From: Philip Craig <philipc@snapgear.com>
To: Jeff Garzik <jgarzik@pobox.com>
Cc: netdev@vger.kernel.org
Subject: [PATCH 2/2] 8139cp: add ethtool eeprom support
Date: Wed, 14 Jun 2006 16:43:08 +1000 [thread overview]
Message-ID: <448FAFFC.7070006@snapgear.com> (raw)
Implement the ethtool eeprom operations for the 8139cp driver.
Tested on x86 and big-endian ARM.
Signed-off-by: Philip Craig <philipc@snapgear.com>
Index: linux-2.6.17-rc6/drivers/net/8139cp.c
===================================================================
--- linux-2.6.17-rc6.orig/drivers/net/8139cp.c 2006-06-14 15:59:26.000000000 +1000
+++ linux-2.6.17-rc6/drivers/net/8139cp.c 2006-06-14 15:59:53.000000000 +1000
@@ -401,6 +401,11 @@ static void cp_clean_rings (struct cp_pr
#ifdef CONFIG_NET_POLL_CONTROLLER
static void cp_poll_controller(struct net_device *dev);
#endif
+static int cp_get_eeprom_len(struct net_device *dev);
+static int cp_get_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *data);
+static int cp_set_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *data);
static struct pci_device_id cp_pci_tbl[] = {
{ PCI_VENDOR_ID_REALTEK, PCI_DEVICE_ID_REALTEK_8139,
@@ -1577,6 +1582,9 @@ static struct ethtool_ops cp_ethtool_ops
.get_strings = cp_get_strings,
.get_ethtool_stats = cp_get_ethtool_stats,
.get_perm_addr = ethtool_op_get_perm_addr,
+ .get_eeprom_len = cp_get_eeprom_len,
+ .get_eeprom = cp_get_eeprom,
+ .set_eeprom = cp_set_eeprom,
};
static int cp_ioctl (struct net_device *dev, struct ifreq *rq, int cmd)
@@ -1612,24 +1620,32 @@ static int cp_ioctl (struct net_device *
#define eeprom_delay() readl(ee_addr)
/* The EEPROM commands include the alway-set leading bit. */
+#define EE_EXTEND_CMD (4)
#define EE_WRITE_CMD (5)
#define EE_READ_CMD (6)
#define EE_ERASE_CMD (7)
-static int read_eeprom (void __iomem *ioaddr, int location, int addr_len)
-{
- int i;
- unsigned retval = 0;
- void __iomem *ee_addr = ioaddr + Cfg9346;
- int read_cmd = location | (EE_READ_CMD << addr_len);
+#define EE_EWDS_ADDR (0)
+#define EE_WRAL_ADDR (1)
+#define EE_ERAL_ADDR (2)
+#define EE_EWEN_ADDR (3)
+
+#define CP_EEPROM_MAGIC PCI_DEVICE_ID_REALTEK_8139
+static void eeprom_cmd_start(void __iomem *ee_addr)
+{
writeb (EE_ENB & ~EE_CS, ee_addr);
writeb (EE_ENB, ee_addr);
eeprom_delay ();
+}
+
+static void eeprom_cmd(void __iomem *ee_addr, int cmd, int cmd_len)
+{
+ int i;
- /* Shift the read command bits out. */
- for (i = 3 + addr_len - 1; i >= 0; i--) {
- int dataval = (read_cmd & (1 << i)) ? EE_DATA_WRITE : 0;
+ /* Shift the command bits out. */
+ for (i = cmd_len - 1; i >= 0; i--) {
+ int dataval = (cmd & (1 << i)) ? EE_DATA_WRITE : 0;
writeb (EE_ENB | dataval, ee_addr);
eeprom_delay ();
writeb (EE_ENB | dataval | EE_SHIFT_CLK, ee_addr);
@@ -1637,6 +1653,33 @@ static int read_eeprom (void __iomem *io
}
writeb (EE_ENB, ee_addr);
eeprom_delay ();
+}
+
+static void eeprom_cmd_end(void __iomem *ee_addr)
+{
+ writeb (~EE_CS, ee_addr);
+ eeprom_delay ();
+}
+
+static void eeprom_extend_cmd(void __iomem *ee_addr, int extend_cmd,
+ int addr_len)
+{
+ int cmd = (EE_EXTEND_CMD << addr_len) | (extend_cmd << (addr_len - 2));
+
+ eeprom_cmd_start(ee_addr);
+ eeprom_cmd(ee_addr, cmd, 3 + addr_len);
+ eeprom_cmd_end(ee_addr);
+}
+
+static u16 read_eeprom (void __iomem *ioaddr, int location, int addr_len)
+{
+ int i;
+ u16 retval = 0;
+ void __iomem *ee_addr = ioaddr + Cfg9346;
+ int read_cmd = location | (EE_READ_CMD << addr_len);
+
+ eeprom_cmd_start(ee_addr);
+ eeprom_cmd(ee_addr, read_cmd, 3 + addr_len);
for (i = 16; i > 0; i--) {
writeb (EE_ENB | EE_SHIFT_CLK, ee_addr);
@@ -1648,13 +1691,125 @@ static int read_eeprom (void __iomem *io
eeprom_delay ();
}
- /* Terminate the EEPROM access. */
- writeb (~EE_CS, ee_addr);
- eeprom_delay ();
+ eeprom_cmd_end(ee_addr);
return retval;
}
+static void write_eeprom(void __iomem *ioaddr, int location, u16 val,
+ int addr_len)
+{
+ int i;
+ void __iomem *ee_addr = ioaddr + Cfg9346;
+ int write_cmd = location | (EE_WRITE_CMD << addr_len);
+
+ eeprom_extend_cmd(ee_addr, EE_EWEN_ADDR, addr_len);
+
+ eeprom_cmd_start(ee_addr);
+ eeprom_cmd(ee_addr, write_cmd, 3 + addr_len);
+ eeprom_cmd(ee_addr, val, 16);
+ eeprom_cmd_end(ee_addr);
+
+ eeprom_cmd_start(ee_addr);
+ for (i = 0; i < 20000; i++)
+ if (readb(ee_addr) & EE_DATA_READ)
+ break;
+ eeprom_cmd_end(ee_addr);
+
+ eeprom_extend_cmd(ee_addr, EE_EWDS_ADDR, addr_len);
+}
+
+static int cp_get_eeprom_len(struct net_device *dev)
+{
+ struct cp_private *cp = netdev_priv(dev);
+ int size;
+
+ spin_lock_irq(&cp->lock);
+ size = read_eeprom(cp->regs, 0, 8) == 0x8129 ? 256 : 128;
+ spin_unlock_irq(&cp->lock);
+
+ return size;
+}
+
+static int cp_get_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *data)
+{
+ struct cp_private *cp = netdev_priv(dev);
+ unsigned int addr_len;
+ u16 val;
+ u32 offset = eeprom->offset >> 1;
+ u32 len = eeprom->len;
+ u32 i = 0;
+
+ eeprom->magic = CP_EEPROM_MAGIC;
+
+ spin_lock_irq(&cp->lock);
+
+ addr_len = read_eeprom(cp->regs, 0, 8) == 0x8129 ? 8 : 6;
+
+ if (eeprom->offset & 1) {
+ val = read_eeprom(cp->regs, offset, addr_len);
+ data[i++] = (u8)(val >> 8);
+ offset++;
+ }
+
+ while (i < len - 1) {
+ val = read_eeprom(cp->regs, offset, addr_len);
+ data[i++] = (u8)val;
+ data[i++] = (u8)(val >> 8);
+ offset++;
+ }
+
+ if (i < len) {
+ val = read_eeprom(cp->regs, offset, addr_len);
+ data[i] = (u8)val;
+ }
+
+ spin_unlock_irq(&cp->lock);
+ return 0;
+}
+
+static int cp_set_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *eeprom, u8 *data)
+{
+ struct cp_private *cp = netdev_priv(dev);
+ unsigned int addr_len;
+ u16 val;
+ u32 offset = eeprom->offset >> 1;
+ u32 len = eeprom->len;
+ u32 i = 0;
+
+ if (eeprom->magic != CP_EEPROM_MAGIC)
+ return -EINVAL;
+
+ spin_lock_irq(&cp->lock);
+
+ addr_len = read_eeprom(cp->regs, 0, 8) == 0x8129 ? 8 : 6;
+
+ if (eeprom->offset & 1) {
+ val = read_eeprom(cp->regs, offset, addr_len) & 0xff;
+ val |= (u16)data[i++] << 8;
+ write_eeprom(cp->regs, offset, val, addr_len);
+ offset++;
+ }
+
+ while (i < len - 1) {
+ val = (u16)data[i++];
+ val |= (u16)data[i++] << 8;
+ write_eeprom(cp->regs, offset, val, addr_len);
+ offset++;
+ }
+
+ if (i < len) {
+ val = read_eeprom(cp->regs, offset, addr_len) & 0xff00;
+ val |= (u16)data[i];
+ write_eeprom(cp->regs, offset, val, addr_len);
+ }
+
+ spin_unlock_irq(&cp->lock);
+ return 0;
+}
+
/* Put the board into D3cold state and wait for WakeUp signal */
static void cp_set_d3_state (struct cp_private *cp)
{
reply other threads:[~2006-06-14 6:43 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=448FAFFC.7070006@snapgear.com \
--to=philipc@snapgear.com \
--cc=jgarzik@pobox.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).