From: Sergej Bauer <sbauer@blackbox.su>
To: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>,
netdev@vger.kernel.org, "David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Bryan Whitehead <bryan.whitehead@microchip.com>,
UNGLinuxDriver@microchip.com,
Simon Horman <simon.horman@netronome.com>,
Mark Einon <mark.einon@gmail.com>,
Madalin Bucur <madalin.bucur@oss.nxp.com>,
Arnd Bergmann <arnd@arndb.de>,
Masahiro Yamada <masahiroy@kernel.org>,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2] lan743x: add virtual PHY for PHY-less devices
Date: Mon, 25 Jan 2021 11:57:47 +0300 [thread overview]
Message-ID: <4533953.k7tWhSxINc@metabook> (raw)
In-Reply-To: <YAt8trmR1FjGnCeF@lunn.ch>
On Saturday, January 23, 2021 4:32:38 AM MSK Andrew Lunn wrote:
> > it migth be helpful for developers work on userspace networking tools with
> > PHY-less lan743x
>
> (the interface even could not be brought up)
>
> > of course, there nothing much to do without TP port but the difference is
> > representative.
> >
> > sbauer@metamini ~$ sudo ethtool eth7
> > Settings for eth7:
> > Cannot get device settings: No such device
> >
> > Supports Wake-on: pumbag
> > Wake-on: d
> > Current message level: 0x00000137 (311)
> >
> > drv probe link ifdown ifup tx_queued
> >
> > Link detected: no
> >
> > sbauer@metamini ~$ sudo ifup eth7
> > sbauer@metamini ~$ sudo ethtool eth7
> >
> > Settings for eth7:
> > Supported ports: [ MII ]
> > Supported link modes: 10baseT/Full
> >
> > 100baseT/Full
> > 1000baseT/Full
> >
> > Supported pause frame use: Symmetric Receive-only
> > Supports auto-negotiation: Yes
> > Supported FEC modes: Not reported
> > Advertised link modes: 10baseT/Full
> >
> > 100baseT/Full
> > 1000baseT/Full
> >
> > Advertised pause frame use: Symmetric Receive-only
> > Advertised auto-negotiation: Yes
> > Advertised FEC modes: Not reported
> > Speed: 1000Mb/s
> > Duplex: Full
> > Port: MII
> > PHYAD: 0
> > Transceiver: internal
> > Auto-negotiation: on
> > Supports Wake-on: pumbag
> > Wake-on: d
> > Current message level: 0x00000137 (311)
> >
> > drv probe link ifdown ifup tx_queued
> >
> > Link detected: yes
> >
> > sbauer@metamini ~$ sudo mii-tool -vv eth7
> > Using SIOCGMIIPHY=0x8947
> > eth7: negotiated 1000baseT-FD, link ok
> >
> > registers for MII PHY 0:
> > 5140 512d 7431 0011 4140 4140 000d 0000
> > 0000 0200 7800 0000 0000 0000 0000 2000
> > 0000 0000 0000 0000 0000 0000 0000 0000
> > 0000 0000 0000 0000 0000 0000 0000 0000
> >
> > product info: vendor 1d:0c:40, model 1 rev 1
> > basic mode: loopback, autonegotiation enabled
> > basic status: autonegotiation complete, link ok
> > capabilities: 1000baseT-FD 100baseTx-FD 10baseT-FD
> > advertising: 1000baseT-FD 100baseTx-FD 10baseT-FD
> > link partner: 1000baseT-FD 100baseTx-FD 10baseT-FD
>
> You have not shown anything i cannot do with the ethernet interfaces i
> have in my laptop. And since ethtool is pretty standardized, what
> lan743x offers should be pretty much the same as any 1G Ethernet MAC
> using most 1G PHYs.
>
> Andrew
Andrew, for this moment with lan743x we can get only this:
sbauer@metamini ~/devel/kernel-works/net-next.git master$ sudo ethtool eth7
Settings for eth7:
Cannot get device settings: No such device
Supports Wake-on: pumbag
Wake-on: d
Current message level: 0x00000137 (311)
drv probe link ifdown ifup tx_queued
Link detected: no
sbauer@metamini ~/devel/kernel-works/net-next.git master$ sudo mii-tool -vv
eth7
Using SIOCGMIIPHY=0x8947
SIOCGMIIPHY on 'eth7' failed: Invalid argument
--
Regards,
Sergej.
next prev parent reply other threads:[~2021-01-26 21:28 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-22 21:42 [PATCH v2] lan743x: add virtual PHY for PHY-less devices Sergej Bauer
2021-01-22 21:52 ` Florian Fainelli
2021-01-22 22:11 ` Sergej Bauer
2021-01-22 22:08 ` Andrew Lunn
2021-01-22 23:09 ` Sergej Bauer
2021-01-22 23:23 ` Andrew Lunn
2021-01-22 23:58 ` Sergej Bauer
2021-01-23 0:01 ` Florian Fainelli
2021-01-23 1:01 ` Sergej Bauer
2021-01-23 1:32 ` Andrew Lunn
2021-01-23 4:01 ` Sergej Bauer
2021-01-25 8:57 ` Sergej Bauer [this message]
2021-01-23 1:39 ` Florian Fainelli
2021-01-25 8:57 ` Sergej Bauer
2021-01-25 10:23 ` Sergej Bauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4533953.k7tWhSxINc@metabook \
--to=sbauer@blackbox.su \
--cc=UNGLinuxDriver@microchip.com \
--cc=andrew@lunn.ch \
--cc=arnd@arndb.de \
--cc=bryan.whitehead@microchip.com \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=madalin.bucur@oss.nxp.com \
--cc=mark.einon@gmail.com \
--cc=masahiroy@kernel.org \
--cc=netdev@vger.kernel.org \
--cc=simon.horman@netronome.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).