From: Carsten Aulbert <carsten.aulbert@aei.mpg.de>
To: "Brandeburg, Jesse" <jesse.brandeburg@intel.com>
Cc: Bruce Allen <ballen@gravity.phys.uwm.edu>,
netdev@vger.kernel.org,
Henning Fehrmann <henning.fehrmann@aei.mpg.de>,
Bruce Allen <bruce.allen@aei.mpg.de>
Subject: Re: e1000 full-duplex TCP performance well below wire speed
Date: Thu, 31 Jan 2008 16:12:19 +0100 [thread overview]
Message-ID: <47A1E553.8010006@aei.mpg.de> (raw)
In-Reply-To: <36D9DB17C6DE9E40B059440DB8D95F52044F8BA3@orsmsx418.amr.corp.intel.com>
[-- Attachment #1: Type: text/plain, Size: 5687 bytes --]
Hi all, slowly crawling through the mails.
Brandeburg, Jesse wrote:
>>>> The test was done with various mtu sizes ranging from 1500 to 9000,
>>>> with ethernet flow control switched on and off, and using reno and
>>>> cubic as a TCP congestion control.
>>> As asked in LKML thread, please post the exact netperf command used
>>> to start the client/server, whether or not you're using irqbalanced
>>> (aka irqbalance) and what cat /proc/interrupts looks like (you ARE
>>> using MSI, right?)
We are using MSI, /proc/interrupts look like:
n0003:~# cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
0: 6536963 0 0 0 IO-APIC-edge timer
1: 2 0 0 0 IO-APIC-edge i8042
3: 1 0 0 0 IO-APIC-edge serial
8: 0 0 0 0 IO-APIC-edge rtc
9: 0 0 0 0 IO-APIC-fasteoi acpi
14: 32321 0 0 0 IO-APIC-edge libata
15: 0 0 0 0 IO-APIC-edge libata
16: 0 0 0 0 IO-APIC-fasteoi
uhci_hcd:usb5
18: 0 0 0 0 IO-APIC-fasteoi
uhci_hcd:usb4
19: 0 0 0 0 IO-APIC-fasteoi
uhci_hcd:usb3
23: 0 0 0 0 IO-APIC-fasteoi
ehci_hcd:usb1, uhci_hcd:usb2
378: 17234866 0 0 0 PCI-MSI-edge eth1
379: 129826 0 0 0 PCI-MSI-edge eth0
NMI: 0 0 0 0
LOC: 6537181 6537326 6537149 6537052
ERR: 0
(sorry for the line break).
What we don't understand is why only core0 gets the interrupts, since
the affinity is set to f:
# cat /proc/irq/378/smp_affinity
f
Right now, irqbalance is not running, though I can give it shot if
people think this will make a difference.
> I would suggest you try TCP_RR with a command line something like this:
> netperf -t TCP_RR -H <hostname> -C -c -- -b 4 -r 64K
I did that and the results can be found here:
https://n0.aei.uni-hannover.de/wiki/index.php/NetworkTest
The results with netperf running like
netperf -t TCP_STREAM -H <host> -l 20
can be found here:
https://n0.aei.uni-hannover.de/wiki/index.php/NetworkTestNetperf1
I reran the tests with
netperf -t <test> -H <host> -l 20 -c -C
or in the case of TCP_RR with the suggested burst settings -b 4 -r 64k
> Yes, InterruptThrottleRate=8000 means there will be no more than 8000
> ints/second from that adapter, and if interrupts are generated faster
> than that they are "aggregated."
>
> Interestingly since you are interested in ultra low latency, and may be
> willing to give up some cpu for it during bulk transfers you should try
> InterruptThrottleRate=1 (can generate up to 70000 ints/s)
>
On the web page you'll see that there are about 4000 interrupts/s for
most tests and up to 20,000/s for the TCP_RR test. Shall I change the
throttle rate?
>>> just for completeness can you post the dump of ethtool -e eth0 and
>>> lspci -vvv?
>> Yup, we'll give that info also.
n0002:~# ethtool -e eth1
Offset Values
------ ------
0x0000 00 30 48 93 94 2d 20 0d 46 f7 57 00 ff ff ff ff
0x0010 ff ff ff ff 6b 02 9a 10 d9 15 9a 10 86 80 df 80
0x0020 00 00 00 20 54 7e 00 00 00 10 da 00 04 00 00 27
0x0030 c9 6c 50 31 32 07 0b 04 84 29 00 00 00 c0 06 07
0x0040 08 10 00 00 04 0f ff 7f 01 4d ff ff ff ff ff ff
0x0050 14 00 1d 00 14 00 1d 00 af aa 1e 00 00 00 1d 00
0x0060 00 01 00 40 1e 12 ff ff ff ff ff ff ff ff ff ff
0x0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff cf 2f
lspci -vvv for this card:
0e:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet
Controller
Subsystem: Super Micro Computer Inc Unknown device 109a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 378
Region 0: Memory at ee200000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 5000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable+
Address: 00000000fee0f00c Data: 41b9
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM unknown,
Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number 2d-94-93-ff-ff-48-30-00
(all lspci-vvv output as attachment)
Thanks a lot, open for suggestions
Carsten
[-- Attachment #2: lspci --]
[-- Type: text/plain, Size: 16537 bytes --]
00:00.0 Host bridge: Intel Corporation E7230 Memory Controller Hub (rev c0)
Subsystem: Super Micro Computer Inc Unknown device 8580
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:01.0 PCI bridge: Intel Corporation E7230 PCI Express Root Port (rev c0) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR- NoISA+ VGA- MAbort- >Reset+ FastB2B-
Capabilities: [88] Subsystem: Super Micro Computer Inc Unknown device 8580
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4159
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 2
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
Capabilities: [140] Unknown (5)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 1
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4161
Capabilities: [90] Subsystem: Super Micro Computer Inc Unknown device 8580
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: ee100000-ee1fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 5, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4169
Capabilities: [90] Subsystem: Super Micro Computer Inc Unknown device 8580
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=0e, subordinate=0e, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: ee200000-ee2fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 6
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 6, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0f00c Data: 4171
Capabilities: [90] Subsystem: Super Micro Computer Inc Unknown device 8580
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Unknown device 8580
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 3000 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Unknown device 8580
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3020 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Unknown device 8580
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 3040 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Unknown device 8580
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 3060 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc Unknown device 8580
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=0f, subordinate=0f, sec-latency=32
I/O behind bridge: 00006000-00006fff
Memory behind bridge: ee300000-ee3fffff
Prefetchable memory behind bridge: 00000000ef000000-00000000efffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Super Micro Computer Inc Unknown device 8580
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
Subsystem: Super Micro Computer Inc Unknown device 8580
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller IDE (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Super Micro Computer Inc Unknown device 8580
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 30a0 [size=16]
Region 5: Memory at f5000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
Subsystem: Super Micro Computer Inc Unknown device 8580
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1100 [size=32]
0d:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet Controller (Copper) (rev 03)
Subsystem: Super Micro Computer Inc Unknown device 108c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 379
Region 0: Memory at ee100000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 4000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee0f00c Data: 41b1
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM unknown, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number 2c-94-93-ff-ff-48-30-00
0e:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller
Subsystem: Super Micro Computer Inc Unknown device 109a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 378
Region 0: Memory at ee200000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 5000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee0f00c Data: 41b9
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM unknown, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number 2d-94-93-ff-ff-48-30-00
0f:00.0 VGA compatible controller: XGI - Xabre Graphics Inc Volari Z7 (prog-if 00 [VGA])
Subsystem: Super Micro Computer Inc Unknown device 8580
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
BIST result: 00
Region 0: Memory at ef000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at ee300000 (32-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at 6000 [size=128]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
next prev parent reply other threads:[~2008-01-31 15:12 UTC|newest]
Thread overview: 47+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-01-30 12:23 e1000 full-duplex TCP performance well below wire speed Bruce Allen
2008-01-30 17:36 ` Brandeburg, Jesse
2008-01-30 18:45 ` Rick Jones
2008-01-30 23:15 ` Bruce Allen
2008-01-31 11:35 ` Carsten Aulbert
2008-01-31 17:55 ` Rick Jones
2008-02-01 19:57 ` Carsten Aulbert
2008-01-30 23:07 ` Bruce Allen
2008-01-31 5:43 ` Brandeburg, Jesse
2008-01-31 8:31 ` Bruce Allen
2008-01-31 18:08 ` Kok, Auke
2008-01-31 18:38 ` Rick Jones
2008-01-31 18:47 ` Kok, Auke
2008-01-31 19:07 ` Rick Jones
2008-01-31 19:13 ` Bruce Allen
2008-01-31 19:32 ` Kok, Auke
2008-01-31 19:48 ` Bruce Allen
2008-02-01 6:27 ` Bill Fink
2008-02-01 7:54 ` Bruce Allen
2008-01-31 15:12 ` Carsten Aulbert [this message]
2008-01-31 17:20 ` Brandeburg, Jesse
2008-01-31 17:27 ` Carsten Aulbert
2008-01-31 17:33 ` Brandeburg, Jesse
2008-01-31 18:11 ` running aggregate netperf TCP_RR " Rick Jones
2008-01-31 18:03 ` Rick Jones
2008-01-31 15:18 ` Carsten Aulbert
2008-01-31 9:17 ` Andi Kleen
2008-01-31 9:59 ` Bruce Allen
2008-01-31 16:09 ` Carsten Aulbert
2008-01-31 18:15 ` Kok, Auke
2008-01-30 19:17 ` Ben Greear
2008-01-30 22:33 ` Bruce Allen
[not found] <Pine.LNX.4.63.0801300324000.6391@trinity.phys.uwm.edu>
2008-01-30 13:53 ` David Miller
2008-01-30 14:01 ` Bruce Allen
2008-01-30 16:21 ` Stephen Hemminger
2008-01-30 22:25 ` Bruce Allen
2008-01-30 22:33 ` Stephen Hemminger
2008-01-30 23:23 ` Bruce Allen
2008-01-31 0:17 ` SANGTAE HA
2008-01-31 8:52 ` Bruce Allen
2008-01-31 11:45 ` Bill Fink
2008-01-31 14:50 ` David Acker
2008-01-31 15:57 ` Bruce Allen
2008-01-31 15:54 ` Bruce Allen
2008-01-31 17:36 ` Bill Fink
2008-01-31 19:37 ` Bruce Allen
2008-01-31 18:26 ` Brandeburg, Jesse
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=47A1E553.8010006@aei.mpg.de \
--to=carsten.aulbert@aei.mpg.de \
--cc=ballen@gravity.phys.uwm.edu \
--cc=bruce.allen@aei.mpg.de \
--cc=henning.fehrmann@aei.mpg.de \
--cc=jesse.brandeburg@intel.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).