RTL8169 driver no longer functioning with 8111b

netdev.vger.kernel.org archive mirror
 help / color / mirror / Atom feed

* RTL8169 driver no longer functioning with 8111b
@ 2008-05-12 23:39 ackman
  2008-05-13 20:51 ` Francois Romieu
  0 siblings, 1 reply; 7+ messages in thread
From: ackman @ 2008-05-12 23:39 UTC (permalink / raw)
  To: netdev

I've spent the better part of a day researching this to no avail.  I run 
Gentoo on an Abit AB9 PRO P965 board.  It has two onboard ports for a 
Realtek 8111B Gigabit interface.  I have been running 2.6.23-gentoo-r8 
(I think) kernel sources.  I went to reboot the unit, something I've 
done many times before, and upon reboot the two NICs were recognized but 
there was no network.  The link status for one was down (my primary port 
where the NIC cable has always been), while the other port showed a link 
status of yes.  Neither change regardless of cable now.  Also, all other 
values are pretty much *unknown*.  If I turn off the machine, the link 
status light (both on the port and my switch) is lit until the kernel 
module for r8169 is loaded, and then the link light goes off (both on 
the port and my switch).

For the life of me, I don't know what has changed short of general 
software updates in Gentoo.  I scoured the web, find suggestions about 
where Windows has turned the NIC off.  The trouble is I don't use 
Windows period on this box, no do I have the software to even test the 
theory of the power savings being turn on.  It just mysteriously has 
stopped being alive.  lspci shows the devices, their given eth0 and eth1 
as usual, I can disable them in the bios and watch Linux recognize 
they're missing, but still I can't for the life of me get them to act 
properly.  I've tried turning off ACPI, I've tried 2.6.24-gentoo-r7 
kernel, I've tried the Realtek driver source for r8168.  ACPI support 
was the only thing I can think of that has been a major change on the 
system anytime recently. 

Any suggestions would be helpful.
How might I turn off the power saving feature in the chip via linux?

-Ack

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: RTL8169 driver no longer functioning with 8111b
  2008-05-12 23:39 RTL8169 driver no longer functioning with 8111b ackman
@ 2008-05-13 20:51 ` Francois Romieu
  2008-05-13 22:29   ` Ack
  0 siblings, 1 reply; 7+ messages in thread
From: Francois Romieu @ 2008-05-13 20:51 UTC (permalink / raw)
  To: ackman; +Cc: netdev

ackman <ackman@gtf.org> :
> I've spent the better part of a day researching this to no avail.  I run 
> Gentoo on an Abit AB9 PRO P965 board.  It has two onboard ports for a 
> Realtek 8111B Gigabit interface.  I have been running 2.6.23-gentoo-r8 (I 
> think) kernel sources.

uname -a should help figuring the exact version.

[...]
> being turn on.  It just mysteriously has stopped being alive.  lspci shows 
> the devices, their given eth0 and eth1 as usual, I can disable them in the 
> bios and watch Linux recognize they're missing, but still I can't for the 
> life of me get them to act properly.  I've tried turning off ACPI, I've 
> tried 2.6.24-gentoo-r7 kernel, I've tried the Realtek driver source for 
> r8168.  ACPI support was the only thing I can think of that has been a 
> major change on the system anytime recently. 
> Any suggestions would be helpful.

Can you give noapic, pci=nomsi, pci=nommconf a try and send both
'lspci -H1 -vvxx' and 'lspci -vvxx' output ?

The 'XID' line produced by dmesg would be welcome too.

-- 
Ueimor

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: RTL8169 driver no longer functioning with 8111b
  2008-05-13 20:51 ` Francois Romieu
@ 2008-05-13 22:29   ` Ack
  2008-05-14 21:37     ` Francois Romieu
  0 siblings, 1 reply; 7+ messages in thread
From: Ack @ 2008-05-13 22:29 UTC (permalink / raw)
  To: Francois Romieu; +Cc: netdev

Sorry, I meant to say I couldn't see the box when I was typing up the 
email, it was indeed 2.6.23-gentoo-r8.

In the interest of saving your time, I managed to fix it, and I'm not 
entirely sure why, but here's what I continued to do:

I took the network cable, and connected both onboard ports to it.  This 
caused the NIC ports to turn on the orange (instead of green) light, as 
expected normally.  Otherwise, the connection light would only be green 
prior to the kernel module load from a cold boot (once the module loads, 
the link light went dead and would stay dead).  Next I connected the port 
to a 100MB switch and now the link came back up.  Plugged the cable back 
to the gigabit switch, and link stays down.  Forced the eth0 to 100MB and 
the link came back up.  Switch back to Autoneg (where ethtool had 
constantly said it was) and bang my card link stay up when disconnecting 
and reconnecting.  Honestly, I suppose I should have tried this 
previously, but I'd not had this problem on reboot any in the past, it's 
always been autoneg and ethtool was reporting as expected for that option. 
Very strange.  Thanks for wasting your time though.  Not sure what would 
need to be done for the driver for this as I'm not really sure how it got 
to the state it was in just by that reboot.

-Ack

On Tue, 13 May 2008, Francois Romieu wrote:

> ackman <ackman@gtf.org> :
>> I've spent the better part of a day researching this to no avail.  I run
>> Gentoo on an Abit AB9 PRO P965 board.  It has two onboard ports for a
>> Realtek 8111B Gigabit interface.  I have been running 2.6.23-gentoo-r8 (I
>> think) kernel sources.
>
> uname -a should help figuring the exact version.
>
> [...]
>> being turn on.  It just mysteriously has stopped being alive.  lspci shows
>> the devices, their given eth0 and eth1 as usual, I can disable them in the
>> bios and watch Linux recognize they're missing, but still I can't for the
>> life of me get them to act properly.  I've tried turning off ACPI, I've
>> tried 2.6.24-gentoo-r7 kernel, I've tried the Realtek driver source for
>> r8168.  ACPI support was the only thing I can think of that has been a
>> major change on the system anytime recently.
>> Any suggestions would be helpful.
>
> Can you give noapic, pci=nomsi, pci=nommconf a try and send both
> 'lspci -H1 -vvxx' and 'lspci -vvxx' output ?
>
> The 'XID' line produced by dmesg would be welcome too.
>
> -- 
> Ueimor
>

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: RTL8169 driver no longer functioning with 8111b
  2008-05-13 22:29   ` Ack
@ 2008-05-14 21:37     ` Francois Romieu
  2008-05-16 23:33       ` ackman
  0 siblings, 1 reply; 7+ messages in thread
From: Francois Romieu @ 2008-05-14 21:37 UTC (permalink / raw)
  To: Ack; +Cc: netdev

Ack <ackman@gtf.org> :
[...]
> I'd not had this problem on reboot any in the past, it's always been 
> autoneg and ethtool was reporting as expected for that option. Very 
> strange.  Thanks for wasting your time though.  Not sure what would need to 
> be done for the driver for this as I'm not really sure how it got to the 
> state it was in just by that reboot.

Please send the XID line and the output of lspci w/o the H1 option.

You almost surely hit a real link management bug.

-- 
Ueimor

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: RTL8169 driver no longer functioning with 8111b
  2008-05-14 21:37     ` Francois Romieu
@ 2008-05-16 23:33       ` ackman
  2008-05-20 21:08         ` Francois Romieu
  0 siblings, 1 reply; 7+ messages in thread
From: ackman @ 2008-05-16 23:33 UTC (permalink / raw)
  To: Francois Romieu; +Cc: netdev

[-- Attachment #1: Type: text/plain, Size: 609 bytes --]

Francois Romieu wrote:
> Ack <ackman@gtf.org> :
> [...]
>   
>> I'd not had this problem on reboot any in the past, it's always been 
>> autoneg and ethtool was reporting as expected for that option. Very 
>> strange.  Thanks for wasting your time though.  Not sure what would need to 
>> be done for the driver for this as I'm not really sure how it got to the 
>> state it was in just by that reboot.
>>     
>
> Please send the XID line and the output of lspci w/o the H1 option.
>
> You almost surely hit a real link management bug.
Here's the data requested.  Let me know if I can help debug this.

-Ack

[-- Attachment #2: r81xx.txt --]
[-- Type: text/plain, Size: 48201 bytes --]

dmesg: 
r8168 Gigabit Ethernet driver 8.006.00-NAPI loaded
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:03:00.0 to 64
eth0: Identified chip type is 'RTL8168B/8111B'.
eth0: RTL8168B/8111B at 0xf882a000, 00:50:8d:98:0f:de, IRQ 17
r8168 Gigabit Ethernet driver 8.006.00-NAPI loaded
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 16



I could load the kernel r8169 driver back in again later if you need me to.  I flipped back and forth during my attempts to get the link back up.  It just so happens I was running the 8168 driver from Realtek at the time I finally had some success.

 

~ # lspci -vvxx
00:00.0 Host bridge: Intel Corporation 82P965/G965 Memory Controller Hub (rev 02)
        Subsystem: ABIT Computer Corp. Unknown device 1073
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information <?>
00: 86 80 a0 29 06 00 90 20 02 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 73 10
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

00:01.0 PCI bridge: Intel Corporation 82P965/G965 PCI Express Root Port (rev 02) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 00008000-00008fff
        Memory behind bridge: fd700000-fd7fffff
        Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [88] Subsystem: Intel Corporation Unknown device 0000
        Capabilities: [80] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
                Address: 00000000  Data: 0000
        Capabilities: [a0] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #2, Speed 2.5GT/s, Width x16, ASPM L0s, Latency L0 <256ns, L1 <4us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
                        Slot # 20, PowerLimit 75.000000; Interlock- NoCompl+
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Off, PwrInd On, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet+ LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [140] Root Complex Link <?>
00: 86 80 a1 29 07 00 10 00 02 00 04 06 10 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 80 80 00 00
20: 70 fd 70 fd 01 d0 f1 df 00 00 00 00 00 00 00 00
30: 00 00 00 00 88 00 00 00 00 00 00 00 0b 01 08 00

00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Contoller #4 (rev 02) (prog-if 00 [UHCI])
        Subsystem: ABIT Computer Corp. Unknown device 1073
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 4: I/O ports at ff00 [size=32]
        Kernel driver in use: uhci_hcd
00: 86 80 34 28 05 00 80 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 ff 00 00 00 00 00 00 00 00 00 00 7b 14 73 10
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00

00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02) (prog-if 00 [UHCI])
        Subsystem: ABIT Computer Corp. Unknown device 1073
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 21
        Region 4: I/O ports at fe00 [size=32]
        Kernel driver in use: uhci_hcd
00: 86 80 35 28 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 fe 00 00 00 00 00 00 00 00 00 00 7b 14 73 10
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 00 00

00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02) (prog-if 20 [EHCI])
        Subsystem: ABIT Computer Corp. Unknown device 1073
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin C routed to IRQ 17
        Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ehci_hcd
00: 86 80 3a 28 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 f0 ff fd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 73 10
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 03 00 00

00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 22
        Region 0: Memory at fdff4000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [130] Root Complex Link <?>
        Kernel driver in use: HDA Intel
        Kernel modules: snd-hda-intel
00: 86 80 4b 28 06 00 10 00 02 00 03 04 10 00 00 00
10: 04 40 ff fd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00

00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        I/O behind bridge: 00007000-00007fff
        Memory behind bridge: fd400000-fd4fffff
        Prefetchable memory behind bridge: 00000000fd300000-00000000fd3fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
                        ClockPM- Suprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled+ Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
                        Slot # 10, PowerLimit 10.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
                        Changed: MRL- PresDet- LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
                Address: 00000000  Data: 0000
        Capabilities: [90] Subsystem: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [180] Root Complex Link <?>
00: 86 80 3f 28 07 00 10 00 02 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 70 70 00 00
20: 40 fd 40 fd 31 fd 31 fd 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00

00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 (rev 02) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
        I/O behind bridge: 0000d000-0000dfff
        Memory behind bridge: fd200000-fd2fffff
        Prefetchable memory behind bridge: 00000000fde00000-00000000fdefffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
                        ClockPM- Suprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
                        Slot # 12, PowerLimit 10.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet+ LinkState+
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
                Address: 00000000  Data: 0000
        Capabilities: [90] Subsystem: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [180] Root Complex Link <?>
00: 86 80 43 28 07 00 10 00 02 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 03 03 00 d0 d0 00 00
20: 20 fd 20 fd e1 fd e1 fd 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 05 03 00 00

00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
        I/O behind bridge: 0000b000-0000bfff
        Memory behind bridge: fdd00000-fddfffff
        Prefetchable memory behind bridge: 00000000fdc00000-00000000fdcfffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
                        ClockPM- Suprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
                        Slot # 13, PowerLimit 10.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet+ LinkState+
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
                Address: 00000000  Data: 0000
        Capabilities: [90] Subsystem: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [180] Root Complex Link <?>
00: 86 80 45 28 07 00 10 00 02 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 04 04 00 b0 b0 00 00
20: d0 fd d0 fd c1 fd c1 fd 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 04 00 00

00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
        I/O behind bridge: 0000a000-0000afff
        Memory behind bridge: fdb00000-fdbfffff
        Prefetchable memory behind bridge: 00000000fda00000-00000000fdafffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
                        ClockPM- Suprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
                        Slot # 14, PowerLimit 10.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet+ LinkState+
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
                Address: 00000000  Data: 0000
        Capabilities: [90] Subsystem: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [180] Root Complex Link <?>
00: 86 80 47 28 07 00 10 00 02 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 05 05 00 a0 a0 00 00
20: b0 fd b0 fd a1 fd a1 fd 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00

00:1c.5 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 6 (rev 02) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
        I/O behind bridge: 00009000-00009fff
        Memory behind bridge: fd900000-fd9fffff
        Prefetchable memory behind bridge: 00000000fd800000-00000000fd8fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                        ExtTag- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
                LnkCap: Port #6, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
                        ClockPM- Suprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
                        Slot # 15, PowerLimit 10.000000; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                        Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                        Changed: MRL- PresDet+ LinkState+
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
                Address: 00000000  Data: 0000
        Capabilities: [90] Subsystem: Intel Corporation 82801H (ICH8 Family) PCI Express Port 6
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100] Virtual Channel <?>
        Capabilities: [180] Root Complex Link <?>
00: 86 80 49 28 07 00 10 00 02 00 04 06 10 00 81 00
10: 00 00 00 00 00 00 00 00 00 06 06 00 90 90 00 00
20: 90 fd 90 fd 81 fd 81 fd 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 02 00 00

00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
        Subsystem: ABIT Computer Corp. Unknown device 1073
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 20
        Region 4: I/O ports at fd00 [size=32]
        Kernel driver in use: uhci_hcd
00: 86 80 30 28 05 00 80 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 fd 00 00 00 00 00 00 00 00 00 00 7b 14 73 10
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 01 00 00

00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
        Subsystem: ABIT Computer Corp. Unknown device 1073
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 18
        Region 4: I/O ports at fc00 [size=32]
        Kernel driver in use: uhci_hcd
00: 86 80 31 28 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 fc 00 00 00 00 00 00 00 00 00 00 7b 14 73 10
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 00 00

00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
        Subsystem: ABIT Computer Corp. Unknown device 1073
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin C routed to IRQ 17
        Region 4: I/O ports at fb00 [size=32]
        Kernel driver in use: uhci_hcd
00: 86 80 32 28 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 fb 00 00 00 00 00 00 00 00 00 00 7b 14 73 10
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 03 00 00

00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02) (prog-if 20 [EHCI])
        Subsystem: ABIT Computer Corp. Unknown device 1073
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 20
        Region 0: Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ehci_hcd
00: 86 80 36 28 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 e0 ff fd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 73 10
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2) (prog-if 01 [Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
        I/O behind bridge: 0000c000-0000cfff
        Memory behind bridge: fd600000-fd6fffff
        Prefetchable memory behind bridge: 00000000fd500000-00000000fd5fffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [50] Subsystem: Intel Corporation 82801 PCI Bridge
00: 86 80 4e 24 07 00 10 00 f2 01 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 07 07 20 c0 c0 80 22
20: 60 fd 60 fd 51 fd 51 fd 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00

00:1f.0 ISA bridge: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller (rev 02)
        Subsystem: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information <?>
00: 86 80 10 28 07 01 10 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 10 28
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

00:1f.2 SATA controller: Intel Corporation 82801HR/HO/HH (ICH8R/DO/DH) 6 port SATA AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
        Subsystem: ABIT Computer Corp. Unknown device 1073
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 223
        Region 0: I/O ports at fa00 [size=8]
        Region 1: I/O ports at f900 [size=4]
        Region 2: I/O ports at f800 [size=8]
        Region 3: I/O ports at f700 [size=4]
        Region 4: I/O ports at f600 [size=32]
        Region 5: Memory at fdffd000 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/4 Enable+
                Address: fee0300c  Data: 41c9
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [a8] SATA HBA <?>
        Kernel driver in use: ahci
00: 86 80 21 28 07 04 b0 02 02 01 06 01 00 00 00 00
10: 01 fa 00 00 01 f9 00 00 01 f8 00 00 01 f7 00 00
20: 01 f6 00 00 00 d0 ff fd 00 00 00 00 7b 14 73 10
30: 00 00 00 00 80 00 00 00 00 00 00 00 0b 02 00 00

00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
        Subsystem: Intel Corporation 82801H (ICH8 Family) SMBus Controller
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin B routed to IRQ 18
        Region 0: Memory at fdffc000 (32-bit, non-prefetchable) [size=256]
        Region 4: I/O ports at 0500 [size=32]
        Kernel driver in use: i801_smbus
        Kernel modules: i2c-i801
00: 86 80 3e 28 03 00 80 02 02 00 05 0c 00 00 00 00
10: 00 c0 ff fd 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 05 00 00 00 00 00 00 00 00 00 00 86 80 3e 28
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 00 00

01:00.0 VGA compatible controller: ATI Technologies Inc R480 [Radeon X800 GTO (PCIE)] (prog-if 00 [VGA controller])
        Subsystem: ASUSTeK Computer Inc. Unknown device 0074
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
        Region 2: Memory at fd7f0000 (64-bit, non-prefetchable) [size=64K]
        Region 4: I/O ports at 8e00 [size=256]
        [virtual] Expansion ROM at fd700000 [disabled] [size=128K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns, L1 <4us
                        ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <256ns, L1 <2us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [100] Advanced Error Reporting <?>
00: 02 10 4f 5d 07 00 10 00 00 00 00 03 10 00 80 00
10: 0c 00 00 d0 00 00 00 00 04 00 7f fd 00 00 00 00
20: 01 8e 00 00 00 00 00 00 00 00 00 00 43 10 74 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00

01:00.1 Display controller: ATI Technologies Inc R480 [Radeon X800 GTO (PCIE)] (Secondary)
        Subsystem: ASUSTeK Computer Inc. Unknown device 0075
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Region 0: Memory at fd7e0000 (64-bit, non-prefetchable) [size=64K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns, L1 <4us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <256ns, L1 <2us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
00: 02 10 6f 5d 06 00 10 00 00 00 80 03 10 00 00 00
10: 04 00 7e fd 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 75 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00

03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
        Subsystem: ABIT Computer Corp. Unknown device 1073
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 17
        Region 0: I/O ports at de00 [size=256]
        Region 2: Memory at fd2ff000 (64-bit, non-prefetchable) [size=4K]
        [virtual] Expansion ROM at fde00000 [disabled] [size=128K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME+
        Capabilities: [48] Vital Product Data <?>
        Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [60] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited
                        ExtTag+ AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 4096 bytes
                DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Capabilities: [84] Vendor Specific Information <?>
        Capabilities: [100] Advanced Error Reporting <?>
        Capabilities: [12c] Virtual Channel <?>
        Capabilities: [148] Device Serial Number 68-81-ec-10-00-00-00-00
        Capabilities: [154] Power Budgeting <?>
        Kernel driver in use: r8168
        Kernel modules: r8169, r8168
00: ec 10 68 81 07 00 10 00 01 00 00 02 10 00 00 00
10: 01 de 00 00 00 00 00 00 04 f0 2f fd 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 73 10
30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 00 00

04:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01)
        Subsystem: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at fddff000 (64-bit, non-prefetchable) [size=128]
        Region 2: Memory at fddf8000 (64-bit, non-prefetchable) [size=16K]
        Region 4: I/O ports at bf00 [size=128]
        [virtual] Expansion ROM at fdc00000 [disabled] [size=512K]
        Capabilities: [54] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
                DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Capabilities: [100] Advanced Error Reporting <?>
        Kernel driver in use: sata_sil24
00: 95 10 32 31 07 00 10 00 01 00 80 01 10 00 00 00
10: 04 f0 df fd 00 00 00 00 04 80 df fd 00 00 00 00
20: 01 bf 00 00 00 00 00 00 00 00 00 00 95 10 32 31
30: 00 00 00 00 54 00 00 00 00 00 00 00 0b 01 00 00

05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
        Subsystem: ABIT Computer Corp. Unknown device 1073
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: I/O ports at ae00 [size=256]
        Region 2: Memory at fdbff000 (64-bit, non-prefetchable) [size=4K]
        [virtual] Expansion ROM at fda00000 [disabled] [size=128K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [48] Vital Product Data <?>
        Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [60] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <1us, L1 unlimited
                        ExtTag+ AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Capabilities: [84] Vendor Specific Information <?>
        Capabilities: [100] Advanced Error Reporting <?>
        Capabilities: [12c] Virtual Channel <?>
        Capabilities: [148] Device Serial Number 68-81-ec-10-00-00-00-01
        Capabilities: [154] Power Budgeting <?>
        Kernel driver in use: r8168
        Kernel modules: r8169, r8168
00: ec 10 68 81 07 00 10 00 01 00 00 02 10 00 00 00
10: 01 ae 00 00 00 00 00 00 04 f0 bf fd 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 73 10
30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00

06:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
        Subsystem: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 19
        Region 5: Memory at fd9fe000 (32-bit, non-prefetchable) [size=8K]
        [virtual] Expansion ROM at fd800000 [disabled] [size=64K]
        Capabilities: [68] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] Express (v1) Legacy Endpoint, MSI 01
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
                LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <1us, L1 <16us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Kernel driver in use: ahci
00: 7b 19 63 23 07 00 10 00 02 01 06 01 10 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 e0 9f fd 00 00 00 00 7b 19 63 23
30: 00 00 00 00 68 00 00 00 00 00 00 00 0a 01 00 00

06:00.1 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 02) (prog-if 85 [Master SecO PriO])
        Subsystem: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin B routed to IRQ 0
        Region 0: I/O ports at 9f00 [disabled] [size=8]
        Region 1: I/O ports at 9e00 [disabled] [size=4]
        Region 2: I/O ports at 9d00 [disabled] [size=8]
        Region 3: I/O ports at 9c00 [disabled] [size=4]
        Region 4: I/O ports at 9b00 [disabled] [size=16]
        Capabilities: [68] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 7b 19 63 23 00 00 10 00 02 85 01 01 00 00 00 00
10: 01 9f 00 00 01 9e 00 00 01 9d 00 00 01 9c 00 00
20: 01 9b 00 00 00 00 00 00 00 00 00 00 7b 19 63 23
30: 00 00 00 00 68 00 00 00 00 00 00 00 00 02 00 00

07:02.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
        Subsystem: ABIT Computer Corp. Unknown device 1073
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at fd6ff000 (32-bit, non-prefetchable) [size=2K]
        Region 1: Memory at fd6f8000 (32-bit, non-prefetchable) [size=16K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME+
        Kernel driver in use: firewire_ohci
        Kernel modules: ohci1394, firewire-ohci
00: 4c 10 23 80 06 00 10 02 00 10 00 0c 10 40 00 00
10: 00 f0 6f fd 00 80 6f fd 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 7b 14 73 10
30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 01 02 04

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: RTL8169 driver no longer functioning with 8111b
  2008-05-16 23:33       ` ackman
@ 2008-05-20 21:08         ` Francois Romieu
  2008-05-24  3:39           ` ackman
  0 siblings, 1 reply; 7+ messages in thread
From: Francois Romieu @ 2008-05-20 21:08 UTC (permalink / raw)
  To: ackman; +Cc: netdev

ackman <ackman@gtf.org> :
[...]
> I could load the kernel r8169 driver back in again later if you need me to.

Please do. It gives a specific footprint of the device (the 'XID' line)
whereas Realtek's driver does not tell exactly which kind of 8168b was
detected.

-- 
Ueimor

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: RTL8169 driver no longer functioning with 8111b
  2008-05-20 21:08         ` Francois Romieu
@ 2008-05-24  3:39           ` ackman
  0 siblings, 0 replies; 7+ messages in thread
From: ackman @ 2008-05-24  3:39 UTC (permalink / raw)
  To: Francois Romieu; +Cc: netdev

Francois Romieu wrote:
> ackman <ackman@gtf.org> :
> [...]
>   
>> I could load the kernel r8169 driver back in again later if you need me to.
>>     
>
> Please do. It gives a specific footprint of the device (the 'XID' line)
> whereas Realtek's driver does not tell exactly which kind of 8168b was
> detected.
>
>   
I will do so this coming Monday.  Apologies for the delay.

-Ack


^ permalink raw reply	[flat|nested] 7+ messages in thread

end of thread, other threads:[~2008-05-24  3:39 UTC | newest]

Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2008-05-12 23:39 RTL8169 driver no longer functioning with 8111b ackman
2008-05-13 20:51 ` Francois Romieu
2008-05-13 22:29   ` Ack
2008-05-14 21:37     ` Francois Romieu
2008-05-16 23:33       ` ackman
2008-05-20 21:08         ` Francois Romieu
2008-05-24  3:39           ` ackman

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).