking a patch for it (+ check for PCI error).
> 
> As a side note, the r8169 chipset does not like DAC to be enabled on a
> 32bit system. I got the usual PCI error reported while trying it.

Will this be ready for 2.6.9?  Otherwise it would probably be better to 
just disable DAC so the driver keeps working.

On an unrelated note, I just took a look at the PHY timer code.  It 
looks like the PHY timer will never reactivate once it shuts off, which 
means that the resetting is completely deterministic and the printk 
conveys no useful information.  Can we just delete it (patch attached -- 
this computer mangles them)?

What does it do, anyway?  If it is necessary for someone's card (not 
mine) to acquire a gigabit link (which is what it seemed to do in old 
versions of the driver), then we're _still_ broken for the case where 
they drop the link and try to reacquire it.  Would it make sense to 
remove the reset_enable stuff in -mm for awhile and see if anyone complains?


--Andy

[-- Attachment #2: r8169-quiet.txt --]
[-- Type: text/plain, Size: 456 bytes --]

Index: 2.6.9-rc2-mm1/drivers/net/r8169.c
===================================================================
--- 2.6.9-rc2-mm1.orig/drivers/net/r8169.c	2004-09-19 16:43:09.725537944 -0700
+++ 2.6.9-rc2-mm1/drivers/net/r8169.c	2004-09-19 16:50:33.900013160 -0700
@@ -1044,8 +1044,6 @@
 	if (tp->link_ok(ioaddr))
 		goto out_unlock;
 
-	printk(KERN_WARNING PFX "%s: PHY reset until link up\n", dev->name);
-
 	tp->phy_reset_enable(ioaddr);
 
 out_mod_timer:

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Jeff Garzik]

Francois Romieu wrote:
> rtl8169_hw_start() writes the CPlusCmd register before the ring descriptor
> adresses are set. Can you elaborate why it would not be enough ?


That sounds like a bug right there...  need all the addresses set up 
before we turn on stuff.

	Jeff

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Francois Romieu]

Jeff Garzik <jgarzik@pobox.com> :
[...]
> That sounds like a bug right there...  need all the addresses set up 
> before we turn on stuff.

The description of the CPlusCmd in the 8169 datasheet includes a small note
which suggests that this register should be set up early.

It does not cost much to try and see if it makes a difference for DAC though.

--
Ueimor

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Jeff Garzik]

Francois Romieu wrote:
> Jeff Garzik <jgarzik@pobox.com> :
> [...]
> 
>>That sounds like a bug right there...  need all the addresses set up 
>>before we turn on stuff.
> 
> 
> The description of the CPlusCmd in the 8169 datasheet includes a small note
> which suggests that this register should be set up early.
> 
> It does not cost much to try and see if it makes a difference for DAC though.

Let me know what happens :)

	Jeff

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Francois Romieu]

Jeff Garzik <jgarzik@pobox.com> :
[...]
> Let me know what happens :)

Nothing conclusive so far.

I applied patch below on my 32bit system on top of current 2.6.9-rc2-mm1 + 
patch issued yesterday + extra hack to force PCI DAC on 32 bit system.
It does not help if I force PCI DAC.
It does not change anything if PCI DAC is not enabled.


diff -puN drivers/net/r8169.c~r8169-145b-4 drivers/net/r8169.c
--- linux-2.6.9-rc2/drivers/net/r8169.c~r8169-145b-4	2004-09-20 21:39:20.000000000 +0200
+++ linux-2.6.9-rc2-fr/drivers/net/r8169.c	2004-09-20 21:39:20.000000000 +0200
@@ -1483,6 +1483,11 @@ rtl8169_hw_start(struct net_device *dev)
 	void *ioaddr = tp->mmio_addr;
 	u32 i;
 
+	RTL_W32(TxDescStartAddrLow, ((u64) tp->TxPhyAddr & DMA_32BIT_MASK));
+	RTL_W32(TxDescStartAddrHigh, ((u64) tp->TxPhyAddr >> 32));
+	RTL_W32(RxDescAddrLow, ((u64) tp->RxPhyAddr & DMA_32BIT_MASK));
+	RTL_W32(RxDescAddrHigh, ((u64) tp->RxPhyAddr >> 32));
+
 	/* Soft reset the chip. */
 	RTL_W8(ChipCmd, CmdReset);
 
@@ -1494,7 +1499,6 @@ rtl8169_hw_start(struct net_device *dev)
 	}
 
 	RTL_W8(Cfg9346, Cfg9346_Unlock);
-	RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb);
 	RTL_W8(EarlyTxThres, EarlyTxThld);
 
 	// For gigabit rtl8169
@@ -1509,24 +1513,9 @@ rtl8169_hw_start(struct net_device *dev)
 	RTL_W32(TxConfig,
 		(TX_DMA_BURST << TxDMAShift) | (InterFrameGap <<
 						TxInterFrameGapShift));
-	tp->cp_cmd |= RTL_R16(CPlusCmd);
-	RTL_W16(CPlusCmd, tp->cp_cmd);
-
-	if (tp->mac_version == RTL_GIGA_MAC_VER_D) {
-		dprintk(KERN_INFO PFX "Set MAC Reg C+CR Offset 0xE0. "
-			"Bit-3 and bit-14 MUST be 1\n");
-		tp->cp_cmd |= (1 << 14) | PCIMulRW;
-		RTL_W16(CPlusCmd, tp->cp_cmd);
-	}
-
 	tp->cur_rx = 0;
 
-	RTL_W32(TxDescStartAddrLow, ((u64) tp->TxPhyAddr & DMA_32BIT_MASK));
-	RTL_W32(TxDescStartAddrHigh, ((u64) tp->TxPhyAddr >> 32));
-	RTL_W32(RxDescAddrLow, ((u64) tp->RxPhyAddr & DMA_32BIT_MASK));
-	RTL_W32(RxDescAddrHigh, ((u64) tp->RxPhyAddr >> 32));
 	RTL_W8(Cfg9346, Cfg9346_Lock);
-	udelay(10);
 
 	RTL_W32(RxMissed, 0);
 
@@ -1538,6 +1527,17 @@ rtl8169_hw_start(struct net_device *dev)
 	/* Enable all known interrupts by setting the interrupt mask. */
 	RTL_W16(IntrMask, rtl8169_intr_mask);
 
+	tp->cp_cmd |= RTL_R16(CPlusCmd);
+
+	if (tp->mac_version == RTL_GIGA_MAC_VER_D) {
+		dprintk(KERN_INFO PFX "Set MAC Reg C+CR Offset 0xE0. "
+			"Bit-3 and bit-14 MUST be 1\n");
+		tp->cp_cmd |= (1 << 14) | PCIMulRW;
+	}
+
+	RTL_W16(CPlusCmd, tp->cp_cmd);
+	RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb);
+
 	netif_start_queue(dev);
 }
 

_

Re: 2.6.9-rc1-bk11+ and 2.6.9-rc1-mm3,4 r8169: freeze during boot (FIX included)

[Jon Mason]

Andy,
Your setup sounds very similar to mine, and I am not hitting the error.  I am 
running Gentoo on AMD Athlon(tm) 64 Processor 3200+ with 512MB RAM.  My r8169 
adapter (8110 chipset) is integrated in my MoBo.  How is your setup 
different?

Thanks,

-- 
Jon Mason
jdmason@us.ibm.com