[PATCH] 2.6 driver for Silan SC92031

[PATCH] 2.6 driver for Silan SC92031

[Cesar Eduardo Barros]

From: Cesar Eduardo Barros <cesarb@cesarb.net>

This is a driver for the Silan SC92031/Rsltek 8139D NIC chip. It's a
rewrite of the vendor 2.4 driver for 2.6, and has been lightly tested
on a 2.6.17 x86-64 kernel with the Ubuntu patches (as a out-of-tree
module only).

This chip is found on at least one counterfeit Encore ENL832-TX-RENT
NIC [1], which came with a mini-CD with the 2.4 driver. A slightly
older version of the driver was found at [2]. The main difference
between them is that the newer one has a small bugfix in the RX path,
a lot of gratuitous renaming of functions, all the printable strings
changed to show as a "Rsltek 8139D" [sic], and a PCI ID of 8139 instead
of 2031.

This patch has been modified to apply cleanly on 2.6.19; to run on
2.6.17, just add back the struct pt_regs* argument to the interrupt
handler and to its call at poll_controller(). It compiles on 2.6.19 for
x86-64 as a module.

[1] See http://www.encore-usa.com/faq.php under ENL832-TX-RENT for more
    information
[2] Look for SL_LINUX.ZIP (which is really a .tar.gz) at
    http://broadbandforum.in/dataone_Intex_LAN_cardlinux-t4207-s15.html

Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>

---

That said, I'm mostly sending this to get comments on any mistakes I
might have made (I have this nagging feeling I must have made at least
one), and most importantly to make it available for adventurous folks
who are stuck with boards with that chip; I do not expect it to be
considered ready for inclusion yet, and it also needs more testing.

diff -uprN -X linux-2.6.19/Documentation/dontdiff linux-2.6.19.orig/drivers/net/Kconfig linux-2.6.19/drivers/net/Kconfig
--- linux-2.6.19.orig/drivers/net/Kconfig	2006-11-29 19:57:37.000000000 -0200
+++ linux-2.6.19/drivers/net/Kconfig	2006-12-02 18:50:23.000000000 -0200
@@ -1777,6 +1777,18 @@ config LAN_SAA9730
 	  workstations.
 	  See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>.

+config SC92031
+	tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
+	depends on NET_PCI && PCI && EXPERIMENTAL
+	select CRC32
+	---help---
+	  This is a driver for the Fast Ethernet PCI network cards based on
+	  the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
+	  have one of these, say Y here.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called sc92031.  This is recommended.
+
 config NET_POCKET
 	bool "Pocket and portable adapters"
 	depends on NET_ETHERNET && PARPORT
diff -uprN -X linux-2.6.19/Documentation/dontdiff linux-2.6.19.orig/drivers/net/Makefile linux-2.6.19/drivers/net/Makefile
--- linux-2.6.19.orig/drivers/net/Makefile	2006-11-29 19:57:37.000000000 -0200
+++ linux-2.6.19/drivers/net/Makefile	2006-12-02 18:50:23.000000000 -0200
@@ -160,6 +160,7 @@ obj-$(CONFIG_APRICOT) += 82596.o
 obj-$(CONFIG_LASI_82596) += lasi_82596.o
 obj-$(CONFIG_MVME16x_NET) += 82596.o
 obj-$(CONFIG_BVME6000_NET) += 82596.o
+obj-$(CONFIG_SC92031) += sc92031.o

 # This is also a 82596 and should probably be merged
 obj-$(CONFIG_LP486E) += lp486e.o
diff -uprN -X linux-2.6.19/Documentation/dontdiff linux-2.6.19.orig/drivers/net/sc92031.c linux-2.6.19/drivers/net/sc92031.c
--- linux-2.6.19.orig/drivers/net/sc92031.c	1969-12-31 21:00:00.000000000 -0300
+++ linux-2.6.19/drivers/net/sc92031.c	2006-12-02 19:41:17.000000000 -0200
@@ -0,0 +1,1617 @@
+/*  Silan SC92031 PCI Fast Ethernet Adapter driver
+ *
+ *  Based on vendor drivers:
+ *  Silan Fast Ethernet Netcard Driver:
+ *    MODULE_AUTHOR ("gaoyonghong");
+ *    MODULE_DESCRIPTION ("SILAN Fast Ethernet driver");
+ *    MODULE_LICENSE("GPL");
+ *  8139D Fast Ethernet driver:
+ *    (C) 2002 by gaoyonghong
+ *    MODULE_AUTHOR ("gaoyonghong");
+ *    MODULE_DESCRIPTION ("Rsltek 8139D PCI Fast Ethernet Adapter driver");
+ *    MODULE_LICENSE("GPL");
+ *  Both are almost identical and seem to be based on pci-skeleton.c
+ *
+ *  Rewritten for 2.6 by Cesar Eduardo Barros
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/crc32.h>
+
+#define PCI_VENDOR_ID_SILAN		0x1904
+#define PCI_DEVICE_ID_SILAN_SC92031	0x2031
+#define PCI_DEVICE_ID_SILAN_8139D	0x8139
+
+#define SC92031_NAME "sc92031"
+#define SC92031_DESCRIPTION "Silan SC92031 PCI Fast Ethernet Adapter driver"
+#define SC92031_VERSION "2.0a"
+
+/* BAR 0 is MMIO, BAR 1 is PIO */
+#ifndef SC92031_USE_BAR
+#define SC92031_USE_BAR 1
+#endif
+
+/* Maximum number of multicast addresses to filter (vs. Rx-all-multicast). */
+static int multicast_filter_limit = 64;
+module_param(multicast_filter_limit, int, 0);
+MODULE_PARM_DESC(multicast_filter_limit,
+	"Maximum number of filtered multicast addresses");
+
+static int media;
+module_param(media, int, 0);
+MODULE_PARM_DESC(media, "Media type (0x00 = autodetect,"
+	" 0x01 = 10M half, 0x02 = 10M full,"
+	" 0x04 = 100M half, 0x08 = 100M full)");
+
+/* Size of the in-memory receive ring. */
+#define  RX_BUF_LEN_IDX  3 /* 0==8K, 1==16K, 2==32K, 3==64K ,4==128K*/
+#define  RX_BUF_LEN	(8192 << RX_BUF_LEN_IDX)
+
+/* Number of Tx descriptor registers. */
+#define  NUM_TX_DESC	   4
+
+/* max supported ethernet frame size -- must be at least (dev->mtu+14+4).*/
+#define  MAX_ETH_FRAME_SIZE	  1536
+
+/* Size of the Tx bounce buffers -- must be at least (dev->mtu+14+4). */
+#define  TX_BUF_SIZE       MAX_ETH_FRAME_SIZE
+#define  TX_BUF_TOT_LEN    (TX_BUF_SIZE * NUM_TX_DESC)
+
+/* The following settings are log_2(bytes)-4:  0 == 16 bytes .. 6==1024, 7==end of packet. */
+#define  RX_FIFO_THRESH    7     /* Rx buffer level before first PCI xfer.  */
+
+/* Time in jiffies before concluding the transmitter is hung. */
+#define  TX_TIMEOUT     (4*HZ)
+
+#define  SILAN_STATS_NUM    2    /* number of ETHTOOL_GSTATS */
+
+/* media options */
+#define  AUTOSELECT    0x00
+#define  M10_HALF      0x01
+#define  M10_FULL      0x02
+#define  M100_HALF     0x04
+#define  M100_FULL     0x08
+
+ /* Symbolic offsets to registers. */
+enum  silan_registers {
+   Config0    = 0x00,         // Config0
+   Config1    = 0x04,         // Config1
+   RxBufWPtr  = 0x08,         // Rx buffer writer poiter
+   IntrStatus = 0x0C,         // Interrupt status
+   IntrMask   = 0x10,         // Interrupt mask
+   RxbufAddr  = 0x14,         // Rx buffer start address
+   RxBufRPtr  = 0x18,         // Rx buffer read pointer
+   Txstatusall = 0x1C,        // Transmit status of all descriptors
+   TxStatus0  = 0x20,	      // Transmit status (Four 32bit registers).
+   TxAddr0    = 0x30,         // Tx descriptors (also four 32bit).
+   RxConfig   = 0x40,         // Rx configuration
+   MAC0	      = 0x44,	      // Ethernet hardware address.
+   MAR0	      = 0x4C,	      // Multicast filter.
+   RxStatus0  = 0x54,         // Rx status
+   TxConfig   = 0x5C,         // Tx configuration
+   PhyCtrl    = 0x60,         // physical control
+   FlowCtrlConfig = 0x64,     // flow control
+   Miicmd0    = 0x68,         // Mii command0 register
+   Miicmd1    = 0x6C,         // Mii command1 register
+   Miistatus  = 0x70,         // Mii status register
+   Timercnt   = 0x74,         // Timer counter register
+   TimerIntr  = 0x78,         // Timer interrupt register
+   PMConfig   = 0x7C,         // Power Manager configuration
+   CRC0       = 0x80,         // Power Manager CRC ( Two 32bit regisers)
+   Wakeup0    = 0x88,         // power Manager wakeup( Eight 64bit regiser)
+   LSBCRC0    = 0xC8,         // power Manager LSBCRC(Two 32bit regiser)
+   TestD0     = 0xD0,
+   TestD4     = 0xD4,
+   TestD8     = 0xD8,
+};
+
+#define MII_BMCR            0        // Basic mode control register
+#define MII_BMSR            1        // Basic mode status register
+#define MII_JAB             16
+#define MII_OutputStatus    24
+
+#define BMCR_FULLDPLX       0x0100    // Full duplex
+#define BMCR_ANRESTART      0x0200    // Auto negotiation restart
+#define BMCR_ANENABLE       0x1000    // Enable auto negotiation
+#define BMCR_SPEED100       0x2000    // Select 100Mbps
+#define BMSR_LSTATUS        0x0004    // Link status
+#define PHY_16_JAB_ENB      0x1000
+#define PHY_16_PORT_ENB     0x1
+
+enum IntrStatusBits {
+   LinkFail       = 0x80000000,
+   LinkOK         = 0x40000000,
+   TimeOut        = 0x20000000,
+   RxOverflow     = 0x0040,
+   RxOK           = 0x0020,
+   TxOK           = 0x0001,
+   IntrBits = LinkFail|LinkOK|TimeOut|RxOverflow|RxOK|TxOK,
+};
+
+enum TxStatusBits {
+   TxCarrierLost = 0x20000000,
+   TxAborted     = 0x10000000,
+   TxOutOfWindow = 0x08000000,
+   TxNccShift    = 22,
+   EarlyTxThresShift = 16,
+   TxStatOK      = 0x8000,
+   TxUnderrun    = 0x4000,
+   TxOwn         = 0x2000,
+};
+
+enum RxStatusBits {
+   RxStatesOK   = 0x80000,
+   RxBadAlign   = 0x40000,
+   RxHugeFrame  = 0x20000,
+   RxSmallFrame = 0x10000,
+   RxCRCOK      = 0x8000,
+   RxCrlFrame   = 0x4000,
+   Rx_Broadcast = 0x2000,
+   Rx_Multicast = 0x1000,
+   RxAddrMatch  = 0x0800,
+   MiiErr       = 0x0400,
+};
+
+enum RxConfigBits {
+   RxFullDx    = 0x80000000,
+   RxEnb       = 0x40000000,
+   RxSmall     = 0x20000000,
+   RxHuge      = 0x10000000,
+   RxErr       = 0x08000000,
+   RxAllphys   = 0x04000000,
+   RxMulticast = 0x02000000,
+   RxBroadcast = 0x01000000,
+   RxLoopBack  = (1 << 23) | (1 << 22),
+   LowThresholdShift  = 12,
+   HighThresholdShift = 2,
+};
+
+enum TxConfigBits {
+   TxFullDx       = 0x80000000,
+   TxEnb          = 0x40000000,
+   TxEnbPad       = 0x20000000,
+   TxEnbHuge      = 0x10000000,
+   TxEnbFCS       = 0x08000000,
+   TxNoBackOff    = 0x04000000,
+   TxEnbPrem      = 0x02000000,
+   TxCareLostCrs  = 0x1000000,
+   TxExdCollNum   = 0xf00000,
+   TxDataRate     = 0x80000,
+};
+
+enum PhyCtrlconfigbits {
+   PhyCtrlAne         = 0x80000000,
+   PhyCtrlSpd100      = 0x40000000,
+   PhyCtrlSpd10       = 0x20000000,
+   PhyCtrlPhyBaseAddr = 0x1f000000,
+   PhyCtrlDux         = 0x800000,
+   PhyCtrlReset       = 0x400000,
+};
+
+enum FlowCtrlConfigBits {
+   FlowCtrlFullDX = 0x80000000,
+   FlowCtrlEnb    = 0x40000000,
+};
+
+enum Config0Bits {
+   Cfg0_Reset  = 0x80000000,
+   Cfg0_Anaoff = 0x40000000,
+   Cfg0_LDPS   = 0x20000000,
+};
+
+enum Config1Bits {
+   Cfg1_EarlyRx = 1 << 31,
+   Cfg1_EarlyTx = 1 << 30,
+
+   //rx buffer size
+   Cfg1_Rcv8K   = 0x0,
+   Cfg1_Rcv16K  = 0x1,
+   Cfg1_Rcv32K  = 0x3,
+   Cfg1_Rcv64K  = 0x7,
+   Cfg1_Rcv128K = 0xf,
+};
+
+enum MiiCmd0Bits {
+   Mii_Divider = 0x20000000,
+   Mii_WRITE   = 0x400000,
+   Mii_READ    = 0x200000,
+   Mii_SCAN    = 0x100000,
+   Mii_Tamod   = 0x80000,
+   Mii_Drvmod  = 0x40000,
+   Mii_mdc     = 0x20000,
+   Mii_mdoen   = 0x10000,
+   Mii_mdo     = 0x8000,
+   Mii_mdi     = 0x4000,
+};
+
+enum MiiStatusBits {
+    Mii_StatusBusy = 0x80000000,
+};
+
+enum PMConfigBits {
+   PM_Enable  = 1 << 31,
+   PM_LongWF  = 1 << 30,
+   PM_Magic   = 1 << 29,
+   PM_LANWake = 1 << 28,
+   PM_LWPTN   = (1 << 27 | 1<< 26),
+   PM_LinkUp  = 1 << 25,
+   PM_WakeUp  = 1 << 24,
+};
+
+/* tx ring entry */
+struct sc92031_tx_info {
+	void		*bounce_buffer;
+	dma_addr_t	bounce_buffer_dma_addr;
+};
+
+/* Locking rules:
+ * priv->lock protects most of the fields of priv and most of the
+ * hardware registers. It does not have to protect against softirqs
+ * between sc92031_disable_interrupts and sc92031_enable_interrupts;
+ * it also does not need to be used in ->open and ->stop while the
+ * device interrupts are off.
+ * Not having to protect against softirqs is very useful due to heavy
+ * use of mdelay() at _sc92031_reset.
+ * Functions prefixed with _sc92031_ must be called with the lock held;
+ * functions prefixed with sc92031_ must be called without the lock held.
+ * Use mmiowb() before unlocking if the hardware was written to.
+ */
+
+struct sc92031_priv {
+	spinlock_t		lock;
+	/* iomap.h cookie */
+	void __iomem		*port_base;
+	/* pci device structure */
+	struct pci_dev		*pdev;
+	/* tasklet */
+	struct tasklet_struct	tasklet;
+
+	/* CPU address of rx ring */
+	void			*rx_ring;
+	/* PCI address of rx ring */
+	dma_addr_t		rx_ring_dma_addr;
+	/* PCI address of rx ring read pointer */
+	dma_addr_t		rx_ring_tail;
+
+	/* tx ring write index */
+	unsigned		tx_head;
+	/* tx ring read index */
+	unsigned		tx_tail;
+	/* tx ring */
+	struct sc92031_tx_info	tx_info[NUM_TX_DESC];
+
+	/* copies of some hardware registers */
+	u32			intr_status;
+	u32			rx_config;
+	u32			tx_config;
+	u32			pm_config;
+
+	/* copy of some flags from dev->flags */
+	unsigned int		mc_flags;
+
+	/* for ETHTOOL_GSTATS */
+	u64			tx_timeouts;
+	u64			rx_loss;
+
+	/* for dev->get_stats */
+	long			rx_value;
+	struct net_device_stats	stats;
+};
+
+static u32 _sc92031_mii_wait(void __iomem *port_base)
+{
+	u32 mii_status;
+
+	do {
+		udelay(10);
+		mii_status = ioread32(port_base + Miistatus);
+	} while (mii_status & Mii_StatusBusy);
+
+	return mii_status;
+}
+
+static u32 _sc92031_mii_cmd(void __iomem *port_base, u32 cmd0, u32 cmd1)
+{
+	iowrite32(Mii_Divider, port_base + Miicmd0);
+
+	_sc92031_mii_wait(port_base);
+
+	iowrite32(cmd1, port_base + Miicmd1);
+	iowrite32(Mii_Divider | cmd0, port_base + Miicmd0);
+
+	return _sc92031_mii_wait(port_base);
+}
+
+static void _sc92031_mii_scan(void __iomem *port_base)
+{
+	_sc92031_mii_cmd(port_base, Mii_SCAN, 0x1 << 6);
+}
+
+static u16 _sc92031_mii_read(void __iomem *port_base, unsigned reg)
+{
+	return _sc92031_mii_cmd(port_base, Mii_READ, reg << 6) >> 13;
+}
+
+static void _sc92031_mii_write(void __iomem *port_base, unsigned reg, u16 val)
+{
+	_sc92031_mii_cmd(port_base, Mii_WRITE, (reg << 6) | ((u32)val << 11));
+}
+
+static void sc92031_disable_interrupts(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+
+	tasklet_disable(&priv->tasklet);
+
+	iowrite32(0, port_base + IntrMask);
+	mmiowb();
+}
+
+static void sc92031_enable_interrupts(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+
+	tasklet_enable(&priv->tasklet);
+
+	iowrite32(IntrBits, port_base + IntrMask);
+	mmiowb();
+}
+
+static void _sc92031_disable_tx_rx(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+
+	priv->rx_config &= ~RxEnb;
+	priv->tx_config &= ~TxEnb;
+	iowrite32(priv->rx_config, port_base + RxConfig);
+	iowrite32(priv->tx_config, port_base + TxConfig);
+}
+
+static void _sc92031_enable_tx_rx(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+
+	priv->rx_config |= RxEnb;
+	priv->tx_config |= TxEnb;
+	iowrite32(priv->rx_config, port_base + RxConfig);
+	iowrite32(priv->tx_config, port_base + TxConfig);
+}
+
+static void _sc92031_tx_free(struct net_device *dev,
+		struct sc92031_tx_info *info)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	struct pci_dev *pdev = priv->pdev;
+
+	pci_dma_sync_single_for_cpu(pdev, info->bounce_buffer_dma_addr,
+			TX_BUF_SIZE, PCI_DMA_TODEVICE);
+}
+
+static void _sc92031_tx_clear(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	unsigned entry;
+
+	while (priv->tx_head - priv->tx_tail > 0) {
+		entry = priv->tx_tail++ % NUM_TX_DESC;
+
+		_sc92031_tx_free(dev, &priv->tx_info[entry]);
+		priv->stats.tx_dropped++;
+	}
+	priv->tx_head = priv->tx_tail = 0;
+}
+
+static void _sc92031_set_mar(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+	u32 mar0 = 0, mar1 = 0;
+
+	if ((dev->flags & IFF_PROMISC)
+			|| dev->mc_count > multicast_filter_limit
+			|| (dev->flags & IFF_ALLMULTI))
+		mar0 = mar1 = 0xffffffff;
+	else if (dev->flags & IFF_MULTICAST) {
+		struct dev_mc_list *mc_list;
+
+		for (mc_list = dev->mc_list; mc_list; mc_list = mc_list->next) {
+			u32 crc;
+			unsigned bit = 0;
+
+			crc = ~ether_crc(ETH_ALEN, mc_list->dmi_addr);
+			crc >>= 24;
+
+			if (crc & 0x01)	bit |= 0x02;
+			if (crc & 0x02)	bit |= 0x01;
+			if (crc & 0x10)	bit |= 0x20;
+			if (crc & 0x20)	bit |= 0x10;
+			if (crc & 0x40)	bit |= 0x08;
+			if (crc & 0x80)	bit |= 0x04;
+
+			if (bit > 31)
+				mar0 |= 0x1 << (bit - 32);
+			else
+				mar1 |= 0x1 << bit;
+		}
+	}
+
+	iowrite32(mar0, port_base + MAR0);
+	iowrite32(mar1, port_base + MAR0 + 4);
+}
+
+static void _sc92031_set_rx_config(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+	unsigned int old_mc_flags;
+	u32 rx_config_bits = 0;
+
+	old_mc_flags = priv->mc_flags;
+
+	if (dev->flags & IFF_PROMISC)
+		rx_config_bits |= RxSmall | RxHuge | RxErr | RxBroadcast
+				| RxMulticast | RxAllphys;
+
+	if (dev->flags & (IFF_ALLMULTI | IFF_MULTICAST))
+		rx_config_bits |= RxMulticast;
+
+	if (dev->flags & IFF_BROADCAST)
+		rx_config_bits |= RxBroadcast;
+
+	priv->rx_config &= ~(RxSmall | RxHuge | RxErr | RxBroadcast
+			| RxMulticast | RxAllphys);
+	priv->rx_config |= rx_config_bits;
+
+	priv->mc_flags = dev->flags & (IFF_PROMISC | IFF_ALLMULTI
+			| IFF_MULTICAST | IFF_BROADCAST);
+
+	if (netif_carrier_ok(dev) && priv->mc_flags != old_mc_flags)
+		iowrite32(priv->rx_config, port_base + RxConfig);
+}
+
+static int _sc92031_check_media(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+	u16 bmsr;
+
+	bmsr = _sc92031_mii_read(port_base, MII_BMSR);
+	if (bmsr & BMSR_LSTATUS) {
+		u32 speed_100, duplex_full;	/* used as boolean values */
+		u32 flow_ctrl_config = 0;
+		u16 output_status = _sc92031_mii_read(port_base,
+				MII_OutputStatus);
+		_sc92031_mii_scan(port_base);
+
+		speed_100 = output_status & 0x2;
+		duplex_full = output_status & 0x4;
+
+		/* Initial Tx/Rx configuration */
+		priv->rx_config = (0x40 << LowThresholdShift) | (0x1c0 << HighThresholdShift);
+		priv->tx_config = 0x48800000;
+
+		/* NOTE: vendor driver had dead code here to enable tx padding */
+
+		if (!speed_100)
+			priv->tx_config |= 0x80000;
+
+		// configure rx mode
+		_sc92031_set_rx_config(dev);
+
+		if (duplex_full) {
+			priv->rx_config |= RxFullDx;
+			priv->tx_config |= TxFullDx;
+			flow_ctrl_config = FlowCtrlFullDX | FlowCtrlEnb;
+		} else {
+			priv->rx_config &= ~RxFullDx;
+			priv->tx_config &= ~TxFullDx;
+		}
+
+		_sc92031_set_mar(dev);
+		_sc92031_set_rx_config(dev);
+		_sc92031_enable_tx_rx(dev);
+		iowrite32(flow_ctrl_config, port_base + FlowCtrlConfig);
+
+		netif_carrier_on(dev);
+
+		if (printk_ratelimit())
+			printk(KERN_INFO "%s: link up, %sMbps, %s-duplex\n",
+				dev->name,
+				speed_100 ? "100" : "10",
+				duplex_full ? "full" : "half");
+		return 1;
+	} else {
+		_sc92031_mii_scan(port_base);
+
+		netif_carrier_off(dev);
+
+		_sc92031_disable_tx_rx(dev);
+
+		if (printk_ratelimit())
+			printk(KERN_INFO "%s: link down\n", dev->name);
+		return 0;
+	}
+}
+
+static void _sc92031_phy_reset(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+	u32 phy_ctrl;
+
+	phy_ctrl = ioread32(port_base + PhyCtrl);
+	phy_ctrl &= ~(PhyCtrlDux | PhyCtrlSpd100 | PhyCtrlSpd10);
+	phy_ctrl |= PhyCtrlAne | PhyCtrlReset;
+
+	switch (media) {
+	default:
+	case AUTOSELECT:
+		phy_ctrl |= PhyCtrlDux | PhyCtrlSpd100 | PhyCtrlSpd10;
+		break;
+	case M10_HALF:
+		phy_ctrl |= PhyCtrlSpd10;
+		break;
+	case M10_FULL:
+		phy_ctrl |= PhyCtrlDux | PhyCtrlSpd10;
+		break;
+	case M100_HALF:
+		phy_ctrl |= PhyCtrlSpd100;
+		break;
+	case M100_FULL:
+		phy_ctrl |= PhyCtrlDux | PhyCtrlSpd100;
+		break;
+	}
+
+	iowrite32(phy_ctrl, port_base + PhyCtrl);
+	mdelay(10);
+
+	phy_ctrl &= ~PhyCtrlReset;
+	iowrite32(phy_ctrl, port_base + PhyCtrl);
+	mdelay(1);
+
+	_sc92031_mii_write(port_base, MII_JAB,
+			PHY_16_JAB_ENB | PHY_16_PORT_ENB);
+	_sc92031_mii_scan(port_base);
+
+	netif_carrier_off(dev);
+	netif_stop_queue(dev);
+}
+
+static void _sc92031_reset(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+
+	/* disable PM */
+	iowrite32(0, port_base + PMConfig);
+
+	/* soft reset the chip */
+	iowrite32(Cfg0_Reset, port_base + Config0);
+	mdelay(200);
+	iowrite32(0, port_base + Config0);
+	mdelay(10);
+
+	/* disable interrupts */
+	iowrite32(0, port_base + IntrMask);
+
+	/* clear multicast address */
+	iowrite32(0, port_base + MAR0);
+	iowrite32(0, port_base + MAR0 + 4);
+
+	/* init rx ring */
+	iowrite32(priv->rx_ring_dma_addr, port_base + RxbufAddr);
+	priv->rx_ring_tail = priv->rx_ring_dma_addr;
+
+	/* init tx ring */
+	_sc92031_tx_clear(dev);
+
+	/* clear old register values */
+	priv->intr_status = 0;
+	priv->rx_config = 0;
+	priv->tx_config = 0;
+	priv->mc_flags = 0;
+
+	/* configure rx buffer size */
+	/* NOTE: vendor driver had dead code here to enable early tx/rx */
+	iowrite32(Cfg1_Rcv64K, port_base + Config1);
+
+	_sc92031_phy_reset(dev);
+	_sc92031_check_media(dev);
+
+	/* calculate rx fifo overflow */
+	priv->rx_value = 0;
+
+	/* enable PM */
+	iowrite32(priv->pm_config, port_base + PMConfig);
+
+	/* clear intr register */
+	ioread32(port_base + IntrStatus);
+}
+
+static void _sc92031_tx_tasklet(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+
+	unsigned old_tx_tail;
+	unsigned entry;
+	u32 tx_status;
+
+	old_tx_tail = priv->tx_tail;
+	while (priv->tx_head - priv->tx_tail > 0) {
+		entry = priv->tx_tail % NUM_TX_DESC;
+		tx_status = ioread32(port_base + TxStatus0 + entry * 4);
+
+		if (!(tx_status & (TxStatOK | TxUnderrun | TxAborted)))
+			break;
+
+		priv->tx_tail++;
+
+		_sc92031_tx_free(dev, &priv->tx_info[entry]);
+
+		if (tx_status & TxStatOK) {
+			priv->stats.tx_bytes += tx_status & 0x1fff;
+			priv->stats.tx_packets++;
+			/* Note: TxCarrierLost is always asserted at 100mbps. */
+			priv->stats.collisions += (tx_status >> 22) & 0xf;
+		}
+
+		if (tx_status & (TxOutOfWindow | TxAborted)) {
+			priv->stats.tx_errors++;
+
+			if (tx_status & TxAborted)
+				priv->stats.tx_aborted_errors++;
+
+			if (tx_status & TxCarrierLost)
+				priv->stats.tx_carrier_errors++;
+
+			if (tx_status & TxOutOfWindow)
+				priv->stats.tx_window_errors++;
+		}
+
+		if (tx_status & TxUnderrun)
+			priv->stats.tx_fifo_errors++;
+	}
+
+	if (priv->tx_tail != old_tx_tail)
+		if (netif_queue_stopped(dev))
+			netif_wake_queue(dev);
+}
+
+static void _sc92031_rx_tasklet_error(u32 rx_status,
+		struct sc92031_priv *priv, unsigned rx_size)
+{
+	if(rx_size > (MAX_ETH_FRAME_SIZE + 4) || rx_size < 16) {
+		priv->stats.rx_errors++;
+		priv->stats.rx_length_errors++;
+	}
+
+	if (!(rx_status & RxStatesOK)) {
+		priv->stats.rx_errors++;
+
+		if (rx_status & (RxHugeFrame | RxSmallFrame))
+			priv->stats.rx_length_errors++;
+
+		if (rx_status & RxBadAlign)
+			priv->stats.rx_frame_errors++;
+
+		if (!(rx_status & RxCRCOK))
+			priv->stats.rx_crc_errors++;
+	} else
+		priv->rx_loss++;
+}
+
+static void _sc92031_rx_tasklet(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+
+	dma_addr_t rx_ring_head;
+	unsigned rx_len;
+	unsigned rx_ring_offset;
+	void *rx_ring = priv->rx_ring;
+
+	rx_ring_head = ioread32(port_base + RxBufWPtr);
+	rmb();
+
+	/* rx_ring_head is only 17 bits in the RxBufWPtr register.
+	 * we need to change it to 32 bits physical address
+	 */
+	rx_ring_head &= (dma_addr_t)(RX_BUF_LEN - 1);
+	rx_ring_head |= priv->rx_ring_dma_addr & ~(dma_addr_t)(RX_BUF_LEN - 1);
+	if (rx_ring_head < priv->rx_ring_dma_addr)
+		rx_ring_head += RX_BUF_LEN;
+
+	if (rx_ring_head >= priv->rx_ring_tail)
+		rx_len = rx_ring_head - priv->rx_ring_tail;
+	else
+		rx_len = RX_BUF_LEN - (priv->rx_ring_tail - rx_ring_head);
+
+	if (!rx_len)
+		return;
+
+	if (unlikely(rx_len > RX_BUF_LEN)) {
+		if (printk_ratelimit())
+			printk(KERN_ERR "%s: rx packets length > rx buffer\n",
+					dev->name);
+		return;
+	}
+
+	rx_ring_offset = (priv->rx_ring_tail - priv->rx_ring_dma_addr) % RX_BUF_LEN;
+
+	while (rx_len) {
+		u32 rx_status;
+		unsigned rx_size, rx_size_align, pkt_size;
+		struct sk_buff *skb;
+
+		rx_status = le32_to_cpup((__le32 *)(rx_ring + rx_ring_offset));
+		rmb();
+
+		rx_size = rx_status >> 20;
+		rx_size_align = (rx_size + 3) & ~3;	// for 4 bytes aligned
+		pkt_size = rx_size - 4;	// Omit the four octet CRC from the length.
+
+		rx_ring_offset = (rx_ring_offset + 4) % RX_BUF_LEN;
+
+		if (unlikely(rx_status == 0
+				|| rx_size > (MAX_ETH_FRAME_SIZE + 4)
+				|| rx_size < 16
+				|| !(rx_status & RxStatesOK))) {
+			_sc92031_rx_tasklet_error(rx_status, priv, rx_size);
+			break;
+		}
+
+		if (unlikely(rx_size_align + 4 > rx_len)) {
+			if (printk_ratelimit())
+				printk(KERN_ERR "%s: rx_len is too small\n", dev->name);
+			break;
+		}
+
+		rx_len -= rx_size_align + 4;
+
+		skb = dev_alloc_skb(pkt_size + NET_IP_ALIGN);
+		if (unlikely(!skb)) {
+			if (printk_ratelimit())
+				printk(KERN_ERR "%s: Couldn't allocate a skb_buff for a packet of size %u\n",
+						dev->name, pkt_size);
+			goto next;
+		}
+
+		skb_reserve(skb, NET_IP_ALIGN);
+
+		if ((rx_ring_offset + pkt_size) > RX_BUF_LEN) {
+			memcpy(skb_put(skb, RX_BUF_LEN - rx_ring_offset),
+				rx_ring + rx_ring_offset, RX_BUF_LEN - rx_ring_offset);
+			memcpy(skb_put(skb, pkt_size - (RX_BUF_LEN - rx_ring_offset)),
+				rx_ring, pkt_size - (RX_BUF_LEN - rx_ring_offset));
+		} else {
+			memcpy(skb_put(skb, pkt_size), rx_ring + rx_ring_offset, pkt_size);
+		}
+
+		skb->dev = dev;
+		skb->protocol = eth_type_trans(skb, dev);
+		dev->last_rx = jiffies;
+		netif_rx(skb);
+
+		priv->stats.rx_bytes += pkt_size;
+		priv->stats.rx_packets++;
+
+		if (rx_status & Rx_Multicast)
+			priv->stats.multicast++;
+
+	next:
+		rx_ring_offset = (rx_ring_offset + rx_size_align) % RX_BUF_LEN;
+	}
+
+	priv->rx_ring_tail = rx_ring_head;
+	iowrite32(priv->rx_ring_tail, port_base + RxBufRPtr);
+}
+
+static void _sc92031_link_tasklet(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+
+	if (_sc92031_check_media(dev))
+		netif_wake_queue(dev);
+	else {
+		netif_stop_queue(dev);
+		priv->stats.tx_carrier_errors++;
+	}
+}
+
+static void sc92031_tasklet(unsigned long data)
+{
+	struct net_device *dev = (struct net_device *)data;
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+	u32 intr_status;
+
+	intr_status = xchg(&priv->intr_status, 0);
+
+	spin_lock(&priv->lock);
+
+	if (unlikely(!netif_running(dev)))
+		goto out;
+
+	if (intr_status & TxOK)
+		_sc92031_tx_tasklet(dev);
+
+	if (intr_status & RxOK)
+		_sc92031_rx_tasklet(dev);
+
+	if (intr_status & RxOverflow)
+		priv->stats.rx_errors++;
+
+	if (intr_status & TimeOut) {
+		priv->stats.rx_errors++;
+		priv->stats.rx_length_errors++;
+	}
+
+	if (intr_status & (LinkFail | LinkOK))
+		_sc92031_link_tasklet(dev);
+
+out:
+	iowrite32(IntrBits, port_base + IntrMask);
+	mmiowb();
+
+	spin_unlock(&priv->lock);
+}
+
+static irqreturn_t sc92031_interrupt(int irq, void *dev_id)
+{
+	struct net_device *dev = dev_id;
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+	u32 intr_status, old_intr_status, new_intr_status;
+
+	intr_status = ioread32(port_base + IntrStatus);
+	if (unlikely(intr_status == 0xffffffff))
+		return IRQ_NONE;
+
+	intr_status &= IntrBits;
+	if (!intr_status)
+		return IRQ_NONE;
+
+	do {
+		old_intr_status = priv->intr_status;
+		new_intr_status = old_intr_status | intr_status;
+	} while(cmpxchg(&priv->intr_status, old_intr_status, new_intr_status)
+			!= old_intr_status);
+
+	iowrite32(0, port_base + IntrMask);
+	mmiowb();
+
+	tasklet_schedule(&priv->tasklet);
+
+	return IRQ_HANDLED;
+}
+
+static struct net_device_stats *sc92031_get_stats(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+
+	// FIXME I do not understand what is this trying to do.
+	if (netif_running(dev)) {
+		int temp;
+
+		spin_lock_bh(&priv->lock);
+
+		/* Update the error count. */
+		temp = (ioread32(port_base + RxStatus0) >> 16) & 0xffff;
+
+		if (temp == 0xffff) {
+			priv->rx_value += temp;
+			priv->stats.rx_fifo_errors = priv->rx_value;
+		} else {
+			priv->stats.rx_fifo_errors = temp + priv->rx_value;
+		}
+
+		spin_unlock_bh(&priv->lock);
+	}
+
+	return &priv->stats;
+}
+
+static int sc92031_start_xmit(struct sk_buff *skb, struct net_device *dev)
+{
+	int err = 0;
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+	struct pci_dev *pdev = priv->pdev;
+
+	unsigned len;
+	unsigned entry;
+	u32 tx_status;
+
+	if (unlikely(skb->len > TX_BUF_SIZE)) {
+		err = -EMSGSIZE;
+		goto out;
+	}
+
+	spin_lock_bh(&priv->lock);
+
+	if (unlikely(!netif_carrier_ok(dev))) {
+		err = -ENOLINK;
+		goto out_unlock;
+	}
+
+	BUG_ON(priv->tx_head - priv->tx_tail >= NUM_TX_DESC);
+
+	entry = priv->tx_head++ % NUM_TX_DESC;
+
+	len = skb->len;
+	memcpy(priv->tx_info[entry].bounce_buffer, skb->data, len);
+	if (unlikely(len < ETH_ZLEN)) {
+		memset(priv->tx_info[entry].bounce_buffer + len,
+				0, ETH_ZLEN - len);
+		len = ETH_ZLEN;
+	}
+	pci_dma_sync_single_for_device(pdev,
+			priv->tx_info[entry].bounce_buffer_dma_addr,
+			TX_BUF_SIZE, PCI_DMA_TODEVICE);
+
+	if (len < 100)
+		tx_status = len;
+	else if (len < 300)
+		tx_status = 0x30000 | len;
+	else
+		tx_status = 0x50000 | len;
+
+	iowrite32(priv->tx_info[entry].bounce_buffer_dma_addr,
+			port_base + TxAddr0 + entry * 4);
+	iowrite32(tx_status, port_base + TxStatus0 + entry * 4);
+	mmiowb();
+
+	dev->trans_start = jiffies;
+
+	if (priv->tx_head - priv->tx_tail >= NUM_TX_DESC)
+		netif_stop_queue(dev);
+
+out_unlock:
+	spin_unlock_bh(&priv->lock);
+
+out:
+	// FIXME: which variant of dev_kfree is the right one here?
+	dev_kfree_skb_any(skb);
+
+	return err;
+}
+
+static int sc92031_open(struct net_device *dev)
+{
+	int err;
+	struct sc92031_priv *priv = netdev_priv(dev);
+	struct pci_dev *pdev = priv->pdev;
+	int entry;
+
+	priv->rx_ring = pci_alloc_consistent(pdev, RX_BUF_LEN,
+			&priv->rx_ring_dma_addr);
+	if (unlikely(!priv->rx_ring)) {
+		err = -ENOMEM;
+		goto out_alloc_rx_ring;
+	}
+
+	for (entry = 0; entry < NUM_TX_DESC; entry++) {
+		/* GFP_DMA32 is not always needed, but I don't know how
+		 * to use it only when there is no IOMMU.
+		 * Something like pci_dma_kmalloc or pci_dma_gfp_flags would
+		 * be useful here. */
+		priv->tx_info[entry].bounce_buffer
+			= kmalloc(TX_BUF_SIZE, GFP_KERNEL | GFP_DMA32);
+		if (unlikely(!priv->tx_info[entry].bounce_buffer)) {
+			err = -ENOMEM;
+			goto out_alloc_tx_ring;
+		}
+
+		priv->tx_info[entry].bounce_buffer_dma_addr
+			= pci_map_single(pdev,
+					priv->tx_info[entry].bounce_buffer,
+					TX_BUF_SIZE, PCI_DMA_TODEVICE);
+		if (unlikely(pci_dma_mapping_error(
+				priv->tx_info[entry].bounce_buffer_dma_addr))) {
+			err = -ENOMEM;
+			kfree(priv->tx_info[entry].bounce_buffer);
+			goto out_alloc_tx_ring;
+		}
+
+		pci_dma_sync_single_for_cpu(pdev,
+				priv->tx_info[entry].bounce_buffer_dma_addr,
+				TX_BUF_SIZE, PCI_DMA_TODEVICE);
+	}
+	priv->tx_head = priv->tx_tail = 0;
+
+	err = request_irq(pdev->irq, sc92031_interrupt,
+			SA_SHIRQ, dev->name, dev);
+	if (unlikely(err < 0))
+		goto out_request_irq;
+
+	priv->pm_config = 0;
+
+	sc92031_disable_interrupts(dev);
+	spin_lock(&priv->lock);
+
+	_sc92031_reset(dev);
+	mmiowb();
+
+	spin_unlock(&priv->lock);
+	sc92031_enable_interrupts(dev);
+
+	if (netif_carrier_ok(dev))
+		netif_start_queue(dev);
+	else
+		netif_tx_disable(dev);
+
+	return 0;
+
+out_request_irq:
+out_alloc_tx_ring:
+	for (entry--; entry >= 0; entry--) {
+		pci_unmap_single(pdev,
+				priv->tx_info[entry].bounce_buffer_dma_addr,
+				TX_BUF_SIZE, PCI_DMA_TODEVICE);
+		kfree(priv->tx_info[entry].bounce_buffer);
+	}
+
+	pci_free_consistent(pdev, RX_BUF_LEN, priv->rx_ring,
+			priv->rx_ring_dma_addr);
+out_alloc_rx_ring:
+	return err;
+}
+
+static int sc92031_stop(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	struct pci_dev *pdev = priv->pdev;
+	unsigned entry;
+
+	netif_tx_disable(dev);
+
+	/* Disable interrupts, stop Tx and Rx. */
+	sc92031_disable_interrupts(dev);
+
+	spin_lock(&priv->lock);
+
+	_sc92031_disable_tx_rx(dev);
+	_sc92031_tx_clear(dev);
+	mmiowb();
+
+	spin_unlock(&priv->lock);
+
+	free_irq(pdev->irq, dev);
+	for (entry = 0; entry < NUM_TX_DESC; entry++) {
+		pci_unmap_single(pdev,
+				priv->tx_info[entry].bounce_buffer_dma_addr,
+				TX_BUF_SIZE, PCI_DMA_TODEVICE);
+		kfree(priv->tx_info[entry].bounce_buffer);
+	}
+	pci_free_consistent(pdev, RX_BUF_LEN, priv->rx_ring,
+			priv->rx_ring_dma_addr);
+
+	return 0;
+}
+
+static void sc92031_set_multicast_list(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+
+	spin_lock_bh(&priv->lock);
+
+	_sc92031_set_mar(dev);
+	_sc92031_set_rx_config(dev);
+	mmiowb();
+
+	spin_unlock_bh(&priv->lock);
+}
+
+static void sc92031_tx_timeout(struct net_device *dev)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+
+	/* Disable interrupts by clearing the interrupt mask.*/
+	sc92031_disable_interrupts(dev);
+
+	spin_lock(&priv->lock);
+
+	priv->tx_timeouts++;
+
+	_sc92031_reset(dev);
+	mmiowb();
+
+	spin_unlock(&priv->lock);
+
+	/* enable interrupts */
+	sc92031_enable_interrupts(dev);
+
+	if (netif_carrier_ok(dev))
+		netif_wake_queue(dev);
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void sc92031_poll_controller(struct net_device *dev)
+{
+	disable_irq(dev->irq);
+	sc92031_interrupt(dev->irq, dev);
+	// FIXME: is that enough or do I need to run the tasklet too?
+	enable_irq(dev->irq);
+}
+#endif
+
+static int sc92031_ethtool_get_settings(struct net_device *dev,
+		struct ethtool_cmd *cmd)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+	u8 phy_address;
+	u32 phy_ctrl;
+	u16 output_status;
+
+	spin_lock_bh(&priv->lock);
+
+	phy_address = ioread32(port_base + Miicmd1) >> 27;
+	phy_ctrl = ioread32(port_base + PhyCtrl);
+
+	output_status = _sc92031_mii_read(port_base, MII_OutputStatus);
+	_sc92031_mii_scan(port_base);
+	mmiowb();
+
+	spin_unlock_bh(&priv->lock);
+
+	cmd->supported = SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full
+			| SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full
+			| SUPPORTED_Autoneg | SUPPORTED_TP | SUPPORTED_MII;
+
+	cmd->advertising = ADVERTISED_TP | ADVERTISED_MII;
+
+	if ((phy_ctrl & (PhyCtrlDux | PhyCtrlSpd100 | PhyCtrlSpd10))
+			== (PhyCtrlDux | PhyCtrlSpd100 | PhyCtrlSpd10))
+		cmd->advertising |= ADVERTISED_Autoneg;
+
+	if ((phy_ctrl & PhyCtrlSpd10) == PhyCtrlSpd10)
+		cmd->advertising |= ADVERTISED_10baseT_Half;
+
+	if ((phy_ctrl & (PhyCtrlSpd10 | PhyCtrlDux))
+			== (PhyCtrlSpd10 | PhyCtrlDux))
+		cmd->advertising |= ADVERTISED_10baseT_Full;
+
+	if ((phy_ctrl & PhyCtrlSpd100) == PhyCtrlSpd100)
+		cmd->advertising |= ADVERTISED_100baseT_Half;
+
+	if ((phy_ctrl & (PhyCtrlSpd100 | PhyCtrlDux))
+			== (PhyCtrlSpd100 | PhyCtrlDux))
+		cmd->advertising |= ADVERTISED_100baseT_Full;
+
+	if (phy_ctrl & PhyCtrlAne)
+		cmd->advertising |= ADVERTISED_Autoneg;
+
+	cmd->speed = (output_status & 0x2) ? SPEED_100 : SPEED_10;
+	cmd->duplex = (output_status & 0x4) ? DUPLEX_FULL : DUPLEX_HALF;
+	cmd->port = PORT_MII;
+	cmd->phy_address = phy_address;
+	cmd->transceiver = XCVR_INTERNAL;
+	cmd->autoneg = (phy_ctrl & PhyCtrlAne) ? AUTONEG_ENABLE : AUTONEG_DISABLE;
+
+	return 0;
+}
+
+static int sc92031_ethtool_set_settings(struct net_device *dev,
+		struct ethtool_cmd *cmd)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+	u32 phy_ctrl;
+	u32 old_phy_ctrl;
+
+	if (!(cmd->speed == SPEED_10 || cmd->speed == SPEED_100))
+		return -EINVAL;
+	if (!(cmd->duplex == DUPLEX_HALF || cmd->duplex == DUPLEX_FULL))
+		return -EINVAL;
+	if (!(cmd->port == PORT_MII))
+		return -EINVAL;
+	if (!(cmd->phy_address == 0x1f))
+		return -EINVAL;
+	if (!(cmd->transceiver == XCVR_INTERNAL))
+		return -EINVAL;
+	if (!(cmd->autoneg == AUTONEG_DISABLE || cmd->autoneg == AUTONEG_ENABLE))
+		return -EINVAL;
+
+	if (cmd->autoneg == AUTONEG_ENABLE) {
+		if (!(cmd->advertising & (ADVERTISED_Autoneg
+				| ADVERTISED_100baseT_Full
+				| ADVERTISED_100baseT_Half
+				| ADVERTISED_10baseT_Full
+				| ADVERTISED_10baseT_Half)))
+			return -EINVAL;
+
+		phy_ctrl = PhyCtrlAne;
+
+		// FIXME: I'm not sure what the original code was trying to do
+		if (cmd->advertising & ADVERTISED_Autoneg)
+			phy_ctrl |= PhyCtrlDux | PhyCtrlSpd100 | PhyCtrlSpd10;
+		if (cmd->advertising & ADVERTISED_100baseT_Full)
+			phy_ctrl |= PhyCtrlDux | PhyCtrlSpd100;
+		if (cmd->advertising & ADVERTISED_100baseT_Half)
+			phy_ctrl |= PhyCtrlSpd100;
+		if (cmd->advertising & ADVERTISED_10baseT_Full)
+			phy_ctrl |= PhyCtrlSpd10 | PhyCtrlDux;
+		if (cmd->advertising & ADVERTISED_10baseT_Half)
+			phy_ctrl |= PhyCtrlSpd10;
+	} else {
+		// FIXME: Whole branch guessed
+		phy_ctrl = 0;
+
+		if (cmd->speed == SPEED_10)
+			phy_ctrl |= PhyCtrlSpd10;
+		else /* cmd->speed == SPEED_100 */
+			phy_ctrl |= PhyCtrlSpd100;
+
+		if (cmd->duplex == DUPLEX_FULL)
+			phy_ctrl |= PhyCtrlDux;
+	}
+
+	spin_lock_bh(&priv->lock);
+
+	old_phy_ctrl = ioread32(port_base + PhyCtrl);
+	phy_ctrl |= old_phy_ctrl & ~(PhyCtrlAne | PhyCtrlDux
+			| PhyCtrlSpd100 | PhyCtrlSpd10);
+	if (phy_ctrl != old_phy_ctrl)
+		iowrite32(phy_ctrl, port_base + PhyCtrl);
+
+	spin_unlock_bh(&priv->lock);
+
+	return 0;
+}
+
+static void sc92031_ethtool_get_drvinfo(struct net_device *dev,
+		struct ethtool_drvinfo *drvinfo)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	struct pci_dev *pdev = priv->pdev;
+
+	strcpy(drvinfo->driver, SC92031_NAME);
+	strcpy(drvinfo->version, SC92031_VERSION);
+	strcpy(drvinfo->bus_info, pci_name(pdev));
+}
+
+static void sc92031_ethtool_get_wol(struct net_device *dev,
+		struct ethtool_wolinfo *wolinfo)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+	u32 pm_config;
+
+	spin_lock_bh(&priv->lock);
+	pm_config = ioread32(port_base + PMConfig);
+	spin_unlock_bh(&priv->lock);
+
+	// FIXME: Guessed
+	wolinfo->supported = WAKE_PHY | WAKE_MAGIC
+			| WAKE_UCAST | WAKE_MCAST | WAKE_BCAST;
+	wolinfo->wolopts = 0;
+
+	if (pm_config & PM_LinkUp)
+		wolinfo->wolopts |= WAKE_PHY;
+
+	if (pm_config & PM_Magic)
+		wolinfo->wolopts |= WAKE_MAGIC;
+
+	if (pm_config & PM_WakeUp)
+		// FIXME: Guessed
+		wolinfo->wolopts |= WAKE_UCAST | WAKE_MCAST | WAKE_BCAST;
+}
+
+static int sc92031_ethtool_set_wol(struct net_device *dev,
+		struct ethtool_wolinfo *wolinfo)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+	u32 pm_config;
+
+	spin_lock_bh(&priv->lock);
+
+	pm_config = ioread32(port_base + PMConfig)
+			& ~(PM_LinkUp | PM_Magic | PM_WakeUp);
+
+	if (wolinfo->wolopts & WAKE_PHY)
+		pm_config |= PM_LinkUp;
+
+	if (wolinfo->wolopts & WAKE_MAGIC)
+		pm_config |= PM_Magic;
+
+	// FIXME: Guessed
+	if (wolinfo->wolopts & (WAKE_UCAST | WAKE_MCAST | WAKE_BCAST))
+		pm_config |= PM_WakeUp;
+
+	priv->pm_config = pm_config;
+	iowrite32(pm_config, port_base + PMConfig);
+	mmiowb();
+
+	spin_unlock_bh(&priv->lock);
+
+	return 0;
+}
+
+static int sc92031_ethtool_nway_reset(struct net_device *dev)
+{
+	int err = 0;
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem *port_base = priv->port_base;
+	u16 bmcr;
+
+	spin_lock_bh(&priv->lock);
+
+	bmcr = _sc92031_mii_read(port_base, MII_BMCR);
+	if (!(bmcr & BMCR_ANENABLE)) {
+		err = -EINVAL;
+		goto out;
+	}
+
+	_sc92031_mii_write(port_base, MII_BMCR, bmcr | BMCR_ANRESTART);
+
+out:
+	_sc92031_mii_scan(port_base);
+	mmiowb();
+
+	spin_unlock_bh(&priv->lock);
+
+	return err;
+}
+
+static const char sc92031_ethtool_stats_strings[SILAN_STATS_NUM][ETH_GSTRING_LEN] = {
+	"tx_timeout",
+	"rx_loss",
+};
+
+static void sc92031_ethtool_get_strings(struct net_device *dev,
+		u32 stringset, u8 *data)
+{
+	if (stringset == ETH_SS_STATS)
+		memcpy(data, sc92031_ethtool_stats_strings,
+				SILAN_STATS_NUM * ETH_GSTRING_LEN);
+}
+
+static int sc92031_ethtool_get_stats_count(struct net_device *dev)
+{
+	return SILAN_STATS_NUM;
+}
+
+static void sc92031_ethtool_get_ethtool_stats(struct net_device *dev,
+		struct ethtool_stats *stats, u64 *data)
+{
+	struct sc92031_priv *priv = netdev_priv(dev);
+
+	spin_lock_bh(&priv->lock);
+	data[0] = priv->tx_timeouts;
+	data[1] = priv->rx_loss;
+	spin_unlock_bh(&priv->lock);	
+}
+
+static struct ethtool_ops sc92031_ethtool_ops = {
+	.get_settings		= sc92031_ethtool_get_settings,
+	.set_settings		= sc92031_ethtool_set_settings,
+	.get_drvinfo		= sc92031_ethtool_get_drvinfo,
+	.get_wol		= sc92031_ethtool_get_wol,
+	.set_wol		= sc92031_ethtool_set_wol,
+	.nway_reset		= sc92031_ethtool_nway_reset,
+	.get_link		= ethtool_op_get_link,
+	.get_tx_csum		= ethtool_op_get_tx_csum,
+	.get_sg			= ethtool_op_get_sg,
+	.get_tso		= ethtool_op_get_tso,
+	.get_strings		= sc92031_ethtool_get_strings,
+	.get_stats_count	= sc92031_ethtool_get_stats_count,
+	.get_ethtool_stats	= sc92031_ethtool_get_ethtool_stats,
+	.get_perm_addr		= ethtool_op_get_perm_addr,
+	.get_ufo		= ethtool_op_get_ufo,
+};
+
+static int __devinit sc92031_probe(struct pci_dev *pdev,
+		const struct pci_device_id *id)
+{
+	int err;
+	void __iomem* port_base;
+	struct net_device *dev;
+	struct sc92031_priv *priv;
+	u32 mac0, mac1;
+
+	err = pci_enable_device(pdev);
+	if (unlikely(err < 0))
+		goto out_enable_device;
+
+	pci_set_master(pdev);
+
+	err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
+	if (unlikely(err < 0))
+		goto out_set_dma_mask;
+
+	err = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
+	if (unlikely(err < 0))
+		goto out_set_dma_mask;
+
+	err = pci_request_regions(pdev, SC92031_NAME);
+	if (unlikely(err < 0))
+		goto out_request_regions;
+
+	port_base = pci_iomap(pdev, SC92031_USE_BAR, 0);
+	if (unlikely(!port_base)) {
+		err = -EIO;
+		goto out_iomap;
+	}
+
+	dev = alloc_etherdev(sizeof(struct sc92031_priv));
+	if (unlikely(!dev)) {
+		err = -ENOMEM;
+		goto out_alloc_etherdev;
+	}
+
+	pci_set_drvdata(pdev, dev);
+
+	dev->base_addr = pci_resource_start(pdev, SC92031_USE_BAR);
+	dev->irq = pdev->irq;
+
+	dev->get_stats		= sc92031_get_stats;
+	dev->ethtool_ops	= &sc92031_ethtool_ops;
+	dev->hard_start_xmit	= sc92031_start_xmit;
+	dev->watchdog_timeo	= TX_TIMEOUT;
+	dev->open		= sc92031_open;
+	dev->stop		= sc92031_stop;
+	dev->set_multicast_list	= sc92031_set_multicast_list;
+	dev->set_mac_address	= NULL;	/* override ether_setup */
+	dev->tx_timeout		= sc92031_tx_timeout;
+#ifdef CONFIG_NET_POLL_CONTROLLER
+	dev->poll_controller	= sc92031_poll_controller;
+#endif
+
+	priv = netdev_priv(dev);
+	spin_lock_init(&priv->lock);
+	priv->port_base = port_base;
+	priv->pdev = pdev;
+	tasklet_init(&priv->tasklet, sc92031_tasklet, (unsigned long)dev);
+
+	/* PCI PM Wakeup */
+	iowrite32((~PM_LongWF & ~PM_LWPTN) | PM_Enable, port_base + PMConfig);
+
+	mac0 = ioread32(port_base + MAC0);
+	mac1 = ioread32(port_base + MAC0 + 4);
+	dev->dev_addr[0] = dev->perm_addr[0] = mac0 >> 24;
+	dev->dev_addr[1] = dev->perm_addr[1] = mac0 >> 16;
+	dev->dev_addr[2] = dev->perm_addr[2] = mac0 >> 8;
+	dev->dev_addr[3] = dev->perm_addr[3] = mac0;
+	dev->dev_addr[4] = dev->perm_addr[4] = mac1 >> 8;
+	dev->dev_addr[5] = dev->perm_addr[5] = mac1;
+
+	err = register_netdev(dev);
+	if (err < 0)
+		goto out_register_netdev;
+
+	return 0;
+
+out_register_netdev:
+	free_netdev(dev);
+out_alloc_etherdev:
+	pci_iounmap(pdev, port_base);
+out_iomap:
+	pci_release_regions(pdev);
+out_request_regions:
+out_set_dma_mask:
+	pci_disable_device(pdev);
+out_enable_device:
+	return err;
+}
+
+static void __devexit sc92031_remove(struct pci_dev *pdev)
+{
+	struct net_device *dev = pci_get_drvdata(pdev);
+	struct sc92031_priv *priv = netdev_priv(dev);
+	void __iomem* port_base = priv->port_base;
+
+	unregister_netdev(dev);
+	free_netdev(dev);
+	pci_iounmap(pdev, port_base);
+	pci_release_regions(pdev);
+	pci_disable_device(pdev);
+}
+
+static int sc92031_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+	struct net_device *dev = pci_get_drvdata(pdev);
+	struct sc92031_priv *priv = netdev_priv(dev);
+
+	pci_save_state(pdev);
+
+	if (!netif_running(dev))
+		goto out;
+
+	netif_device_detach(dev);
+
+	/* Disable interrupts, stop Tx and Rx. */
+	sc92031_disable_interrupts(dev);
+
+	spin_lock(&priv->lock);
+
+	_sc92031_disable_tx_rx(dev);
+	_sc92031_tx_clear(dev);
+	mmiowb();
+
+	spin_unlock(&priv->lock);
+
+out:
+	pci_set_power_state(pdev, pci_choose_state(pdev, state));
+
+	return 0;
+}
+
+static int sc92031_resume(struct pci_dev *pdev)
+{
+	struct net_device *dev = pci_get_drvdata(pdev);
+	struct sc92031_priv *priv = netdev_priv(dev);
+
+	pci_restore_state(pdev);
+	pci_set_power_state(pdev, PCI_D0);
+
+	if (!netif_running(dev))
+		goto out;
+
+	sc92031_disable_interrupts(dev);
+	spin_lock(&priv->lock);
+
+	_sc92031_reset(dev);
+	mmiowb();
+
+	spin_unlock(&priv->lock);
+	sc92031_enable_interrupts(dev);
+
+	netif_device_attach(dev);
+
+	if (netif_carrier_ok(dev))
+		netif_wake_queue(dev);
+	else
+		netif_tx_disable(dev);
+
+out:
+	return 0;
+}
+
+static struct pci_device_id sc92031_pci_device_id_table[] __devinitdata = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_SILAN, PCI_DEVICE_ID_SILAN_SC92031) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_SILAN, PCI_DEVICE_ID_SILAN_8139D) },
+	{ 0, }
+};
+MODULE_DEVICE_TABLE(pci, sc92031_pci_device_id_table);
+
+static struct pci_driver sc92031_pci_driver = {
+	.name		= SC92031_NAME,
+	.id_table	= sc92031_pci_device_id_table,
+	.probe		= sc92031_probe,
+	.remove		= __devexit_p(sc92031_remove),
+	.suspend	= sc92031_suspend,
+	.resume		= sc92031_resume,
+};
+
+static int __init sc92031_init(void)
+{
+	printk(KERN_INFO SC92031_DESCRIPTION " " SC92031_VERSION "\n");
+	return pci_register_driver(&sc92031_pci_driver);
+}
+
+static void __exit sc92031_exit(void)
+{
+	pci_unregister_driver(&sc92031_pci_driver);
+}
+
+module_init(sc92031_init);
+module_exit(sc92031_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Cesar Eduardo Barros <cesarb@cesarb.net>");
+MODULE_DESCRIPTION(SC92031_DESCRIPTION);
+MODULE_VERSION(SC92031_VERSION);

-- 
Cesar Eduardo Barros
cesarb@cesarb.net
cesar.barros@gmail.com

Re: [PATCH] 2.6 driver for Silan SC92031

[Jeff Garzik]

Cesar Eduardo Barros wrote:
> From: Cesar Eduardo Barros <cesarb@cesarb.net>
> 
> This is a driver for the Silan SC92031/Rsltek 8139D NIC chip. It's a
> rewrite of the vendor 2.4 driver for 2.6, and has been lightly tested
> on a 2.6.17 x86-64 kernel with the Ubuntu patches (as a out-of-tree
> module only).
> 
> This chip is found on at least one counterfeit Encore ENL832-TX-RENT
> NIC [1], which came with a mini-CD with the 2.4 driver. A slightly
> older version of the driver was found at [2]. The main difference
> between them is that the newer one has a small bugfix in the RX path,
> a lot of gratuitous renaming of functions, all the printable strings
> changed to show as a "Rsltek 8139D" [sic], and a PCI ID of 8139 instead
> of 2031.
> 
> This patch has been modified to apply cleanly on 2.6.19; to run on
> 2.6.17, just add back the struct pt_regs* argument to the interrupt
> handler and to its call at poll_controller(). It compiles on 2.6.19 for
> x86-64 as a module.
> 
> [1] See http://www.encore-usa.com/faq.php under ENL832-TX-RENT for more
>     information
> [2] Look for SL_LINUX.ZIP (which is really a .tar.gz) at
>     http://broadbandforum.in/dataone_Intex_LAN_cardlinux-t4207-s15.html
> 
> Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>

Seems like it would be best to modify the existing 8139 driver...

	Jeff

Re: [PATCH] 2.6 driver for Silan SC92031

[Cesar Eduardo Barros]

Jeff Garzik escreveu:
> Cesar Eduardo Barros wrote:
>> From: Cesar Eduardo Barros <cesarb@cesarb.net>
>>
>> This is a driver for the Silan SC92031/Rsltek 8139D NIC chip. It's a
>> rewrite of the vendor 2.4 driver for 2.6, and has been lightly tested
>> on a 2.6.17 x86-64 kernel with the Ubuntu patches (as a out-of-tree
>> module only).
>>
> 
> Seems like it would be best to modify the existing 8139 driver...

I'm not sure it would help. Either the hardware differences are too 
large (for instance, the MII/link part, where the way the vendor driver 
did things implies the MII has only the two basic registers plus two 
vendor registers, meaning I simply cannot use the generic mii code) or 
the code is already modified from the 8139 driver (the vendor driver 
seems to be based on an old version of either pci-skeleton.c or 
8139too.c, and I based my rewrite on the vendor driver).

Of course, one thing I probably will copy from 8139too.c later is the 
NAPI code; I wanted to avoid the extra locking complexity in this first 
version (the fact that the interrupt status register is cleared on 
reading only makes things more complex). If you can suggest other things 
to copy, it would be good, since the copied code is less likely to be wrong.

-- 
Cesar Eduardo Barros
cesarb@cesarb.net
cesar.barros@gmail.com