[PATCH 0/8][RFC] qlge: New Qlogic 10Gb Ethernet Driver for 2.6.28

[PATCH 0/8][RFC] qlge: New Qlogic 10Gb Ethernet Driver for 2.6.28

[Ron Mercer]

Jeff,

The following patches are for further RFC for the Qlogic 10Gb driver.

This series does some more cleanup but mostly consistes of the recieve buffer alignment copy per Dave Miller.

1)  Align inbound ethernet header on 2-byte boundary.
2)  Fix set_ethtool_ops call.
3)  More cleanup per checkpatch.pl.
4)  Version change to v1.00.00-b3

Next additions:
Implement ethtool_op_getlink()
Implement flash


Regards,
Ron Mercer
Qlogic Corporation

[PATCH 1/8] [RFC] qlge: Add license file LICENSE.qlge.

[Ron Mercer]

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
---
 Documentation/networking/LICENSE.qlge |   46 +++++++++++++++++++++++++++++++++
 1 files changed, 46 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/networking/LICENSE.qlge

diff --git a/Documentation/networking/LICENSE.qlge b/Documentation/networking/LICENSE.qlge
new file mode 100644
index 0000000..123b6ed
--- /dev/null
+++ b/Documentation/networking/LICENSE.qlge
@@ -0,0 +1,46 @@
+Copyright (c)  2003-2008 QLogic Corporation
+QLogic Linux Networking HBA Driver
+
+This program includes a device driver for Linux 2.6 that may be
+distributed with QLogic hardware specific firmware binary file.
+You may modify and redistribute the device driver code under the
+GNU General Public License as published by the Free Software
+Foundation (version 2 or a later version).
+
+You may redistribute the hardware specific firmware binary file
+under the following terms:
+
+	1. Redistribution of source code (only if applicable),
+	   must retain the above copyright notice, this list of
+	   conditions and the following disclaimer.
+
+	2. Redistribution in binary form must reproduce the above
+	   copyright notice, this list of conditions and the
+	   following disclaimer in the documentation and/or other
+	   materials provided with the distribution.
+
+	3. The name of QLogic Corporation may not be used to
+	   endorse or promote products derived from this software
+	   without specific prior written permission
+
+REGARDLESS OF WHAT LICENSING MECHANISM IS USED OR APPLICABLE,
+THIS PROGRAM IS PROVIDED BY QLOGIC CORPORATION "AS IS'' AND ANY
+EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
+PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR
+BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
+EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
+TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
+OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+POSSIBILITY OF SUCH DAMAGE.
+
+USER ACKNOWLEDGES AND AGREES THAT USE OF THIS PROGRAM WILL NOT
+CREATE OR GIVE GROUNDS FOR A LICENSE BY IMPLICATION, ESTOPPEL, OR
+OTHERWISE IN ANY INTELLECTUAL PROPERTY RIGHTS (PATENT, COPYRIGHT,
+TRADE SECRET, MASK WORK, OR OTHER PROPRIETARY RIGHT) EMBODIED IN
+ANY OTHER QLOGIC HARDWARE OR SOFTWARE EITHER SOLELY OR IN
+COMBINATION WITH THIS PROGRAM.
+
-- 
1.5.0.rc4.16.g9e258

[PATCH 2/8] [RFC] qlge: Additions to driver/net/Makefile and Kconfig.

[Ron Mercer]

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
---
 drivers/net/Kconfig  |    9 +++++++++
 drivers/net/Makefile |    1 +
 2 files changed, 10 insertions(+), 0 deletions(-)

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 4a11296..a3c7b20 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -2496,6 +2496,15 @@ config BNX2X
 	  To compile this driver as a module, choose M here: the module
 	  will be called bnx2x.  This is recommended.
 
+config QLGE
+	tristate "QLogic QLGE 10Gb Ethernet Driver Support"
+	depends on PCI
+	help
+	  This driver supports QLogic ISP8XXX 10Gb Ethernet cards.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called qlge.
+
 source "drivers/net/sfc/Kconfig"
 
 endif # NETDEV_10000
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 7629c90..f5f3b16 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -128,6 +128,7 @@ obj-$(CONFIG_AX88796) += ax88796.o
 obj-$(CONFIG_TSI108_ETH) += tsi108_eth.o
 obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o
 obj-$(CONFIG_QLA3XXX) += qla3xxx.o
+obj-$(CONFIG_QLGE) += qlge/
 
 obj-$(CONFIG_PPP) += ppp_generic.o
 obj-$(CONFIG_PPP_ASYNC) += ppp_async.o
-- 
1.5.0.rc4.16.g9e258

[PATCH 3/8] [RFC] qlge: Added drivers/net/qlge/Makefile.

[Ron Mercer]

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
---
 drivers/net/qlge/Makefile |    7 +++++++
 1 files changed, 7 insertions(+), 0 deletions(-)
 create mode 100644 drivers/net/qlge/Makefile

diff --git a/drivers/net/qlge/Makefile b/drivers/net/qlge/Makefile
new file mode 100644
index 0000000..8a19765
--- /dev/null
+++ b/drivers/net/qlge/Makefile
@@ -0,0 +1,7 @@
+#
+# Makefile for the Qlogic 10GbE PCI Express ethernet driver
+#
+
+obj-$(CONFIG_QLGE) += qlge.o
+
+qlge-objs := qlge_main.o qlge_dbg.o qlge_mpi.o qlge_ethtool.o
-- 
1.5.0.rc4.16.g9e258

[PATCH 4/8] [RFC] qlge: Add main header file qlge.h

[Ron Mercer]

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
---
 drivers/net/qlge/qlge.h | 1589 +++++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 1589 insertions(+), 0 deletions(-)
 create mode 100755 drivers/net/qlge/qlge.h

diff --git a/drivers/net/qlge/qlge.h b/drivers/net/qlge/qlge.h
new file mode 100755
index 0000000..6efb899
--- /dev/null
+++ b/drivers/net/qlge/qlge.h
@@ -0,0 +1,1589 @@
+/*
+ * QLogic QLA41xx NIC HBA Driver
+ * Copyright (c)  2003-2006 QLogic Corporation
+ *
+ * See LICENSE.qlge for copyright and licensing details.
+ */
+#ifndef _QLGE_H_
+#define _QLGE_H_
+
+#include <linux/pci.h>
+#include <linux/netdevice.h>
+
+/*
+ * General definitions...
+ */
+#define DRV_NAME  	"qlge"
+#define DRV_STRING 	"QLogic 10 Gigabit PCI-E Ethernet Driver "
+#define DRV_VERSION	"v1.00.00-b3"
+
+#define PFX "qlge: "
+#define QPRINTK(qdev, nlevel, klevel, fmt, args...)     \
+       do {       \
+	if (!((qdev)->msg_enable & NETIF_MSG_##nlevel))		\
+		;						\
+	else							\
+		dev_printk(KERN_##klevel, &((qdev)->pdev->dev),	\
+			   "%s: " fmt, __func__, ##args);  \
+       } while (0)
+
+/* #define QLGE_FAST_TXQ */
+#define PALLADIUM
+
+#define QLGE_VENDOR_ID    0x1077
+#define QLGE_DEVICE_ID1    0x8012
+#define QLGE_DEVICE_ID   0x8000
+
+#define MAX_RX_RINGS 128
+#define MAX_TX_RINGS 128
+
+#define NUM_TX_RING_ENTRIES	256
+#define NUM_RX_RING_ENTRIES	256
+
+#define NUM_SMALL_BUFFERS   512
+#define NUM_LARGE_BUFFERS   512
+
+#define SMALL_BUFFER_SIZE 256
+#define LARGE_BUFFER_SIZE	PAGE_SIZE
+#define MAX_SPLIT_SIZE 1023
+#define QLGE_SB_PAD 32
+
+#ifdef PALLADIUM
+/* Palladium workaround start:
+ * P1 doesn't like coalescing.  It causes
+ * bogus interrupts.
+ */
+#define DFLT_COALESCE_WAIT 0
+#define MAX_INTER_FRAME_WAIT 0
+#define DFLT_INTER_FRAME_WAIT 0
+/* Palladium workaround end: */
+#else
+#define DFLT_COALESCE_WAIT 100	/* 100 usec wait for coalescing */
+#define MAX_INTER_FRAME_WAIT 10	/* 10 usec max interframe-wait for coalescing */
+#define DFLT_INTER_FRAME_WAIT (MAX_INTER_FRAME_WAIT/2)
+#endif
+
+#define MSLEEP_COUNT 50
+#define MSLEEP_DELAY 500
+
+#define TX_DESC_PER_IOCB 8
+/* The maximum number of frags we handle is based
+ * on PAGE_SIZE...
+ */
+#if (PAGE_SHIFT == 12) || (PAGE_SHIFT == 13)	/* 4k & 8k pages */
+#define TX_DESC_PER_OAL ((MAX_SKB_FRAGS - TX_DESC_PER_IOCB) + 2)
+#elif (PAGE_SHIFT == 16)	/* 64k pages */
+#define TX_DESC_PER_OAL 0
+#endif
+
+#define DB_PAGE_SIZE 4096
+
+/*
+ * REGISTER AND BIT DEFINITIONS.
+ */
+enum {
+	ADDR_RDY = (1 << 31),
+	ADDR_R = (1 << 30),
+	ADDR_ERR = (1 << 29),
+};
+/*
+ * Processor Address Register (PROC_ADDR) bit definitions.
+ */
+enum {
+
+	/* Misc. stuff */
+	MAILBOX_COUNT = 16,
+
+	PROC_ADDR_ERR = ADDR_ERR,
+	PROC_ADDR_R = ADDR_R,
+	PROC_ADDR_RDY = ADDR_RDY,
+	PROC_ADDR_DA = (1 << 28),
+	PROC_ADDR_FUNC0_MBI = 0x00001180,
+	PROC_ADDR_FUNC0_MBO = (PROC_ADDR_FUNC0_MBI + MAILBOX_COUNT),
+	PROC_ADDR_FUNC0_CTL = 0x000011a1,
+	PROC_ADDR_FUNC2_MBI = 0x00001280,
+	PROC_ADDR_FUNC2_MBO = (PROC_ADDR_FUNC2_MBI + MAILBOX_COUNT),
+	PROC_ADDR_FUNC2_CTL = 0x000012a1,
+	PROC_ADDR_MPI_RISC = 0x00000000,
+	PROC_ADDR_MDE = 0x00010000,
+	PROC_ADDR_REGBLOCK = 0x00020000,
+	PROC_ADDR_RISC_REG = 0x00030000,
+};
+
+/*
+ * System Register (SYS) bit definitions.
+ */
+enum {
+	SYS_EFE = (1 << 0),
+	SYS_FAE = (1 << 1),
+	SYS_MDC = (1 << 2),
+	SYS_DST = (1 << 3),
+	SYS_DWC = (1 << 4),
+	SYS_EVW = (1 << 5),
+	SYS_OMP_DLY_MASK = 0x3f000000,
+	/*
+	 * There are no values defined as of edit #15.
+	 */
+	SYS_ODI = (1 << 14),
+};
+
+/*
+ *  Reset/Failover Register (RST_FO) bit definitions.
+ */
+enum {
+	RST_FO_TFO = (1 << 0),
+	RST_FO_RR_MASK = 0x00060000,
+	RST_FO_RR_CQ_CAM = 0x00000000,
+	RST_FO_RR_DROP = 0x00000001,
+	RST_FO_RR_DQ = 0x00000002,
+	RST_FO_RR_RCV_FUNC_CQ = 0x00000003,
+	RST_FO_FRB = (1 << 12),
+	RST_FO_MOP = (1 << 13),
+	RST_FO_REG = (1 << 14),
+	RST_FO_FR = (1 << 15),
+};
+
+/*
+ * Function Specific Control Register (FSC) bit definitions.
+ */
+enum {
+	FSC_DBRST_MASK = 0x00070000,
+	FSC_DBRST_256 = 0x00000000,
+	FSC_DBRST_512 = 0x00000001,
+	FSC_DBRST_768 = 0x00000002,
+	FSC_DBRST_1024 = 0x00000003,
+	FSC_DBL_MASK = 0x00180000,
+	FSC_DBL_DBRST = 0x00000000,
+	FSC_DBL_MAX_PLD = 0x00000008,
+	FSC_DBL_MAX_BRST = 0x00000010,
+	FSC_DBL_128_BYTES = 0x00000018,
+	FSC_EC = (1 << 5),
+	FSC_EPC_MASK = 0x00c00000,
+	FSC_EPC_INBOUND = (1 << 6),
+	FSC_EPC_OUTBOUND = (1 << 7),
+	FSC_VM_PAGESIZE_MASK = 0x07000000,
+	FSC_VM_PAGE_2K = 0x00000100,
+	FSC_VM_PAGE_4K = 0x00000200,
+	FSC_VM_PAGE_8K = 0x00000300,
+	FSC_VM_PAGE_64K = 0x00000600,
+	FSC_SH = (1 << 11),
+	FSC_DSB = (1 << 12),
+	FSC_STE = (1 << 13),
+	FSC_FE = (1 << 15),
+};
+
+/*
+ *  Host Command Status Register (CSR) bit definitions.
+ */
+enum {
+	CSR_ERR_STS_MASK = 0x0000003f,
+	/*
+	 * There are no valued defined as of edit #15.
+	 */
+	CSR_RR = (1 << 8),
+	CSR_HRI = (1 << 9),
+	CSR_RP = (1 << 10),
+	CSR_CMD_PARM_SHIFT = 22,
+	CSR_CMD_NOP = 0x00000000,
+	CSR_CMD_SET_RST = 0x1000000,
+	CSR_CMD_CLR_RST = 0x20000000,
+	CSR_CMD_SET_PAUSE = 0x30000000,
+	CSR_CMD_CLR_PAUSE = 0x40000000,
+	CSR_CMD_SET_H2R_INT = 0x50000000,
+	CSR_CMD_CLR_H2R_INT = 0x60000000,
+	CSR_CMD_PAR_EN = 0x70000000,
+	CSR_CMD_SET_BAD_PAR = 0x80000000,
+	CSR_CMD_CLR_BAD_PAR = 0x90000000,
+	CSR_CMD_CLR_R2PCI_INT = 0xa0000000,
+};
+
+/*
+ *  Configuration Register (CFG) bit definitions.
+ */
+enum {
+	CFG_LRQ = (1 << 0),
+	CFG_DRQ = (1 << 1),
+	CFG_LR = (1 << 2),
+	CFG_DR = (1 << 3),
+	CFG_LE = (1 << 5),
+	CFG_LCQ = (1 << 6),
+	CFG_DCQ = (1 << 7),
+	CFG_Q_SHIFT = 8,
+	CFG_Q_MASK = 0x7f000000,
+};
+
+/*
+ *  Status Register (STS) bit definitions.
+ */
+enum {
+	STS_FE = (1 << 0),
+	STS_PI = (1 << 1),
+	STS_PL0 = (1 << 2),
+	STS_PL1 = (1 << 3),
+	STS_PI0 = (1 << 4),
+	STS_PI1 = (1 << 5),
+	STS_FUNC_ID_MASK = 0x000000c0,
+	STS_FUNC_ID_SHIFT = 6,
+	STS_F0E = (1 << 8),
+	STS_F1E = (1 << 9),
+	STS_F2E = (1 << 10),
+	STS_F3E = (1 << 11),
+	STS_NFE = (1 << 12),
+};
+
+/*
+ * Interrupt Enable Register (INTR_EN) bit definitions.
+ */
+enum {
+	INTR_EN_INTR_MASK = 0x007f0000,
+	INTR_EN_TYPE_MASK = 0x03000000,
+	INTR_EN_TYPE_ENABLE = 0x00000100,
+	INTR_EN_TYPE_DISABLE = 0x00000200,
+	INTR_EN_TYPE_READ = 0x00000300,
+	INTR_EN_IHD = (1 << 13),
+	INTR_EN_IHD_MASK = (INTR_EN_IHD << 16),
+	INTR_EN_EI = (1 << 14),
+	INTR_EN_EN = (1 << 15),
+};
+
+/*
+ * Interrupt Mask Register (INTR_MASK) bit definitions.
+ */
+enum {
+	INTR_MASK_PI = (1 << 0),
+	INTR_MASK_HL0 = (1 << 1),
+	INTR_MASK_LH0 = (1 << 2),
+	INTR_MASK_HL1 = (1 << 3),
+	INTR_MASK_LH1 = (1 << 4),
+	INTR_MASK_SE = (1 << 5),
+	INTR_MASK_LSC = (1 << 6),
+	INTR_MASK_MC = (1 << 7),
+	INTR_MASK_LINK_IRQS = INTR_MASK_LSC | INTR_MASK_SE | INTR_MASK_MC,
+};
+
+/*
+ *  Register (REV_ID) bit definitions.
+ */
+enum {
+	REV_ID_MASK = 0x0000000f,
+	REV_ID_NICROLL_SHIFT = 0,
+	REV_ID_NICREV_SHIFT = 4,
+	REV_ID_XGROLL_SHIFT = 8,
+	REV_ID_XGREV_SHIFT = 12,
+	REV_ID_CHIPREV_SHIFT = 28,
+};
+
+/*
+ *  Force ECC Error Register (FRC_ECC_ERR) bit definitions.
+ */
+enum {
+	FRC_ECC_ERR_VW = (1 << 12),
+	FRC_ECC_ERR_VB = (1 << 13),
+	FRC_ECC_ERR_NI = (1 << 14),
+	FRC_ECC_ERR_NO = (1 << 15),
+	FRC_ECC_PFE_SHIFT = 16,
+	FRC_ECC_ERR_DO = (1 << 18),
+	FRC_ECC_P14 = (1 << 19),
+};
+
+/*
+ *  Error Status Register (ERR_STS) bit definitions.
+ */
+enum {
+	ERR_STS_NOF = (1 << 0),
+	ERR_STS_NIF = (1 << 1),
+	ERR_STS_DRP = (1 << 2),
+	ERR_STS_XGP = (1 << 3),
+	ERR_STS_FOU = (1 << 4),
+	ERR_STS_FOC = (1 << 5),
+	ERR_STS_FOF = (1 << 6),
+	ERR_STS_FIU = (1 << 7),
+	ERR_STS_FIC = (1 << 8),
+	ERR_STS_FIF = (1 << 9),
+	ERR_STS_MOF = (1 << 10),
+	ERR_STS_TA = (1 << 11),
+	ERR_STS_MA = (1 << 12),
+	ERR_STS_MPE = (1 << 13),
+	ERR_STS_SCE = (1 << 14),
+	ERR_STS_STE = (1 << 15),
+	ERR_STS_FOW = (1 << 16),
+	ERR_STS_UE = (1 << 17),
+	ERR_STS_MCH = (1 << 26),
+	ERR_STS_LOC_SHIFT = 27,
+};
+
+/*
+ *  RAM Debug Address Register (RAM_DBG_ADDR) bit definitions.
+ */
+enum {
+	RAM_DBG_ADDR_FW = (1 << 30),
+	RAM_DBG_ADDR_FR = (1 << 31),
+};
+
+/*
+ * Semaphore Register (SEM) bit definitions.
+ */
+enum {
+	/*
+	 * Example:
+	 * reg = SEM_XGMAC0_MASK | (SEM_SET << SEM_XGMAC0_SHIFT)
+	 */
+	SEM_CLEAR = 0,
+	SEM_SET = 1,
+	SEM_FORCE = 3,
+	SEM_XGMAC0_SHIFT = 0,
+	SEM_XGMAC1_SHIFT = 2,
+	SEM_ICB_SHIFT = 4,
+	SEM_MAC_ADDR_SHIFT = 6,
+	SEM_FLASH_SHIFT = 8,
+	SEM_PROBE_SHIFT = 10,
+	SEM_RT_IDX_SHIFT = 12,
+	SEM_PROC_REG_SHIFT = 14,
+	SEM_XGMAC0_MASK = 0x00030000,
+	SEM_XGMAC1_MASK = 0x000c0000,
+	SEM_ICB_MASK = 0x00300000,
+	SEM_MAC_ADDR_MASK = 0x00c00000,
+	SEM_FLASH_MASK = 0x03000000,
+	SEM_PROBE_MASK = 0x0c000000,
+	SEM_RT_IDX_MASK = 0x30000000,
+	SEM_PROC_REG_MASK = 0xc0000000,
+};
+
+/*
+ *  10G MAC Address  Register (XGMAC_ADDR) bit definitions.
+ */
+enum {
+	XGMAC_ADDR_RDY = ADDR_RDY,
+	XGMAC_ADDR_R = ADDR_R,
+	XGMAC_ADDR_XME = ADDR_ERR,
+
+	/* XGMAC control registers */
+	PAUSE_SRC_LO = 0x00000100,
+	PAUSE_SRC_HI = 0x00000104,
+	GLOBAL_CFG = 0x00000108,
+	GLOBAL_CFG_RESET = (1 << 0),
+	GLOBAL_CFG_JUMBO = (1 << 6),
+	GLOBAL_CFG_TX_STAT_EN = (1 << 10),
+	GLOBAL_CFG_RX_STAT_EN = (1 << 11),
+	TX_CFG = 0x0000010c,
+	TX_CFG_RESET = (1 << 0),
+	TX_CFG_EN = (1 << 1),
+	TX_CFG_PREAM = (1 << 2),
+	RX_CFG = 0x00000110,
+	RX_CFG_RESET = (1 << 0),
+	RX_CFG_EN = (1 << 1),
+	RX_CFG_PREAM = (1 << 2),
+	FLOW_CTL = 0x0000011c,
+	PAUSE_OPCODE = 0x00000120,
+	PAUSE_TIMER = 0x00000124,
+	PAUSE_FRM_DEST_LO = 0x00000128,
+	PAUSE_FRM_DEST_HI = 0x0000012c,
+	MAC_TX_PARAMS = 0x00000134,
+	MAC_TX_PARAMS_JUMBO = (1 << 31),
+	MAC_TX_PARAMS_SIZE_SHIFT = 16,
+	MAC_RX_PARAMS = 0x00000138,
+	MAC_SYS_INT = 0x00000144,
+	MAC_SYS_INT_MASK = 0x00000148,
+	MAC_MGMT_INT = 0x0000014c,
+	MAC_MGMT_IN_MASK = 0x00000150,
+	EXT_ARB_MODE = 0x000001fc,
+
+	/* XGMAC TX statistics  registers */
+	TX_PKTS = 0x00000200,
+	TX_BYTES = 0x00000208,
+	TX_MCAST_PKTS = 0x00000210,
+	TX_BCAST_PKTS = 0x00000218,
+	TX_UCAST_PKTS = 0x00000220,
+	TX_CTL_PKTS = 0x00000228,
+	TX_PAUSE_PKTS = 0x00000230,
+	TX_64_PKT = 0x00000238,
+	TX_65_TO_127_PKT = 0x00000240,
+	TX_128_TO_255_PKT = 0x00000248,
+	TX_256_511_PKT = 0x00000250,
+	TX_512_TO_1023_PKT = 0x00000258,
+	TX_1024_TO_1518_PKT = 0x00000260,
+	TX_1519_TO_MAX_PKT = 0x00000268,
+	TX_UNDERSIZE_PKT = 0x00000270,
+	TX_OVERSIZE_PKT = 0x00000278,
+
+	/* XGMAC statistics control registers */
+	RX_HALF_FULL_DET = 0x000002a0,
+	TX_HALF_FULL_DET = 0x000002a4,
+	RX_OVERFLOW_DET = 0x000002a8,
+	TX_OVERFLOW_DET = 0x000002ac,
+	RX_HALF_FULL_MASK = 0x000002b0,
+	TX_HALF_FULL_MASK = 0x000002b4,
+	RX_OVERFLOW_MASK = 0x000002b8,
+	TX_OVERFLOW_MASK = 0x000002bc,
+	STAT_CNT_CTL = 0x000002c0,
+	STAT_CNT_CTL_CLEAR_TX = (1 << 0),
+	STAT_CNT_CTL_CLEAR_RX = (1 << 1),
+	AUX_RX_HALF_FULL_DET = 0x000002d0,
+	AUX_TX_HALF_FULL_DET = 0x000002d4,
+	AUX_RX_OVERFLOW_DET = 0x000002d8,
+	AUX_TX_OVERFLOW_DET = 0x000002dc,
+	AUX_RX_HALF_FULL_MASK = 0x000002f0,
+	AUX_TX_HALF_FULL_MASK = 0x000002f4,
+	AUX_RX_OVERFLOW_MASK = 0x000002f8,
+	AUX_TX_OVERFLOW_MASK = 0x000002fc,
+
+	/* XGMAC RX statistics  registers */
+	RX_BYTES = 0x00000300,
+	RX_BYTES_OK = 0x00000308,
+	RX_PKTS = 0x00000310,
+	RX_PKTS_OK = 0x00000318,
+	RX_BCAST_PKTS = 0x00000320,
+	RX_MCAST_PKTS = 0x00000328,
+	RX_UCAST_PKTS = 0x00000330,
+	RX_UNDERSIZE_PKTS = 0x00000338,
+	RX_OVERSIZE_PKTS = 0x00000340,
+	RX_JABBER_PKTS = 0x00000348,
+	RX_UNDERSIZE_FCERR_PKTS = 0x00000350,
+	RX_DROP_EVENTS = 0x00000358,
+	RX_FCERR_PKTS = 0x00000360,
+	RX_ALIGN_ERR = 0x00000368,
+	RX_SYMBOL_ERR = 0x00000370,
+	RX_MAC_ERR = 0x00000378,
+	RX_CTL_PKTS = 0x00000380,
+	RX_PAUSE_PKTS = 0x00000384,
+	RX_64_PKTS = 0x00000390,
+	RX_65_TO_127_PKTS = 0x00000398,
+	RX_128_255_PKTS = 0x000003a0,
+	RX_256_511_PKTS = 0x000003a8,
+	RX_512_TO_1023_PKTS = 0x000003b0,
+	RX_1024_TO_1518_PKTS = 0x000003b8,
+	RX_1519_TO_MAX_PKTS = 0x000003c0,
+	RX_LEN_ERR_PKTS = 0x000003c8,
+
+	/* XGMAC MDIO control registers */
+	MDIO_TX_DATA = 0x00000400,
+	MDIO_RX_DATA = 0x00000410,
+	MDIO_CMD = 0x00000420,
+	MDIO_PHY_ADDR = 0x00000430,
+	MDIO_PORT = 0x00000440,
+	MDIO_STATUS = 0x00000450,
+
+	/* XGMAC AUX statistics  registers */
+};
+
+/*
+ *  Enhanced Transmission Schedule Registers (NIC_ETS,CNA_ETS) bit definitions.
+ */
+enum {
+	ETS_QUEUE_SHIFT = 29,
+	ETS_REF = (1 << 26),
+	ETS_RS = (1 << 27),
+	ETS_P = (1 << 28),
+	ETS_FC_COS_SHIFT = 23,
+};
+
+/*
+ *  Flash Address Register (FLASH_ADDR) bit definitions.
+ */
+enum {
+	FLASH_ADDR_ERR = ADDR_ERR,
+	FLASH_ADDR_R = ADDR_R,
+	FLASH_ADDR_RDY = ADDR_RDY,
+};
+
+/*
+ *  Stop CQ Processing Register (CQ_STOP) bit definitions.
+ */
+enum {
+	CQ_STOP_QUEUE_MASK = (0x007f0000),
+	CQ_STOP_TYPE_MASK = (0x03000000),
+	CQ_STOP_TYPE_START = 0x00000100,
+	CQ_STOP_TYPE_STOP = 0x00000200,
+	CQ_STOP_TYPE_READ = 0x00000300,
+	CQ_STOP_EN = (1 << 15),
+};
+
+/*
+ *  MAC Protocol Address Index Register (MAC_ADDR_IDX) bit definitions.
+ */
+enum {
+	MAC_ADDR_IDX_SHIFT = 4,
+	MAC_ADDR_TYPE_SHIFT = 16,
+	MAC_ADDR_TYPE_MASK = 0x000f0000,
+	MAC_ADDR_TYPE_CAM_MAC = 0x00000000,
+	MAC_ADDR_TYPE_MULTI_MAC = 0x00010000,
+	MAC_ADDR_TYPE_VLAN = 0x00020000,
+	MAC_ADDR_TYPE_MULTI_FLTR = 0x00030000,
+	MAC_ADDR_TYPE_FC_MAC = 0x00040000,
+	MAC_ADDR_TYPE_MGMT_MAC = 0x00050000,
+	MAC_ADDR_TYPE_MGMT_VLAN = 0x00060000,
+	MAC_ADDR_TYPE_MGMT_V4 = 0x00070000,
+	MAC_ADDR_TYPE_MGMT_V6 = 0x00080000,
+	MAC_ADDR_TYPE_MGMT_TU_DP = 0x00090000,
+	MAC_ADDR_ADR = (1 << 25),
+	MAC_ADDR_RS = (1 << 26),
+	MAC_ADDR_E = (1 << 27),
+	MAC_ADDR_MR = (1 << 30),
+	MAC_ADDR_MW = (1 << 31),
+	MAX_MULTICAST_ENTRIES = 32,
+};
+
+/*
+ *  MAC Protocol Address Index Register (SPLT_HDR) bit definitions.
+ */
+enum {
+	SPLT_HDR_EP = (1 << 31),
+};
+
+/*
+ *  FCoE Receive Configuration Register (FC_RCV_CFG) bit definitions.
+ */
+enum {
+	FC_RCV_CFG_ECT = (1 << 15),
+	FC_RCV_CFG_DFH = (1 << 20),
+	FC_RCV_CFG_DVF = (1 << 21),
+	FC_RCV_CFG_RCE = (1 << 27),
+	FC_RCV_CFG_RFE = (1 << 28),
+	FC_RCV_CFG_TEE = (1 << 29),
+	FC_RCV_CFG_TCE = (1 << 30),
+	FC_RCV_CFG_TFE = (1 << 31),
+};
+
+/*
+ *  NIC Receive Configuration Register (NIC_RCV_CFG) bit definitions.
+ */
+enum {
+	NIC_RCV_CFG_PPE = (1 << 0),
+	NIC_RCV_CFG_VLAN_MASK = 0x00060000,
+	NIC_RCV_CFG_VLAN_ALL = 0x00000000,
+	NIC_RCV_CFG_VLAN_MATCH_ONLY = 0x00000002,
+	NIC_RCV_CFG_VLAN_MATCH_AND_NON = 0x00000004,
+	NIC_RCV_CFG_VLAN_NONE_AND_NON = 0x00000006,
+	NIC_RCV_CFG_RV = (1 << 3),
+	NIC_RCV_CFG_DFQ_MASK = (0x7f000000),
+	NIC_RCV_CFG_DFQ_SHIFT = 8,
+	NIC_RCV_CFG_DFQ = 0,	/* HARDCODE default queue to 0. */
+};
+
+/*
+ *   Mgmt Receive Configuration Register (MGMT_RCV_CFG) bit definitions.
+ */
+enum {
+	MGMT_RCV_CFG_ARP = (1 << 0),
+	MGMT_RCV_CFG_DHC = (1 << 1),
+	MGMT_RCV_CFG_DHS = (1 << 2),
+	MGMT_RCV_CFG_NP = (1 << 3),
+	MGMT_RCV_CFG_I6N = (1 << 4),
+	MGMT_RCV_CFG_I6R = (1 << 5),
+	MGMT_RCV_CFG_DH6 = (1 << 6),
+	MGMT_RCV_CFG_UD1 = (1 << 7),
+	MGMT_RCV_CFG_UD0 = (1 << 8),
+	MGMT_RCV_CFG_BCT = (1 << 9),
+	MGMT_RCV_CFG_MCT = (1 << 10),
+	MGMT_RCV_CFG_DM = (1 << 11),
+	MGMT_RCV_CFG_RM = (1 << 12),
+	MGMT_RCV_CFG_STL = (1 << 13),
+	MGMT_RCV_CFG_VLAN_MASK = 0xc0000000,
+	MGMT_RCV_CFG_VLAN_ALL = 0x00000000,
+	MGMT_RCV_CFG_VLAN_MATCH_ONLY = 0x00004000,
+	MGMT_RCV_CFG_VLAN_MATCH_AND_NON = 0x00008000,
+	MGMT_RCV_CFG_VLAN_NONE_AND_NON = 0x0000c000,
+};
+
+/*
+ *  Routing Index Register (RT_IDX) bit definitions.
+ */
+enum {
+	RT_IDX_IDX_SHIFT = 8,
+	RT_IDX_TYPE_MASK = 0x000f0000,
+	RT_IDX_TYPE_RT = 0x00000000,
+	RT_IDX_TYPE_RT_INV = 0x00010000,
+	RT_IDX_TYPE_NICQ = 0x00020000,
+	RT_IDX_TYPE_NICQ_INV = 0x00030000,
+	RT_IDX_DST_MASK = 0x00700000,
+	RT_IDX_DST_RSS = 0x00000000,
+	RT_IDX_DST_CAM_Q = 0x00100000,
+	RT_IDX_DST_COS_Q = 0x00200000,
+	RT_IDX_DST_DFLT_Q = 0x00300000,
+	RT_IDX_DST_DEST_Q = 0x00400000,
+	RT_IDX_RS = (1 << 26),
+	RT_IDX_E = (1 << 27),
+	RT_IDX_MR = (1 << 30),
+	RT_IDX_MW = (1 << 31),
+
+	/* Nic Queue format - type 2 bits */
+	RT_IDX_BCAST = (1 << 0),
+	RT_IDX_MCAST = (1 << 1),
+	RT_IDX_MCAST_MATCH = (1 << 2),
+	RT_IDX_MCAST_REG_MATCH = (1 << 3),
+	RT_IDX_MCAST_HASH_MATCH = (1 << 4),
+	RT_IDX_FC_MACH = (1 << 5),
+	RT_IDX_ETH_FCOE = (1 << 6),
+	RT_IDX_CAM_HIT = (1 << 7),
+	RT_IDX_CAM_BIT0 = (1 << 8),
+	RT_IDX_CAM_BIT1 = (1 << 9),
+	RT_IDX_VLAN_TAG = (1 << 10),
+	RT_IDX_VLAN_MATCH = (1 << 11),
+	RT_IDX_VLAN_FILTER = (1 << 12),
+	RT_IDX_ETH_SKIP1 = (1 << 13),
+	RT_IDX_ETH_SKIP2 = (1 << 14),
+	RT_IDX_BCAST_MCAST_MATCH = (1 << 15),
+	RT_IDX_802_3 = (1 << 16),
+	RT_IDX_LLDP = (1 << 17),
+	RT_IDX_UNUSED018 = (1 << 18),
+	RT_IDX_UNUSED019 = (1 << 19),
+	RT_IDX_UNUSED20 = (1 << 20),
+	RT_IDX_UNUSED21 = (1 << 21),
+	RT_IDX_ERR = (1 << 22),
+	RT_IDX_VALID = (1 << 23),
+	RT_IDX_TU_CSUM_ERR = (1 << 24),
+	RT_IDX_IP_CSUM_ERR = (1 << 25),
+	RT_IDX_MAC_ERR = (1 << 26),
+	RT_IDX_RSS_TCP6 = (1 << 27),
+	RT_IDX_RSS_TCP4 = (1 << 28),
+	RT_IDX_RSS_IPV6 = (1 << 29),
+	RT_IDX_RSS_IPV4 = (1 << 30),
+	RT_IDX_RSS_MATCH = (1 << 31),
+
+	/* Hierarchy for the NIC Queue Mask */
+	RT_IDX_ALL_ERR_SLOT = 0,
+	RT_IDX_MAC_ERR_SLOT = 0,
+	RT_IDX_IP_CSUM_ERR_SLOT = 1,
+	RT_IDX_TCP_UDP_CSUM_ERR_SLOT = 2,
+	RT_IDX_BCAST_SLOT = 3,
+	RT_IDX_MCAST_MATCH_SLOT = 4,
+	RT_IDX_ALLMULTI_SLOT = 5,
+	RT_IDX_UNUSED6_SLOT = 6,
+	RT_IDX_UNUSED7_SLOT = 7,
+	RT_IDX_RSS_MATCH_SLOT = 8,
+	RT_IDX_RSS_IPV4_SLOT = 8,
+	RT_IDX_RSS_IPV6_SLOT = 9,
+	RT_IDX_RSS_TCP4_SLOT = 10,
+	RT_IDX_RSS_TCP6_SLOT = 11,
+	RT_IDX_CAM_HIT_SLOT = 12,
+	RT_IDX_UNUSED013 = 13,
+	RT_IDX_UNUSED014 = 14,
+	RT_IDX_PROMISCUOUS_SLOT = 15,
+	RT_IDX_MAX_SLOTS = 16,
+};
+
+/*
+ * Control Register Set Map
+ */
+enum {
+	PROC_ADDR = 0,		/* Use semaphore */
+	PROC_DATA = 0x04,	/* Use semaphore */
+	SYS = 0x08,
+	RST_FO = 0x0c,
+	FSC = 0x10,
+	CSR = 0x14,
+	LED = 0x18,
+	ICB_RID = 0x1c,		/* Use semaphore */
+	ICB_L = 0x20,		/* Use semaphore */
+	ICB_H = 0x24,		/* Use semaphore */
+	CFG = 0x28,
+	BIOS_ADDR = 0x2c,
+	STS = 0x30,
+	INTR_EN = 0x34,
+	INTR_MASK = 0x38,
+	ISR1 = 0x3c,
+	ISR2 = 0x40,
+	ISR3 = 0x44,
+	ISR4 = 0x48,
+	REV_ID = 0x4c,
+	FRC_ECC_ERR = 0x50,
+	ERR_STS = 0x54,
+	RAM_DBG_ADDR = 0x58,
+	RAM_DBG_DATA = 0x5c,
+	ECC_ERR_CNT = 0x60,
+	SEM = 0x64,
+	GPIO_1 = 0x68,		/* Use semaphore */
+	GPIO_2 = 0x6c,		/* Use semaphore */
+	GPIO_3 = 0x70,		/* Use semaphore */
+	RSVD2 = 0x74,
+	XGMAC_ADDR = 0x78,	/* Use semaphore */
+	XGMAC_DATA = 0x7c,	/* Use semaphore */
+	NIC_ETS = 0x80,
+	CNA_ETS = 0x84,
+	FLASH_ADDR = 0x88,	/* Use semaphore */
+	FLASH_DATA = 0x8c,	/* Use semaphore */
+	CQ_STOP = 0x90,
+	PAGE_TBL_RID = 0x94,
+	WQ_PAGE_TBL_LO = 0x98,
+	WQ_PAGE_TBL_HI = 0x9c,
+	CQ_PAGE_TBL_LO = 0xa0,
+	CQ_PAGE_TBL_HI = 0xa4,
+	MAC_ADDR_IDX = 0xa8,	/* Use semaphore */
+	MAC_ADDR_DATA = 0xac,	/* Use semaphore */
+	COS_DFLT_CQ1 = 0xb0,
+	COS_DFLT_CQ2 = 0xb4,
+	ETYPE_SKIP1 = 0xb8,
+	ETYPE_SKIP2 = 0xbc,
+	SPLT_HDR = 0xc0,
+	FC_PAUSE_THRES = 0xc4,
+	NIC_PAUSE_THRES = 0xc8,
+	FC_ETHERTYPE = 0xcc,
+	FC_RCV_CFG = 0xd0,
+	NIC_RCV_CFG = 0xd4,
+	FC_COS_TAGS = 0xd8,
+	NIC_COS_TAGS = 0xdc,
+	MGMT_RCV_CFG = 0xe0,
+	RT_IDX = 0xe4,
+	RT_DATA = 0xe8,
+	RSVD7 = 0xec,
+	XG_SERDES_ADDR = 0xf0,
+	XG_SERDES_DATA = 0xf4,
+	PRB_MX_ADDR = 0xf8,	/* Use semaphore */
+	PRB_MX_DATA = 0xfc,	/* Use semaphore */
+};
+
+/*
+ * CAM output format.
+ */
+enum {
+	CAM_OUT_ROUTE_FC = 0,
+	CAM_OUT_ROUTE_NIC = 1,
+	CAM_OUT_FUNC_SHIFT = 2,
+	CAM_OUT_RV = (1 << 4),
+	CAM_OUT_SH = (1 << 15),
+	CAM_OUT_CQ_ID_SHIFT = 5,
+};
+
+/*
+ * Mailbox  definitions
+ */
+enum {
+	/* Asynchronous Event Notifications */
+	AEN_SYS_ERR = 0x00008002,
+	AEN_LINK_UP = 0x00008011,
+	AEN_LINK_DOWN = 0x00008012,
+	AEN_IDC_CMPLT = 0x00008100,
+	AEN_IDC_REQ = 0x00008101,
+	AEN_FW_INIT_DONE = 0x00008400,
+	AEN_FW_INIT_FAIL = 0x00008401,
+
+	/* Mailbox Command Opcodes. */
+	MB_CMD_NOP = 0x00000000,
+	MB_CMD_EX_FW = 0x00000002,
+	MB_CMD_MB_TEST = 0x00000006,
+	MB_CMD_CSUM_TEST = 0x00000007,	/* Verify Checksum */
+	MB_CMD_ABOUT_FW = 0x00000008,
+	MB_CMD_LOAD_RISC_RAM = 0x0000000b,
+	MB_CMD_DUMP_RISC_RAM = 0x0000000c,
+	MB_CMD_WRITE_RAM = 0x0000000d,
+	MB_CMD_READ_RAM = 0x0000000f,
+	MB_CMD_STOP_FW = 0x00000014,
+	MB_CMD_MAKE_SYS_ERR = 0x0000002a,
+	MB_CMD_INIT_FW = 0x00000060,
+	MB_CMD_GET_INIT_CB = 0x00000061,
+	MB_CMD_GET_FW_STATE = 0x00000069,
+	MB_CMD_IDC_REQ = 0x00000100,	/* Inter-Driver Communication */
+	MB_CMD_IDC_ACK = 0x00000101,	/* Inter-Driver Communication */
+	MB_CMD_SET_WOL_MODE = 0x00000110,	/* Wake On Lan */
+	MB_WOL_DISABLE = 0x00000000,
+	MB_WOL_MAGIC_PKT = 0x00000001,
+	MB_WOL_FLTR = 0x00000002,
+	MB_WOL_UCAST = 0x00000004,
+	MB_WOL_MCAST = 0x00000008,
+	MB_WOL_BCAST = 0x00000010,
+	MB_WOL_LINK_UP = 0x00000020,
+	MB_WOL_LINK_DOWN = 0x00000040,
+	MB_CMD_SET_WOL_FLTR = 0x00000111,	/* Wake On Lan Filter */
+	MB_CMD_CLEAR_WOL_FLTR = 0x00000112,	/* Wake On Lan Filter */
+	MB_CMD_SET_WOL_MAGIC = 0x00000113,	/* Wake On Lan Magic Packet */
+	MB_CMD_CLEAR_WOL_MAGIC = 0x00000114,	/* Wake On Lan Magic Packet */
+	MB_CMD_PORT_RESET = 0x00000120,
+	MB_CMD_SET_PORT_CFG = 0x00000122,
+	MB_CMD_GET_PORT_CFG = 0x00000123,
+	MB_CMD_SET_ASIC_VOLTS = 0x00000130,
+	MB_CMD_GET_SNS_DATA = 0x00000131,	/* Temp and Volt Sense data. */
+
+	/* Mailbox Command Status. */
+	MB_CMD_STS_GOOD = 0x00004000,	/* Success. */
+	MB_CMD_STS_INTRMDT = 0x00001000,	/* Intermediate Complete. */
+	MB_CMD_STS_ERR = 0x00004005,	/* Error. */
+};
+
+struct mbox_params {
+	u32 mbox_in[MAILBOX_COUNT];
+	u32 mbox_out[MAILBOX_COUNT];
+	int in_count;
+	int out_count;
+};
+
+/*
+ * doorbell space for the rx ring context
+ */
+struct rx_doorbell_context {
+	u32 cnsmr_idx;		/* 0x00 */
+	u32 valid;		/* 0x04 */
+	u32 reserved[4];	/* 0x08-0x14 */
+	u32 lbq_prod_idx;	/* 0x18 */
+	u32 sbq_prod_idx;	/* 0x1c */
+};
+
+/*
+ * doorbell space for the tx ring context
+ */
+struct tx_doorbell_context {
+	u32 prod_idx;		/* 0x00 */
+	u32 valid;		/* 0x04 */
+	u32 reserved[4];	/* 0x08-0x14 */
+	u32 lbq_prod_idx;	/* 0x18 */
+	u32 sbq_prod_idx;	/* 0x1c */
+};
+
+/* DATA STRUCTURES SHARED WITH HARDWARE. */
+
+struct bq_element {
+	u32 addr_lo;
+#define BQ_END	0x00000001
+#define BQ_CONT	0x00000002
+#define BQ_MASK	0x00000003
+	u32 addr_hi;
+} __attribute((packed));
+
+struct tx_buf_desc {
+	__le64 addr;
+	__le32 len;
+#define TX_DESC_LEN_MASK	0x000fffff
+#define TX_DESC_C	0x40000000
+#define TX_DESC_E	0x80000000
+} __attribute((packed));
+
+/*
+ * IOCB Definitions...
+ */
+
+#define OPCODE_OB_MAC_IOCB 			0x01
+#define OPCODE_OB_MAC_TSO_IOCB		0x02
+#define OPCODE_IB_MAC_IOCB			0x20
+#define OPCODE_IB_MPI_IOCB			0x21
+#define OPCODE_IB_AE_IOCB			0x3f
+
+struct ob_mac_iocb_req {
+	u8 opcode;
+	u8 flags1;
+#define OB_MAC_IOCB_REQ_OI	0x01
+#define OB_MAC_IOCB_REQ_I	0x02
+#define OB_MAC_IOCB_REQ_D	0x08
+#define OB_MAC_IOCB_REQ_F	0x10
+	u8 flags2;
+	u8 flags3;
+#define OB_MAC_IOCB_DFP	0x02
+#define OB_MAC_IOCB_V	0x04
+	__le32 reserved1[2];
+	__le16 frame_len;
+#define OB_MAC_IOCB_LEN_MASK 0x3ffff
+	__le16 reserved2;
+	__le32 tid;
+	__le32 txq_idx;
+	__le32 reserved3;
+	__le16 vlan_tci;
+	__le16 reserved4;
+	struct tx_buf_desc tbd[TX_DESC_PER_IOCB];
+} __attribute((packed));
+
+struct ob_mac_iocb_rsp {
+	u8 opcode;		/* */
+	u8 flags1;		/* */
+#define OB_MAC_IOCB_RSP_OI	0x01	/* */
+#define OB_MAC_IOCB_RSP_I	0x02	/* */
+#define OB_MAC_IOCB_RSP_E	0x08	/* */
+#define OB_MAC_IOCB_RSP_S	0x10	/* too Short */
+#define OB_MAC_IOCB_RSP_L	0x20	/* too Large */
+#define OB_MAC_IOCB_RSP_P	0x40	/* Padded */
+	u8 flags2;		/* */
+	u8 flags3;		/* */
+#define OB_MAC_IOCB_RSP_B	0x80	/* */
+	__le32 tid;
+	__le32 txq_idx;
+	__le32 reserved[13];
+} __attribute((packed));
+
+struct ob_mac_tso_iocb_req {
+	u8 opcode;
+	u8 flags1;
+#define OB_MAC_TSO_IOCB_OI	0x01
+#define OB_MAC_TSO_IOCB_I	0x02
+#define OB_MAC_TSO_IOCB_D	0x08
+#define OB_MAC_TSO_IOCB_IP4	0x40
+#define OB_MAC_TSO_IOCB_IP6	0x80
+	u8 flags2;
+#define OB_MAC_TSO_IOCB_LSO	0x20
+#define OB_MAC_TSO_IOCB_UC	0x40
+#define OB_MAC_TSO_IOCB_TC	0x80
+	u8 flags3;
+#define OB_MAC_TSO_IOCB_IC	0x01
+#define OB_MAC_TSO_IOCB_DFP	0x02
+#define OB_MAC_TSO_IOCB_V	0x04
+	__le32 reserved1[2];
+	__le32 frame_len;
+	__le32 tid;
+	__le32 txq_idx;
+	__le16 total_hdrs_len;
+	__le16 net_trans_offset;
+#define OB_MAC_TRANSPORT_HDR_SHIFT 6
+	__le16 vlan_tci;
+	__le16 mss;
+	struct tx_buf_desc tbd[TX_DESC_PER_IOCB];
+} __attribute((packed));
+
+struct ob_mac_tso_iocb_rsp {
+	u8 opcode;
+	u8 flags1;
+#define OB_MAC_TSO_IOCB_RSP_OI	0x01
+#define OB_MAC_TSO_IOCB_RSP_I	0x02
+#define OB_MAC_TSO_IOCB_RSP_E	0x08
+#define OB_MAC_TSO_IOCB_RSP_S	0x10
+#define OB_MAC_TSO_IOCB_RSP_L	0x20
+#define OB_MAC_TSO_IOCB_RSP_P	0x40
+	u8 flags2;		/* */
+	u8 flags3;		/* */
+#define OB_MAC_TSO_IOCB_RSP_B	0x8000
+	__le32 tid;
+	__le32 txq_idx;
+	__le32 reserved2[13];
+} __attribute((packed));
+
+struct ib_mac_iocb_rsp {
+	u8 opcode;		/* 0x20 */
+	u8 flags1;
+#define IB_MAC_IOCB_RSP_OI	0x01	/* Overide intr delay */
+#define IB_MAC_IOCB_RSP_I	0x02	/* Disble Intr Generation */
+#define IB_MAC_IOCB_RSP_TE	0x04	/* Checksum error */
+#define IB_MAC_IOCB_RSP_NU	0x08	/* No checksum rcvd */
+#define IB_MAC_IOCB_RSP_IE	0x10	/* IPv4 checksum error */
+#define IB_MAC_IOCB_RSP_M_MASK	0x60	/* Multicast info */
+#define IB_MAC_IOCB_RSP_M_NONE	0x00	/* Not mcast frame */
+#define IB_MAC_IOCB_RSP_M_HASH	0x20	/* HASH mcast frame */
+#define IB_MAC_IOCB_RSP_M_REG 	0x40	/* Registered mcast frame */
+#define IB_MAC_IOCB_RSP_M_PROM 	0x60	/* Promiscuous mcast frame */
+#define IB_MAC_IOCB_RSP_B	0x80	/* Broadcast frame */
+	u8 flags2;
+#define IB_MAC_IOCB_RSP_P	0x01	/* Promiscuous frame */
+#define IB_MAC_IOCB_RSP_V	0x02	/* Vlan tag present */
+#define IB_MAC_IOCB_RSP_ERR_MASK	0x1c	/*  */
+#define IB_MAC_IOCB_RSP_ERR_CODE_ERR	0x04
+#define IB_MAC_IOCB_RSP_ERR_OVERSIZE	0x08
+#define IB_MAC_IOCB_RSP_ERR_UNDERSIZE	0x10
+#define IB_MAC_IOCB_RSP_ERR_PREAMBLE	0x14
+#define IB_MAC_IOCB_RSP_ERR_FRAME_LEN	0x18
+#define IB_MAC_IOCB_RSP_ERR_CRC		0x1c
+#define IB_MAC_IOCB_RSP_U	0x20	/* UDP packet */
+#define IB_MAC_IOCB_RSP_T	0x40	/* TCP packet */
+#define IB_MAC_IOCB_RSP_FO	0x80	/* Failover port */
+	u8 flags3;
+#define IB_MAC_IOCB_RSP_RSS_MASK	0x07	/* RSS mask */
+#define IB_MAC_IOCB_RSP_M_NONE	0x00	/* No RSS match */
+#define IB_MAC_IOCB_RSP_M_IPV4	0x04	/* IPv4 RSS match */
+#define IB_MAC_IOCB_RSP_M_IPV6	0x02	/* IPv6 RSS match */
+#define IB_MAC_IOCB_RSP_M_TCP_V4 	0x05	/* TCP with IPv4 */
+#define IB_MAC_IOCB_RSP_M_TCP_V6 	0x03	/* TCP with IPv6 */
+#define IB_MAC_IOCB_RSP_V4	0x08	/* IPV4 */
+#define IB_MAC_IOCB_RSP_V6	0x10	/* IPV6 */
+#define IB_MAC_IOCB_RSP_IH	0x20	/* Split after IP header */
+#define IB_MAC_IOCB_RSP_DS	0x40	/* data is in small buffer */
+#define IB_MAC_IOCB_RSP_DL	0x80	/* data is in large buffer */
+	__le32 data_len;	/* */
+	__le32 data_addr_lo;	/* */
+	__le32 data_addr_hi;	/* */
+	__le32 rss;		/* */
+	__le16 vlan_id;		/* 12 bits */
+#define IB_MAC_IOCB_RSP_C	0x1000	/* VLAN CFI bit */
+#define IB_MAC_IOCB_RSP_COS_SHIFT	12	/* class of service value */
+
+	__le16 reserved1;
+	__le32 reserved2[6];
+	__le32 flags4;
+#define IB_MAC_IOCB_RSP_HV	0x20000000	/* */
+#define IB_MAC_IOCB_RSP_HS	0x40000000	/* */
+#define IB_MAC_IOCB_RSP_HL	0x80000000	/* */
+	__le32 hdr_len;		/* */
+	__le32 hdr_addr_lo;	/* */
+	__le32 hdr_addr_hi;	/* */
+} __attribute((packed));
+
+struct ib_ae_iocb_rsp {
+	u8 opcode;
+	u8 flags1;
+#define IB_AE_IOCB_RSP_OI		0x01
+#define IB_AE_IOCB_RSP_I		0x02
+	u8 event;
+#define LINK_UP_EVENT              0x00
+#define LINK_DOWN_EVENT            0x01
+#define CAM_LOOKUP_ERR_EVENT       0x06
+#define SOFT_ECC_ERROR_EVENT       0x07
+#define MGMT_ERR_EVENT             0x08
+#define TEN_GIG_MAC_EVENT          0x09
+#define GPI0_H2L_EVENT       	0x10
+#define GPI0_L2H_EVENT       	0x20
+#define GPI1_H2L_EVENT       	0x11
+#define GPI1_L2H_EVENT       	0x21
+#define PCI_ERR_ANON_BUF_RD        0x40
+	u8 q_id;
+	__le32 reserved[15];
+} __attribute((packed));
+
+/*
+ * These three structures are for generic
+ * handling of ib and ob iocbs.
+ */
+struct ql_net_rsp_iocb {
+	u8 opcode;
+	u8 flags0;
+	__le16 length;
+	__le32 tid;
+	__le32 reserved[14];
+} __attribute((packed));
+
+struct net_req_iocb {
+	u8 opcode;
+	u8 flags0;
+	__le16 flags1;
+	__le32 tid;
+	__le32 reserved1[30];
+} __attribute((packed));
+
+/*
+ * tx ring initialization control block for chip.
+ * It is defined as:
+ * "Work Queue Initialization Control Block"
+ */
+struct wqicb {
+	__le16 len;
+#define Q_LEN_V		(1 << 4)
+#define Q_LEN_CPP_CONT	0x0000
+#define Q_LEN_CPP_16	0x0001
+#define Q_LEN_CPP_32	0x0002
+#define Q_LEN_CPP_64	0x0003
+	__le16 flags;
+#define Q_PRI_SHIFT	1
+#define Q_FLAGS_LC	0x1000
+#define Q_FLAGS_LB	0x2000
+#define Q_FLAGS_LI	0x4000
+#define Q_FLAGS_LO	0x8000
+	__le16 cq_id_rss;
+#define Q_CQ_ID_RSS_RV 0x8000
+	__le16 rid;
+	__le32 addr_lo;
+	__le32 addr_hi;
+	__le32 cnsmr_idx_addr_lo;
+	__le32 cnsmr_idx_addr_hi;
+} __attribute((packed));
+
+/*
+ * rx ring initialization control block for chip.
+ * It is defined as:
+ * "Completion Queue Initialization Control Block"
+ */
+struct cqicb {
+	u8 msix_vect;
+	u8 reserved1;
+	u8 reserved2;
+	u8 flags;
+#define FLAGS_LV	0x08
+#define FLAGS_LS	0x10
+#define FLAGS_LL	0x20
+#define FLAGS_LI	0x40
+#define FLAGS_LC	0x80
+	__le16 len;
+#define LEN_V		(1 << 4)
+#define LEN_CPP_CONT	0x0000
+#define LEN_CPP_32	0x0001
+#define LEN_CPP_64	0x0002
+#define LEN_CPP_128	0x0003
+	__le16 rid;
+	__le32 addr_lo;
+	__le32 addr_hi;
+	__le32 prod_idx_addr_lo;
+	__le32 prod_idx_addr_hi;
+	__le16 pkt_delay;
+	__le16 irq_delay;
+	__le32 lbq_addr_lo;
+	__le32 lbq_addr_hi;
+	__le16 lbq_buf_size;
+	__le16 lbq_len;		/* entry count */
+	__le32 sbq_addr_lo;
+	__le32 sbq_addr_hi;
+	__le16 sbq_buf_size;
+	__le16 sbq_len;		/* entry count */
+} __attribute((packed));
+
+struct ricb {
+	u8 base_cq;
+#define RSS_L4K 0x80
+	u8 flags;
+#define RSS_L6K 0x01
+#define RSS_LI  0x02
+#define RSS_LB  0x04
+#define RSS_LM  0x08
+#define RSS_RI4 0x10
+#define RSS_RT4 0x20
+#define RSS_RI6 0x40
+#define RSS_RT6 0x80
+	__le16 mask;
+	__le32 hash_cq_id[256];
+	__le32 ipv6_hash_key[10];
+	__le32 ipv4_hash_key[4];
+} __attribute((packed));
+
+/* SOFTWARE/DRIVER DATA STRUCTURES. */
+
+struct oal {
+	struct tx_buf_desc oal[TX_DESC_PER_OAL];
+};
+
+struct map_list {
+	DECLARE_PCI_UNMAP_ADDR(mapaddr);
+	DECLARE_PCI_UNMAP_LEN(maplen);
+};
+
+struct tx_ring_desc {
+	struct sk_buff *skb;
+	struct ob_mac_iocb_req *queue_entry;
+	int index;
+	struct oal oal;
+	struct map_list map[MAX_SKB_FRAGS + 1];
+	int map_cnt;
+	struct tx_ring_desc *next;
+};
+
+struct bq_desc {
+	union {
+		struct page *lbq_page;
+		struct sk_buff *skb;
+	} p;
+	struct bq_element *bq;
+	int index;
+	 DECLARE_PCI_UNMAP_ADDR(mapaddr);
+	 DECLARE_PCI_UNMAP_LEN(maplen);
+};
+
+enum link_state {
+	LINK_UNKNOWN = 0,
+	LINK_DOWN,
+	LINK_DEGRADE,
+	LINK_RECOVER,
+	LINK_UP,
+};
+
+#define QL_TXQ_IDX(qdev, skb) (smp_processor_id()%(qdev->tx_ring_count))
+
+struct tx_ring {
+	/*
+	 * queue info.
+	 */
+	struct wqicb wqicb;	/* structure used to inform chip of new queue */
+	void *wq_base;		/* pci_alloc:virtual addr for tx */
+	dma_addr_t wq_base_dma;	/* pci_alloc:dma addr for tx */
+	u32 *cnsmr_idx_sh_reg;	/* shadow copy of consumer idx */
+	dma_addr_t cnsmr_idx_sh_reg_dma;	/* dma-shadow copy of consumer */
+	u32 wq_size;		/* size in bytes of queue area */
+	u32 wq_len;		/* number of entries in queue */
+	void __iomem *prod_idx_db_reg;	/* doorbell area index reg at offset 0x00 */
+	void __iomem *valid_db_reg;	/* doorbell area valid reg at offset 0x04 */
+	u16 prod_idx;		/* current value for prod idx */
+	u16 cq_id;		/* completion (rx) queue for tx completions */
+	u8 wq_id;		/* queue id for this entry */
+	u8 reserved1[3];
+	struct tx_ring_desc *q;	/* descriptor list for the queue */
+	spinlock_t lock;
+	atomic_t tx_count;	/* counts down for every outstanding IO */
+	atomic_t queue_stopped;	/* Turns queue off when full. */
+	struct delayed_work tx_work;
+	struct ql_adapter *qdev;
+};
+
+/*
+ * Type of inbound queue.
+ */
+enum {
+	DEFAULT_Q = 2,		/* Handles slow queue and chip/MPI events. */
+	TX_Q = 3,		/* Handles outbound completions. */
+	RX_Q = 4,		/* Handles inbound completions. */
+};
+
+struct rx_ring {
+	struct cqicb cqicb;	/* The chip's completion queue init control block. */
+
+	/* Completion queue elements. */
+	void *cq_base;
+	dma_addr_t cq_base_dma;
+	u32 cq_size;
+	u32 cq_len;
+	u16 cq_id;
+	u32 *prod_idx_sh_reg;	/* Shadowed producer register. */
+	dma_addr_t prod_idx_sh_reg_dma;
+	void __iomem *cnsmr_idx_db_reg;	/* PCI doorbell mem area + 0 */
+	u32 cnsmr_idx;		/* current sw idx */
+	struct ql_net_rsp_iocb *curr_entry;	/* next entry on queue */
+	void __iomem *valid_db_reg;	/* PCI doorbell mem area + 0x04 */
+
+	/* Large buffer queue elements. */
+	u32 lbq_len;		/* entry count */
+	u32 lbq_size;		/* size in bytes of queue */
+	u32 lbq_buf_size;
+	void *lbq_base;
+	dma_addr_t lbq_base_dma;
+	void *lbq_base_indirect;
+	dma_addr_t lbq_base_indirect_dma;
+	struct bq_desc *lbq;	/* array of control blocks */
+	void __iomem *lbq_prod_idx_db_reg;	/* PCI doorbell mem area + 0x18 */
+	u32 lbq_prod_idx;	/* current sw prod idx */
+	u32 lbq_curr_idx;	/* next entry we expect */
+	u32 lbq_clean_idx;	/* beginning of new descs */
+	u32 lbq_free_cnt;	/* free buffer desc cnt */
+
+	/* Small buffer queue elements. */
+	u32 sbq_len;		/* entry count */
+	u32 sbq_size;		/* size in bytes of queue */
+	u32 sbq_buf_size;
+	void *sbq_base;
+	dma_addr_t sbq_base_dma;
+	void *sbq_base_indirect;
+	dma_addr_t sbq_base_indirect_dma;
+	struct bq_desc *sbq;	/* array of control blocks */
+	void __iomem *sbq_prod_idx_db_reg; /* PCI doorbell mem area + 0x1c */
+	u32 sbq_prod_idx;	/* current sw prod idx */
+	u32 sbq_curr_idx;	/* next entry we expect */
+	u32 sbq_clean_idx;	/* beginning of new descs */
+	u32 sbq_free_cnt;	/* free buffer desc cnt */
+
+	/* Misc. handler elements. */
+	u32 type;		/* Type of queue, tx, rx, or default. */
+	u32 irq;		/* Which vector this ring is assigned. */
+	u32 cpu;		/* Which CPU this should run on. */
+	char name[IFNAMSIZ + 5];
+	struct napi_struct napi;
+	struct delayed_work rx_work;
+	u8 reserved;
+	struct ql_adapter *qdev;
+};
+
+/*
+ * RSS Initialization Control Block
+ */
+struct hash_id {
+	u8 value[4];
+};
+
+struct nic_stats {
+	/*
+	 * These stats come from offset 200h to 278h
+	 * in the XGMAC register.
+	 */
+	u64 tx_pkts;
+	u64 tx_bytes;
+	u64 tx_mcast_pkts;
+	u64 tx_bcast_pkts;
+	u64 tx_ucast_pkts;
+	u64 tx_ctl_pkts;
+	u64 tx_pause_pkts;
+	u64 tx_64_pkt;
+	u64 tx_65_to_127_pkt;
+	u64 tx_128_to_255_pkt;
+	u64 tx_256_511_pkt;
+	u64 tx_512_to_1023_pkt;
+	u64 tx_1024_to_1518_pkt;
+	u64 tx_1519_to_max_pkt;
+	u64 tx_undersize_pkt;
+	u64 tx_oversize_pkt;
+
+	/*
+	 * These stats come from offset 300h to 3C8h
+	 * in the XGMAC register.
+	 */
+	u64 rx_bytes;
+	u64 rx_bytes_ok;
+	u64 rx_pkts;
+	u64 rx_pkts_ok;
+	u64 rx_bcast_pkts;
+	u64 rx_mcast_pkts;
+	u64 rx_ucast_pkts;
+	u64 rx_undersize_pkts;
+	u64 rx_oversize_pkts;
+	u64 rx_jabber_pkts;
+	u64 rx_undersize_fcerr_pkts;
+	u64 rx_drop_events;
+	u64 rx_fcerr_pkts;
+	u64 rx_align_err;
+	u64 rx_symbol_err;
+	u64 rx_mac_err;
+	u64 rx_ctl_pkts;
+	u64 rx_pause_pkts;
+	u64 rx_64_pkts;
+	u64 rx_65_to_127_pkts;
+	u64 rx_128_255_pkts;
+	u64 rx_256_511_pkts;
+	u64 rx_512_to_1023_pkts;
+	u64 rx_1024_to_1518_pkts;
+	u64 rx_1519_to_max_pkts;
+	u64 rx_len_err_pkts;
+};
+
+/*
+ * intr_context structure is used during initialization
+ * to hook the interrupts.  It is also used in a single
+ * irq environment as a context to the ISR.
+ */
+struct intr_context {
+	struct ql_adapter *qdev;
+	u32 intr;
+	u32 hooked;
+	u32 intr_en_mask;	/* value/mask used to enable this intr */
+	u32 intr_dis_mask;	/* value/mask used to disable this intr */
+	u32 intr_read_mask;	/* value/mask used to read this intr */
+	char name[IFNAMSIZ * 2];
+	atomic_t irq_cnt;	/* irq_cnt is used in single vector
+				 * environment.  It's incremented for each
+				 * irq handler that is scheduled.  When each
+				 * handler finishes it decrements irq_cnt and
+				 * enables interrupts if it's zero. */
+	irq_handler_t handler;
+};
+
+/* adapter flags definitions. */
+enum {
+	QL_ADAPTER_UP = (1 << 0),	/* Adapter has been brought up. */
+	QL_LINK_UP = (1 << 1),	/* Link Status. */
+	QL_LINK_OPTICAL = (1 << 2),
+	QL_MSI_ENABLED = (1 << 3),
+	QL_MSIX_ENABLED = (1 << 4),
+	QL_DMA64 = (1 << 5),
+	QL_PROMISCUOUS = (1 << 6),
+	QL_ALLMULTI = (1 << 7),
+};
+
+/*
+ * The main Adapter structure definition.
+ * This structure has all fields relevant to the hardware.
+ */
+struct ql_adapter {
+	struct ricb ricb;
+	unsigned long flags;
+	u32 wol;
+
+	struct nic_stats nic_stats;
+
+	struct vlan_group *vlgrp;
+
+	/* PCI Configuration information for this device */
+	struct pci_dev *pdev;
+	struct net_device *ndev;	/* Parent NET device */
+
+	/* Hardware information */
+	u32 chip_rev_id;
+	u32 func;		/* PCI function for this adapter */
+
+	spinlock_t adapter_lock;
+	spinlock_t hw_lock;
+	spinlock_t stats_lock;
+	spinlock_t legacy_lock;	/* used for maintaining legacy intr sync */
+
+	/* PCI Bus Relative Register Addresses */
+	void __iomem *reg_base;
+	void __iomem *doorbell_area;
+	u32 doorbell_area_size;
+
+	u32 msg_enable;
+
+	/* Page for Shadow Registers */
+	void *rx_ring_shadow_reg_area;
+	dma_addr_t rx_ring_shadow_reg_dma;
+	void *tx_ring_shadow_reg_area;
+	dma_addr_t tx_ring_shadow_reg_dma;
+
+	u32 mailbox_in;
+	u32 mailbox_out;
+
+	int tx_ring_size;
+	int rx_ring_size;
+	u32 intr_count;
+	struct msix_entry *msi_x_entry;
+	struct intr_context intr_context[MAX_RX_RINGS];
+
+	int (*legacy_check) (struct ql_adapter *);
+
+	int tx_ring_count;	/* One per online CPU. */
+	u32 rss_ring_first_cq_id;/* index of first inbound (rss) rx_ring */
+	u32 rss_ring_count;	/* One per online CPU.  */
+	/*
+	 * rx_ring_count =
+	 *  one default queue +
+	 *  (CPU count * outbound completion rx_ring) +
+	 *  (CPU count * inbound (RSS) completion rx_ring)
+	 */
+	int rx_ring_count;
+	int ring_mem_size;
+	void *ring_mem;
+	struct rx_ring *rx_ring;
+	int rx_csum;
+	struct tx_ring *tx_ring;
+	u32 default_rx_queue;
+
+	u16 rx_coalesce_usecs;	/* cqicb->int_delay */
+	u16 rx_max_coalesced_frames;	/* cqicb->pkt_int_delay */
+	u16 tx_coalesce_usecs;	/* cqicb->int_delay */
+	u16 tx_max_coalesced_frames;	/* cqicb->pkt_int_delay */
+
+	u32 xg_sem_mask;
+	u32 port_link_up;
+	u32 port_init;
+	u32 link_status;
+
+	struct net_device_stats stats;
+	struct workqueue_struct *q_workqueue;
+	struct workqueue_struct *workqueue;
+	struct delayed_work asic_reset_work;
+	struct delayed_work mpi_reset_work;
+	struct delayed_work mpi_work;
+};
+
+/*
+ * Typical Register accessor for memory mapped device.
+ */
+static inline u32 ql_read32(const struct ql_adapter *qdev, int reg)
+{
+	return readl(qdev->reg_base + reg);
+}
+
+/*
+ * Typical Register accessor for memory mapped device.
+ */
+static inline void ql_write32(const struct ql_adapter *qdev, int reg, u32 val)
+{
+	writel(val, qdev->reg_base + reg);
+}
+
+/*
+ * Doorbell Registers:
+ * Doorbell registers are virtual registers in the PCI memory space.
+ * The space is allocated by the chip during PCI initialization.  The
+ * device driver finds the doorbell address in BAR 3 in PCI config space.
+ * The registers are used to control outbound and inbound queues. For
+ * example, the producer index for an outbound queue.  Each queue uses
+ * 1 4k chunk of memory.  The lower half of the space is for outbound
+ * queues. The upper half is for inbound queues.
+ */
+static inline void ql_write_db_reg(u32 val, void __iomem *addr)
+{
+	writel(val, addr);
+	mmiowb();
+}
+
+/*
+ * Shadow Registers:
+ * Outbound queues have a consumer index that is maintained by the chip.
+ * Inbound queues have a producer index that is maintained by the chip.
+ * For lower overhead, these registers are "shadowed" to host memory
+ * which allows the device driver to track the queue progress without
+ * PCI reads. When an entry is placed on an inbound queue, the chip will
+ * update the relevant index register and then copy the value to the
+ * shadow register in host memory.
+ */
+static inline unsigned int ql_read_sh_reg(const volatile void  *addr)
+{
+	return *(volatile unsigned int __force *)addr;
+}
+
+extern char qlge_driver_name[];
+extern const char qlge_driver_version[];
+extern const struct ethtool_ops qlge_ethtool_ops;
+
+extern int ql_sem_spinlock(struct ql_adapter *qdev, u32 sem_mask);
+extern void ql_sem_unlock(struct ql_adapter *qdev, u32 sem_mask);
+extern int ql_read_xgmac_reg(struct ql_adapter *qdev, u32 reg, u32 *data);
+extern int ql_get_mac_addr_reg(struct ql_adapter *qdev, u32 type, u16 index,
+			       u32 *value);
+extern int ql_get_routing_reg(struct ql_adapter *qdev, u32 index, u32 *value);
+extern int ql_write_cfg(struct ql_adapter *qdev, void *ptr, int size, u32 bit,
+			u16 q_id);
+void ql_mpi_work(struct work_struct *work);
+void ql_mpi_reset_work(struct work_struct *work);
+int ql_wait_addr_reg(struct ql_adapter *qdev, u32 reg, u32 bit);
+void ql_queue_asic_error(struct ql_adapter *qdev);
+void ql_enable_completion_interrupt(struct ql_adapter *qdev, u32 intr);
+void ql_set_ethtool_ops(struct net_device *ndev);
+int ql_read_xgmac_reg64(struct ql_adapter *qdev, u32 reg, u64 *data);
+
+#if 1
+#define QL_ALL_DUMP
+#define QL_REG_DUMP
+#define QL_DEV_DUMP
+#define QL_CB_DUMP
+/* #define QL_IB_DUMP */
+/* #define QL_OB_DUMP */
+#endif
+
+#ifdef QL_REG_DUMP
+extern void ql_dump_xgmac_control_regs(struct ql_adapter *qdev);
+extern void ql_dump_routing_entries(struct ql_adapter *qdev);
+extern void ql_dump_regs(struct ql_adapter *qdev);
+#define QL_DUMP_REGS(qdev) ql_dump_regs(qdev)
+#define QL_DUMP_ROUTE(qdev) ql_dump_routing_entries(qdev)
+#define QL_DUMP_XGMAC_CONTROL_REGS(qdev) ql_dump_xgmac_control_regs(qdev)
+#else
+#define QL_DUMP_REGS(qdev)
+#define QL_DUMP_ROUTE(qdev)
+#define QL_DUMP_XGMAC_CONTROL_REGS(qdev)
+#endif
+
+#ifdef QL_STAT_DUMP
+extern void ql_dump_stat(struct ql_adapter *qdev);
+#define QL_DUMP_STAT(qdev) ql_dump_stat(qdev)
+#else
+#define QL_DUMP_STAT(qdev)
+#endif
+
+#ifdef QL_DEV_DUMP
+extern void ql_dump_qdev(struct ql_adapter *qdev);
+#define QL_DUMP_QDEV(qdev) ql_dump_qdev(qdev)
+#else
+#define QL_DUMP_QDEV(qdev)
+#endif
+
+#ifdef QL_CB_DUMP
+extern void ql_dump_wqicb(struct wqicb *wqicb);
+extern void ql_dump_tx_ring(struct tx_ring *tx_ring);
+extern void ql_dump_ricb(struct ricb *ricb);
+extern void ql_dump_cqicb(struct cqicb *cqicb);
+extern void ql_dump_rx_ring(struct rx_ring *rx_ring);
+extern void ql_dump_hw_cb(struct ql_adapter *qdev, int size, u32 bit, u16 q_id);
+#define QL_DUMP_RICB(ricb) ql_dump_ricb(ricb)
+#define QL_DUMP_WQICB(wqicb) ql_dump_wqicb(wqicb)
+#define QL_DUMP_TX_RING(tx_ring) ql_dump_tx_ring(tx_ring)
+#define QL_DUMP_CQICB(cqicb) ql_dump_cqicb(cqicb)
+#define QL_DUMP_RX_RING(rx_ring) ql_dump_rx_ring(rx_ring)
+#define QL_DUMP_HW_CB(qdev, size, bit, q_id) \
+		ql_dump_hw_cb(qdev, size, bit, q_id)
+#else
+#define QL_DUMP_RICB(ricb)
+#define QL_DUMP_WQICB(wqicb)
+#define QL_DUMP_TX_RING(tx_ring)
+#define QL_DUMP_CQICB(cqicb)
+#define QL_DUMP_RX_RING(rx_ring)
+#define QL_DUMP_HW_CB(qdev, size, bit, q_id)
+#endif
+
+#ifdef QL_OB_DUMP
+extern void ql_dump_tx_desc(struct tx_buf_desc *tbd);
+extern void ql_dump_ob_mac_iocb(struct ob_mac_iocb_req *ob_mac_iocb);
+extern void ql_dump_ob_mac_rsp(struct ob_mac_iocb_rsp *ob_mac_rsp);
+#define QL_DUMP_OB_MAC_IOCB(ob_mac_iocb) ql_dump_ob_mac_iocb(ob_mac_iocb)
+#define QL_DUMP_OB_MAC_RSP(ob_mac_rsp) ql_dump_ob_mac_rsp(ob_mac_rsp)
+#else
+#define QL_DUMP_OB_MAC_IOCB(ob_mac_iocb)
+#define QL_DUMP_OB_MAC_RSP(ob_mac_rsp)
+#endif
+
+#ifdef QL_IB_DUMP
+extern void ql_dump_ib_mac_rsp(struct ib_mac_iocb_rsp *ib_mac_rsp);
+#define QL_DUMP_IB_MAC_RSP(ib_mac_rsp) ql_dump_ib_mac_rsp(ib_mac_rsp)
+#else
+#define QL_DUMP_IB_MAC_RSP(ib_mac_rsp)
+#endif
+
+#ifdef	QL_ALL_DUMP
+extern void ql_dump_all(struct ql_adapter *qdev);
+#define QL_DUMP_ALL(qdev) ql_dump_all(qdev)
+#else
+#define QL_DUMP_ALL(qdev)
+#endif
+
+#endif /* _QLGE_H_ */
-- 
1.5.0.rc4.16.g9e258

[PATCH 5/8] [RFC] qlge: Add main source module qlge_main.c

[Ron Mercer]

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
---
 drivers/net/qlge/qlge_main.c | 4004 ++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 4004 insertions(+), 0 deletions(-)
 create mode 100755 drivers/net/qlge/qlge_main.c

diff --git a/drivers/net/qlge/qlge_main.c b/drivers/net/qlge/qlge_main.c
new file mode 100755
index 0000000..0b0264c
--- /dev/null
+++ b/drivers/net/qlge/qlge_main.c
@@ -0,0 +1,4004 @@
+/*
+ * QLogic qlge NIC HBA Driver
+ * Copyright (c)  2003-2008 QLogic Corporation
+ * See LICENSE.qlge for copyright and licensing details.
+ * Author:     Linux qlge network device driver by
+ *                      Ron Mercer <ron.mercer@qlogic.com>
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/list.h>
+#include <linux/pci.h>
+#include <linux/dma-mapping.h>
+#include <linux/pagemap.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/dmapool.h>
+#include <linux/mempool.h>
+#include <linux/spinlock.h>
+#include <linux/kthread.h>
+#include <linux/interrupt.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/in.h>
+#include <linux/ip.h>
+#include <linux/ipv6.h>
+#include <net/ipv6.h>
+#include <linux/tcp.h>
+#include <linux/udp.h>
+#include <linux/if_arp.h>
+#include <linux/if_ether.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/skbuff.h>
+#include <linux/rtnetlink.h>
+#include <linux/if_vlan.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/mm.h>
+#include <linux/vmalloc.h>
+
+#include "qlge.h"
+
+char qlge_driver_name[] = DRV_NAME;
+const char qlge_driver_version[] = DRV_VERSION;
+
+MODULE_AUTHOR("Ron Mercer <ron.mercer@qlogic.com>");
+MODULE_DESCRIPTION(DRV_STRING " ");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_VERSION);
+
+static const u32 default_msg =
+    NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK |
+/* NETIF_MSG_TIMER |	*/
+    NETIF_MSG_IFDOWN |
+    NETIF_MSG_IFUP |
+    NETIF_MSG_RX_ERR |
+    NETIF_MSG_TX_ERR |
+    NETIF_MSG_TX_QUEUED |
+    NETIF_MSG_INTR | NETIF_MSG_TX_DONE | NETIF_MSG_RX_STATUS |
+/* NETIF_MSG_PKTDATA | */
+    NETIF_MSG_HW | NETIF_MSG_WOL | 0;
+
+static int debug = 0x00007fff;	/* defaults above */
+module_param(debug, int, 0);
+MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
+
+#define MSIX_IRQ 0
+#define MSI_IRQ 1
+#define LEG_IRQ 2
+static int irq_type = MSIX_IRQ;
+module_param(irq_type, int, MSIX_IRQ);
+MODULE_PARM_DESC(irq_type, "0 = MSI-X, 1 = MSI, 2 = Legacy.");
+
+static struct pci_device_id qlge_pci_tbl[] __devinitdata = {
+	{PCI_DEVICE(PCI_VENDOR_ID_QLOGIC, QLGE_DEVICE_ID)},
+	{PCI_DEVICE(PCI_VENDOR_ID_QLOGIC, QLGE_DEVICE_ID1)},
+	/* required last entry */
+	{0,}
+};
+
+MODULE_DEVICE_TABLE(pci, qlge_pci_tbl);
+
+/* This hardware semaphore causes exclusive access to
+ * resources shared between the NIC driver, MPI firmware,
+ * FCOE firmware and the FC driver.
+ */
+static int ql_sem_trylock(struct ql_adapter *qdev, u32 sem_mask)
+{
+	u32 sem_bits = 0;
+
+	switch (sem_mask) {
+	case SEM_XGMAC0_MASK:
+		sem_bits = SEM_SET << SEM_XGMAC0_SHIFT;
+		break;
+	case SEM_XGMAC1_MASK:
+		sem_bits = SEM_SET << SEM_XGMAC1_SHIFT;
+		break;
+	case SEM_ICB_MASK:
+		sem_bits = SEM_SET << SEM_ICB_SHIFT;
+		break;
+	case SEM_MAC_ADDR_MASK:
+		sem_bits = SEM_SET << SEM_MAC_ADDR_SHIFT;
+		break;
+	case SEM_FLASH_MASK:
+		sem_bits = SEM_SET << SEM_FLASH_SHIFT;
+		break;
+	case SEM_PROBE_MASK:
+		sem_bits = SEM_SET << SEM_PROBE_SHIFT;
+		break;
+	case SEM_RT_IDX_MASK:
+		sem_bits = SEM_SET << SEM_RT_IDX_SHIFT;
+		break;
+	case SEM_PROC_REG_MASK:
+		sem_bits = SEM_SET << SEM_PROC_REG_SHIFT;
+		break;
+	default:
+		QPRINTK(qdev, PROBE, ALERT, "Bad Semaphore mask!.\n");
+		return -EINVAL;
+	}
+
+	ql_write32(qdev, SEM, sem_bits | sem_mask);
+	return !(ql_read32(qdev, SEM) & sem_bits);
+}
+
+int ql_sem_spinlock(struct ql_adapter *qdev, u32 sem_mask)
+{
+	unsigned int seconds = 3;
+	do {
+		if (!ql_sem_trylock(qdev, sem_mask))
+			return 0;
+		ssleep(1);
+	} while (--seconds);
+	return -ETIMEDOUT;
+}
+
+void ql_sem_unlock(struct ql_adapter *qdev, u32 sem_mask)
+{
+	ql_write32(qdev, SEM, sem_mask);
+	ql_read32(qdev, SEM);	/* flush */
+}
+
+/* If the initialization process finds that another function
+ * or firmware module is bring up the port then it calls this
+ * to wait until the process is complete.
+ * Returns zero on success.
+ */
+static int ql_wait_port_init_cmplt(struct ql_adapter *qdev)
+{
+	int count = 100;
+	u32 temp;
+
+	while (count) {
+		temp = ql_read32(qdev, STS);
+		if (temp & qdev->port_init)
+			return 0;
+		mdelay(5);
+		QPRINTK(qdev, LINK, INFO, "Wait for MAC Port to Initialize.\n");
+		count--;
+	}
+	return -ETIMEDOUT;
+}
+
+/* The CFG register is used to download TX and RX control blocks
+ * to the chip. This function waits for an operation to complete.
+ */
+static int ql_wait_cfg(struct ql_adapter *qdev, u32 bit)
+{
+	int count = MSLEEP_COUNT;
+	u32 temp;
+
+	while (count) {
+		temp = ql_read32(qdev, CFG);
+		if (!(temp & bit))
+			return 0;
+		if (temp & CFG_LE)
+			return -EIO;
+		spin_unlock(&qdev->hw_lock);
+		msleep(MSLEEP_DELAY);
+		spin_lock(&qdev->hw_lock);
+		count--;
+	}
+	return -ETIMEDOUT;
+}
+
+/* Used to issue init control blocks to hw. Maps control block,
+ * sets address, triggers download, waits for completion.
+ */
+int ql_write_cfg(struct ql_adapter *qdev, void *ptr, int size, u32 bit,
+		 u16 q_id)
+{
+	u64 map;
+	int status = 0;
+	int direction;
+	u32 mask;
+	u32 value;
+
+	direction =
+	    (bit & (CFG_LRQ | CFG_LR | CFG_LCQ)) ? PCI_DMA_TODEVICE :
+	    PCI_DMA_FROMDEVICE;
+
+	map = pci_map_single(qdev->pdev, ptr, size, direction);
+	if (pci_dma_mapping_error(map)) {
+		QPRINTK(qdev, IFUP, ERR, "Couldn't map DMA area.\n");
+		return -ENOMEM;
+	}
+
+	status = ql_wait_cfg(qdev, bit);
+	if (status) {
+		QPRINTK(qdev, IFUP, ERR,
+			"Timed out waiting for CFG to come ready.\n");
+		goto exit;
+	}
+
+	status = ql_sem_spinlock(qdev, SEM_ICB_MASK);
+	if (status)
+		goto exit;
+	ql_write32(qdev, ICB_L, (u32) map);
+	ql_write32(qdev, ICB_H, (u32) (map >> 32));
+	ql_sem_unlock(qdev, SEM_ICB_MASK);	/* does flush too */
+
+	mask = CFG_Q_MASK | (bit << 16);
+	value = bit | (q_id << CFG_Q_SHIFT);
+	ql_write32(qdev, CFG, (mask | value));
+
+	/*
+	 * Wait for the bit to clear after signaling hw.
+	 */
+	status = ql_wait_cfg(qdev, bit);
+exit:
+	pci_unmap_single(qdev->pdev, map, size, direction);
+	return status;
+}
+
+/* This chip has several addr/data register pairs that are used
+ * to index into another set of registers.  This function waits
+ * for a specified register set to be ready for access.
+ * Examples would be setting up the CAM with MAC addresses, setting
+ * up the frame routing table.
+ */
+static int ql_wait_idx_reg(struct ql_adapter *qdev, u32 reg, u32 flag)
+{
+	int count = 200;
+	u32 temp;
+
+	while (count) {
+		temp = ql_read32(qdev, reg);
+		if (temp & flag)
+			return 0;
+		mdelay(5);
+		count--;
+	}
+	return -ETIMEDOUT;
+}
+
+/* Get a specific MAC address from the CAM.  Used for debug and reg dump. */
+int ql_get_mac_addr_reg(struct ql_adapter *qdev, u32 type, u16 index,
+			u32 *value)
+{
+	u32 offset = 0;
+	int status;
+
+	status = ql_sem_spinlock(qdev, SEM_MAC_ADDR_MASK);
+	if (status)
+		return status;
+	switch (type) {
+	case MAC_ADDR_TYPE_MULTI_MAC:
+	case MAC_ADDR_TYPE_CAM_MAC:
+		{
+			status =
+			    ql_wait_idx_reg(qdev, MAC_ADDR_IDX, MAC_ADDR_MW);
+			if (status)
+				goto exit;
+			ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */
+				   (index << MAC_ADDR_IDX_SHIFT) | /* index */
+				   MAC_ADDR_ADR | MAC_ADDR_RS | type); /* type */
+			status =
+			    ql_wait_idx_reg(qdev, MAC_ADDR_IDX, MAC_ADDR_MR);
+			if (status)
+				goto exit;
+			*value++ = ql_read32(qdev, MAC_ADDR_DATA);
+			status =
+			    ql_wait_idx_reg(qdev, MAC_ADDR_IDX, MAC_ADDR_MW);
+			if (status)
+				goto exit;
+			ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */
+				   (index << MAC_ADDR_IDX_SHIFT) | /* index */
+				   MAC_ADDR_ADR | MAC_ADDR_RS | type); /* type */
+			status =
+			    ql_wait_idx_reg(qdev, MAC_ADDR_IDX, MAC_ADDR_MR);
+			if (status)
+				goto exit;
+			*value++ = ql_read32(qdev, MAC_ADDR_DATA);
+			if (type == MAC_ADDR_TYPE_CAM_MAC) {
+				status =
+				    ql_wait_idx_reg(qdev, MAC_ADDR_IDX,
+						    MAC_ADDR_MW);
+				if (status)
+					goto exit;
+				ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */
+					   (index << MAC_ADDR_IDX_SHIFT) | /* index */
+					   MAC_ADDR_ADR | MAC_ADDR_RS | type); /* type */
+				status =
+				    ql_wait_idx_reg(qdev, MAC_ADDR_IDX,
+						    MAC_ADDR_MR);
+				if (status)
+					goto exit;
+				*value++ = ql_read32(qdev, MAC_ADDR_DATA);
+			}
+			break;
+		}
+	case MAC_ADDR_TYPE_VLAN:
+	case MAC_ADDR_TYPE_MULTI_FLTR:
+	default:
+		QPRINTK(qdev, IFUP, CRIT,
+			"Address type %d not yet supported.\n", type);
+		status = -EPERM;
+	}
+exit:
+	ql_sem_unlock(qdev, SEM_MAC_ADDR_MASK);
+	return status;
+}
+
+/* Set up a MAC, multicast or VLAN address for the
+ * inbound frame matching.
+ */
+static int ql_set_mac_addr_reg(struct ql_adapter *qdev, u8 *addr, u32 type,
+			       u16 index)
+{
+	u32 offset = 0;
+	int status = 0;
+
+	status = ql_sem_spinlock(qdev, SEM_MAC_ADDR_MASK);
+	if (status)
+		return status;
+	switch (type) {
+	case MAC_ADDR_TYPE_MULTI_MAC:
+	case MAC_ADDR_TYPE_CAM_MAC:
+		{
+			u32 cam_output;
+			u32 upper = (addr[0] << 8) | addr[1];
+			u32 lower =
+			    (addr[2] << 24) | (addr[3] << 16) | (addr[4] << 8) |
+			    (addr[5]);
+
+			QPRINTK(qdev, IFUP, INFO,
+				"Adding %s address %02x:%02x:%02x:%02x:%02x:%02x"
+				" at index %d in the CAM.\n",
+				((type ==
+				  MAC_ADDR_TYPE_MULTI_MAC) ? "MULTICAST" :
+				 "UNICAST"), addr[0], addr[1], addr[2], addr[3],
+				addr[4], addr[5], index);
+
+			status =
+			    ql_wait_idx_reg(qdev, MAC_ADDR_IDX, MAC_ADDR_MW);
+			if (status)
+				goto exit;
+			ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */
+				   (index << MAC_ADDR_IDX_SHIFT) | /* index */
+				   type);	/* type */
+			ql_write32(qdev, MAC_ADDR_DATA, lower);
+			status =
+			    ql_wait_idx_reg(qdev, MAC_ADDR_IDX, MAC_ADDR_MW);
+			if (status)
+				goto exit;
+			ql_write32(qdev, MAC_ADDR_IDX, (offset++) | /* offset */
+				   (index << MAC_ADDR_IDX_SHIFT) | /* index */
+				   type);	/* type */
+			ql_write32(qdev, MAC_ADDR_DATA, upper);
+			status =
+			    ql_wait_idx_reg(qdev, MAC_ADDR_IDX, MAC_ADDR_MW);
+			if (status)
+				goto exit;
+			ql_write32(qdev, MAC_ADDR_IDX, (offset) |	/* offset */
+				   (index << MAC_ADDR_IDX_SHIFT) |	/* index */
+				   type);	/* type */
+			/* This field should also include the queue id
+			   and possibly the function id.  Right now we hardcode
+			   the route field to NIC core.
+			 */
+			if (type == MAC_ADDR_TYPE_CAM_MAC) {
+				cam_output = (CAM_OUT_ROUTE_NIC |
+					      (qdev->
+					       func << CAM_OUT_FUNC_SHIFT) |
+					      (qdev->
+					       rss_ring_first_cq_id <<
+					       CAM_OUT_CQ_ID_SHIFT));
+				if (qdev->vlgrp)
+					cam_output |= CAM_OUT_RV;
+				/* route to NIC core */
+				ql_write32(qdev, MAC_ADDR_DATA, cam_output);
+			}
+			break;
+		}
+	case MAC_ADDR_TYPE_VLAN:
+		{
+			u32 enable_bit = *((u32 *) &addr[0]);
+			/* For VLAN, the addr actually holds a bit that
+			 * either enables or disables the vlan id we are
+			 * addressing. It's either MAC_ADDR_E on or off.
+			 * That's bit-27 we're talking about.
+			 */
+			QPRINTK(qdev, IFUP, INFO, "%s VLAN ID %d %s the CAM.\n",
+				(enable_bit ? "Adding" : "Removing"),
+				index, (enable_bit ? "to" : "from"));
+
+			status =
+			    ql_wait_idx_reg(qdev, MAC_ADDR_IDX, MAC_ADDR_MW);
+			if (status)
+				goto exit;
+			ql_write32(qdev, MAC_ADDR_IDX, offset |	/* offset */
+				   (index << MAC_ADDR_IDX_SHIFT) |	/* index */
+				   type |	/* type */
+				   enable_bit);	/* enable/disable */
+			break;
+		}
+	case MAC_ADDR_TYPE_MULTI_FLTR:
+	default:
+		QPRINTK(qdev, IFUP, CRIT,
+			"Address type %d not yet supported.\n", type);
+		status = -EPERM;
+	}
+exit:
+	ql_sem_unlock(qdev, SEM_MAC_ADDR_MASK);
+	return status;
+}
+
+/* Get a specific frame routing value from the CAM.
+ * Used for debug and reg dump.
+ */
+int ql_get_routing_reg(struct ql_adapter *qdev, u32 index, u32 *value)
+{
+	int status = 0;
+
+	status = ql_sem_spinlock(qdev, SEM_RT_IDX_MASK);
+	if (status)
+		goto exit;
+
+	status = ql_wait_idx_reg(qdev, RT_IDX, RT_IDX_MW);
+	if (status)
+		goto exit;
+
+	ql_write32(qdev, RT_IDX,
+		   RT_IDX_TYPE_NICQ | RT_IDX_RS | (index << RT_IDX_IDX_SHIFT));
+	status = ql_wait_idx_reg(qdev, RT_IDX, RT_IDX_MR);
+	if (status)
+		goto exit;
+	*value = ql_read32(qdev, RT_DATA);
+exit:
+	ql_sem_unlock(qdev, SEM_RT_IDX_MASK);
+	return status;
+}
+
+/* The NIC function for this chip has 16 routing indexes.  Each one can be used
+ * to route different frame types to various inbound queues.  We send broadcast/
+ * multicast/error frames to the default queue for slow handling,
+ * and CAM hit/RSS frames to the fast handling queues.
+ */
+static int ql_set_routing_reg(struct ql_adapter *qdev, u32 index, u32 mask,
+			      int enable)
+{
+	int status;
+	u32 value = 0;
+
+	status = ql_sem_spinlock(qdev, SEM_RT_IDX_MASK);
+	if (status)
+		return status;
+
+	QPRINTK(qdev, IFUP, DEBUG,
+		"%s %s%s%s%s%s%s%s%s%s%s%s%s%s%s%s%s mask %s the routing reg.\n",
+		(enable ? "Adding" : "Removing"),
+		((index == RT_IDX_ALL_ERR_SLOT) ? "MAC ERROR/ALL ERROR" : ""),
+		((index == RT_IDX_IP_CSUM_ERR_SLOT) ? "IP CSUM ERROR" : ""),
+		((index ==
+		  RT_IDX_TCP_UDP_CSUM_ERR_SLOT) ? "TCP/UDP CSUM ERROR" : ""),
+		((index == RT_IDX_BCAST_SLOT) ? "BROADCAST" : ""),
+		((index == RT_IDX_MCAST_MATCH_SLOT) ? "MULTICAST MATCH" : ""),
+		((index == RT_IDX_ALLMULTI_SLOT) ? "ALL MULTICAST MATCH" : ""),
+		((index == RT_IDX_UNUSED6_SLOT) ? "UNUSED6" : ""),
+		((index == RT_IDX_UNUSED7_SLOT) ? "UNUSED7" : ""),
+		((index == RT_IDX_RSS_MATCH_SLOT) ? "RSS ALL/IPV4 MATCH" : ""),
+		((index == RT_IDX_RSS_IPV6_SLOT) ? "RSS IPV6" : ""),
+		((index == RT_IDX_RSS_TCP4_SLOT) ? "RSS TCP4" : ""),
+		((index == RT_IDX_RSS_TCP6_SLOT) ? "RSS TCP6" : ""),
+		((index == RT_IDX_CAM_HIT_SLOT) ? "CAM HIT" : ""),
+		((index == RT_IDX_UNUSED013) ? "UNUSED13" : ""),
+		((index == RT_IDX_UNUSED014) ? "UNUSED14" : ""),
+		((index == RT_IDX_PROMISCUOUS_SLOT) ? "PROMISCUOUS" : ""),
+		(enable ? "to" : "from"));
+
+	switch (mask) {
+	case RT_IDX_CAM_HIT:
+		{
+			value = RT_IDX_DST_CAM_Q |	/* dest */
+			    RT_IDX_TYPE_NICQ |	/* type */
+			    (RT_IDX_CAM_HIT_SLOT << RT_IDX_IDX_SHIFT);/* index */
+			break;
+		}
+	case RT_IDX_VALID:	/* Promiscuous Mode frames. */
+		{
+			value = RT_IDX_DST_DFLT_Q |	/* dest */
+			    RT_IDX_TYPE_NICQ |	/* type */
+			    (RT_IDX_PROMISCUOUS_SLOT << RT_IDX_IDX_SHIFT);/* index */
+			break;
+		}
+	case RT_IDX_ERR:	/* Pass up MAC,IP,TCP/UDP error frames. */
+		{
+			value = RT_IDX_DST_DFLT_Q |	/* dest */
+			    RT_IDX_TYPE_NICQ |	/* type */
+			    (RT_IDX_ALL_ERR_SLOT << RT_IDX_IDX_SHIFT);/* index */
+			break;
+		}
+	case RT_IDX_BCAST:	/* Pass up Broadcast frames to default Q. */
+		{
+			value = RT_IDX_DST_DFLT_Q |	/* dest */
+			    RT_IDX_TYPE_NICQ |	/* type */
+			    (RT_IDX_BCAST_SLOT << RT_IDX_IDX_SHIFT);/* index */
+			break;
+		}
+	case RT_IDX_MCAST:	/* Pass up All Multicast frames. */
+		{
+			value = RT_IDX_DST_CAM_Q |	/* dest */
+			    RT_IDX_TYPE_NICQ |	/* type */
+			    (RT_IDX_ALLMULTI_SLOT << RT_IDX_IDX_SHIFT);/* index */
+			break;
+		}
+	case RT_IDX_MCAST_MATCH:	/* Pass up matched Multicast frames. */
+		{
+			value = RT_IDX_DST_CAM_Q |	/* dest */
+			    RT_IDX_TYPE_NICQ |	/* type */
+			    (RT_IDX_MCAST_MATCH_SLOT << RT_IDX_IDX_SHIFT);/* index */
+			break;
+		}
+	case RT_IDX_RSS_MATCH:	/* Pass up matched RSS frames. */
+		{
+			value = RT_IDX_DST_RSS |	/* dest */
+			    RT_IDX_TYPE_NICQ |	/* type */
+			    (RT_IDX_RSS_MATCH_SLOT << RT_IDX_IDX_SHIFT);/* index */
+			break;
+		}
+	case 0:		/* Clear the E-bit on an entry. */
+		{
+			value = RT_IDX_DST_DFLT_Q |	/* dest */
+			    RT_IDX_TYPE_NICQ |	/* type */
+			    (index << RT_IDX_IDX_SHIFT);/* index */
+			break;
+		}
+	default:
+		QPRINTK(qdev, IFUP, ERR, "Mask type %d not yet supported.\n",
+			mask);
+		status = -EPERM;
+		goto exit;
+	}
+
+	if (value) {
+		status = ql_wait_idx_reg(qdev, RT_IDX, RT_IDX_MW);
+		if (status)
+			goto exit;
+		value |= (enable ? RT_IDX_E : 0);
+		ql_write32(qdev, RT_IDX, value);
+		ql_write32(qdev, RT_DATA, enable ? mask : 0);
+	}
+exit:
+	ql_sem_unlock(qdev, SEM_RT_IDX_MASK);
+	return status;
+}
+
+static void ql_enable_interrupts(struct ql_adapter *qdev)
+{
+	ql_write32(qdev, INTR_EN, (INTR_EN_EI << 16) | INTR_EN_EI);
+}
+
+static void ql_disable_interrupts(struct ql_adapter *qdev)
+{
+	ql_write32(qdev, INTR_EN, (INTR_EN_EI << 16));
+}
+
+/* If we're running with multiple MSI-X vectors then we enable on the fly.
+ * Otherwise, we may have multiple outstanding workers and don't want to
+ * enable until the last one finishes. In this case, the irq_cnt gets
+ * incremented everytime we queue a worker and decremented everytime
+ * a worker finishes.  Once it hits zero we enable the interrupt.
+ */
+void ql_enable_completion_interrupt(struct ql_adapter *qdev, u32 intr)
+{
+	if (likely(test_bit(QL_MSIX_ENABLED, &qdev->flags)))
+		ql_write32(qdev, INTR_EN,
+			   qdev->intr_context[intr].intr_en_mask);
+	else {
+		if (qdev->legacy_check)
+			spin_lock(&qdev->legacy_lock);
+		if (atomic_dec_and_test(&qdev->intr_context[intr].irq_cnt)) {
+			QPRINTK(qdev, INTR, ERR, "Enabling interrupt %d.\n",
+				intr);
+			ql_write32(qdev, INTR_EN,
+				   qdev->intr_context[intr].intr_en_mask);
+		} else {
+			QPRINTK(qdev, INTR, ERR,
+				"Skip enable, other queue(s) are active.\n");
+		}
+		if (qdev->legacy_check)
+			spin_unlock(&qdev->legacy_lock);
+	}
+}
+
+static u32 ql_disable_completion_interrupt(struct ql_adapter *qdev, u32 intr)
+{
+	u32 var = 0;
+
+	if (likely(test_bit(QL_MSIX_ENABLED, &qdev->flags)))
+		goto exit;
+	else if (!atomic_read(&qdev->intr_context[intr].irq_cnt)) {
+		ql_write32(qdev, INTR_EN,
+			   qdev->intr_context[intr].intr_dis_mask);
+		var = ql_read32(qdev, STS);
+	}
+	atomic_inc(&qdev->intr_context[intr].irq_cnt);
+exit:
+	return var;
+}
+
+static void ql_enable_all_completion_interrupts(struct ql_adapter *qdev)
+{
+	int i;
+	for (i = 0; i < qdev->intr_count; i++) {
+		/* The enable call does a atomic_dec_and_test
+		 * and enables only if the result is zero.
+		 * So we precharge it here.
+		 */
+		atomic_set(&qdev->intr_context[i].irq_cnt, 1);
+		ql_enable_completion_interrupt(qdev, i);
+	}
+
+}
+
+/* This function waits for an address index register to come ready.
+ * It is currenly used by processor, xgmac, and flash address
+ * registers.  Others may need to be added later.
+ */
+int ql_wait_addr_reg(struct ql_adapter *qdev, u32 reg, u32 bit)
+{
+	u32 temp;
+	int count = 20;
+
+	while (count) {
+		temp = ql_read32(qdev, reg);
+
+#ifdef PALLADIUM
+/* Palladium workaround start: */
+		if (temp == -1)
+			continue;
+/* Palladium workaround end: */
+#endif
+
+		/* check for errors */
+		if (temp & ADDR_ERR) {
+			QPRINTK(qdev, PROBE, ALERT,
+				"register 0x%.08x access error, value = 0x%.08x!.\n",
+				reg, temp);
+			return -EIO;
+		} else if (temp & bit) {
+			return 0;
+		} else {
+			mdelay(1);
+			count--;
+		}
+	}
+	QPRINTK(qdev, PROBE, ALERT,
+		"Timed out waiting for reg %x to come ready.\n", reg);
+	return -ETIMEDOUT;
+}
+
+static int ql_get_flash_params(struct ql_adapter *qdev)
+{
+	if (ql_sem_spinlock(qdev, SEM_FLASH_MASK))
+		return -ETIMEDOUT;
+	/* TODO: flash has yet to be defined. */
+	ql_sem_unlock(qdev, SEM_FLASH_MASK);
+	return 0;
+}
+
+/* xgmac register are located behind the xgmac_addr and xgmac_data
+ * register pair.  Each read/write requires us to wait for the ready
+ * bit before reading/writing the data.
+ */
+static int ql_write_xgmac_reg(struct ql_adapter *qdev, u32 reg, u32 data)
+{
+	int status = 0;
+	/* wait for reg to come ready */
+	status = ql_wait_addr_reg(qdev, XGMAC_ADDR, XGMAC_ADDR_RDY);
+	if (status)
+		goto exit;
+	/* write the data to the data reg */
+	ql_write32(qdev, XGMAC_DATA, data);
+	/* trigger the write */
+	ql_write32(qdev, XGMAC_ADDR, reg);
+	/* wait for reg to come ready */
+	status = ql_wait_addr_reg(qdev, XGMAC_ADDR, XGMAC_ADDR_RDY);
+	if (status)
+		goto exit;
+exit:
+	return status;
+}
+
+/* xgmac register are located behind the xgmac_addr and xgmac_data
+ * register pair.  Each read/write requires us to wait for the ready
+ * bit before reading/writing the data.
+ */
+int ql_read_xgmac_reg(struct ql_adapter *qdev, u32 reg, u32 *data)
+{
+	int status = 0;
+	/* wait for reg to come ready */
+	status = ql_wait_addr_reg(qdev, XGMAC_ADDR, XGMAC_ADDR_RDY);
+	if (status)
+		goto exit;
+	/* set up for reg read */
+	ql_write32(qdev, XGMAC_ADDR, reg | XGMAC_ADDR_R);
+	/* wait for reg to come ready */
+	status = ql_wait_addr_reg(qdev, XGMAC_ADDR, XGMAC_ADDR_RDY);
+	if (status)
+		goto exit;
+	/* get the data */
+	*data = ql_read32(qdev, XGMAC_DATA);
+exit:
+	return status;
+}
+
+/* This is used for reading the 64-bit statistics regs. */
+int ql_read_xgmac_reg64(struct ql_adapter *qdev, u32 reg, u64 *data)
+{
+	int status = 0;
+	u32 hi = 0;
+	u32 lo = 0;
+
+	status = ql_read_xgmac_reg(qdev, reg, &lo);
+	if (status)
+		goto exit;
+
+	status = ql_read_xgmac_reg(qdev, reg + 4, &hi);
+	if (status)
+		goto exit;
+
+	*data = (u64) lo | ((u64) hi << 32);
+
+exit:
+	return status;
+}
+
+/* Take the MAC Core out of reset.
+ * Enable statistics counting.
+ * Take the transmitter/receiver out of reset.
+ * This functionality may be done in the MPI firmware at a
+ * later date.
+ */
+static int ql_port_initialize(struct ql_adapter *qdev)
+{
+	int status = 0;
+	u32 data;
+
+	if (ql_sem_trylock(qdev, qdev->xg_sem_mask)) {
+		/* Another function has the semaphore, so
+		 * wait for the port init bit to come ready.
+		 */
+		QPRINTK(qdev, LINK, INFO,
+			"Another function has the semaphore, so wait for the port init bit to come ready.\n");
+		status = ql_wait_port_init_cmplt(qdev);
+		if (status) {
+			QPRINTK(qdev, LINK, CRIT,
+				"Port initialize timed out.\n");
+		}
+		return status;
+	}
+
+	QPRINTK(qdev, LINK, INFO, "Got xgmac semaphore!.\n");
+	/* Set the core reset. */
+	status = ql_read_xgmac_reg(qdev, GLOBAL_CFG, &data);
+	if (status)
+		goto end;
+	data |= GLOBAL_CFG_RESET;
+	status = ql_write_xgmac_reg(qdev, GLOBAL_CFG, data);
+	if (status)
+		goto end;
+
+	mdelay(100);
+
+	/* Clear the core reset and turn on jumbo for receiver. */
+	data &= ~GLOBAL_CFG_RESET;	/* Clear core reset. */
+	data |= GLOBAL_CFG_JUMBO;	/* Turn on jumbo. */
+	data |= GLOBAL_CFG_TX_STAT_EN;
+	data |= GLOBAL_CFG_RX_STAT_EN;
+	status = ql_write_xgmac_reg(qdev, GLOBAL_CFG, data);
+	if (status)
+		goto end;
+
+	/* Enable transmitter, and clear it's reset. */
+	status = ql_read_xgmac_reg(qdev, TX_CFG, &data);
+	if (status)
+		goto end;
+	data &= ~TX_CFG_RESET;	/* Clear the TX MAC reset. */
+	data |= TX_CFG_EN;	/* Enable the transmitter. */
+	status = ql_write_xgmac_reg(qdev, TX_CFG, data);
+	if (status)
+		goto end;
+
+	/* Enable receiver and clear it's reset. */
+	status = ql_read_xgmac_reg(qdev, RX_CFG, &data);
+	if (status)
+		goto end;
+	data &= ~RX_CFG_RESET;	/* Clear the RX MAC reset. */
+	data |= RX_CFG_EN;	/* Enable the receiver. */
+	status = ql_write_xgmac_reg(qdev, RX_CFG, data);
+	if (status)
+		goto end;
+
+	/* Turn on jumbo. */
+	status =
+	    ql_write_xgmac_reg(qdev, MAC_TX_PARAMS, MAC_TX_PARAMS_JUMBO | (0x2580 << 16));
+	if (status)
+		goto end;
+	status =
+	    ql_write_xgmac_reg(qdev, MAC_RX_PARAMS, 0x2580);
+	if (status)
+		goto end;
+
+	/* Signal to the world that the port is enabled.        */
+	ql_write32(qdev, STS, ((qdev->port_init << 16) | qdev->port_init));
+end:
+	ql_sem_unlock(qdev, qdev->xg_sem_mask);
+	return status;
+}
+
+/* Get the next large buffer. */
+struct bq_desc *ql_get_curr_lbuf(struct rx_ring *rx_ring)
+{
+	struct bq_desc *lbq_desc = &rx_ring->lbq[rx_ring->lbq_curr_idx];
+	rx_ring->lbq_curr_idx++;
+	if (rx_ring->lbq_curr_idx == rx_ring->lbq_len)
+		rx_ring->lbq_curr_idx = 0;
+	rx_ring->lbq_free_cnt++;
+	return lbq_desc;
+}
+
+/* Get the next small buffer. */
+struct bq_desc *ql_get_curr_sbuf(struct rx_ring *rx_ring)
+{
+	struct bq_desc *sbq_desc = &rx_ring->sbq[rx_ring->sbq_curr_idx];
+	rx_ring->sbq_curr_idx++;
+	if (rx_ring->sbq_curr_idx == rx_ring->sbq_len)
+		rx_ring->sbq_curr_idx = 0;
+	rx_ring->sbq_free_cnt++;
+	return sbq_desc;
+}
+
+/* Update an rx ring index. */
+static void ql_update_cq(struct rx_ring *rx_ring)
+{
+	rx_ring->cnsmr_idx++;
+	rx_ring->curr_entry++;
+	if (unlikely(rx_ring->cnsmr_idx == rx_ring->cq_len)) {
+		rx_ring->cnsmr_idx = 0;
+		rx_ring->curr_entry = rx_ring->cq_base;
+	}
+}
+
+static void ql_write_cq_idx(struct rx_ring *rx_ring)
+{
+	ql_write_db_reg(rx_ring->cnsmr_idx, rx_ring->cnsmr_idx_db_reg);
+}
+
+/* Process (refill) a large buffer queue. */
+static void ql_update_lbq(struct ql_adapter *qdev, struct rx_ring *rx_ring)
+{
+	int clean_idx = rx_ring->lbq_clean_idx;
+	struct bq_desc *lbq_desc;
+	struct bq_element *bq;
+	u64 map;
+	int i;
+
+	while (rx_ring->lbq_free_cnt > 16) {
+		for (i = 0; i < 16; i++) {
+			QPRINTK(qdev, RX_STATUS, DEBUG,
+				"lbq: try cleaning clean_idx = %d.\n",
+				clean_idx);
+			lbq_desc = &rx_ring->lbq[clean_idx];
+			bq = lbq_desc->bq;
+			if (lbq_desc->p.lbq_page == NULL) {
+				QPRINTK(qdev, RX_STATUS, DEBUG,
+					"lbq: getting new page for index %d.\n",
+					lbq_desc->index);
+				lbq_desc->p.lbq_page = alloc_page(GFP_ATOMIC);
+				if (lbq_desc->p.lbq_page == NULL) {
+					QPRINTK(qdev, RX_STATUS, ERR,
+						"Couldn't get a page.\n");
+					return;
+				}
+				map = pci_map_page(qdev->pdev,
+						   lbq_desc->p.lbq_page,
+						   0, PAGE_SIZE,
+						   PCI_DMA_FROMDEVICE);
+				if (pci_dma_mapping_error(map)) {
+					QPRINTK(qdev, RX_STATUS, ERR,
+						"PCI mapping failed.\n");
+					return;
+				}
+				pci_unmap_addr_set(lbq_desc, mapaddr, map);
+				pci_unmap_len_set(lbq_desc, maplen, PAGE_SIZE);
+				bq->addr_lo =	/*lbq_desc->addr_lo = */
+				    cpu_to_le32(map);
+				bq->addr_hi =	/*lbq_desc->addr_hi = */
+				    cpu_to_le32(map >> 32);
+			}
+			clean_idx++;
+			if (clean_idx == rx_ring->lbq_len)
+				clean_idx = 0;
+		}
+
+		rx_ring->lbq_clean_idx = clean_idx;
+		rx_ring->lbq_prod_idx += 16;
+		if (rx_ring->lbq_prod_idx == rx_ring->lbq_len)
+			rx_ring->lbq_prod_idx = 0;
+		QPRINTK(qdev, RX_STATUS, DEBUG,
+			"lbq: updating prod idx = %d.\n",
+			rx_ring->lbq_prod_idx);
+		ql_write_db_reg(rx_ring->lbq_prod_idx,
+				rx_ring->lbq_prod_idx_db_reg);
+		rx_ring->lbq_free_cnt -= 16;
+	}
+}
+
+/* Process (refill) a small buffer queue. */
+static void ql_update_sbq(struct ql_adapter *qdev, struct rx_ring *rx_ring)
+{
+	int clean_idx = rx_ring->sbq_clean_idx;
+	struct bq_desc *sbq_desc;
+	struct bq_element *bq;
+	u64 map;
+	int i;
+
+	while (rx_ring->sbq_free_cnt > 16) {
+		for (i = 0; i < 16; i++) {
+			sbq_desc = &rx_ring->sbq[clean_idx];
+			QPRINTK(qdev, RX_STATUS, DEBUG,
+				"sbq: try cleaning clean_idx = %d.\n",
+				clean_idx);
+			bq = sbq_desc->bq;
+			if (sbq_desc->p.skb == NULL) {
+				QPRINTK(qdev, RX_STATUS, DEBUG,
+					"sbq: getting new skb for index %d.\n",
+					sbq_desc->index);
+				sbq_desc->p.skb =
+				    netdev_alloc_skb(qdev->ndev,
+						     rx_ring->sbq_buf_size);
+				if (sbq_desc->p.skb == NULL) {
+					QPRINTK(qdev, PROBE, ERR,
+						"Couldn't get an skb.\n");
+					rx_ring->sbq_clean_idx = clean_idx;
+					return;
+				}
+				skb_reserve(sbq_desc->p.skb, QLGE_SB_PAD);
+				map = pci_map_single(qdev->pdev,
+						     sbq_desc->p.skb->data,
+						     rx_ring->sbq_buf_size /
+						     2, PCI_DMA_FROMDEVICE);
+				pci_unmap_addr_set(sbq_desc, mapaddr, map);
+				pci_unmap_len_set(sbq_desc, maplen,
+						  rx_ring->sbq_buf_size / 2);
+				bq->addr_lo = cpu_to_le32(map);
+				bq->addr_hi = cpu_to_le32(map >> 32);
+			}
+
+			clean_idx++;
+			if (clean_idx == rx_ring->sbq_len)
+				clean_idx = 0;
+		}
+		rx_ring->sbq_clean_idx = clean_idx;
+		rx_ring->sbq_prod_idx += 16;
+		if (rx_ring->sbq_prod_idx == rx_ring->sbq_len)
+			rx_ring->sbq_prod_idx = 0;
+		QPRINTK(qdev, RX_STATUS, DEBUG,
+			"sbq: updating prod idx = %d.\n",
+			rx_ring->sbq_prod_idx);
+		ql_write_db_reg(rx_ring->sbq_prod_idx,
+				rx_ring->sbq_prod_idx_db_reg);
+
+		rx_ring->sbq_free_cnt -= 16;
+	}
+}
+
+static void ql_update_buffer_queues(struct ql_adapter *qdev,
+				    struct rx_ring *rx_ring)
+{
+	ql_update_sbq(qdev, rx_ring);
+	ql_update_lbq(qdev, rx_ring);
+}
+
+/* Unmaps tx buffers.  Can be called from send() if a pci mapping
+ * fails at some stage, or from the interrupt when a tx completes.
+ */
+static void ql_unmap_send(struct ql_adapter *qdev,
+			  struct tx_ring_desc *tx_ring_desc, int mapped)
+{
+	int i;
+	for (i = 0; i < mapped; i++) {
+		if (i == 0 || (i == 7 && mapped > 7)) {
+			/*
+			 * Unmap the skb->data area, or the
+			 * external sglist (AKA the Outbound
+			 * Address List (OAL)).
+			 * If its the zeroeth element, then it's
+			 * the skb->data area.  If it's the 7th
+			 * element and there is more than 6 frags,
+			 * then its an OAL.
+			 */
+			if (i == 7) {
+				QPRINTK(qdev, TX_DONE, DEBUG,
+					"unmapping OAL area.\n");
+			}
+			pci_unmap_single(qdev->pdev,
+					 pci_unmap_addr(&tx_ring_desc->map[i],
+							mapaddr),
+					 pci_unmap_len(&tx_ring_desc->map[i],
+						       maplen),
+					 PCI_DMA_TODEVICE);
+		} else {
+			QPRINTK(qdev, TX_DONE, DEBUG, "unmapping frag %d.\n",
+				i);
+			pci_unmap_page(qdev->pdev,
+				       pci_unmap_addr(&tx_ring_desc->map[i],
+						      mapaddr),
+				       pci_unmap_len(&tx_ring_desc->map[i],
+						     maplen), PCI_DMA_TODEVICE);
+		}
+	}
+
+}
+
+/* Map the buffers for this transmit.  This will return
+ * NETDEV_TX_BUSY or NETDEV_TX_OK based on success.
+ */
+static int ql_map_send(struct ql_adapter *qdev,
+		       struct ob_mac_iocb_req *mac_iocb_ptr,
+		       struct sk_buff *skb, struct tx_ring_desc *tx_ring_desc)
+{
+	int len = skb_headlen(skb);
+	dma_addr_t map;
+	int frag_idx, err, map_idx = 0;
+	struct tx_buf_desc *tbd = mac_iocb_ptr->tbd;
+	int frag_cnt = skb_shinfo(skb)->nr_frags;
+
+	if (frag_cnt) {
+		QPRINTK(qdev, TX_QUEUED, DEBUG, "frag_cnt = %d.\n", frag_cnt);
+	}
+	/*
+	 * Map the skb buffer first.
+	 */
+	map = pci_map_single(qdev->pdev, skb->data, len, PCI_DMA_TODEVICE);
+
+	err = pci_dma_mapping_error(map);
+	if (err) {
+		QPRINTK(qdev, TX_QUEUED, ERR,
+			"PCI mapping failed with error: %d\n", err);
+
+		return NETDEV_TX_BUSY;
+	}
+
+	tbd->len = cpu_to_le32(len);
+	tbd->addr = cpu_to_le64(map);
+	pci_unmap_addr_set(&tx_ring_desc->map[map_idx], mapaddr, map);
+	pci_unmap_len_set(&tx_ring_desc->map[map_idx], maplen, len);
+	map_idx++;
+
+	/*
+	 * This loop fills the remainder of the 8 address descriptors
+	 * in the IOCB.  If there are more than 7 fragments, then the
+	 * eighth address desc will point to an external list (OAL).
+	 * When this happens, the remainder of the frags will be stored
+	 * in this list.
+	 */
+	for (frag_idx = 0; frag_idx < frag_cnt; frag_idx++, map_idx++) {
+		skb_frag_t *frag = &skb_shinfo(skb)->frags[frag_idx];
+		tbd++;
+		if (frag_idx == 6 && frag_cnt > 7) {
+			/* Let's tack on an sglist.
+			 * Our control block will now
+			 * look like this:
+			 * iocb->seg[0] = skb->data
+			 * iocb->seg[1] = frag[0]
+			 * iocb->seg[2] = frag[1]
+			 * iocb->seg[3] = frag[2]
+			 * iocb->seg[4] = frag[3]
+			 * iocb->seg[5] = frag[4]
+			 * iocb->seg[6] = frag[5]
+			 * iocb->seg[7] = ptr to OAL (external sglist)
+			 * oal->seg[0] = frag[6]
+			 * oal->seg[1] = frag[7]
+			 * oal->seg[2] = frag[8]
+			 * oal->seg[3] = frag[9]
+			 * oal->seg[4] = frag[10]
+			 *      etc...
+			 */
+			/* Tack on the OAL in the eighth segment of IOCB. */
+			map = pci_map_single(qdev->pdev, &tx_ring_desc->oal,
+					     sizeof(struct oal),
+					     PCI_DMA_TODEVICE);
+			err = pci_dma_mapping_error(map);
+			if (err) {
+				QPRINTK(qdev, TX_QUEUED, ERR,
+					"PCI mapping outbound address list with error: %d\n",
+					err);
+				goto map_error;
+			}
+
+			tbd->addr = cpu_to_le64(map);
+			/*
+			 * The length is the number of fragments
+			 * that remain to be mapped times the length
+			 * of our sglist (OAL).
+			 */
+			tbd->len =
+			    cpu_to_le32((sizeof(struct tx_buf_desc) *
+					 (frag_cnt - frag_idx)) | TX_DESC_C);
+			pci_unmap_addr_set(&tx_ring_desc->map[map_idx], mapaddr,
+					   map);
+			pci_unmap_len_set(&tx_ring_desc->map[map_idx], maplen,
+					  sizeof(struct oal));
+			tbd = (struct tx_buf_desc *)&tx_ring_desc->oal;
+			map_idx++;
+		}
+
+		map =
+		    pci_map_page(qdev->pdev, frag->page,
+				 frag->page_offset, frag->size,
+				 PCI_DMA_TODEVICE);
+
+		err = pci_dma_mapping_error(map);
+		if (err) {
+			QPRINTK(qdev, TX_QUEUED, ERR,
+				"PCI mapping frags failed with error: %d.\n",
+				err);
+			goto map_error;
+		}
+
+		tbd->addr = cpu_to_le64(map);
+		tbd->len = cpu_to_le32(frag->size);
+		pci_unmap_addr_set(&tx_ring_desc->map[map_idx], mapaddr, map);
+		pci_unmap_len_set(&tx_ring_desc->map[map_idx], maplen,
+				  frag->size);
+
+	}
+	/* Save the number of segments we've mapped. */
+	tx_ring_desc->map_cnt = map_idx;
+	/* Terminate the last segment. */
+	tbd->len = cpu_to_le32(le32_to_cpu(tbd->len) | TX_DESC_E);
+	return NETDEV_TX_OK;
+
+map_error:
+	/*
+	 * If the first frag mapping failed, then i will be zero.
+	 * This causes the unmap of the skb->data area.  Otherwise
+	 * we pass in the number of frags that mapped successfully
+	 * so they can be umapped.
+	 */
+	ql_unmap_send(qdev, tx_ring_desc, map_idx);
+	return NETDEV_TX_BUSY;
+}
+
+void ql_realign_skb(struct sk_buff *skb, int len)
+{
+	void *temp_addr = skb->data;
+
+	/* Undo the skb_reserve(skb,32) we did before
+	 * giving to hardware, and realign data on
+	 * a 2-byte boundary.
+	 */
+	skb->data -= QLGE_SB_PAD - NET_IP_ALIGN;
+	skb->tail -= QLGE_SB_PAD - NET_IP_ALIGN;
+	skb_copy_to_linear_data(skb, temp_addr,
+		(unsigned int)len);
+}
+
+/*
+ * This function builds an skb for the given inbound
+ * completion.  It will be rewritten for readability in the near
+ * future, but for not it works well.
+ */
+static struct sk_buff *ql_build_rx_skb(struct ql_adapter *qdev,
+				       struct rx_ring *rx_ring,
+				       struct ib_mac_iocb_rsp *ib_mac_rsp)
+{
+	struct bq_desc *lbq_desc;
+	struct bq_desc *sbq_desc;
+	struct sk_buff *skb = NULL;
+	u32 length = le32_to_cpu(ib_mac_rsp->data_len);
+       u32 hdr_len = le32_to_cpu(ib_mac_rsp->hdr_len);
+
+	/*
+	 * Handle the header buffer if present.
+	 */
+	if (ib_mac_rsp->flags4 & IB_MAC_IOCB_RSP_HV &&
+	    ib_mac_rsp->flags4 & IB_MAC_IOCB_RSP_HS) {
+		QPRINTK(qdev, RX_STATUS, DEBUG, "Header of %d bytes in small buffer.\n", hdr_len);
+		/*
+		 * Headers fit nicely into a small buffer.
+		 */
+		sbq_desc = ql_get_curr_sbuf(rx_ring);
+		pci_unmap_single(qdev->pdev,
+				pci_unmap_addr(sbq_desc, mapaddr),
+				pci_unmap_len(sbq_desc, maplen),
+				PCI_DMA_FROMDEVICE);
+		skb = sbq_desc->p.skb;
+		ql_realign_skb(skb, hdr_len);
+		skb_put(skb, hdr_len);
+		sbq_desc->p.skb = NULL;
+	}
+
+	/*
+	 * Handle the data buffer(s).
+	 */
+	if (unlikely(!length)) {	/* Is there data too? */
+		QPRINTK(qdev, RX_STATUS, DEBUG,
+			"No Data buffer in this packet.\n");
+		return skb;
+	}
+
+	if (ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_DS) {
+		if (ib_mac_rsp->flags4 & IB_MAC_IOCB_RSP_HS) {
+			QPRINTK(qdev, RX_STATUS, DEBUG,
+				"Headers in small, data of %d bytes in small, combine them.\n", length);
+			/*
+			 * Data is less than small buffer size so it's
+			 * stuffed in a small buffer.
+			 * For this case we append the data
+			 * from the "data" small buffer to the "header" small
+			 * buffer.
+			 */
+			sbq_desc = ql_get_curr_sbuf(rx_ring);
+			pci_dma_sync_single_for_cpu(qdev->pdev,
+						    pci_unmap_addr
+						    (sbq_desc, mapaddr),
+						    pci_unmap_len
+						    (sbq_desc, maplen),
+						    PCI_DMA_FROMDEVICE);
+			memcpy(skb_put(skb, length),
+			       sbq_desc->p.skb->data, length);
+			pci_dma_sync_single_for_device(qdev->pdev,
+						       pci_unmap_addr
+						       (sbq_desc,
+							mapaddr),
+						       pci_unmap_len
+						       (sbq_desc,
+							maplen),
+						       PCI_DMA_FROMDEVICE);
+		} else {
+			QPRINTK(qdev, RX_STATUS, DEBUG,
+				"%d bytes in a single small buffer.\n", length);
+			sbq_desc = ql_get_curr_sbuf(rx_ring);
+			skb = sbq_desc->p.skb;
+			ql_realign_skb(skb, length);
+			skb_put(skb, length);
+			pci_unmap_single(qdev->pdev,
+					 pci_unmap_addr(sbq_desc,
+							mapaddr),
+					 pci_unmap_len(sbq_desc,
+						       maplen),
+					 PCI_DMA_FROMDEVICE);
+			sbq_desc->p.skb = NULL;
+		}
+	} else if (ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_DL) {
+		if (ib_mac_rsp->flags4 & IB_MAC_IOCB_RSP_HS) {
+			QPRINTK(qdev, RX_STATUS, DEBUG,
+				"Header in small, %d bytes in large. Chain large to small!\n", length);
+			/*
+			 * The data is in a single large buffer.  We
+			 * chain it to the header buffer's skb and let
+			 * it rip.
+			 */
+			lbq_desc = ql_get_curr_lbuf(rx_ring);
+			pci_unmap_page(qdev->pdev,
+				       pci_unmap_addr(lbq_desc,
+						      mapaddr),
+				       pci_unmap_len(lbq_desc, maplen),
+				       PCI_DMA_FROMDEVICE);
+			QPRINTK(qdev, RX_STATUS, DEBUG,
+				"Chaining page to skb.\n");
+			skb_fill_page_desc(skb, 0, lbq_desc->p.lbq_page,
+					   0, length);
+			skb->len += length;
+			skb->data_len += length;
+			skb->truesize += length;
+			lbq_desc->p.lbq_page = NULL;
+		} else {
+			/*
+			 * The headers and data are in a single large buffer. We
+			 * copy it to a new skb and let it go. This can happen with
+			 * jumbo mtu on a non-TCP/UDP frame.
+			 */
+			lbq_desc = ql_get_curr_lbuf(rx_ring);
+			skb = netdev_alloc_skb(qdev->ndev, length);
+			if (skb == NULL) {
+				QPRINTK(qdev, PROBE, DEBUG,
+					"No skb available, drop the packet.\n");
+				return NULL;
+			}
+			skb_reserve(skb, NET_IP_ALIGN);
+			QPRINTK(qdev, RX_STATUS, DEBUG,
+				"%d bytes of headers and data in large. Chain page to new skb and pull tail.\n", length);
+			skb_fill_page_desc(skb, 0, lbq_desc->p.lbq_page,
+					   0, length);
+			skb->len += length;
+			skb->data_len += length;
+			skb->truesize += length;
+			length -= length;
+			lbq_desc->p.lbq_page = NULL;
+			__pskb_pull_tail(skb,
+				(ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_V) ?
+				VLAN_ETH_HLEN : ETH_HLEN);
+		}
+	} else {
+		/*
+		 * The data is in a chain of large buffers
+		 * pointed to by a small buffer.  We loop
+		 * thru and chain them to the our small header
+		 * buffer's skb.
+		 * frags:  There are 18 max frags and our small
+		 *         buffer will hold 32 of them. The thing is,
+		 *         we'll use 3 max for our 9000 byte jumbo
+		 *         frames.  If the MTU goes up we could
+		 *          eventually be in trouble.
+		 */
+		int size, offset, i = 0;
+		struct bq_element *bq, bq_array[8];
+		sbq_desc = ql_get_curr_sbuf(rx_ring);
+		pci_unmap_single(qdev->pdev,
+				 pci_unmap_addr(sbq_desc, mapaddr),
+				 pci_unmap_len(sbq_desc, maplen),
+				 PCI_DMA_FROMDEVICE);
+		if (!(ib_mac_rsp->flags4 & IB_MAC_IOCB_RSP_HS)) {
+			/*
+			 * This is an non TCP/UDP IP frame, so
+			 * the headers aren't split into a small
+			 * buffer.  We have to use the small buffer
+			 * that contains our sg list as our skb to
+			 * send upstairs. Copy the sg list here to
+			 * a local buffer and use it to find the
+			 * pages to chain.
+			 */
+			QPRINTK(qdev, RX_STATUS, DEBUG,
+				"%d bytes of headers & data in chain of large.\n", length);
+			skb = sbq_desc->p.skb;
+			bq = &bq_array[0];
+			memcpy(bq, skb->data, sizeof(bq_array));
+			sbq_desc->p.skb = NULL;
+			skb_reserve(skb, NET_IP_ALIGN);
+		} else {
+			QPRINTK(qdev, RX_STATUS, DEBUG,
+				"Headers in small, %d bytes of data in chain of large.\n", length);
+			bq = (struct bq_element *)sbq_desc->p.skb->data;
+		}
+		while (length > 0) {
+			lbq_desc = ql_get_curr_lbuf(rx_ring);
+			if ((bq->addr_lo & ~BQ_MASK) != lbq_desc->bq->addr_lo) {
+				QPRINTK(qdev, RX_STATUS, ERR,
+					"Panic!!! bad large buffer address, expected 0x%.08x, got 0x%.08x.\n",
+					lbq_desc->bq->addr_lo, bq->addr_lo);
+				return NULL;
+			}
+			pci_unmap_page(qdev->pdev,
+				       pci_unmap_addr(lbq_desc,
+						      mapaddr),
+				       pci_unmap_len(lbq_desc,
+						     maplen),
+				       PCI_DMA_FROMDEVICE);
+			size = (length < PAGE_SIZE) ? length : PAGE_SIZE;
+			offset = 0;
+
+			QPRINTK(qdev, RX_STATUS, DEBUG,
+				"Adding page %d to skb for %d bytes.\n",
+				i, size);
+			skb_fill_page_desc(skb, i, lbq_desc->p.lbq_page,
+					   offset, size);
+			skb->len += size;
+			skb->data_len += size;
+			skb->truesize += size;
+			length -= size;
+			lbq_desc->p.lbq_page = NULL;
+			bq++;
+			i++;
+		}
+		__pskb_pull_tail(skb, (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_V) ?
+				VLAN_ETH_HLEN : ETH_HLEN);
+	}
+	return skb;
+}
+
+/* Process an inbound completion from an rx ring. */
+static void ql_process_mac_rx_intr(struct ql_adapter *qdev,
+				   struct rx_ring *rx_ring,
+				   struct ib_mac_iocb_rsp *ib_mac_rsp)
+{
+	struct net_device *ndev = qdev->ndev;
+	struct sk_buff *skb = NULL;
+
+	QL_DUMP_IB_MAC_RSP(ib_mac_rsp);
+
+	skb = ql_build_rx_skb(qdev, rx_ring, ib_mac_rsp);
+	if (unlikely(!skb)) {
+		QPRINTK(qdev, RX_STATUS, DEBUG,
+			"No skb available, drop packet.\n");
+		return;
+	}
+
+	prefetch(skb->data);
+	skb->dev = ndev;
+	if (ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_M_MASK) {
+		QPRINTK(qdev, RX_STATUS, DEBUG, "%s%s%s Multicast.\n",
+			(ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_M_MASK) ==
+			IB_MAC_IOCB_RSP_M_HASH ? "Hash" : "",
+			(ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_M_MASK) ==
+			IB_MAC_IOCB_RSP_M_REG ? "Registered" : "",
+			(ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_M_MASK) ==
+			IB_MAC_IOCB_RSP_M_PROM ? "Promiscuous" : "");
+	}
+	if (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_P) {
+		QPRINTK(qdev, RX_STATUS, DEBUG, "Promiscuous Packet.\n");
+	}
+	if (ib_mac_rsp->flags1 & (IB_MAC_IOCB_RSP_IE | IB_MAC_IOCB_RSP_TE)) {
+		QPRINTK(qdev, RX_STATUS, ERR,
+			"Bad checksum for this %s packet.\n",
+			((ib_mac_rsp->
+			  flags2 & IB_MAC_IOCB_RSP_T) ? "TCP" : "UDP"));
+		skb->ip_summed = CHECKSUM_NONE;
+	} else if (qdev->rx_csum &&
+		   ((ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_T) ||
+		    ((ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_U) &&
+		     !(ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_NU)))) {
+		QPRINTK(qdev, RX_STATUS, DEBUG, "RX checksum done!\n");
+		skb->ip_summed = CHECKSUM_UNNECESSARY;
+	}
+	qdev->stats.rx_packets++;
+	qdev->stats.rx_bytes += skb->len;
+	skb->protocol = eth_type_trans(skb, ndev);
+	if (qdev->vlgrp && (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_V)) {
+		QPRINTK(qdev, RX_STATUS, DEBUG,
+			"Passing a VLAN packet upstream.\n");
+		vlan_hwaccel_rx(skb, qdev->vlgrp,
+				le16_to_cpu(ib_mac_rsp->vlan_id));
+	} else {
+		QPRINTK(qdev, RX_STATUS, DEBUG,
+			"Passing a normal packet upstream.\n");
+		netif_rx(skb);
+	}
+	ndev->last_rx = jiffies;
+}
+
+/* Process an outbound completion from an rx ring. */
+static void ql_process_mac_tx_intr(struct ql_adapter *qdev,
+				   struct ob_mac_iocb_rsp *mac_rsp)
+{
+	struct tx_ring *tx_ring;
+	struct tx_ring_desc *tx_ring_desc;
+
+	QL_DUMP_OB_MAC_RSP(mac_rsp);
+	tx_ring = &qdev->tx_ring[mac_rsp->txq_idx];
+	tx_ring_desc = &tx_ring->q[mac_rsp->tid];
+	ql_unmap_send(qdev, tx_ring_desc, tx_ring_desc->map_cnt);
+	qdev->stats.tx_bytes += tx_ring_desc->map_cnt;
+	qdev->stats.tx_packets++;
+	dev_kfree_skb(tx_ring_desc->skb);
+	tx_ring_desc->skb = NULL;
+
+	if (unlikely(mac_rsp->flags1 & (OB_MAC_IOCB_RSP_E |
+					OB_MAC_IOCB_RSP_S |
+					OB_MAC_IOCB_RSP_L |
+					OB_MAC_IOCB_RSP_P | OB_MAC_IOCB_RSP_B))) {
+		if (mac_rsp->flags1 & OB_MAC_IOCB_RSP_E) {
+			QPRINTK(qdev, TX_DONE, WARNING,
+				"Total descriptor length did not match transfer length.\n");
+		}
+		if (mac_rsp->flags1 & OB_MAC_IOCB_RSP_S) {
+			QPRINTK(qdev, TX_DONE, WARNING,
+				"Frame too short to be legal, not sent.\n");
+		}
+		if (mac_rsp->flags1 & OB_MAC_IOCB_RSP_L) {
+			QPRINTK(qdev, TX_DONE, WARNING,
+				"Frame too long, but sent anyway.\n");
+		}
+		if (mac_rsp->flags1 & OB_MAC_IOCB_RSP_B) {
+			QPRINTK(qdev, TX_DONE, WARNING,
+				"PCI backplane error. Frame not sent.\n");
+		}
+	}
+	atomic_inc(&tx_ring->tx_count);
+}
+
+/* Fire up a handler to reset the MPI processor. */
+void ql_queue_fw_error(struct ql_adapter *qdev)
+{
+	netif_stop_queue(qdev->ndev);
+	netif_carrier_off(qdev->ndev);
+	queue_delayed_work(qdev->workqueue, &qdev->mpi_reset_work, 0);
+}
+
+void ql_queue_asic_error(struct ql_adapter *qdev)
+{
+	netif_stop_queue(qdev->ndev);
+	netif_carrier_off(qdev->ndev);
+	ql_disable_interrupts(qdev);
+	queue_delayed_work(qdev->workqueue, &qdev->asic_reset_work, 0);
+}
+
+static void ql_process_chip_ae_intr(struct ql_adapter *qdev,
+				    struct ib_ae_iocb_rsp *ib_ae_rsp)
+{
+	switch (ib_ae_rsp->event) {
+	case MGMT_ERR_EVENT:
+		QPRINTK(qdev, RX_ERR, ERR,
+			"Management Processor Fatal Error.\n");
+		ql_queue_fw_error(qdev);
+		return;
+
+	case CAM_LOOKUP_ERR_EVENT:
+		QPRINTK(qdev, LINK, ERR,
+			"Multiple CAM hits lookup occurred.\n");
+		QPRINTK(qdev, DRV, ERR, "This event shouldn't occur.\n");
+		ql_queue_asic_error(qdev);
+		return;
+
+	case SOFT_ECC_ERROR_EVENT:
+		QPRINTK(qdev, RX_ERR, ERR, "Soft ECC error detected.\n");
+		ql_queue_asic_error(qdev);
+		break;
+
+	case PCI_ERR_ANON_BUF_RD:
+		QPRINTK(qdev, RX_ERR, ERR,
+			"PCI error occurred when reading anonymous buffers from rx_ring %d.\n",
+			ib_ae_rsp->q_id);
+		ql_queue_asic_error(qdev);
+		break;
+
+	default:
+		QPRINTK(qdev, DRV, ERR, "Unexpected event %d.\n",
+			ib_ae_rsp->event);
+		ql_queue_asic_error(qdev);
+		break;
+	}
+}
+
+static int ql_clean_outbound_rx_ring(struct rx_ring *rx_ring)
+{
+	struct ql_adapter *qdev = rx_ring->qdev;
+	u32 prod = ql_read_sh_reg(rx_ring->prod_idx_sh_reg);
+	struct ob_mac_iocb_rsp *net_rsp = NULL;
+	int count = 0;
+
+	/* While there are entries in the completion queue. */
+	while (prod != rx_ring->cnsmr_idx) {
+
+		QPRINTK(qdev, RX_STATUS, DEBUG,
+			"cq_id = %d, prod = %d, cnsmr = %d.\n.", rx_ring->cq_id,
+			prod, rx_ring->cnsmr_idx);
+
+		net_rsp = (struct ob_mac_iocb_rsp *)rx_ring->curr_entry;
+		rmb();
+		switch (net_rsp->opcode) {
+
+		case OPCODE_OB_MAC_TSO_IOCB:
+		case OPCODE_OB_MAC_IOCB:
+			ql_process_mac_tx_intr(qdev, net_rsp);
+			break;
+		default:
+			QPRINTK(qdev, RX_STATUS, DEBUG,
+				"Hit default case, not handled! dropping the packet, opcode = %x.\n",
+				net_rsp->opcode);
+		}
+		count++;
+		ql_update_cq(rx_ring);
+		prod = ql_read_sh_reg(rx_ring->prod_idx_sh_reg);
+	}
+	ql_write_cq_idx(rx_ring);
+	if (netif_queue_stopped(qdev->ndev) && net_rsp != NULL) {
+		struct tx_ring *tx_ring = &qdev->tx_ring[net_rsp->txq_idx];
+		if (atomic_read(&tx_ring->queue_stopped) &&
+		    (atomic_read(&tx_ring->tx_count) > (tx_ring->wq_len / 4)))
+			/*
+			 * The queue got stopped because the tx_ring was full.
+			 * Wake it up, because it's now at least 25% empty.
+			 */
+			netif_wake_queue(qdev->ndev);
+	}
+
+	return count;
+}
+
+static int ql_clean_inbound_rx_ring(struct rx_ring *rx_ring, int budget)
+{
+	struct ql_adapter *qdev = rx_ring->qdev;
+	u32 prod = ql_read_sh_reg(rx_ring->prod_idx_sh_reg);
+	struct ql_net_rsp_iocb *net_rsp;
+	int count = 0;
+
+	/* While there are entries in the completion queue. */
+	while (prod != rx_ring->cnsmr_idx) {
+
+		QPRINTK(qdev, RX_STATUS, DEBUG,
+			"cq_id = %d, prod = %d, cnsmr = %d.\n.", rx_ring->cq_id,
+			prod, rx_ring->cnsmr_idx);
+
+		net_rsp = rx_ring->curr_entry;
+		rmb();
+		switch (net_rsp->opcode) {
+		case OPCODE_IB_MAC_IOCB:
+			ql_process_mac_rx_intr(qdev, rx_ring,
+					       (struct ib_mac_iocb_rsp *)
+					       net_rsp);
+			break;
+
+		case OPCODE_IB_AE_IOCB:
+			ql_process_chip_ae_intr(qdev, (struct ib_ae_iocb_rsp *)
+						net_rsp);
+			break;
+		default:
+			{
+				QPRINTK(qdev, RX_STATUS, DEBUG,
+					"Hit default case, not handled! dropping the packet, opcode = %x.\n",
+					net_rsp->opcode);
+			}
+		}
+		count++;
+		ql_update_cq(rx_ring);
+		prod = ql_read_sh_reg(rx_ring->prod_idx_sh_reg);
+		if (count == budget)
+			break;
+	}
+	ql_update_buffer_queues(qdev, rx_ring);
+	ql_write_cq_idx(rx_ring);
+	return count;
+}
+
+static int ql_napi_poll_msix(struct napi_struct *napi, int budget)
+{
+	struct rx_ring *rx_ring = container_of(napi, struct rx_ring, napi);
+	struct ql_adapter *qdev = rx_ring->qdev;
+	int work_done = ql_clean_inbound_rx_ring(rx_ring, budget);
+
+	QPRINTK(qdev, RX_STATUS, DEBUG, "Enter, NAPI POLL cq_id = %d.\n",
+		rx_ring->cq_id);
+
+	if (work_done < budget) {
+		__netif_rx_complete(qdev->ndev, napi);
+		ql_enable_completion_interrupt(qdev, rx_ring->irq);
+	}
+	return work_done;
+}
+
+static void ql_vlan_rx_register(struct net_device *ndev, struct vlan_group *grp)
+{
+	struct ql_adapter *qdev = netdev_priv(ndev);
+
+	qdev->vlgrp = grp;
+	if (grp) {
+		QPRINTK(qdev, IFUP, DEBUG, "Turning on VLAN in NIC_RCV_CFG.\n");
+		ql_write32(qdev, NIC_RCV_CFG, NIC_RCV_CFG_VLAN_MASK |
+			   NIC_RCV_CFG_VLAN_MATCH_AND_NON);
+	} else {
+		QPRINTK(qdev, IFUP, DEBUG,
+			"Turning off VLAN in NIC_RCV_CFG.\n");
+		ql_write32(qdev, NIC_RCV_CFG, NIC_RCV_CFG_VLAN_MASK);
+	}
+}
+
+static void ql_vlan_rx_add_vid(struct net_device *ndev, u16 vid)
+{
+	struct ql_adapter *qdev = netdev_priv(ndev);
+	u32 enable_bit = MAC_ADDR_E;
+
+	if (ql_set_mac_addr_reg
+	    (qdev, (u8 *) &enable_bit, MAC_ADDR_TYPE_VLAN, vid)) {
+		QPRINTK(qdev, IFUP, ERR, "Failed to init vlan address.\n");
+	}
+}
+
+static void ql_vlan_rx_kill_vid(struct net_device *ndev, u16 vid)
+{
+	struct ql_adapter *qdev = netdev_priv(ndev);
+	u32 enable_bit = 0;
+
+	if (ql_set_mac_addr_reg
+	    (qdev, (u8 *) &enable_bit, MAC_ADDR_TYPE_VLAN, vid)) {
+		QPRINTK(qdev, IFUP, ERR, "Failed to clear vlan address.\n");
+	}
+
+}
+
+/* Worker thread to process a given rx_ring that is dedicated
+ * to outbound completions.
+ */
+static void ql_tx_clean(struct work_struct *work)
+{
+	struct rx_ring *rx_ring =
+	    container_of(work, struct rx_ring, rx_work.work);
+	ql_clean_outbound_rx_ring(rx_ring);
+	ql_enable_completion_interrupt(rx_ring->qdev, rx_ring->irq);
+
+}
+
+/* Worker thread to process a given rx_ring that is dedicated
+ * to inbound completions.
+ */
+static void ql_rx_clean(struct work_struct *work)
+{
+	struct rx_ring *rx_ring =
+	    container_of(work, struct rx_ring, rx_work.work);
+	ql_clean_inbound_rx_ring(rx_ring, 64);
+	ql_enable_completion_interrupt(rx_ring->qdev, rx_ring->irq);
+}
+
+/* MSI-X Multiple Vector Interrupt Handler for outbound completions. */
+static irqreturn_t qlge_msix_tx_isr(int irq, void *dev_id)
+{
+	struct rx_ring *rx_ring = dev_id;
+#ifndef QLGE_FAST_TXQ
+	queue_delayed_work_on(rx_ring->cpu, rx_ring->qdev->q_workqueue,
+			      &rx_ring->rx_work, 0);
+#else
+	ql_clean_outbound_rx_ring(rx_ring);
+	ql_enable_completion_interrupt(rx_ring->qdev, rx_ring->irq);
+#endif
+	return IRQ_HANDLED;
+}
+
+/* MSI-X Multiple Vector Interrupt Handler for inbound completions. */
+static irqreturn_t qlge_msix_rx_isr(int irq, void *dev_id)
+{
+	struct rx_ring *rx_ring = dev_id;
+	struct ql_adapter *qdev = rx_ring->qdev;
+	netif_rx_schedule(qdev->ndev, &rx_ring->napi);
+	return IRQ_HANDLED;
+}
+
+/* We check here to see if we're already handling a legacy
+ * interrupt.  If we are, then it must belong to another
+ * chip with which we're sharing the interrupt line.
+ */
+int ql_legacy_check(struct ql_adapter *qdev)
+{
+	int err;
+	spin_lock(&qdev->legacy_lock);
+	err = atomic_read(&qdev->intr_context[0].irq_cnt);
+	spin_unlock(&qdev->legacy_lock);
+	return err;
+}
+
+/* This handles a fatal error, MPI activity, and the default
+ * rx_ring in an MSI-X multiple vector environment.
+ * In MSI/Legacy environment it also process the rest of
+ * the rx_rings.
+ */
+static irqreturn_t qlge_isr(int irq, void *dev_id)
+{
+	struct rx_ring *rx_ring = dev_id;
+	struct ql_adapter *qdev = rx_ring->qdev;
+	struct intr_context *intr_context = &qdev->intr_context[0];
+	u32 var;
+	int i;
+	int work_done = 0;
+
+	if (qdev->legacy_check && qdev->legacy_check(qdev)) {
+		printk(KERN_ERR "%s: Already busy, not our interrupt.\n",
+		       __func__);
+		QPRINTK(qdev, INTR, INFO, "Already busy, not our interrupt.\n");
+		return IRQ_NONE;	/* Not our interrupt */
+	}
+
+	var = ql_read32(qdev, STS);
+
+#ifdef PALLADIUM
+/* Palladium workaround start: */
+	while (var == -1) {
+		QPRINTK(qdev, INTR, DEBUG, "got STS == -1, reading again.\n");
+		var = ql_read32(qdev, STS);
+	}
+/* Palladium workaround end: */
+#endif
+
+	/*
+	 * Check for fatal error.
+	 */
+	if (var & STS_FE) {
+		ql_queue_asic_error(qdev);
+		QPRINTK(qdev, INTR, ERR, "Got fatal error, STS = %x.\n", var);
+		var = ql_read32(qdev, ERR_STS);
+		QPRINTK(qdev, INTR, ERR,
+			"Resetting chip. Error Status Register = 0x%x\n", var);
+		return IRQ_HANDLED;
+	}
+
+	/*
+	 * Check MPI processor activity.
+	 */
+	if (var & STS_PI) {
+		/*
+		 * We've got an async event or mailbox completion.
+		 * Handle it and clear the source of the interrupt.
+		 */
+		QPRINTK(qdev, INTR, ERR, "Got MPI processor interrupt.\n");
+		ql_disable_completion_interrupt(qdev, intr_context->intr);
+		queue_delayed_work_on(smp_processor_id(), qdev->workqueue,
+				      &qdev->mpi_work, 0);
+		work_done++;
+	}
+
+	/*
+	 * Check the default queue and wake handler if active.
+	 */
+	rx_ring = &qdev->rx_ring[0];
+	if (ql_read_sh_reg(rx_ring->prod_idx_sh_reg) != rx_ring->cnsmr_idx) {
+		QPRINTK(qdev, INTR, INFO, "Waking handler for rx_ring[0].\n");
+		ql_disable_completion_interrupt(qdev, intr_context->intr);
+		queue_delayed_work_on(smp_processor_id(), qdev->q_workqueue,
+				      &rx_ring->rx_work, 0);
+		work_done++;
+	}
+
+	if (!test_bit(QL_MSIX_ENABLED, &qdev->flags)) {
+		/*
+		 * Start the DPC for each active queue.
+		 */
+		for (i = 1; i < qdev->rx_ring_count; i++) {
+			rx_ring = &qdev->rx_ring[i];
+			if (ql_read_sh_reg(rx_ring->prod_idx_sh_reg) !=
+			    rx_ring->cnsmr_idx) {
+				QPRINTK(qdev, INTR, INFO,
+					"Waking handler for rx_ring[%d].\n", i);
+				ql_disable_completion_interrupt(qdev,
+								intr_context->
+								intr);
+				if (i < qdev->rss_ring_first_cq_id)
+					queue_delayed_work_on(rx_ring->cpu,
+							      qdev->q_workqueue,
+							      &rx_ring->rx_work,
+							      0);
+				else
+					netif_rx_schedule(qdev->ndev,
+							  &rx_ring->napi);
+				work_done++;
+			}
+		}
+	}
+	return work_done ? IRQ_HANDLED : IRQ_NONE;
+}
+
+static int ql_tso(struct sk_buff *skb, struct ob_mac_tso_iocb_req *mac_iocb_ptr)
+{
+
+	if (skb_is_gso(skb)) {
+		int err;
+		if (skb_header_cloned(skb)) {
+			err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
+			if (err)
+				return err;
+		}
+
+		mac_iocb_ptr->opcode = OPCODE_OB_MAC_TSO_IOCB;
+		mac_iocb_ptr->flags3 |= OB_MAC_TSO_IOCB_IC;
+		mac_iocb_ptr->frame_len = cpu_to_le32((u32) skb->len);
+		mac_iocb_ptr->total_hdrs_len =
+		    cpu_to_le16(skb_transport_offset(skb) + tcp_hdrlen(skb));
+		mac_iocb_ptr->net_trans_offset =
+		    cpu_to_le16(skb_network_offset(skb) |
+				skb_transport_offset(skb)
+				<< OB_MAC_TRANSPORT_HDR_SHIFT);
+		mac_iocb_ptr->mss = cpu_to_le16(skb_shinfo(skb)->gso_size);
+		mac_iocb_ptr->flags2 |= OB_MAC_TSO_IOCB_LSO;
+		if (likely(skb->protocol == htons(ETH_P_IP))) {
+			struct iphdr *iph = ip_hdr(skb);
+			iph->check = 0;
+			mac_iocb_ptr->flags1 |= OB_MAC_TSO_IOCB_IP4;
+			tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr,
+								 iph->daddr, 0,
+								 IPPROTO_TCP,
+								 0);
+		} else if (skb->protocol == htons(ETH_P_IPV6)) {
+			mac_iocb_ptr->flags1 |= OB_MAC_TSO_IOCB_IP6;
+			tcp_hdr(skb)->check =
+			    ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
+					     &ipv6_hdr(skb)->daddr,
+					     0, IPPROTO_TCP, 0);
+		}
+		return 1;
+	}
+	return 0;
+}
+
+static void ql_hw_csum_setup(struct sk_buff *skb,
+			     struct ob_mac_tso_iocb_req *mac_iocb_ptr)
+{
+	int len;
+	struct iphdr *iph = ip_hdr(skb);
+	u16 *check;
+	mac_iocb_ptr->opcode = OPCODE_OB_MAC_TSO_IOCB;
+	mac_iocb_ptr->frame_len = cpu_to_le32((u32) skb->len);
+	mac_iocb_ptr->net_trans_offset =
+		cpu_to_le16(skb_network_offset(skb) |
+		skb_transport_offset(skb) << OB_MAC_TRANSPORT_HDR_SHIFT);
+
+	mac_iocb_ptr->flags1 |= OB_MAC_TSO_IOCB_IP4;
+	len = (ntohs(iph->tot_len) - (iph->ihl << 2));
+	if (likely(iph->protocol == IPPROTO_TCP)) {
+		check = &(tcp_hdr(skb)->check);
+		mac_iocb_ptr->flags2 |= OB_MAC_TSO_IOCB_TC;
+		mac_iocb_ptr->total_hdrs_len =
+		    cpu_to_le16(skb_transport_offset(skb) +
+				(tcp_hdr(skb)->doff << 2));
+	} else {
+		check = &(udp_hdr(skb)->check);
+		mac_iocb_ptr->flags2 |= OB_MAC_TSO_IOCB_UC;
+		mac_iocb_ptr->total_hdrs_len =
+		    cpu_to_le16(skb_transport_offset(skb) +
+				sizeof(struct udphdr));
+	}
+	*check = ~csum_tcpudp_magic(iph->saddr,
+				    iph->daddr, len, iph->protocol, 0);
+}
+
+static int qlge_send(struct sk_buff *skb, struct net_device *ndev)
+{
+	struct tx_ring_desc *tx_ring_desc;
+	struct ob_mac_iocb_req *mac_iocb_ptr;
+	struct ql_adapter *qdev = netdev_priv(ndev);
+	int tso;
+	struct tx_ring *tx_ring;
+	u32 tx_ring_idx = (u32) QL_TXQ_IDX(qdev, skb);
+
+	tx_ring = &qdev->tx_ring[tx_ring_idx];
+
+	if (unlikely(atomic_read(&tx_ring->tx_count) < 2)) {
+		QPRINTK(qdev, TX_QUEUED, INFO,
+			"%s: shutting down tx queue %d du to lack of resources.\n",
+			__func__, tx_ring_idx);
+		netif_stop_queue(ndev);
+		atomic_inc(&tx_ring->queue_stopped);
+		return NETDEV_TX_BUSY;
+	}
+	tx_ring_desc = &tx_ring->q[tx_ring->prod_idx];
+	mac_iocb_ptr = tx_ring_desc->queue_entry;
+	memset((void *)mac_iocb_ptr, 0, sizeof(mac_iocb_ptr));
+	if (ql_map_send(qdev, mac_iocb_ptr, skb, tx_ring_desc) != NETDEV_TX_OK) {
+		QPRINTK(qdev, TX_QUEUED, ERR, "Could not map the segments.\n");
+		return NETDEV_TX_BUSY;
+	}
+
+	mac_iocb_ptr->opcode = OPCODE_OB_MAC_IOCB;
+	mac_iocb_ptr->tid = tx_ring_desc->index;
+	/* We use the upper 32-bits to store the tx queue for this IO.
+	 * When we get the completion we can use it to establish the context.
+	 */
+	mac_iocb_ptr->txq_idx = tx_ring_idx;
+	tx_ring_desc->skb = skb;
+
+	mac_iocb_ptr->frame_len = cpu_to_le16((u16) skb->len);
+
+	if (qdev->vlgrp && vlan_tx_tag_present(skb)) {
+		QPRINTK(qdev, TX_QUEUED, DEBUG, "Adding a vlan tag %d.\n",
+			vlan_tx_tag_get(skb));
+		mac_iocb_ptr->flags3 |= OB_MAC_IOCB_V;
+		mac_iocb_ptr->vlan_tci = cpu_to_le16(vlan_tx_tag_get(skb));
+	}
+	tso = ql_tso(skb, (struct ob_mac_tso_iocb_req *)mac_iocb_ptr);
+	if (tso < 0) {
+		dev_kfree_skb_any(skb);
+		return NETDEV_TX_OK;
+	} else if (unlikely(!tso) && (skb->ip_summed == CHECKSUM_PARTIAL)) {
+		ql_hw_csum_setup(skb,
+				 (struct ob_mac_tso_iocb_req *)mac_iocb_ptr);
+	}
+	QL_DUMP_OB_MAC_IOCB(mac_iocb_ptr);
+	tx_ring->prod_idx++;
+	if (tx_ring->prod_idx == tx_ring->wq_len)
+		tx_ring->prod_idx = 0;
+	wmb();
+
+	ql_write_db_reg(tx_ring->prod_idx, tx_ring->prod_idx_db_reg);
+	ndev->trans_start = jiffies;
+	QPRINTK(qdev, TX_QUEUED, DEBUG, "tx queued, slot %d, len %d\n",
+		tx_ring->prod_idx, skb->len);
+
+	atomic_dec(&tx_ring->tx_count);
+	return NETDEV_TX_OK;
+}
+
+static void ql_free_shadow_space(struct ql_adapter *qdev)
+{
+	if (qdev->rx_ring_shadow_reg_area) {
+		pci_free_consistent(qdev->pdev,
+				    PAGE_SIZE,
+				    qdev->rx_ring_shadow_reg_area,
+				    qdev->rx_ring_shadow_reg_dma);
+		qdev->rx_ring_shadow_reg_area = NULL;
+	}
+	if (qdev->tx_ring_shadow_reg_area) {
+		pci_free_consistent(qdev->pdev,
+				    PAGE_SIZE,
+				    qdev->tx_ring_shadow_reg_area,
+				    qdev->tx_ring_shadow_reg_dma);
+		qdev->tx_ring_shadow_reg_area = NULL;
+	}
+}
+
+static int ql_alloc_shadow_space(struct ql_adapter *qdev)
+{
+	qdev->rx_ring_shadow_reg_area =
+	    pci_alloc_consistent(qdev->pdev,
+				 PAGE_SIZE, &qdev->rx_ring_shadow_reg_dma);
+	if (qdev->rx_ring_shadow_reg_area == NULL) {
+		QPRINTK(qdev, IFUP, ERR,
+			"Allocation of RX shadow space failed.\n");
+		return -ENOMEM;
+	}
+	qdev->tx_ring_shadow_reg_area =
+	    pci_alloc_consistent(qdev->pdev, PAGE_SIZE,
+				 &qdev->tx_ring_shadow_reg_dma);
+	if (qdev->tx_ring_shadow_reg_area == NULL) {
+		QPRINTK(qdev, IFUP, ERR,
+			"Allocation of TX shadow space failed.\n");
+		goto err_wqp_sh_area;
+	}
+	return 0;
+
+err_wqp_sh_area:
+	pci_free_consistent(qdev->pdev,
+			    PAGE_SIZE,
+			    qdev->rx_ring_shadow_reg_area,
+			    qdev->rx_ring_shadow_reg_dma);
+	return -ENOMEM;
+}
+
+static void ql_init_tx_ring(struct ql_adapter *qdev, struct tx_ring *tx_ring)
+{
+	struct tx_ring_desc *tx_ring_desc;
+	int i;
+	struct ob_mac_iocb_req *mac_iocb_ptr;
+
+	mac_iocb_ptr = tx_ring->wq_base;
+	tx_ring_desc = tx_ring->q;
+	for (i = 0; i < tx_ring->wq_len; i++) {
+		tx_ring_desc->index = i;
+		tx_ring_desc->skb = NULL;
+		tx_ring_desc->queue_entry = mac_iocb_ptr;
+		mac_iocb_ptr++;
+		tx_ring_desc++;
+	}
+	atomic_set(&tx_ring->tx_count, tx_ring->wq_len);
+	atomic_set(&tx_ring->queue_stopped, 0);
+}
+
+static void ql_free_tx_resources(struct ql_adapter *qdev,
+				 struct tx_ring *tx_ring)
+{
+	if (tx_ring->wq_base) {
+		pci_free_consistent(qdev->pdev, tx_ring->wq_size,
+				    tx_ring->wq_base, tx_ring->wq_base_dma);
+		tx_ring->wq_base = NULL;
+	}
+	kfree(tx_ring->q);
+	tx_ring->q = NULL;
+}
+
+static int ql_alloc_tx_resources(struct ql_adapter *qdev,
+				 struct tx_ring *tx_ring)
+{
+	tx_ring->wq_base =
+	    pci_alloc_consistent(qdev->pdev, tx_ring->wq_size,
+				 &tx_ring->wq_base_dma);
+
+	if ((tx_ring->wq_base == NULL)
+	    || tx_ring->wq_base_dma & (tx_ring->wq_size - 1)) {
+		QPRINTK(qdev, IFUP, ERR, "tx_ring alloc failed.\n");
+		return -ENOMEM;
+	}
+	tx_ring->q =
+	    kmalloc(tx_ring->wq_len * sizeof(struct tx_ring_desc), GFP_KERNEL);
+	if (tx_ring->q == NULL)
+		goto err;
+
+	return 0;
+err:
+	pci_free_consistent(qdev->pdev, tx_ring->wq_size,
+			    tx_ring->wq_base, tx_ring->wq_base_dma);
+	return -ENOMEM;
+}
+
+void ql_free_lbq_buffers(struct ql_adapter *qdev, struct rx_ring *rx_ring)
+{
+	int i;
+	struct bq_desc *lbq_desc;
+
+	for (i = 0; i < rx_ring->lbq_len; i++) {
+		lbq_desc = &rx_ring->lbq[i];
+		if (lbq_desc->p.lbq_page) {
+			pci_unmap_page(qdev->pdev,
+				       pci_unmap_addr(lbq_desc, mapaddr),
+				       pci_unmap_len(lbq_desc, maplen),
+				       PCI_DMA_FROMDEVICE);
+
+			put_page(lbq_desc->p.lbq_page);
+			lbq_desc->p.lbq_page = NULL;
+		}
+		lbq_desc->bq->addr_lo = 0;
+		lbq_desc->bq->addr_hi = 0;
+	}
+}
+
+/*
+ * Allocate and map a page for each element of the lbq.
+ */
+static int ql_alloc_lbq_buffers(struct ql_adapter *qdev,
+				struct rx_ring *rx_ring)
+{
+	int i;
+	struct bq_desc *lbq_desc;
+	u64 map;
+	struct bq_element *bq = rx_ring->lbq_base;
+
+	for (i = 0; i < rx_ring->lbq_len; i++) {
+		lbq_desc = &rx_ring->lbq[i];
+		memset(lbq_desc, 0, sizeof(lbq_desc));
+		lbq_desc->bq = bq;
+		lbq_desc->index = i;
+		lbq_desc->p.lbq_page = alloc_page(GFP_ATOMIC);
+		if (unlikely(!lbq_desc->p.lbq_page)) {
+			QPRINTK(qdev, IFUP, ERR, "failed alloc_page().\n");
+			goto mem_error;
+		} else {
+			map = pci_map_page(qdev->pdev,
+					   lbq_desc->p.lbq_page,
+					   0, PAGE_SIZE, PCI_DMA_FROMDEVICE);
+			if (pci_dma_mapping_error(map)) {
+				QPRINTK(qdev, IFUP, ERR,
+					"PCI mapping failed.\n");
+				goto mem_error;
+			}
+			pci_unmap_addr_set(lbq_desc, mapaddr, map);
+			pci_unmap_len_set(lbq_desc, maplen, PAGE_SIZE);
+			bq->addr_lo = cpu_to_le32(map);
+			bq->addr_hi = cpu_to_le32(map >> 32);
+		}
+		bq++;
+	}
+	return 0;
+mem_error:
+	ql_free_lbq_buffers(qdev, rx_ring);
+	return -ENOMEM;
+}
+
+void ql_free_sbq_buffers(struct ql_adapter *qdev, struct rx_ring *rx_ring)
+{
+	int i;
+	struct bq_desc *sbq_desc;
+
+	for (i = 0; i < rx_ring->sbq_len; i++) {
+		sbq_desc = &rx_ring->sbq[i];
+		if (sbq_desc == NULL) {
+			QPRINTK(qdev, IFUP, ERR, "sbq_desc %d is NULL.\n", i);
+			return;
+		}
+		if (sbq_desc->p.skb) {
+			pci_unmap_single(qdev->pdev,
+					 pci_unmap_addr(sbq_desc, mapaddr),
+					 pci_unmap_len(sbq_desc, maplen),
+					 PCI_DMA_FROMDEVICE);
+			dev_kfree_skb(sbq_desc->p.skb);
+			sbq_desc->p.skb = NULL;
+		}
+		if (sbq_desc->bq == NULL) {
+			QPRINTK(qdev, IFUP, ERR, "sbq_desc->bq %d is NULL.\n",
+				i);
+			return;
+		}
+		sbq_desc->bq->addr_lo = 0;
+		sbq_desc->bq->addr_hi = 0;
+	}
+}
+
+/* Allocate and map an skb for each element of the sbq. */
+static int ql_alloc_sbq_buffers(struct ql_adapter *qdev,
+				struct rx_ring *rx_ring)
+{
+	int i;
+	struct bq_desc *sbq_desc;
+	struct sk_buff *skb;
+	u64 map;
+	struct bq_element *bq = rx_ring->sbq_base;
+
+	for (i = 0; i < rx_ring->sbq_len; i++) {
+		sbq_desc = &rx_ring->sbq[i];
+		memset(sbq_desc, 0, sizeof(sbq_desc));
+		sbq_desc->index = i;
+		sbq_desc->bq = bq;
+		skb = netdev_alloc_skb(qdev->ndev, rx_ring->sbq_buf_size);
+		if (unlikely(!skb)) {
+			/* Better luck next round */
+			QPRINTK(qdev, IFUP, ERR,
+				"small buff alloc failed for %d bytes at index %d.\n",
+				rx_ring->sbq_buf_size, i);
+			goto mem_err;
+		}
+		skb_reserve(skb, QLGE_SB_PAD);
+		sbq_desc->p.skb = skb;
+		/*
+		 * Map only half the buffer. Because the
+		 * other half may get some data copied to it
+		 * when the completion arrives.
+		 */
+		map = pci_map_single(qdev->pdev,
+				     skb->data,
+				     rx_ring->sbq_buf_size / 2,
+				     PCI_DMA_FROMDEVICE);
+		if (pci_dma_mapping_error(map)) {
+			QPRINTK(qdev, IFUP, ERR, "PCI mapping failed.\n");
+			goto mem_err;
+		}
+		pci_unmap_addr_set(sbq_desc, mapaddr, map);
+		pci_unmap_len_set(sbq_desc, maplen, rx_ring->sbq_buf_size / 2);
+		bq->addr_lo =	/*sbq_desc->addr_lo = */
+		    cpu_to_le32(map);
+		bq->addr_hi =	/*sbq_desc->addr_hi = */
+		    cpu_to_le32(map >> 32);
+		bq++;
+	}
+	return 0;
+mem_err:
+	ql_free_sbq_buffers(qdev, rx_ring);
+	return -ENOMEM;
+}
+
+static void ql_free_rx_resources(struct ql_adapter *qdev,
+				 struct rx_ring *rx_ring)
+{
+	if (rx_ring->sbq_len)
+		ql_free_sbq_buffers(qdev, rx_ring);
+	if (rx_ring->lbq_len)
+		ql_free_lbq_buffers(qdev, rx_ring);
+
+	/* Free the small buffer queue. */
+	if (rx_ring->sbq_base) {
+		pci_free_consistent(qdev->pdev,
+				    rx_ring->sbq_size,
+				    rx_ring->sbq_base, rx_ring->sbq_base_dma);
+		rx_ring->sbq_base = NULL;
+	}
+
+	/* Free the small buffer queue control blocks. */
+	kfree(rx_ring->sbq);
+	rx_ring->sbq = NULL;
+
+	/* Free the large buffer queue. */
+	if (rx_ring->lbq_base) {
+		pci_free_consistent(qdev->pdev,
+				    rx_ring->lbq_size,
+				    rx_ring->lbq_base, rx_ring->lbq_base_dma);
+		rx_ring->lbq_base = NULL;
+	}
+
+	/* Free the large buffer queue control blocks. */
+	kfree(rx_ring->lbq);
+	rx_ring->lbq = NULL;
+
+	/* Free the rx queue. */
+	if (rx_ring->cq_base) {
+		pci_free_consistent(qdev->pdev,
+				    rx_ring->cq_size,
+				    rx_ring->cq_base, rx_ring->cq_base_dma);
+		rx_ring->cq_base = NULL;
+	}
+}
+
+/* Allocate queues and buffers for this completions queue based
+ * on the values in the parameter structure. */
+static int ql_alloc_rx_resources(struct ql_adapter *qdev,
+				 struct rx_ring *rx_ring)
+{
+
+	/*
+	 * Allocate the completion queue for this rx_ring.
+	 */
+	rx_ring->cq_base =
+	    pci_alloc_consistent(qdev->pdev, rx_ring->cq_size,
+				 &rx_ring->cq_base_dma);
+
+	if (rx_ring->cq_base == NULL) {
+		QPRINTK(qdev, IFUP, ERR, "rx_ring alloc failed.\n");
+		return -ENOMEM;
+	}
+
+	if (rx_ring->sbq_len) {
+		/*
+		 * Allocate small buffer queue.
+		 */
+		rx_ring->sbq_base =
+		    pci_alloc_consistent(qdev->pdev, rx_ring->sbq_size,
+					 &rx_ring->sbq_base_dma);
+
+		if (rx_ring->sbq_base == NULL) {
+			QPRINTK(qdev, IFUP, ERR,
+				"Small buffer queue allocation failed.\n");
+			goto err_mem;
+		}
+
+		/*
+		 * Allocate small buffer queue control blocks.
+		 */
+		rx_ring->sbq =
+		    kmalloc(rx_ring->sbq_len * sizeof(struct bq_desc),
+			    GFP_KERNEL);
+		if (rx_ring->sbq == NULL) {
+			QPRINTK(qdev, IFUP, ERR,
+				"Small buffer queue control block allocation failed.\n");
+			goto err_mem;
+		}
+
+		if (ql_alloc_sbq_buffers(qdev, rx_ring)) {
+			QPRINTK(qdev, IFUP, ERR,
+				"Small buffer allocation failed.\n");
+			goto err_mem;
+		}
+	}
+
+	if (rx_ring->lbq_len) {
+		/*
+		 * Allocate large buffer queue.
+		 */
+		rx_ring->lbq_base =
+		    pci_alloc_consistent(qdev->pdev, rx_ring->lbq_size,
+					 &rx_ring->lbq_base_dma);
+
+		if (rx_ring->lbq_base == NULL) {
+			QPRINTK(qdev, IFUP, ERR,
+				"Large buffer queue allocation failed.\n");
+			goto err_mem;
+		}
+		/*
+		 * Allocate large buffer queue control blocks.
+		 */
+		rx_ring->lbq =
+		    kmalloc(rx_ring->lbq_len * sizeof(struct bq_desc),
+			    GFP_KERNEL);
+		if (rx_ring->lbq == NULL) {
+			QPRINTK(qdev, IFUP, ERR,
+				"Large buffer queue control block allocation failed.\n");
+			goto err_mem;
+		}
+
+		/*
+		 * Allocate the buffers.
+		 */
+		if (ql_alloc_lbq_buffers(qdev, rx_ring)) {
+			QPRINTK(qdev, IFUP, ERR,
+				"Large buffer allocation failed.\n");
+			goto err_mem;
+		}
+	}
+
+	return 0;
+
+err_mem:
+	ql_free_rx_resources(qdev, rx_ring);
+	return -ENOMEM;
+}
+
+static void ql_tx_ring_clean(struct ql_adapter *qdev)
+{
+	struct tx_ring *tx_ring;
+	struct tx_ring_desc *tx_ring_desc;
+	int i, j;
+
+	/*
+	 * Loop through all queues and free
+	 * any resources.
+	 */
+	for (j = 0; j < qdev->tx_ring_count; j++) {
+		tx_ring = &qdev->tx_ring[j];
+		for (i = 0; i < tx_ring->wq_len; i++) {
+			tx_ring_desc = &tx_ring->q[i];
+			if (tx_ring_desc && tx_ring_desc->skb) {
+				QPRINTK(qdev, IFDOWN, ERR,
+				"Freeing lost SKB %p, from queue %d, index %d.\n",
+					tx_ring_desc->skb, j,
+					tx_ring_desc->index);
+				ql_unmap_send(qdev, tx_ring_desc,
+					      tx_ring_desc->map_cnt);
+				dev_kfree_skb(tx_ring_desc->skb);
+				tx_ring_desc->skb = NULL;
+			}
+		}
+	}
+}
+
+static void ql_free_ring_cb(struct ql_adapter *qdev)
+{
+	kfree(qdev->ring_mem);
+}
+
+static int ql_alloc_ring_cb(struct ql_adapter *qdev)
+{
+	/* Allocate space for tx/rx ring control blocks. */
+	qdev->ring_mem_size =
+	    (qdev->tx_ring_count * sizeof(struct tx_ring)) +
+	    (qdev->rx_ring_count * sizeof(struct rx_ring));
+	qdev->ring_mem = kmalloc(qdev->ring_mem_size, GFP_KERNEL);
+	if (qdev->ring_mem == NULL) {
+		return -ENOMEM;
+	} else {
+		qdev->rx_ring = qdev->ring_mem;
+		qdev->tx_ring = qdev->ring_mem +
+		    (qdev->rx_ring_count * sizeof(struct rx_ring));
+	}
+	return 0;
+}
+
+static void ql_free_mem_resources(struct ql_adapter *qdev)
+{
+	int i;
+
+	for (i = 0; i < qdev->tx_ring_count; i++)
+		ql_free_tx_resources(qdev, &qdev->tx_ring[i]);
+	for (i = 0; i < qdev->rx_ring_count; i++)
+		ql_free_rx_resources(qdev, &qdev->rx_ring[i]);
+	ql_free_shadow_space(qdev);
+}
+
+static int ql_alloc_mem_resources(struct ql_adapter *qdev)
+{
+	int i;
+
+	/* Allocate space for our shadow registers and such. */
+	if (ql_alloc_shadow_space(qdev))
+		return -ENOMEM;
+
+	for (i = 0; i < qdev->rx_ring_count; i++) {
+		if (ql_alloc_rx_resources(qdev, &qdev->rx_ring[i]) != 0) {
+			QPRINTK(qdev, IFUP, ERR,
+				"RX resource allocation failed.\n");
+			goto err_mem;
+		}
+	}
+	/* Allocate tx queue resources */
+	for (i = 0; i < qdev->tx_ring_count; i++) {
+		if (ql_alloc_tx_resources(qdev, &qdev->tx_ring[i]) != 0) {
+			QPRINTK(qdev, IFUP, ERR,
+				"TX resource allocation failed.\n");
+			goto err_mem;
+		}
+	}
+	return 0;
+
+err_mem:
+	ql_free_mem_resources(qdev);
+	return -ENOMEM;
+}
+
+/* Set up the rx ring control block and pass it to the chip.
+ * The control block is defined as
+ * "Completion Queue Initialization Control Block", or cqicb.
+ */
+static int ql_start_rx_ring(struct ql_adapter *qdev, struct rx_ring *rx_ring)
+{
+	struct cqicb *cqicb = &rx_ring->cqicb;
+	void *shadow_reg = qdev->rx_ring_shadow_reg_area +
+	    (rx_ring->cq_id * sizeof(u64) * 4);
+	u64 shadow_reg_dma = qdev->rx_ring_shadow_reg_dma +
+	    (rx_ring->cq_id * sizeof(u64) * 4);
+	void __iomem *doorbell_area =
+	    qdev->doorbell_area + (DB_PAGE_SIZE * (128 + rx_ring->cq_id));
+	int err = 0;
+	u16 bq_len;
+
+	/* Set up the shadow registers for this ring. */
+	rx_ring->prod_idx_sh_reg = shadow_reg;
+	rx_ring->prod_idx_sh_reg_dma = shadow_reg_dma;
+	shadow_reg += sizeof(u64);
+	shadow_reg_dma += sizeof(u64);
+	rx_ring->lbq_base_indirect = shadow_reg;
+	rx_ring->lbq_base_indirect_dma = shadow_reg_dma;
+	shadow_reg += sizeof(u64);
+	shadow_reg_dma += sizeof(u64);
+	rx_ring->sbq_base_indirect = shadow_reg;
+	rx_ring->sbq_base_indirect_dma = shadow_reg_dma;
+
+	/* PCI doorbell mem area + 0x00 for consumer index register */
+	rx_ring->cnsmr_idx_db_reg = (u32 *) doorbell_area;
+	rx_ring->cnsmr_idx = 0;
+	rx_ring->curr_entry = rx_ring->cq_base;
+
+	/* PCI doorbell mem area + 0x04 for valid register */
+	rx_ring->valid_db_reg = doorbell_area + 0x04;
+
+	/* PCI doorbell mem area + 0x18 for large buffer consumer */
+	rx_ring->lbq_prod_idx_db_reg = (u32 *) (doorbell_area + 0x18);
+
+	/* PCI doorbell mem area + 0x1c */
+	rx_ring->sbq_prod_idx_db_reg = (u32 *) (doorbell_area + 0x1c);
+
+	memset((void *)cqicb, 0, sizeof(struct cqicb));
+	cqicb->msix_vect = rx_ring->irq;
+
+	cqicb->len = cpu_to_le16(rx_ring->cq_len | LEN_V | LEN_CPP_CONT);
+
+	cqicb->addr_lo = cpu_to_le32(rx_ring->cq_base_dma);
+	cqicb->addr_hi = cpu_to_le32((u64) rx_ring->cq_base_dma >> 32);
+
+	cqicb->prod_idx_addr_lo = cpu_to_le32(rx_ring->prod_idx_sh_reg_dma);
+	cqicb->prod_idx_addr_hi =
+	    cpu_to_le32((u64) rx_ring->prod_idx_sh_reg_dma >> 32);
+
+	/*
+	 * Set up the control block load flags.
+	 */
+	cqicb->flags = FLAGS_LC |	/* Load queue base address */
+	    FLAGS_LV |		/* Load MSI-X vector */
+	    FLAGS_LI;		/* Load irq delay values */
+	if (rx_ring->lbq_len) {
+		cqicb->flags |= FLAGS_LL;	/* Load lbq values */
+		*((u64 *) rx_ring->lbq_base_indirect) = rx_ring->lbq_base_dma;
+		cqicb->lbq_addr_lo =
+		    cpu_to_le32(rx_ring->lbq_base_indirect_dma);
+		cqicb->lbq_addr_hi =
+		    cpu_to_le32((u64) rx_ring->lbq_base_indirect_dma >> 32);
+		cqicb->lbq_buf_size = cpu_to_le32(rx_ring->lbq_buf_size);
+		bq_len = (u16) rx_ring->lbq_len;
+		cqicb->lbq_len = cpu_to_le16(bq_len);
+		rx_ring->lbq_prod_idx = rx_ring->lbq_len - 16;
+		rx_ring->lbq_curr_idx = 0;
+		rx_ring->lbq_clean_idx = rx_ring->lbq_prod_idx;
+		rx_ring->lbq_free_cnt = 16;
+	}
+	if (rx_ring->sbq_len) {
+		cqicb->flags |= FLAGS_LS;	/* Load sbq values */
+		*((u64 *) rx_ring->sbq_base_indirect) = rx_ring->sbq_base_dma;
+		cqicb->sbq_addr_lo =
+		    cpu_to_le32(rx_ring->sbq_base_indirect_dma);
+		cqicb->sbq_addr_hi =
+		    cpu_to_le32((u64) rx_ring->sbq_base_indirect_dma >> 32);
+		cqicb->sbq_buf_size =
+		    cpu_to_le16(((rx_ring->sbq_buf_size / 2) + 8) & 0xfffffff8);
+		bq_len = (u16) rx_ring->sbq_len;
+		cqicb->sbq_len = cpu_to_le16(bq_len);
+		rx_ring->sbq_prod_idx = rx_ring->sbq_len - 16;
+		rx_ring->sbq_curr_idx = 0;
+		rx_ring->sbq_clean_idx = rx_ring->sbq_prod_idx;
+		rx_ring->sbq_free_cnt = 16;
+	}
+	switch (rx_ring->type) {
+	case TX_Q:
+		/* If there's only one interrupt, then we use
+		 * worker threads to process the outbound
+		 * completion handling rx_rings. We do this so
+		 * they can be run on multiple CPUs. There is
+		 * room to play with this more where we would only
+		 * run in a worker if there are more than x number
+		 * of outbound completions on the queue and more
+		 * than one queue active.  Some threshold that
+		 * would indicate a benefit in spite of the cost
+		 * of a context switch.
+		 * If there's more than one interrupt, then the
+		 * outbound completions are processed in the ISR.
+		 */
+		if (!test_bit(QL_MSIX_ENABLED, &qdev->flags))
+			INIT_DELAYED_WORK(&rx_ring->rx_work, ql_tx_clean);
+		else {
+#ifndef QLGE_FAST_TXQ
+			/* With all debug warnings on we see a WARN_ON message
+			 * when we free the skb in the interrupt context.
+			 */
+			INIT_DELAYED_WORK(&rx_ring->rx_work, ql_tx_clean);
+#endif
+		}
+		cqicb->irq_delay = cpu_to_le16(qdev->tx_coalesce_usecs);
+		cqicb->pkt_delay = cpu_to_le16(qdev->tx_max_coalesced_frames);
+		break;
+	case DEFAULT_Q:
+		INIT_DELAYED_WORK(&rx_ring->rx_work, ql_rx_clean);
+		cqicb->irq_delay = 0;
+		cqicb->pkt_delay = 0;
+		break;
+	case RX_Q:
+		/* Inbound completion handling rx_rings run in
+		 * separate NAPI contexts.
+		 */
+		netif_napi_add(qdev->ndev, &rx_ring->napi, ql_napi_poll_msix,
+			       64);
+		cqicb->irq_delay = cpu_to_le16(qdev->rx_coalesce_usecs);
+		cqicb->pkt_delay = cpu_to_le16(qdev->rx_max_coalesced_frames);
+		break;
+	default:
+		QPRINTK(qdev, IFUP, DEBUG, "Invalid rx_ring->type = %d.\n",
+			rx_ring->type);
+	}
+	QPRINTK(qdev, IFUP, INFO, "Initializing rx work queue.\n");
+	err = ql_write_cfg(qdev, cqicb, sizeof(struct cqicb),
+			   CFG_LCQ, rx_ring->cq_id);
+	if (err) {
+		QPRINTK(qdev, IFUP, ERR, "Failed to load CQICB.\n");
+		return err;
+	}
+	QPRINTK(qdev, IFUP, INFO, "Successfully loaded CQICB.\n");
+	/*
+	 * Advance the producer index for the buffer queues.
+	 */
+	wmb();
+	if (rx_ring->lbq_len)
+		ql_write_db_reg(rx_ring->lbq_prod_idx,
+				rx_ring->lbq_prod_idx_db_reg);
+	if (rx_ring->sbq_len)
+		ql_write_db_reg(rx_ring->sbq_prod_idx,
+				rx_ring->sbq_prod_idx_db_reg);
+	return err;
+}
+
+static int ql_start_tx_ring(struct ql_adapter *qdev, struct tx_ring *tx_ring)
+{
+	struct wqicb *wqicb = (struct wqicb *)tx_ring;
+	void __iomem *doorbell_area =
+	    qdev->doorbell_area + (DB_PAGE_SIZE * tx_ring->wq_id);
+	void *shadow_reg = qdev->tx_ring_shadow_reg_area +
+	    (tx_ring->wq_id * sizeof(u64));
+	u64 shadow_reg_dma = qdev->tx_ring_shadow_reg_dma +
+	    (tx_ring->wq_id * sizeof(u64));
+	int err = 0;
+
+	/*
+	 * Assign doorbell registers for this tx_ring.
+	 */
+	/* TX PCI doorbell mem area for tx producer index */
+	tx_ring->prod_idx_db_reg = (u32 *) doorbell_area;
+	tx_ring->prod_idx = 0;
+	/* TX PCI doorbell mem area + 0x04 */
+	tx_ring->valid_db_reg = doorbell_area + 0x04;
+
+	/*
+	 * Assign shadow registers for this tx_ring.
+	 */
+	tx_ring->cnsmr_idx_sh_reg = shadow_reg;
+	tx_ring->cnsmr_idx_sh_reg_dma = shadow_reg_dma;
+
+	wqicb->len = cpu_to_le16(tx_ring->wq_len | Q_LEN_V | Q_LEN_CPP_CONT);
+	wqicb->flags = cpu_to_le16(Q_FLAGS_LC |
+				   Q_FLAGS_LB | Q_FLAGS_LI | Q_FLAGS_LO);
+	wqicb->cq_id_rss = cpu_to_le16(tx_ring->cq_id);
+	wqicb->rid = 0;
+	wqicb->addr_lo = cpu_to_le32(tx_ring->wq_base_dma);
+	wqicb->addr_hi = cpu_to_le32((u64) tx_ring->wq_base_dma >> 32);
+
+	wqicb->cnsmr_idx_addr_lo = cpu_to_le32(tx_ring->cnsmr_idx_sh_reg_dma);
+	wqicb->cnsmr_idx_addr_hi =
+	    cpu_to_le32((u64) tx_ring->cnsmr_idx_sh_reg_dma >> 32);
+
+	ql_init_tx_ring(qdev, tx_ring);
+
+	err = ql_write_cfg(qdev, wqicb, sizeof(wqicb), CFG_LRQ,
+			   (u16) tx_ring->wq_id);
+	if (err) {
+		QPRINTK(qdev, IFUP, ERR, "Failed to load tx_ring.\n");
+		return err;
+	}
+	QPRINTK(qdev, IFUP, INFO, "Successfully loaded WQICB.\n");
+	return err;
+}
+
+static void ql_disable_msix(struct ql_adapter *qdev)
+{
+	if (test_bit(QL_MSIX_ENABLED, &qdev->flags)) {
+		pci_disable_msix(qdev->pdev);
+		clear_bit(QL_MSIX_ENABLED, &qdev->flags);
+		kfree(qdev->msi_x_entry);
+		qdev->msi_x_entry = NULL;
+	} else if (test_bit(QL_MSI_ENABLED, &qdev->flags)) {
+		pci_disable_msi(qdev->pdev);
+		clear_bit(QL_MSI_ENABLED, &qdev->flags);
+	}
+}
+
+static void ql_enable_msix(struct ql_adapter *qdev)
+{
+	int i;
+
+	qdev->intr_count = 1;
+	/* Get the MSIX vectors. */
+	if (irq_type == MSIX_IRQ) {
+		/* Try to alloc space for the msix struct,
+		 * if it fails then go to MSI/legacy.
+		 */
+		qdev->msi_x_entry = kcalloc(qdev->rx_ring_count,
+					    sizeof(struct msix_entry),
+					    GFP_KERNEL);
+		if (!qdev->msi_x_entry) {
+			irq_type = MSI_IRQ;
+			goto msi;
+		}
+
+		for (i = 0; i < qdev->rx_ring_count; i++)
+			qdev->msi_x_entry[i].entry = i;
+
+		if (!pci_enable_msix
+		    (qdev->pdev, qdev->msi_x_entry, qdev->rx_ring_count)) {
+			set_bit(QL_MSIX_ENABLED, &qdev->flags);
+			qdev->intr_count = qdev->rx_ring_count;
+			QPRINTK(qdev, IFUP, INFO,
+				"MSI-X Enabled, got %d vectors.\n",
+				qdev->intr_count);
+			return;
+		} else {
+			kfree(qdev->msi_x_entry);
+			qdev->msi_x_entry = NULL;
+			QPRINTK(qdev, IFUP, WARNING,
+				"MSI-X Enable failed, trying MSI.\n");
+			irq_type = MSI_IRQ;
+		}
+	}
+msi:
+	if (irq_type == MSI_IRQ) {
+		if (!pci_enable_msi(qdev->pdev)) {
+			set_bit(QL_MSI_ENABLED, &qdev->flags);
+			QPRINTK(qdev, IFUP, INFO,
+				"Running with MSI interrupts.\n");
+			return;
+		}
+	}
+	irq_type = LEG_IRQ;
+	spin_lock_init(&qdev->legacy_lock);
+	qdev->legacy_check = ql_legacy_check;
+	QPRINTK(qdev, IFUP, DEBUG, "Running with legacy interrupts.\n");
+}
+
+/*
+ * Here we build the intr_context structures based on
+ * our rx_ring count and intr vector count.
+ * The intr_context structure is used to hook each vector
+ * to possibly different handlers.
+ */
+static void ql_resolve_queues_to_irqs(struct ql_adapter *qdev)
+{
+	int i = 0;
+	struct intr_context *intr_context = &qdev->intr_context[0];
+
+	ql_enable_msix(qdev);
+
+	if (likely(test_bit(QL_MSIX_ENABLED, &qdev->flags))) {
+		/* Each rx_ring has it's
+		 * own intr_context since we have separate
+		 * vectors for each queue.
+		 * This only true when MSI-X is enabled.
+		 */
+		for (i = 0; i < qdev->intr_count; i++, intr_context++) {
+			qdev->rx_ring[i].irq = i;
+			intr_context->intr = i;
+			intr_context->qdev = qdev;
+			/*
+			 * We set up each vectors enable/disable/read bits so
+			 * there's no bit/mask calculations in the critical path.
+			 */
+			intr_context->intr_en_mask =
+			    INTR_EN_TYPE_MASK | INTR_EN_INTR_MASK |
+			    INTR_EN_TYPE_ENABLE | INTR_EN_IHD_MASK | INTR_EN_IHD
+			    | i;
+			intr_context->intr_dis_mask =
+			    INTR_EN_TYPE_MASK | INTR_EN_INTR_MASK |
+			    INTR_EN_TYPE_DISABLE | INTR_EN_IHD_MASK |
+			    INTR_EN_IHD | i;
+			intr_context->intr_read_mask =
+			    INTR_EN_TYPE_MASK | INTR_EN_INTR_MASK |
+			    INTR_EN_TYPE_READ | INTR_EN_IHD_MASK | INTR_EN_IHD |
+			    i;
+
+			if (i == 0) {
+				/*
+				 * Default queue handles bcast/mcast plus
+				 * async events.  Needs buffers.
+				 */
+				intr_context->handler = qlge_isr;
+				sprintf(intr_context->name, "%s-default-queue",
+					qdev->ndev->name);
+			} else if (i < qdev->rss_ring_first_cq_id) {
+				/*
+				 * Outbound queue is for outbound completions only.
+				 */
+				intr_context->handler = qlge_msix_tx_isr;
+				sprintf(intr_context->name, "%s-txq-%d",
+					qdev->ndev->name, i);
+			} else {
+				/*
+				 * Inbound queues handle unicast frames only.
+				 */
+				intr_context->handler = qlge_msix_rx_isr;
+				sprintf(intr_context->name, "%s-rxq-%d",
+					qdev->ndev->name, i);
+			}
+		}
+	} else {
+		/*
+		 * All rx_rings use the same intr_context since
+		 * there is only one vector.
+		 */
+		intr_context->intr = 0;
+		intr_context->qdev = qdev;
+		/*
+		 * We set up each vectors enable/disable/read bits so
+		 * there's no bit/mask calculations in the critical path.
+		 */
+		intr_context->intr_en_mask =
+		    INTR_EN_TYPE_MASK | INTR_EN_INTR_MASK | INTR_EN_TYPE_ENABLE;
+		intr_context->intr_dis_mask =
+		    INTR_EN_TYPE_MASK | INTR_EN_INTR_MASK |
+		    INTR_EN_TYPE_DISABLE;
+		intr_context->intr_read_mask =
+		    INTR_EN_TYPE_MASK | INTR_EN_INTR_MASK | INTR_EN_TYPE_READ;
+		/*
+		 * Single interrupt means one handler for all rings.
+		 */
+		intr_context->handler = qlge_isr;
+		sprintf(intr_context->name, "%s-single_irq", qdev->ndev->name);
+		for (i = 0; i < qdev->rx_ring_count; i++)
+			qdev->rx_ring[i].irq = 0;
+	}
+}
+
+static void ql_free_irq(struct ql_adapter *qdev)
+{
+	int i;
+	struct intr_context *intr_context = &qdev->intr_context[0];
+
+	for (i = 0; i < qdev->intr_count; i++, intr_context++) {
+		if (intr_context->hooked) {
+			if (test_bit(QL_MSIX_ENABLED, &qdev->flags)) {
+				free_irq(qdev->msi_x_entry[i].vector,
+					 &qdev->rx_ring[i]);
+				QPRINTK(qdev, IFDOWN, ERR,
+					"freeing msix interrupt %d.\n", i);
+			} else {
+				free_irq(qdev->pdev->irq, &qdev->rx_ring[0]);
+				QPRINTK(qdev, IFDOWN, ERR,
+					"freeing msi interrupt %d.\n", i);
+			}
+		}
+	}
+	ql_disable_msix(qdev);
+}
+
+static int ql_request_irq(struct ql_adapter *qdev)
+{
+	int i;
+	int status = 0;
+	struct pci_dev *pdev = qdev->pdev;
+	struct intr_context *intr_context = &qdev->intr_context[0];
+
+	ql_resolve_queues_to_irqs(qdev);
+
+	for (i = 0; i < qdev->intr_count; i++, intr_context++) {
+		atomic_set(&intr_context->irq_cnt, 0);
+		if (test_bit(QL_MSIX_ENABLED, &qdev->flags)) {
+			status = request_irq(qdev->msi_x_entry[i].vector,
+					     intr_context->handler,
+					     0,
+					     intr_context->name,
+					     &qdev->rx_ring[i]);
+			if (status) {
+				QPRINTK(qdev, IFUP, ERR,
+					"Failed request for MSIX interrupt %d.\n",
+					i);
+				goto err_irq;
+			} else {
+				QPRINTK(qdev, IFUP, INFO,
+					"Hooked intr %d, queue type %s%s%s, with name %s.\n",
+					i,
+					qdev->rx_ring[i].type ==
+					DEFAULT_Q ? "DEFAULT_Q" : "",
+					qdev->rx_ring[i].type ==
+					TX_Q ? "TX_Q" : "",
+					qdev->rx_ring[i].type ==
+					RX_Q ? "RX_Q" : "", intr_context->name);
+			}
+		} else {
+			QPRINTK(qdev, IFUP, DEBUG,
+				"trying msi or legacy interrupts.\n");
+			QPRINTK(qdev, IFUP, DEBUG,
+				"%s: irq = %d.\n", __func__, pdev->irq);
+			QPRINTK(qdev, IFUP, DEBUG,
+				"%s: context->name = %s.\n", __func__,
+			       intr_context->name);
+			QPRINTK(qdev, IFUP, DEBUG,
+				"%s: dev_id = 0x%p.\n", __func__,
+			       &qdev->rx_ring[0]);
+			status =
+			    request_irq(pdev->irq, qlge_isr,
+					test_bit(QL_MSI_ENABLED,
+						 &qdev->
+						 flags) ? 0 : IRQF_SHARED,
+					intr_context->name, &qdev->rx_ring[0]);
+			if (status)
+				goto err_irq;
+
+			QPRINTK(qdev, IFUP, ERR,
+				"Hooked intr %d, queue type %s%s%s, with name %s.\n",
+				i,
+				qdev->rx_ring[0].type ==
+				DEFAULT_Q ? "DEFAULT_Q" : "",
+				qdev->rx_ring[0].type == TX_Q ? "TX_Q" : "",
+				qdev->rx_ring[0].type == RX_Q ? "RX_Q" : "",
+				intr_context->name);
+		}
+		intr_context->hooked = 1;
+	}
+	return status;
+err_irq:
+	QPRINTK(qdev, IFUP, ERR, "Failed to get the interrupts!!!/n");
+	ql_free_irq(qdev);
+	return status;
+}
+
+static int ql_start_rss(struct ql_adapter *qdev)
+{
+	struct ricb *ricb = &qdev->ricb;
+	int status = 0;
+	int i;
+	u8 *hash_id = (u8 *) ricb->hash_cq_id;
+
+	memset((void *)ricb, 0, sizeof(ricb));
+
+	ricb->base_cq = qdev->rss_ring_first_cq_id | RSS_L4K;
+	ricb->flags =
+	    (RSS_L6K | RSS_LI | RSS_LB | RSS_LM | RSS_RI4 | RSS_RI6 | RSS_RT4 |
+	     RSS_RT6);
+	ricb->mask = cpu_to_le16(qdev->rss_ring_count - 1);
+
+	/*
+	 * Fill out the Indirection Table.
+	 */
+	for (i = 0; i < 32; i++)
+		hash_id[i] = i & 1;
+
+	/*
+	 * Random values for the IPv6 and IPv4 Hash Keys.
+	 */
+	get_random_bytes((void *)&ricb->ipv6_hash_key[0], 40);
+	get_random_bytes((void *)&ricb->ipv4_hash_key[0], 16);
+
+	QPRINTK(qdev, IFUP, INFO, "Initializing RSS.\n");
+
+	status = ql_write_cfg(qdev, ricb, sizeof(ricb), CFG_LR, 0);
+	if (status) {
+		QPRINTK(qdev, IFUP, ERR, "Failed to load RICB.\n");
+		return status;
+	}
+	QPRINTK(qdev, IFUP, INFO, "Successfully loaded RICB.\n");
+	return status;
+}
+
+/* Initialize the frame-to-queue routing. */
+static int ql_route_initialize(struct ql_adapter *qdev)
+{
+	int status = 0;
+	int i;
+
+	/* Clear all the entries in the routing table. */
+	for (i = 0; i < 16; i++) {
+		status = ql_set_routing_reg(qdev, i, 0, 0);
+		if (status) {
+			QPRINTK(qdev, IFUP, ERR,
+				"Failed to init routing register for CAM packets.\n");
+			return status;
+		}
+	}
+
+	status = ql_set_routing_reg(qdev, RT_IDX_ALL_ERR_SLOT, RT_IDX_ERR, 1);
+	if (status) {
+		QPRINTK(qdev, IFUP, ERR,
+			"Failed to init routing register for error packets.\n");
+		return status;
+	}
+	status = ql_set_routing_reg(qdev, RT_IDX_BCAST_SLOT, RT_IDX_BCAST, 1);
+	if (status) {
+		QPRINTK(qdev, IFUP, ERR,
+			"Failed to init routing register for broadcast packets.\n");
+		return status;
+	}
+	/* If we have more than one inbound queue, then turn on RSS in the
+	 * routing block.
+	 */
+	if (qdev->rss_ring_count > 1) {
+		status = ql_set_routing_reg(qdev, RT_IDX_RSS_MATCH_SLOT,
+					RT_IDX_RSS_MATCH, 1);
+		if (status) {
+			QPRINTK(qdev, IFUP, ERR,
+				"Failed to init routing register for MATCH RSS packets.\n");
+			return status;
+		}
+	}
+
+	status = ql_set_routing_reg(qdev, RT_IDX_CAM_HIT_SLOT,
+				    RT_IDX_CAM_HIT, 1);
+	if (status) {
+		QPRINTK(qdev, IFUP, ERR,
+			"Failed to init routing register for CAM packets.\n");
+		return status;
+	}
+	return status;
+}
+
+static int ql_adapter_initialize(struct ql_adapter *qdev)
+{
+	u32 value, mask;
+	int i;
+	int status = 0;
+
+	/*
+	 * Set up the System register to halt on errors.
+	 */
+	value = SYS_EFE | SYS_FAE;
+	mask = value << 16;
+	ql_write32(qdev, SYS, mask | value);
+
+	/* Set the default queue. */
+	value = NIC_RCV_CFG_DFQ;
+	mask = NIC_RCV_CFG_DFQ_MASK;
+	ql_write32(qdev, NIC_RCV_CFG, (mask | value));
+
+	/* Set the MPI interrupt to enabled. */
+	ql_write32(qdev, INTR_MASK, (INTR_MASK_PI << 16) | INTR_MASK_PI);
+
+	/* Enable the function, set pagesize, enable error checking. */
+	value = FSC_FE | FSC_EPC_INBOUND | FSC_EPC_OUTBOUND |
+	    FSC_EC | FSC_VM_PAGE_4K | FSC_SH;
+
+	/* Set/clear header splitting. */
+	mask = FSC_VM_PAGESIZE_MASK |
+	    FSC_DBL_MASK | FSC_DBRST_MASK | (value << 16);
+	ql_write32(qdev, FSC, mask | value);
+
+	ql_write32(qdev, SPLT_HDR, SPLT_HDR_EP |
+		min(SMALL_BUFFER_SIZE, MAX_SPLIT_SIZE));
+
+	/* Start up the rx queues. */
+	for (i = 0; i < qdev->rx_ring_count; i++) {
+		status = ql_start_rx_ring(qdev, &qdev->rx_ring[i]);
+		if (status) {
+			QPRINTK(qdev, IFUP, ERR,
+				"Failed to start rx ring[%d].\n", i);
+			return status;
+		}
+	}
+
+	/* If there is more than one inbound completion queue
+	 * then download a RICB to configure RSS.
+	 */
+	if (qdev->rss_ring_count > 1) {
+		status = ql_start_rss(qdev);
+		if (status) {
+			QPRINTK(qdev, IFUP, ERR, "Failed to start RSS.\n");
+			return status;
+		}
+	}
+
+	/* Start up the tx queues. */
+	for (i = 0; i < qdev->tx_ring_count; i++) {
+		status = ql_start_tx_ring(qdev, &qdev->tx_ring[i]);
+		if (status) {
+			QPRINTK(qdev, IFUP, ERR,
+				"Failed to start tx ring[%d].\n", i);
+			return status;
+		}
+	}
+
+	status = ql_port_initialize(qdev);
+	if (status) {
+		QPRINTK(qdev, IFUP, ERR, "Failed to start port.\n");
+		return status;
+	}
+
+	status = ql_set_mac_addr_reg(qdev, (u8 *) qdev->ndev->perm_addr,
+				     MAC_ADDR_TYPE_CAM_MAC, qdev->func);
+	if (status) {
+		QPRINTK(qdev, IFUP, ERR, "Failed to init mac address.\n");
+		return status;
+	}
+
+	status = ql_route_initialize(qdev);
+	if (status) {
+		QPRINTK(qdev, IFUP, ERR, "Failed to init routing table.\n");
+		return status;
+	}
+
+	/* Start NAPI for the RSS queues. */
+	for (i = qdev->rss_ring_first_cq_id; i < qdev->rx_ring_count; i++) {
+		QPRINTK(qdev, IFUP, INFO, "Enabling NAPI for rx_ring[%d].\n",
+			i);
+		napi_enable(&qdev->rx_ring[i].napi);
+	}
+
+	return status;
+}
+
+/* Issue soft reset to chip. */
+static int ql_adapter_reset(struct ql_adapter *qdev)
+{
+	u32 value;
+	int max_wait_time;
+	int status = 0;
+	int resetCnt = 0;
+
+#define MAX_RESET_CNT   1
+issueReset:
+	resetCnt++;
+	QPRINTK(qdev, IFDOWN, DEBUG, "Issue soft reset to chip.\n");
+	ql_write32(qdev, RST_FO, (RST_FO_FR << 16) | RST_FO_FR);
+	/* Wait for reset to complete. */
+	max_wait_time = 3;
+	QPRINTK(qdev, IFDOWN, DEBUG, "Wait %d seconds for reset to complete.\n",
+		max_wait_time);
+	do {
+		value = ql_read32(qdev, RST_FO);
+		if ((value & RST_FO_FR) == 0)
+			break;
+
+		ssleep(1);
+	} while ((--max_wait_time));
+	if (value & RST_FO_FR) {
+		QPRINTK(qdev, IFDOWN, ERR,
+			"Stuck in SoftReset:  FSC_SR:0x%08x\n", value);
+		if (resetCnt < MAX_RESET_CNT)
+			goto issueReset;
+	}
+	if (max_wait_time == 0) {
+		status = -ETIMEDOUT;
+		QPRINTK(qdev, IFDOWN, ERR,
+			"ETIMEOUT!!! errored out of resetting the chip!\n");
+	}
+
+	return status;
+}
+
+static void ql_display_dev_info(struct net_device *ndev)
+{
+	struct ql_adapter *qdev = (struct ql_adapter *)netdev_priv(ndev);
+
+	QPRINTK(qdev, PROBE, INFO,
+		"Function #%d, NIC Roll %d, NIC Rev = %d, "
+		"XG Roll = %d, XG Rev = %d.\n",
+		qdev->func,
+		qdev->chip_rev_id & 0x0000000f,
+		qdev->chip_rev_id >> 4 & 0x0000000f,
+		qdev->chip_rev_id >> 8 & 0x0000000f,
+		qdev->chip_rev_id >> 12 & 0x0000000f);
+	QPRINTK(qdev, PROBE, INFO,
+		"MAC address %02x:%02x:%02x:%02x:%02x:%02x\n",
+		ndev->dev_addr[0], ndev->dev_addr[1],
+		ndev->dev_addr[2], ndev->dev_addr[3], ndev->dev_addr[4],
+		ndev->dev_addr[5]);
+}
+
+static int ql_adapter_down(struct ql_adapter *qdev)
+{
+	struct net_device *ndev = qdev->ndev;
+	int i, status = 0;
+	struct rx_ring *rx_ring;
+
+	netif_stop_queue(ndev);
+	netif_carrier_off(ndev);
+
+	cancel_delayed_work_sync(&qdev->asic_reset_work);
+	cancel_delayed_work_sync(&qdev->mpi_reset_work);
+	cancel_delayed_work_sync(&qdev->mpi_work);
+
+	/* The default queue at index 0 is always processed in
+	 * a workqueue.
+	 */
+	cancel_delayed_work_sync(&qdev->rx_ring[0].rx_work);
+
+	/* The rest of the rx_rings are processed in
+	 * a workqueue only if it's a single interrupt
+	 * environment (MSI/Legacy).
+	 */
+	for (i = 1; i > qdev->rx_ring_count; i++) {
+		rx_ring = &qdev->rx_ring[i];
+		/* Only the RSS rings use NAPI on multi irq
+		 * environment.  Outbound completion processing
+		 * is done in interrupt context.
+		 */
+		if (i >= qdev->rss_ring_first_cq_id) {
+			napi_disable(&rx_ring->napi);
+		} else {
+			cancel_delayed_work_sync(&rx_ring->rx_work);
+		}
+	}
+
+	clear_bit(QL_ADAPTER_UP, &qdev->flags);
+
+	ql_disable_interrupts(qdev);
+
+	ql_tx_ring_clean(qdev);
+
+	spin_lock(&qdev->hw_lock);
+	status = ql_adapter_reset(qdev);
+	if (status) {
+		QPRINTK(qdev, IFDOWN, ERR, "reset(func #%d) FAILED!\n",
+			qdev->func);
+		goto out;
+	}
+
+	QPRINTK(qdev, IFDOWN, INFO, "reset(func #%d) success!\n", qdev->func);
+out:
+	spin_unlock(&qdev->hw_lock);
+	return status;
+}
+
+static int ql_adapter_up(struct ql_adapter *qdev)
+{
+	int err = 0;
+
+	spin_lock(&qdev->hw_lock);
+	err = ql_adapter_initialize(qdev);
+	if (err) {
+		QPRINTK(qdev, IFUP, INFO, "Unable to initialize adapter.\n");
+		spin_unlock(&qdev->hw_lock);
+		goto err_init;
+	}
+	spin_unlock(&qdev->hw_lock);
+	set_bit(QL_ADAPTER_UP, &qdev->flags);
+	ql_enable_interrupts(qdev);
+	ql_enable_all_completion_interrupts(qdev);
+	if ((ql_read32(qdev, STS) & qdev->port_init)) {
+		netif_carrier_on(qdev->ndev);
+		netif_start_queue(qdev->ndev);
+	}
+
+	return 0;
+err_init:
+	ql_adapter_reset(qdev);
+	return err;
+}
+
+static int ql_cycle_adapter(struct ql_adapter *qdev)
+{
+	int status;
+
+	status = ql_adapter_down(qdev);
+	if (status)
+		goto error;
+
+	status = ql_adapter_up(qdev);
+	if (status)
+		goto error;
+
+	return status;
+error:
+	QPRINTK(qdev, IFUP, ALERT,
+		"Driver up/down cycle failed, closing device\n");
+	rtnl_lock();
+	dev_close(qdev->ndev);
+	rtnl_unlock();
+	return status;
+}
+
+static void ql_release_adapter_resources(struct ql_adapter *qdev)
+{
+	ql_free_mem_resources(qdev);
+	ql_free_irq(qdev);
+}
+
+static int ql_get_adapter_resources(struct ql_adapter *qdev)
+{
+	int status = 0;
+
+	if (ql_alloc_mem_resources(qdev)) {
+		QPRINTK(qdev, IFUP, ERR, "Unable to  allocate memory.\n");
+		return -ENOMEM;
+	}
+	status = ql_request_irq(qdev);
+	if (status)
+		goto err_irq;
+	return status;
+err_irq:
+	ql_free_mem_resources(qdev);
+	return status;
+}
+
+static int qlge_close(struct net_device *ndev)
+{
+	struct ql_adapter *qdev = netdev_priv(ndev);
+
+	/*
+	 * Wait for device to recover from a reset.
+	 * (Rarely happens, but possible.)
+	 */
+	while (!test_bit(QL_ADAPTER_UP, &qdev->flags))
+		msleep(MSLEEP_DELAY);
+	ql_adapter_down(qdev);
+	ql_release_adapter_resources(qdev);
+	ql_free_ring_cb(qdev);
+	return 0;
+}
+
+static int ql_configure_rings(struct ql_adapter *qdev)
+{
+	int i;
+	struct rx_ring *rx_ring;
+	struct tx_ring *tx_ring;
+	int cpu_cnt = num_online_cpus();
+
+	/*
+	 * For each processor present we allocate one
+	 * rx_ring for outbound completions, and one
+	 * rx_ring for inbound completions.  Plus there is
+	 * always the one default queue.  For the CPU
+	 * counts we end up with the following rx_rings:
+	 * rx_ring count =
+	 *  one default queue +
+	 *  (CPU count * outbound completion rx_ring) +
+	 *  (CPU count * inbound (RSS) completion rx_ring)
+	 * To keep it simple we limit the total number of
+	 * queues to < 32, so we truncate CPU to 8.
+	 * This limitation can be removed when requested.
+	 */
+
+	if (cpu_cnt > 8)
+		cpu_cnt = 8;
+
+	/*
+	 * rx_ring[0] is always the default queue.
+	 */
+	/* Allocate outbound completion ring for each CPU. */
+	qdev->tx_ring_count = cpu_cnt;
+	/* Allocate inbound completion (RSS) ring for each CPU. */
+	qdev->rss_ring_count = cpu_cnt;
+	/* cq_id for the first inbound ring handler. */
+	qdev->rss_ring_first_cq_id = cpu_cnt + 1;
+	/*
+	 * qdev->rx_ring_count:
+	 * Total number of rx_rings.  This includes the one
+	 * default queue, a number of outbound completion
+	 * handler rx_rings, and the number of inbound
+	 * completion handler rx_rings.
+	 */
+	qdev->rx_ring_count = qdev->tx_ring_count + qdev->rss_ring_count + 1;
+
+	if (ql_alloc_ring_cb(qdev))
+		return -ENOMEM;
+
+	for (i = 0; i < qdev->tx_ring_count; i++) {
+		tx_ring = &qdev->tx_ring[i];
+		memset((void *)tx_ring, 0, sizeof(tx_ring));
+		tx_ring->qdev = qdev;
+		tx_ring->wq_id = i;
+		tx_ring->wq_len = qdev->tx_ring_size;
+		tx_ring->wq_size =
+		    tx_ring->wq_len * sizeof(struct ob_mac_iocb_req);
+
+		/*
+		 * The completion queue ID for the tx rings start
+		 * immediately after the default Q ID, which is zero.
+		 */
+		tx_ring->cq_id = i + 1;
+	}
+
+	for (i = 0; i < qdev->rx_ring_count; i++) {
+		rx_ring = &qdev->rx_ring[i];
+		memset((void *)rx_ring, 0, sizeof(rx_ring));
+		rx_ring->qdev = qdev;
+		rx_ring->cq_id = i;
+		rx_ring->cpu = i % cpu_cnt;	/* CPU to run handler on. */
+		if (i == 0) {	/* Default queue at index 0. */
+			/*
+			 * Default queue handles bcast/mcast plus
+			 * async events.  Needs buffers.
+			 */
+			rx_ring->cq_len = qdev->rx_ring_size;
+			rx_ring->cq_size =
+			    rx_ring->cq_len * sizeof(struct ql_net_rsp_iocb);
+			rx_ring->lbq_len = NUM_LARGE_BUFFERS;
+			rx_ring->lbq_size =
+			    rx_ring->lbq_len * sizeof(struct bq_element);
+			rx_ring->lbq_buf_size = LARGE_BUFFER_SIZE;
+			rx_ring->sbq_len = NUM_SMALL_BUFFERS;
+			rx_ring->sbq_size =
+			    rx_ring->sbq_len * sizeof(struct bq_element);
+			rx_ring->sbq_buf_size = SMALL_BUFFER_SIZE * 2;
+			rx_ring->type = DEFAULT_Q;
+		} else if (i < qdev->rss_ring_first_cq_id) {
+			/*
+			 * Outbound queue handles outbound completions only.
+			 */
+			/* outbound cq is same size as tx_ring it services. */
+			rx_ring->cq_len = qdev->tx_ring_size;
+			rx_ring->cq_size =
+			    rx_ring->cq_len * sizeof(struct ql_net_rsp_iocb);
+			rx_ring->lbq_len = 0;
+			rx_ring->lbq_size = 0;
+			rx_ring->lbq_buf_size = 0;
+			rx_ring->sbq_len = 0;
+			rx_ring->sbq_size = 0;
+			rx_ring->sbq_buf_size = 0;
+			rx_ring->type = TX_Q;
+		} else {	/* Inbound completions (RSS) queues */
+			/*
+			 * Inbound queues handle unicast frames only.
+			 */
+			rx_ring->cq_len = qdev->rx_ring_size;
+			rx_ring->cq_size =
+			    rx_ring->cq_len * sizeof(struct ql_net_rsp_iocb);
+			rx_ring->lbq_len = NUM_LARGE_BUFFERS;
+			rx_ring->lbq_size =
+			    rx_ring->lbq_len * sizeof(struct bq_element);
+			rx_ring->lbq_buf_size = LARGE_BUFFER_SIZE;
+			rx_ring->sbq_len = NUM_SMALL_BUFFERS;
+			rx_ring->sbq_size =
+			    rx_ring->sbq_len * sizeof(struct bq_element);
+			rx_ring->sbq_buf_size = SMALL_BUFFER_SIZE * 2;
+			rx_ring->type = RX_Q;
+		}
+	}
+	return 0;
+}
+
+static int qlge_open(struct net_device *ndev)
+{
+	int err = 0;
+	struct ql_adapter *qdev = netdev_priv(ndev);
+
+	err = ql_configure_rings(qdev);
+	if (err)
+		return err;
+
+	err = ql_get_adapter_resources(qdev);
+	if (err)
+		goto error_resource;
+
+	err = ql_adapter_up(qdev);
+	if (err)
+		goto error_up;
+
+	return err;
+
+error_resource:
+	ql_free_ring_cb(qdev);
+error_up:
+	ql_release_adapter_resources(qdev);
+	QL_DUMP_ALL(qdev);
+	return err;
+}
+
+static int qlge_change_mtu(struct net_device *ndev, int new_mtu)
+{
+	struct ql_adapter *qdev = netdev_priv(ndev);
+
+	if (ndev->mtu == 1500 && new_mtu == 9000) {
+		QPRINTK(qdev, IFUP, ERR, "Changing to jumbo MTU.\n");
+	} else if (ndev->mtu == 9000 && new_mtu == 1500) {
+		QPRINTK(qdev, IFUP, ERR, "Changing to normal MTU.\n");
+	} else if ((ndev->mtu == 1500 && new_mtu == 1500) ||
+		   (ndev->mtu == 9000 && new_mtu == 9000)) {
+		return 0;
+	} else
+		return -EINVAL;
+	ndev->mtu = new_mtu;
+	return 0;
+}
+
+static struct net_device_stats *qlge_get_stats(struct net_device
+					       *ndev)
+{
+	struct ql_adapter *qdev = netdev_priv(ndev);
+	return &qdev->stats;
+}
+
+static void qlge_set_multicast_list(struct net_device *ndev)
+{
+	struct ql_adapter *qdev = (struct ql_adapter *)netdev_priv(ndev);
+	struct dev_mc_list *mc_ptr;
+	int i;
+
+	/*
+	 * Set or clear promiscuous mode if a
+	 * transition is taking place.
+	 */
+	if (ndev->flags & IFF_PROMISC) {
+		if (!test_bit(QL_PROMISCUOUS, &qdev->flags)) {
+			if (ql_set_routing_reg
+			    (qdev, RT_IDX_PROMISCUOUS_SLOT, RT_IDX_VALID, 1)) {
+				QPRINTK(qdev, HW, ERR,
+					"Failed to set promiscous mode.\n");
+			} else {
+				set_bit(QL_PROMISCUOUS, &qdev->flags);
+			}
+		}
+	} else {
+		if (test_bit(QL_PROMISCUOUS, &qdev->flags)) {
+			if (ql_set_routing_reg
+			    (qdev, RT_IDX_PROMISCUOUS_SLOT, RT_IDX_VALID, 0)) {
+				QPRINTK(qdev, HW, ERR,
+					"Failed to clear promiscous mode.\n");
+			} else {
+				clear_bit(QL_PROMISCUOUS, &qdev->flags);
+			}
+		}
+	}
+
+	/*
+	 * Set or clear all multicast mode if a
+	 * transition is taking place.
+	 */
+	if ((ndev->flags & IFF_ALLMULTI) ||
+	    (ndev->mc_count > MAX_MULTICAST_ENTRIES)) {
+		if (!test_bit(QL_ALLMULTI, &qdev->flags)) {
+			if (ql_set_routing_reg
+			    (qdev, RT_IDX_ALLMULTI_SLOT, RT_IDX_MCAST, 1)) {
+				QPRINTK(qdev, HW, ERR,
+					"Failed to set all-multi mode.\n");
+			} else {
+				set_bit(QL_ALLMULTI, &qdev->flags);
+			}
+		}
+	} else {
+		if (test_bit(QL_ALLMULTI, &qdev->flags)) {
+			if (ql_set_routing_reg
+			    (qdev, RT_IDX_ALLMULTI_SLOT, RT_IDX_MCAST, 0)) {
+				QPRINTK(qdev, HW, ERR,
+					"Failed to clear all-multi mode.\n");
+			} else {
+				clear_bit(QL_ALLMULTI, &qdev->flags);
+			}
+		}
+	}
+
+	if (ndev->mc_count) {
+		for (i = 0, mc_ptr = ndev->mc_list; mc_ptr;
+		     i++, mc_ptr = mc_ptr->next)
+			if (ql_set_mac_addr_reg(qdev, (u8 *) mc_ptr->dmi_addr,
+						MAC_ADDR_TYPE_MULTI_MAC, i)) {
+				QPRINTK(qdev, HW, ERR,
+					"Failed to loadmulticast address.\n");
+				return;
+			}
+		if (ql_set_routing_reg
+		    (qdev, RT_IDX_MCAST_MATCH_SLOT, RT_IDX_MCAST_MATCH, 1)) {
+			QPRINTK(qdev, HW, ERR,
+				"Failed to set multicast match mode.\n");
+		} else {
+			set_bit(QL_ALLMULTI, &qdev->flags);
+		}
+	}
+}
+
+static int qlge_set_mac_address(struct net_device *ndev, void *p)
+{
+	struct ql_adapter *qdev = (struct ql_adapter *)netdev_priv(ndev);
+	struct sockaddr *addr = p;
+	unsigned long hw_flags;
+
+	if (netif_running(ndev))
+		return -EBUSY;
+
+	if (!is_valid_ether_addr(addr->sa_data))
+		return -EADDRNOTAVAIL;
+	memcpy(ndev->dev_addr, addr->sa_data, ndev->addr_len);
+
+	spin_lock_irqsave(&qdev->hw_lock, hw_flags);
+	if (ql_set_mac_addr_reg(qdev, (u8 *) ndev->dev_addr,
+				MAC_ADDR_TYPE_CAM_MAC, qdev->func)) {/* Unicast */
+		QPRINTK(qdev, HW, ERR, "Failed to load MAC address.\n");
+		return -1;
+	}
+	spin_unlock_irqrestore(&qdev->hw_lock, hw_flags);
+
+	return 0;
+}
+
+static void qlge_tx_timeout(struct net_device *ndev)
+{
+	struct ql_adapter *qdev = (struct ql_adapter *)netdev_priv(ndev);
+	queue_delayed_work(qdev->workqueue, &qdev->asic_reset_work, 0);
+}
+
+static void ql_asic_reset_work(struct work_struct *work)
+{
+	struct ql_adapter *qdev =
+	    container_of(work, struct ql_adapter, asic_reset_work.work);
+	ql_cycle_adapter(qdev);
+}
+
+static void ql_get_board_info(struct ql_adapter *qdev)
+{
+	qdev->func =
+	    (ql_read32(qdev, STS) & STS_FUNC_ID_MASK) >> STS_FUNC_ID_SHIFT;
+	if (qdev->func) {
+		qdev->xg_sem_mask = SEM_XGMAC1_MASK;
+		qdev->port_link_up = STS_PL1;
+		qdev->port_init = STS_PI1;
+		qdev->mailbox_in = PROC_ADDR_MPI_RISC | PROC_ADDR_FUNC2_MBI;
+		qdev->mailbox_out = PROC_ADDR_MPI_RISC | PROC_ADDR_FUNC2_MBO;
+	} else {
+		qdev->xg_sem_mask = SEM_XGMAC0_MASK;
+		qdev->port_link_up = STS_PL0;
+		qdev->port_init = STS_PI0;
+		qdev->mailbox_in = PROC_ADDR_MPI_RISC | PROC_ADDR_FUNC0_MBI;
+		qdev->mailbox_out = PROC_ADDR_MPI_RISC | PROC_ADDR_FUNC0_MBO;
+	}
+	qdev->chip_rev_id = ql_read32(qdev, REV_ID);
+}
+
+static void ql_release_all(struct pci_dev *pdev)
+{
+	struct net_device *ndev = pci_get_drvdata(pdev);
+	struct ql_adapter *qdev = netdev_priv(ndev);
+
+	if (qdev->workqueue) {
+		destroy_workqueue(qdev->workqueue);
+		qdev->workqueue = NULL;
+	}
+	if (qdev->q_workqueue) {
+		destroy_workqueue(qdev->q_workqueue);
+		qdev->q_workqueue = NULL;
+	}
+	if (qdev->reg_base)
+		iounmap((void *)qdev->reg_base);
+	if (qdev->doorbell_area)
+		iounmap(qdev->doorbell_area);
+	pci_release_regions(pdev);
+	pci_set_drvdata(pdev, NULL);
+}
+
+static int __devinit ql_init_device(struct pci_dev *pdev,
+				    struct net_device *ndev, int cards_found)
+{
+	struct ql_adapter *qdev = netdev_priv(ndev);
+	int pos, err = 0;
+	u16 val16;
+
+	memset((void *)qdev, 0, sizeof(qdev));
+	err = pci_enable_device(pdev);
+	if (err) {
+		dev_err(&pdev->dev, "PCI device enable failed.\n");
+		return err;
+	}
+
+	pos = pci_find_capability(pdev, PCI_CAP_ID_EXP);
+	if (pos <= 0) {
+		dev_err(&pdev->dev, PFX "Cannot find PCI Express capability, "
+			"aborting.\n");
+		goto err_out;
+	} else {
+		pci_read_config_word(pdev, pos + PCI_EXP_DEVCTL, &val16);
+		val16 &= ~PCI_EXP_DEVCTL_NOSNOOP_EN;
+		val16 |= (PCI_EXP_DEVCTL_CERE |
+			  PCI_EXP_DEVCTL_NFERE |
+			  PCI_EXP_DEVCTL_FERE | PCI_EXP_DEVCTL_URRE);
+		pci_write_config_word(pdev, pos + PCI_EXP_DEVCTL, val16);
+	}
+
+	err = pci_request_regions(pdev, DRV_NAME);
+	if (err) {
+		dev_err(&pdev->dev, "PCI region request failed.\n");
+		goto err_out;
+	}
+
+	pci_set_master(pdev);
+	if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
+		set_bit(QL_DMA64, &qdev->flags);
+		err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
+	} else {
+		err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
+		if (!err)
+		       err = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
+	}
+
+	if (err) {
+		dev_err(&pdev->dev, "No usable DMA configuration.\n");
+		goto err_out;
+	}
+
+	pci_set_drvdata(pdev, ndev);
+	qdev->reg_base =
+	    ioremap_nocache(pci_resource_start(pdev, 1),
+			    pci_resource_len(pdev, 1));
+	if (!qdev->reg_base) {
+		dev_err(&pdev->dev, "Register mapping failed.\n");
+		err = -ENOMEM;
+		goto err_out;
+	}
+
+	qdev->doorbell_area_size = pci_resource_len(pdev, 3);
+	qdev->doorbell_area =
+	    ioremap_nocache(pci_resource_start(pdev, 3),
+			    pci_resource_len(pdev, 3));
+	if (!qdev->doorbell_area) {
+		dev_err(&pdev->dev, "Doorbell register mapping failed.\n");
+		err = -ENOMEM;
+		goto err_out;
+	}
+
+	ql_get_board_info(qdev);
+	qdev->ndev = ndev;
+	qdev->pdev = pdev;
+	qdev->msg_enable = netif_msg_init(debug, default_msg);
+	spin_lock_init(&qdev->hw_lock);
+	spin_lock_init(&qdev->stats_lock);
+
+	/* make sure the EEPROM is good */
+	err = ql_get_flash_params(qdev);
+	if (err) {
+		dev_err(&pdev->dev, "Invalid FLASH.\n");
+		goto err_out;
+	}
+#if 0
+	/*
+	 * Flash parameters are TBD.
+	 */
+#else
+	if (!cards_found) {
+		u8 addr[6] = { 0x00, 0xc0, 0xdd, 0x03, 0xda, 0x39 };
+		memcpy(ndev->dev_addr, &addr, ETH_ALEN);
+	} else {
+		u8 addr[6] = { 0x00, 0xc0, 0xdd, 0x03, 0xda, 0x3a };
+		memcpy(ndev->dev_addr, &addr, ETH_ALEN);
+	}
+#endif
+	memcpy(ndev->perm_addr, ndev->dev_addr, ndev->addr_len);
+
+	/* Set up the default ring sizes. */
+	qdev->tx_ring_size = NUM_TX_RING_ENTRIES;
+	qdev->rx_ring_size = NUM_RX_RING_ENTRIES;
+
+	/* Set up the coalescing parameters. */
+	qdev->rx_coalesce_usecs = DFLT_COALESCE_WAIT;
+	qdev->tx_coalesce_usecs = DFLT_COALESCE_WAIT;
+	qdev->rx_max_coalesced_frames = DFLT_INTER_FRAME_WAIT;
+	qdev->tx_max_coalesced_frames = DFLT_INTER_FRAME_WAIT;
+
+	/*
+	 * Set up the operating parameters.
+	 */
+	qdev->rx_csum = 1;
+
+	qdev->q_workqueue = create_workqueue(ndev->name);
+	qdev->workqueue = create_singlethread_workqueue(ndev->name);
+	INIT_DELAYED_WORK(&qdev->asic_reset_work, ql_asic_reset_work);
+	INIT_DELAYED_WORK(&qdev->mpi_reset_work, ql_mpi_reset_work);
+	INIT_DELAYED_WORK(&qdev->mpi_work, ql_mpi_work);
+
+	if (!cards_found) {
+		dev_info(&pdev->dev, "%s\n", DRV_STRING);
+		dev_info(&pdev->dev, "Driver name: %s, Version: %s.\n",
+			 DRV_NAME, DRV_VERSION);
+	}
+	return 0;
+err_out:
+	ql_release_all(pdev);
+	pci_disable_device(pdev);
+	return err;
+}
+
+static int __devinit qlge_probe(struct pci_dev *pdev,
+				const struct pci_device_id *pci_entry)
+{
+	struct net_device *ndev = NULL;
+	struct ql_adapter *qdev = NULL;
+	static int cards_found = 0;
+	int err = 0;
+
+	ndev = alloc_etherdev(sizeof(struct ql_adapter));
+	if (!ndev)
+		return -ENOMEM;
+
+	err = ql_init_device(pdev, ndev, cards_found);
+	if (err < 0) {
+		free_netdev(ndev);
+		return err;
+	}
+
+	qdev = netdev_priv(ndev);
+	SET_NETDEV_DEV(ndev, &pdev->dev);
+	ndev->features = (0
+			  | NETIF_F_IP_CSUM
+			  | NETIF_F_SG
+			  | NETIF_F_TSO
+			  | NETIF_F_TSO6
+			  | NETIF_F_TSO_ECN
+			  | NETIF_F_HW_VLAN_TX
+			  | NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_FILTER);
+
+	if (test_bit(QL_DMA64, &qdev->flags))
+		ndev->features |= NETIF_F_HIGHDMA;
+
+	/*
+	 * Set up net_device structure.
+	 */
+	ndev->tx_queue_len = qdev->tx_ring_size;
+	ndev->irq = pdev->irq;
+	ndev->open = qlge_open;
+	ndev->stop = qlge_close;
+	ndev->hard_start_xmit = qlge_send;
+	SET_ETHTOOL_OPS(ndev, &qlge_ethtool_ops);
+	ndev->change_mtu = qlge_change_mtu;
+	ndev->get_stats = qlge_get_stats;
+	ndev->set_multicast_list = qlge_set_multicast_list;
+	ndev->set_mac_address = qlge_set_mac_address;
+	ndev->tx_timeout = qlge_tx_timeout;
+	ndev->watchdog_timeo = 10 * HZ;
+	ndev->vlan_rx_register = ql_vlan_rx_register;
+	ndev->vlan_rx_add_vid = ql_vlan_rx_add_vid;
+	ndev->vlan_rx_kill_vid = ql_vlan_rx_kill_vid;
+	err = register_netdev(ndev);
+	if (err) {
+		dev_err(&pdev->dev, "net device registration failed.\n");
+		ql_release_all(pdev);
+		pci_disable_device(pdev);
+		return err;
+	}
+	netif_carrier_off(ndev);
+	netif_stop_queue(ndev);
+	ql_display_dev_info(ndev);
+	cards_found++;
+	return 0;
+}
+
+static void __devexit qlge_remove(struct pci_dev *pdev)
+{
+	struct net_device *ndev = pci_get_drvdata(pdev);
+	unregister_netdev(ndev);
+	ql_release_all(pdev);
+	pci_disable_device(pdev);
+	free_netdev(ndev);
+}
+
+/*
+ * This callback is called by the PCI subsystem whenever
+ * a PCI bus error is detected.
+ */
+static pci_ers_result_t qlge_io_error_detected(struct pci_dev *pdev,
+					       enum pci_channel_state state)
+{
+	struct net_device *ndev = pci_get_drvdata(pdev);
+	struct ql_adapter *qdev = netdev_priv(ndev);
+
+	printk(KERN_ERR "%s: Enter, pdev = 0x%p.\n", __func__, pdev);
+	if (netif_running(ndev))
+		ql_adapter_down(qdev);
+
+	pci_disable_device(pdev);
+
+	/* Request a slot reset. */
+	return PCI_ERS_RESULT_NEED_RESET;
+}
+
+/*
+ * This callback is called after the PCI buss has been reset.
+ * Basically, this tries to restart the card from scratch.
+ * This is a shortened version of the device probe/discovery code,
+ * it resembles the first-half of the () routine.
+ */
+static pci_ers_result_t qlge_io_slot_reset(struct pci_dev *pdev)
+{
+	struct net_device *ndev = pci_get_drvdata(pdev);
+	struct ql_adapter *qdev = netdev_priv(ndev);
+
+	printk(KERN_ERR "%s: Enter, pdev = 0x%p.\n", __func__, pdev);
+	if (pci_enable_device(pdev)) {
+		QPRINTK(qdev, IFUP, ERR,
+			"Cannot re-enable PCI device after reset.\n");
+		return PCI_ERS_RESULT_DISCONNECT;
+	}
+
+	pci_set_master(pdev);
+
+	netif_carrier_off(ndev);
+	netif_stop_queue(ndev);
+	ql_adapter_reset(qdev);
+
+	/* Make sure the EEPROM is good */
+	memcpy(ndev->perm_addr, ndev->dev_addr, ndev->addr_len);
+
+	if (!is_valid_ether_addr(ndev->perm_addr)) {
+		QPRINTK(qdev, IFUP, ERR, "After reset, invalid MAC address.\n");
+		return PCI_ERS_RESULT_DISCONNECT;
+	}
+
+	return PCI_ERS_RESULT_RECOVERED;
+}
+
+static void qlge_io_resume(struct pci_dev *pdev)
+{
+	struct net_device *ndev = pci_get_drvdata(pdev);
+	struct ql_adapter *qdev = netdev_priv(ndev);
+
+	printk(KERN_ERR "%s: Enter, pdev = 0x%p.\n", __func__, pdev);
+	pci_set_master(pdev);
+
+	if (netif_running(ndev)) {
+		if (ql_adapter_up(qdev)) {
+			QPRINTK(qdev, IFUP, ERR,
+				"Device initialization failed after reset.\n");
+			return;
+		}
+	}
+
+	netif_device_attach(ndev);
+}
+
+static struct pci_error_handlers qlge_err_handler = {
+	.error_detected = qlge_io_error_detected,
+	.slot_reset = qlge_io_slot_reset,
+	.resume = qlge_io_resume,
+};
+
+static int qlge_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+	struct net_device *ndev = pci_get_drvdata(pdev);
+	struct ql_adapter *qdev = netdev_priv(ndev);
+	int err;
+
+	printk(KERN_ERR "%s: Enter, pdev = 0x%p, qdev = 0x%p.\n", __func__,
+	       pdev, qdev);
+
+	netif_device_detach(ndev);
+
+	if (netif_running(ndev)) {
+		err = ql_adapter_down(qdev);
+		if (!err)
+			return err;
+	}
+
+	err = pci_save_state(pdev);
+	if (err)
+		return err;
+
+	pci_disable_device(pdev);
+
+	pci_set_power_state(pdev, pci_choose_state(pdev, state));
+
+	return 0;
+}
+
+static int qlge_resume(struct pci_dev *pdev)
+{
+	struct net_device *ndev = pci_get_drvdata(pdev);
+	struct ql_adapter *qdev = netdev_priv(ndev);
+	int err;
+
+	printk(KERN_ERR "%s: Enter, pdev = 0x%p.\n", __func__, pdev);
+
+	pci_set_power_state(pdev, PCI_D0);
+	pci_restore_state(pdev);
+	err = pci_enable_device(pdev);
+	if (err) {
+		printk(KERN_ERR "%s: Cannot enable PCI device from suspend\n",
+		       __func__);
+		return err;
+	}
+	pci_set_master(pdev);
+
+	pci_enable_wake(pdev, PCI_D3hot, 0);
+	pci_enable_wake(pdev, PCI_D3cold, 0);
+
+	if (netif_running(ndev)) {
+		err = ql_adapter_up(qdev);
+		if (err)
+			return err;
+	}
+
+	netif_device_attach(ndev);
+
+	return 0;
+}
+
+static void qlge_shutdown(struct pci_dev *pdev)
+{
+	printk(KERN_ERR "%s: Enter, pdev = 0x%p.\n", __func__, pdev);
+	qlge_suspend(pdev, PMSG_SUSPEND);
+}
+
+static struct pci_driver qlge_driver = {
+	.name = DRV_NAME,
+	.id_table = qlge_pci_tbl,
+	.probe = qlge_probe,
+	.remove = __devexit_p(qlge_remove),
+#ifdef CONFIG_PM
+	.suspend = qlge_suspend,
+	.resume = qlge_resume,
+#endif
+	.shutdown = qlge_shutdown,
+	.err_handler = &qlge_err_handler
+};
+
+static int __init qlge_init_module(void)
+{
+	return pci_register_driver(&qlge_driver);
+}
+
+static void __exit qlge_exit(void)
+{
+	pci_unregister_driver(&qlge_driver);
+}
+
+module_init(qlge_init_module);
+module_exit(qlge_exit);
-- 
1.5.0.rc4.16.g9e258

[PATCH 6/8] [RFC] qlge: Add mgmt port xface file qlge_mpi.c

[Ron Mercer]

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
---
 drivers/net/qlge/qlge_mpi.c |  228 +++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 228 insertions(+), 0 deletions(-)
 create mode 100644 drivers/net/qlge/qlge_mpi.c

diff --git a/drivers/net/qlge/qlge_mpi.c b/drivers/net/qlge/qlge_mpi.c
new file mode 100644
index 0000000..f235fc5
--- /dev/null
+++ b/drivers/net/qlge/qlge_mpi.c
@@ -0,0 +1,228 @@
+#include "qlge.h"
+
+/*
+ * Returns zero on success.
+ */
+static int ql_wait_mbx_cmd_cmplt(struct ql_adapter *qdev)
+{
+	int count = 50;
+	u32 temp;
+
+	while (count) {
+		temp = ql_read32(qdev, STS);
+		if (temp & STS_PI)
+			return 0;
+		mdelay(5);
+		count--;
+	}
+	return -ETIMEDOUT;
+}
+
+static int ql_write_mbox_reg(struct ql_adapter *qdev, u32 reg, u32 data)
+{
+	int status = 0;
+	/* wait for reg to come ready */
+	status = ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
+	if (status)
+		goto exit;
+	/* write the data to the data reg */
+	ql_write32(qdev, PROC_DATA, data);
+	/* trigger the write */
+	ql_write32(qdev, PROC_ADDR, reg);
+	/* wait for reg to come ready */
+	status = ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
+	if (status)
+		goto exit;
+exit:
+	return status;
+}
+
+static int ql_read_mbox_reg(struct ql_adapter *qdev, u32 reg, u32 *data)
+{
+	int status = 0;
+	/* wait for reg to come ready */
+	status = ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
+	if (status)
+		goto exit;
+	/* set up for reg read */
+	ql_write32(qdev, PROC_ADDR, reg | PROC_ADDR_R);
+	/* wait for reg to come ready */
+	status = ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
+	if (status)
+		goto exit;
+	/* get the data */
+	*data = ql_read32(qdev, PROC_DATA);
+exit:
+	return status;
+}
+
+static int ql_exec_mb_cmd(struct ql_adapter *qdev, struct mbox_params *mbcp)
+{
+	int i, status;
+
+	/*
+	 * Make sure there's nothing pending.
+	 * This shouldn't happen.
+	 */
+	if (ql_read32(qdev, CSR) & CSR_HRI)
+		return -EBUSY;
+
+	status = ql_sem_spinlock(qdev, SEM_PROC_REG_MASK);
+	if (status)
+		return -EBUSY;
+	/*
+	 * Fill the outbound mailboxes.
+	 */
+	for (i = 0; i < mbcp->in_count; i++) {
+		status =
+		    ql_write_mbox_reg(qdev, qdev->mailbox_in + i,
+				      mbcp->mbox_in[i]);
+		if (status)
+			goto end;
+	}
+	/*
+	 * Wake up the MPI firmware.
+	 */
+	ql_write32(qdev, CSR, CSR_CMD_SET_H2R_INT);
+end:
+	ql_sem_unlock(qdev, SEM_PROC_REG_MASK);	/* does flush too */
+	return status;
+}
+
+int ql_get_mb_sts(struct ql_adapter *qdev, struct mbox_params *mbcp)
+{
+	int i, status = 0;
+
+	status = ql_sem_spinlock(qdev, SEM_PROC_REG_MASK);
+	if (status)
+		return -EBUSY;
+	for (i = 0; i < mbcp->out_count; i++) {
+		status =
+		    ql_read_mbox_reg(qdev, qdev->mailbox_out + i,
+				     &mbcp->mbox_out[i]);
+		if (status) {
+			QPRINTK(qdev, DRV, ERR, "Failed mailbox read.\n");
+			break;
+		}
+	}
+	ql_sem_unlock(qdev, SEM_PROC_REG_MASK);	/* does flush too */
+	return status;
+}
+
+static void ql_link_up(struct ql_adapter *qdev)
+{
+	struct mbox_params mbc;
+	struct mbox_params *mbcp = &mbc;
+	mbcp->out_count = 2;
+
+	if (ql_get_mb_sts(qdev, mbcp))
+		goto exit;
+
+	qdev->link_status = mbcp->mbox_out[1];
+	QPRINTK(qdev, DRV, ERR, "Link Up.\n");
+	QPRINTK(qdev, DRV, ERR, "Link Status = 0x%.08x.\n", mbcp->mbox_out[1]);
+	if (!netif_carrier_ok(qdev->ndev)) {
+		QPRINTK(qdev, LINK, INFO, "Link is Up.\n");
+		netif_carrier_on(qdev->ndev);
+		netif_wake_queue(qdev->ndev);
+	}
+exit:
+	/* Clear the MPI firmware status. */
+	ql_write32(qdev, CSR, CSR_CMD_CLR_R2PCI_INT);
+}
+
+static void ql_link_down(struct ql_adapter *qdev)
+{
+	struct mbox_params mbc;
+	struct mbox_params *mbcp = &mbc;
+	mbcp->out_count = 3;
+
+	if (ql_get_mb_sts(qdev, mbcp)) {
+		QPRINTK(qdev, DRV, ERR, "Firmware did not initialize!\n");
+		goto exit;
+	}
+
+	if (netif_carrier_ok(qdev->ndev)) {
+		QPRINTK(qdev, LINK, INFO, "Link is Down.\n");
+		netif_carrier_off(qdev->ndev);
+		netif_stop_queue(qdev->ndev);
+	}
+	QPRINTK(qdev, DRV, ERR, "Link Down.\n");
+	QPRINTK(qdev, DRV, ERR, "Link Status = 0x%.08x.\n", mbcp->mbox_out[1]);
+exit:
+	/* Clear the MPI firmware status. */
+	ql_write32(qdev, CSR, CSR_CMD_CLR_R2PCI_INT);
+}
+
+static void ql_init_fw_done(struct ql_adapter *qdev)
+{
+	struct mbox_params mbc;
+	struct mbox_params *mbcp = &mbc;
+	mbcp->out_count = 2;
+
+	if (ql_get_mb_sts(qdev, mbcp)) {
+		QPRINTK(qdev, DRV, ERR, "Firmware did not initialize!\n");
+		goto exit;
+	}
+	QPRINTK(qdev, DRV, ERR, "Firmware initialized!\n");
+	QPRINTK(qdev, DRV, ERR, "Firmware status = 0x%.08x.\n",
+		mbcp->mbox_out[0]);
+	QPRINTK(qdev, DRV, ERR, "Firmware Revision  = 0x%.08x.\n",
+		mbcp->mbox_out[1]);
+exit:
+	/* Clear the MPI firmware status. */
+	ql_write32(qdev, CSR, CSR_CMD_CLR_R2PCI_INT);
+}
+
+void ql_mpi_work(struct work_struct *work)
+{
+	struct ql_adapter *qdev =
+	    container_of(work, struct ql_adapter, mpi_work.work);
+	struct mbox_params mbc;
+	struct mbox_params *mbcp = &mbc;
+	mbcp->out_count = 1;
+
+	while (ql_read32(qdev, STS) & STS_PI) {
+		if (ql_get_mb_sts(qdev, mbcp)) {
+			QPRINTK(qdev, DRV, ERR,
+				"Could not read MPI, resetting ASIC!\n");
+			ql_queue_asic_error(qdev);
+		}
+
+		switch (mbcp->mbox_out[0]) {
+		case AEN_LINK_UP:
+			ql_link_up(qdev);
+			break;
+		case AEN_LINK_DOWN:
+			ql_link_down(qdev);
+			break;
+		case AEN_FW_INIT_DONE:
+#ifdef PALLADIUM
+/* Palladium Workaround Start */
+		case 0:
+/* Palladium Workaround End */
+#endif
+			ql_init_fw_done(qdev);
+			break;
+		case AEN_FW_INIT_FAIL:
+			break;
+		case AEN_SYS_ERR:
+			break;
+		case MB_CMD_STS_GOOD:
+		case MB_CMD_STS_INTRMDT:
+		case MB_CMD_STS_ERR:
+		case AEN_IDC_CMPLT:
+		case AEN_IDC_REQ:
+			break;
+
+		}
+	}
+	ql_enable_completion_interrupt(qdev, 0);
+}
+
+void ql_mpi_reset_work(struct work_struct *work)
+{
+	struct ql_adapter *qdev =
+	    container_of(work, struct ql_adapter, mpi_reset_work.work);
+	printk(KERN_ERR "%s: Enter, qdev = %p..\n", __func__, qdev);
+}
-- 
1.5.0.rc4.16.g9e258

[PATCH 7/8] [RFC] qlge: Add ethtool module qlge_ethtool.c

[Ron Mercer]

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
---
 drivers/net/qlge/qlge_ethtool.c |  384 +++++++++++++++++++++++++++++++++++++++
 1 files changed, 384 insertions(+), 0 deletions(-)
 create mode 100644 drivers/net/qlge/qlge_ethtool.c

diff --git a/drivers/net/qlge/qlge_ethtool.c b/drivers/net/qlge/qlge_ethtool.c
new file mode 100644
index 0000000..f4d3880
--- /dev/null
+++ b/drivers/net/qlge/qlge_ethtool.c
@@ -0,0 +1,384 @@
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/list.h>
+#include <linux/pci.h>
+#include <linux/dma-mapping.h>
+#include <linux/pagemap.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/dmapool.h>
+#include <linux/mempool.h>
+#include <linux/spinlock.h>
+#include <linux/kthread.h>
+#include <linux/interrupt.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/in.h>
+#include <linux/ip.h>
+#include <linux/ipv6.h>
+#include <net/ipv6.h>
+#include <linux/tcp.h>
+#include <linux/udp.h>
+#include <linux/if_arp.h>
+#include <linux/if_ether.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/skbuff.h>
+#include <linux/rtnetlink.h>
+#include <linux/if_vlan.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/mm.h>
+#include <linux/vmalloc.h>
+
+#include <linux/version.h>
+
+#include "qlge.h"
+
+static int ql_update_ring_coalescing(struct ql_adapter *qdev)
+{
+	int i, err = 0;
+	struct rx_ring *rx_ring;
+	struct cqicb *cqicb;
+
+	spin_lock(&qdev->hw_lock);
+	/* Skip the default queue, and update the outbound handler
+	 * queues if they changed.
+	 */
+	cqicb = (struct cqicb *)&qdev->rx_ring[1];
+	if (le16_to_cpu(cqicb->irq_delay) != qdev->tx_coalesce_usecs ||
+	    le16_to_cpu(cqicb->pkt_delay) != qdev->tx_max_coalesced_frames) {
+		for (i = 1; i < qdev->rss_ring_first_cq_id; i++, rx_ring++) {
+			rx_ring = &qdev->rx_ring[i];
+			cqicb = (struct cqicb *)rx_ring;
+			cqicb->irq_delay = le16_to_cpu(qdev->tx_coalesce_usecs);
+			cqicb->pkt_delay =
+			    le16_to_cpu(qdev->tx_max_coalesced_frames);
+			cqicb->flags = FLAGS_LI;
+			err = ql_write_cfg(qdev, cqicb, sizeof(cqicb),
+						CFG_LCQ, rx_ring->cq_id);
+			if (err) {
+				QPRINTK(qdev, IFUP, ERR,
+					"Failed to load CQICB.\n");
+				goto exit;
+			}
+		}
+	}
+
+	/* Update the inbound (RSS) handler queues if they changed. */
+	cqicb = (struct cqicb *)&qdev->rx_ring[qdev->rss_ring_first_cq_id];
+	if (le16_to_cpu(cqicb->irq_delay) != qdev->rx_coalesce_usecs ||
+	    le16_to_cpu(cqicb->pkt_delay) != qdev->rx_max_coalesced_frames) {
+		for (i = qdev->rss_ring_first_cq_id;
+		     i <= qdev->rss_ring_first_cq_id + qdev->rss_ring_count;
+		     i++) {
+			rx_ring = &qdev->rx_ring[i];
+			cqicb = (struct cqicb *)rx_ring;
+			cqicb->irq_delay = le16_to_cpu(qdev->rx_coalesce_usecs);
+			cqicb->pkt_delay =
+			    le16_to_cpu(qdev->rx_max_coalesced_frames);
+			cqicb->flags = FLAGS_LI;
+			err = ql_write_cfg(qdev, cqicb, sizeof(cqicb),
+						CFG_LCQ, rx_ring->cq_id);
+			if (err) {
+				QPRINTK(qdev, IFUP, ERR,
+					"Failed to load CQICB.\n");
+				goto exit;
+			}
+		}
+	}
+exit:
+	spin_unlock(&qdev->hw_lock);
+	return err;
+}
+
+void ql_update_stats(struct ql_adapter *qdev)
+{
+	u32 i;
+	u64 data;
+	u64 *iter = &qdev->nic_stats.tx_pkts;
+
+	spin_lock(&qdev->stats_lock);
+	if (ql_sem_spinlock(qdev, qdev->xg_sem_mask)) {
+		printk(KERN_ERR "%s: Couldn't get xgmac sem.\n", __func__);
+		goto quit;
+	}
+	/*
+	 * Get TX statistics.
+	 */
+	for (i = 0x200; i < 0x280; i += 8) {
+		if (ql_read_xgmac_reg64(qdev, i, &data)) {
+			QPRINTK(qdev, DRV, ERR,
+				"Error reading status register 0x%.04x.\n", i);
+			goto end;
+		} else
+			*iter = data;
+		iter++;
+	}
+
+	/*
+	 * Get RX statistics.
+	 */
+	for (i = 0x300; i < 0x3d0; i += 8) {
+		if (ql_read_xgmac_reg64(qdev, i, &data)) {
+			QPRINTK(qdev, DRV, ERR,
+				"Error reading status register 0x%.04x.\n", i);
+			goto end;
+		} else
+			*iter = data;
+		iter++;
+	}
+
+end:
+	ql_sem_unlock(qdev, qdev->xg_sem_mask);
+quit:
+	spin_unlock(&qdev->stats_lock);
+
+	QL_DUMP_STAT(qdev);
+
+	return;
+}
+
+static char ql_stats_str_arr[][ETH_GSTRING_LEN] = {
+	{"tx_pkts"},
+	{"tx_bytes"},
+	{"tx_mcast_pkts"},
+	{"tx_bcast_pkts"},
+	{"tx_ucast_pkts"},
+	{"tx_ctl_pkts"},
+	{"tx_pause_pkts"},
+	{"tx_64_pkts"},
+	{"tx_65_to_127_pkts"},
+	{"tx_128_to_255_pkts"},
+	{"tx_256_511_pkts"},
+	{"tx_512_to_1023_pkts"},
+	{"tx_1024_to_1518_pkts"},
+	{"tx_1519_to_max_pkts"},
+	{"tx_undersize_pkts"},
+	{"tx_oversize_pkts"},
+	{"rx_bytes"},
+	{"rx_bytes_ok"},
+	{"rx_pkts"},
+	{"rx_pkts_ok"},
+	{"rx_bcast_pkts"},
+	{"rx_mcast_pkts"},
+	{"rx_ucast_pkts"},
+	{"rx_undersize_pkts"},
+	{"rx_oversize_pkts"},
+	{"rx_jabber_pkts"},
+	{"rx_undersize_fcerr_pkts"},
+	{"rx_drop_events"},
+	{"rx_fcerr_pkts"},
+	{"rx_align_err"},
+	{"rx_symbol_err"},
+	{"rx_mac_err"},
+	{"rx_ctl_pkts"},
+	{"rx_pause_pkts"},
+	{"rx_64_pkts"},
+	{"rx_65_to_127_pkts"},
+	{"rx_128_255_pkts"},
+	{"rx_256_511_pkts"},
+	{"rx_512_to_1023_pkts"},
+	{"rx_1024_to_1518_pkts"},
+	{"rx_1519_to_max_pkts"},
+	{"rx_len_err_pkts"},
+};
+
+static void ql_get_strings(struct net_device *dev, u32 stringset, u8 *buf)
+{
+	switch (stringset) {
+	case ETH_SS_STATS:
+		memcpy(buf, ql_stats_str_arr, sizeof(ql_stats_str_arr));
+		break;
+	}
+}
+
+static int ql_get_sset_count(struct net_device *dev, int sset)
+{
+	switch (sset) {
+	case ETH_SS_STATS:
+		return ARRAY_SIZE(ql_stats_str_arr);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
+static void
+ql_get_ethtool_stats(struct net_device *ndev,
+		     struct ethtool_stats *stats, u64 *data)
+{
+	struct ql_adapter *qdev = netdev_priv(ndev);
+	struct nic_stats *s = &qdev->nic_stats;
+
+	ql_update_stats(qdev);
+
+	*data++ = s->tx_pkts;
+	*data++ = s->tx_bytes;
+	*data++ = s->tx_mcast_pkts;
+	*data++ = s->tx_bcast_pkts;
+	*data++ = s->tx_ucast_pkts;
+	*data++ = s->tx_ctl_pkts;
+	*data++ = s->tx_pause_pkts;
+	*data++ = s->tx_64_pkt;
+	*data++ = s->tx_65_to_127_pkt;
+	*data++ = s->tx_128_to_255_pkt;
+	*data++ = s->tx_256_511_pkt;
+	*data++ = s->tx_512_to_1023_pkt;
+	*data++ = s->tx_1024_to_1518_pkt;
+	*data++ = s->tx_1519_to_max_pkt;
+	*data++ = s->tx_undersize_pkt;
+	*data++ = s->tx_oversize_pkt;
+	*data++ = s->rx_bytes;
+	*data++ = s->rx_bytes_ok;
+	*data++ = s->rx_pkts;
+	*data++ = s->rx_pkts_ok;
+	*data++ = s->rx_bcast_pkts;
+	*data++ = s->rx_mcast_pkts;
+	*data++ = s->rx_ucast_pkts;
+	*data++ = s->rx_undersize_pkts;
+	*data++ = s->rx_oversize_pkts;
+	*data++ = s->rx_jabber_pkts;
+	*data++ = s->rx_undersize_fcerr_pkts;
+	*data++ = s->rx_drop_events;
+	*data++ = s->rx_fcerr_pkts;
+	*data++ = s->rx_align_err;
+	*data++ = s->rx_symbol_err;
+	*data++ = s->rx_mac_err;
+	*data++ = s->rx_ctl_pkts;
+	*data++ = s->rx_pause_pkts;
+	*data++ = s->rx_64_pkts;
+	*data++ = s->rx_65_to_127_pkts;
+	*data++ = s->rx_128_255_pkts;
+	*data++ = s->rx_256_511_pkts;
+	*data++ = s->rx_512_to_1023_pkts;
+	*data++ = s->rx_1024_to_1518_pkts;
+	*data++ = s->rx_1519_to_max_pkts;
+	*data++ = s->rx_len_err_pkts;
+}
+
+static void ql_get_drvinfo(struct net_device *ndev,
+			   struct ethtool_drvinfo *drvinfo)
+{
+	struct ql_adapter *qdev = netdev_priv(ndev);
+	strncpy(drvinfo->driver, qlge_driver_name, 32);
+	strncpy(drvinfo->version, qlge_driver_version, 32);
+	strncpy(drvinfo->fw_version, "N/A", 32);
+	strncpy(drvinfo->bus_info, pci_name(qdev->pdev), 32);
+	drvinfo->n_stats = 0;
+	drvinfo->testinfo_len = 0;
+	drvinfo->regdump_len = 0;
+	drvinfo->eedump_len = 0;
+}
+
+static int ql_get_coalesce(struct net_device *dev, struct ethtool_coalesce *c)
+{
+	struct ql_adapter *qdev = netdev_priv(dev);
+
+	c->rx_coalesce_usecs = qdev->rx_coalesce_usecs;
+	c->tx_coalesce_usecs = qdev->tx_coalesce_usecs;
+
+	/* This chip coalesces as follows:
+	 * If a packet arrives, hold off interrupts until
+	 * cqicb->int_delay expires, but if no other packets arrive don't
+	 * wait longer than cqicb->pkt_int_delay. But ethtool doesn't use a
+	 * timer to coalesce on a frame basis.  So, we have to take ethtool's
+	 * max_coalesced_frames value and convert it to a delay in microseconds.
+	 * We do this by using a basic thoughput of 1,000,000 frames per
+	 * second @ (1024 bytes).  This means one frame per usec. So it's a
+	 * simple one to one ratio.
+	 */
+	c->rx_max_coalesced_frames = qdev->rx_max_coalesced_frames;
+	c->tx_max_coalesced_frames = qdev->tx_max_coalesced_frames;
+
+	return 0;
+}
+
+static int ql_set_coalesce(struct net_device *ndev, struct ethtool_coalesce *c)
+{
+	struct ql_adapter *qdev = netdev_priv(ndev);
+
+	/* Validate user parameters. */
+	if (c->rx_coalesce_usecs > qdev->rx_ring_size / 2)
+		return -EINVAL;
+       /* Don't wait more than 10 usec. */
+	if (c->rx_max_coalesced_frames > MAX_INTER_FRAME_WAIT)
+		return -EINVAL;
+	if (c->tx_coalesce_usecs > qdev->tx_ring_size / 2)
+		return -EINVAL;
+	if (c->tx_max_coalesced_frames > MAX_INTER_FRAME_WAIT)
+		return -EINVAL;
+
+	/* Verify a change took place before updating the hardware. */
+	if (qdev->rx_coalesce_usecs == c->rx_coalesce_usecs &&
+	    qdev->tx_coalesce_usecs == c->tx_coalesce_usecs &&
+	    qdev->rx_max_coalesced_frames == c->rx_max_coalesced_frames &&
+	    qdev->tx_max_coalesced_frames == c->tx_max_coalesced_frames)
+		return 0;
+
+	qdev->rx_coalesce_usecs = c->rx_coalesce_usecs;
+	qdev->tx_coalesce_usecs = c->tx_coalesce_usecs;
+	qdev->rx_max_coalesced_frames = c->rx_max_coalesced_frames;
+	qdev->tx_max_coalesced_frames = c->tx_max_coalesced_frames;
+
+	return ql_update_ring_coalescing(qdev);
+}
+
+static u32 ql_get_rx_csum(struct net_device *netdev)
+{
+	struct ql_adapter *qdev = netdev_priv(netdev);
+	return qdev->rx_csum;
+}
+
+static int ql_set_rx_csum(struct net_device *netdev, uint32_t data)
+{
+	struct ql_adapter *qdev = netdev_priv(netdev);
+	qdev->rx_csum = data;
+	return 0;
+}
+
+static int ql_set_tso(struct net_device *ndev, uint32_t data)
+{
+
+	if (data) {
+		ndev->features |= NETIF_F_TSO;
+		ndev->features |= NETIF_F_TSO6;
+	} else {
+		ndev->features &= ~NETIF_F_TSO;
+		ndev->features &= ~NETIF_F_TSO6;
+	}
+	return 0;
+}
+
+static u32 ql_get_msglevel(struct net_device *ndev)
+{
+	struct ql_adapter *qdev = netdev_priv(ndev);
+	return qdev->msg_enable;
+}
+
+static void ql_set_msglevel(struct net_device *ndev, u32 value)
+{
+	struct ql_adapter *qdev = netdev_priv(ndev);
+	qdev->msg_enable = value;
+}
+
+const struct ethtool_ops qlge_ethtool_ops = {
+	.get_drvinfo = ql_get_drvinfo,
+	.get_msglevel = ql_get_msglevel,
+	.set_msglevel = ql_set_msglevel,
+	.get_rx_csum = ql_get_rx_csum,
+	.set_rx_csum = ql_set_rx_csum,
+	.get_tx_csum = ethtool_op_get_tx_csum,
+	.get_sg = ethtool_op_get_sg,
+	.set_sg = ethtool_op_set_sg,
+	.get_tso = ethtool_op_get_tso,
+	.set_tso = ql_set_tso,
+	.get_coalesce = ql_get_coalesce,
+	.set_coalesce = ql_set_coalesce,
+	.get_sset_count = ql_get_sset_count,
+	.get_strings = ql_get_strings,
+	.get_ethtool_stats = ql_get_ethtool_stats,
+};
+
-- 
1.5.0.rc4.16.g9e258

[PATCH 8/8] [RFC] qlge: Add debug module qlge_dbg.c

[Ron Mercer]

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
---
 drivers/net/qlge/qlge_dbg.c |  858 +++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 858 insertions(+), 0 deletions(-)
 create mode 100644 drivers/net/qlge/qlge_dbg.c

diff --git a/drivers/net/qlge/qlge_dbg.c b/drivers/net/qlge/qlge_dbg.c
new file mode 100644
index 0000000..f0392b1
--- /dev/null
+++ b/drivers/net/qlge/qlge_dbg.c
@@ -0,0 +1,858 @@
+#include "qlge.h"
+
+#ifdef QL_REG_DUMP
+static void ql_dump_intr_states(struct ql_adapter *qdev)
+{
+	int i;
+	u32 value;
+	for (i = 0; i < qdev->intr_count; i++) {
+		ql_write32(qdev, INTR_EN, qdev->intr_context[i].intr_read_mask);
+		value = ql_read32(qdev, INTR_EN);
+		printk(KERN_ERR PFX
+		       "%s: Interrupt %d is %s.\n",
+		       qdev->ndev->name, i,
+		       (value & INTR_EN_EN ? "enabled" : "disabled"));
+	}
+}
+
+void ql_dump_xgmac_control_regs(struct ql_adapter *qdev)
+{
+	u32 data;
+	if (ql_sem_spinlock(qdev, qdev->xg_sem_mask)) {
+		printk(KERN_ERR "%s: Couldn't get xgmac sem.\n", __func__);
+		return;
+	}
+	ql_read_xgmac_reg(qdev, PAUSE_SRC_LO, &data);
+	printk(KERN_ERR PFX "%s: PAUSE_SRC_LO = 0x%.08x.\n", qdev->ndev->name,
+	       data);
+	ql_read_xgmac_reg(qdev, PAUSE_SRC_HI, &data);
+	printk(KERN_ERR PFX "%s: PAUSE_SRC_HI = 0x%.08x.\n", qdev->ndev->name,
+	       data);
+	ql_read_xgmac_reg(qdev, GLOBAL_CFG, &data);
+	printk(KERN_ERR PFX "%s: GLOBAL_CFG = 0x%.08x.\n", qdev->ndev->name,
+	       data);
+	ql_read_xgmac_reg(qdev, TX_CFG, &data);
+	printk(KERN_ERR PFX "%s: TX_CFG = 0x%.08x.\n", qdev->ndev->name, data);
+	ql_read_xgmac_reg(qdev, RX_CFG, &data);
+	printk(KERN_ERR PFX "%s: RX_CFG = 0x%.08x.\n", qdev->ndev->name, data);
+	ql_read_xgmac_reg(qdev, FLOW_CTL, &data);
+	printk(KERN_ERR PFX "%s: FLOW_CTL = 0x%.08x.\n", qdev->ndev->name,
+	       data);
+	ql_read_xgmac_reg(qdev, PAUSE_OPCODE, &data);
+	printk(KERN_ERR PFX "%s: PAUSE_OPCODE = 0x%.08x.\n", qdev->ndev->name,
+	       data);
+	ql_read_xgmac_reg(qdev, PAUSE_TIMER, &data);
+	printk(KERN_ERR PFX "%s: PAUSE_TIMER = 0x%.08x.\n", qdev->ndev->name,
+	       data);
+	ql_read_xgmac_reg(qdev, PAUSE_FRM_DEST_LO, &data);
+	printk(KERN_ERR PFX "%s: PAUSE_FRM_DEST_LO = 0x%.08x.\n",
+	       qdev->ndev->name, data);
+	ql_read_xgmac_reg(qdev, PAUSE_FRM_DEST_HI, &data);
+	printk(KERN_ERR PFX "%s: PAUSE_FRM_DEST_HI = 0x%.08x.\n",
+	       qdev->ndev->name, data);
+	ql_read_xgmac_reg(qdev, MAC_TX_PARAMS, &data);
+	printk(KERN_ERR PFX "%s: MAC_TX_PARAMS = 0x%.08x.\n", qdev->ndev->name,
+	       data);
+	ql_read_xgmac_reg(qdev, MAC_RX_PARAMS, &data);
+	printk(KERN_ERR PFX "%s: MAC_RX_PARAMS = 0x%.08x.\n", qdev->ndev->name,
+	       data);
+	ql_read_xgmac_reg(qdev, MAC_SYS_INT, &data);
+	printk(KERN_ERR PFX "%s: MAC_SYS_INT = 0x%.08x.\n", qdev->ndev->name,
+	       data);
+	ql_read_xgmac_reg(qdev, MAC_SYS_INT_MASK, &data);
+	printk(KERN_ERR PFX "%s: MAC_SYS_INT_MASK = 0x%.08x.\n",
+	       qdev->ndev->name, data);
+	ql_read_xgmac_reg(qdev, MAC_MGMT_INT, &data);
+	printk(KERN_ERR PFX "%s: MAC_MGMT_INT = 0x%.08x.\n", qdev->ndev->name,
+	       data);
+	ql_read_xgmac_reg(qdev, MAC_MGMT_IN_MASK, &data);
+	printk(KERN_ERR PFX "%s: MAC_MGMT_IN_MASK = 0x%.08x.\n",
+	       qdev->ndev->name, data);
+	ql_read_xgmac_reg(qdev, EXT_ARB_MODE, &data);
+	printk(KERN_ERR PFX "%s: EXT_ARB_MODE = 0x%.08x.\n", qdev->ndev->name,
+	       data);
+	ql_sem_unlock(qdev, qdev->xg_sem_mask);
+
+}
+
+static void ql_dump_ets_regs(struct ql_adapter *qdev)
+{
+}
+
+static void ql_dump_cam_entries(struct ql_adapter *qdev)
+{
+	int i;
+	u32 value[3];
+	for (i = 0; i < 4; i++) {
+		if (ql_get_mac_addr_reg(qdev, MAC_ADDR_TYPE_CAM_MAC, i, value)) {
+			printk(KERN_ERR PFX
+			       "%s: Failed read of mac index register.\n",
+			       __func__);
+			return;
+		} else {
+			if (value[0])
+				printk(KERN_ERR PFX
+				       "%s: CAM index %d CAM Lookup Lower = 0x%.08x:%.08x, Output = 0x%.08x.\n",
+				       qdev->ndev->name, i, value[1], value[0],
+				       value[2]);
+		}
+	}
+	for (i = 0; i < 32; i++) {
+		if (ql_get_mac_addr_reg
+		    (qdev, MAC_ADDR_TYPE_MULTI_MAC, i, value)) {
+			printk(KERN_ERR PFX
+			       "%s: Failed read of mac index register.\n",
+			       __func__);
+			return;
+		} else {
+			if (value[0])
+				printk(KERN_ERR PFX
+				       "%s: MCAST index %d CAM Lookup Lower = 0x%.08x:%.08x.\n",
+				       qdev->ndev->name, i, value[1], value[0]);
+		}
+	}
+}
+
+void ql_dump_routing_entries(struct ql_adapter *qdev)
+{
+	int i;
+	u32 value;
+	for (i = 0; i < 16; i++) {
+		value = 0;
+		if (ql_get_routing_reg(qdev, i, &value)) {
+			printk(KERN_ERR PFX
+			       "%s: Failed read of routing index register.\n",
+			       __func__);
+			return;
+		} else {
+			if (value)
+				printk(KERN_ERR PFX
+				       "%s: Routing Mask %d = 0x%.08x.\n",
+				       qdev->ndev->name, i, value);
+		}
+	}
+}
+
+void ql_dump_regs(struct ql_adapter *qdev)
+{
+	printk(KERN_ERR PFX "reg dump for function #%d.\n", qdev->func);
+	printk(KERN_ERR PFX "SYS	 			= 0x%x.\n",
+	       ql_read32(qdev, SYS));
+	printk(KERN_ERR PFX "RST_FO 			= 0x%x.\n",
+	       ql_read32(qdev, RST_FO));
+	printk(KERN_ERR PFX "FSC 				= 0x%x.\n",
+	       ql_read32(qdev, FSC));
+	printk(KERN_ERR PFX "CSR 				= 0x%x.\n",
+	       ql_read32(qdev, CSR));
+	printk(KERN_ERR PFX "ICB_RID 			= 0x%x.\n",
+	       ql_read32(qdev, ICB_RID));
+	printk(KERN_ERR PFX "ICB_L 				= 0x%x.\n",
+	       ql_read32(qdev, ICB_L));
+	printk(KERN_ERR PFX "ICB_H 				= 0x%x.\n",
+	       ql_read32(qdev, ICB_H));
+	printk(KERN_ERR PFX "CFG 				= 0x%x.\n",
+	       ql_read32(qdev, CFG));
+	printk(KERN_ERR PFX "BIOS_ADDR 			= 0x%x.\n",
+	       ql_read32(qdev, BIOS_ADDR));
+	printk(KERN_ERR PFX "STS 				= 0x%x.\n",
+	       ql_read32(qdev, STS));
+	printk(KERN_ERR PFX "INTR_EN			= 0x%x.\n",
+	       ql_read32(qdev, INTR_EN));
+	printk(KERN_ERR PFX "INTR_MASK 			= 0x%x.\n",
+	       ql_read32(qdev, INTR_MASK));
+	printk(KERN_ERR PFX "ISR1 				= 0x%x.\n",
+	       ql_read32(qdev, ISR1));
+	printk(KERN_ERR PFX "ISR2 				= 0x%x.\n",
+	       ql_read32(qdev, ISR2));
+	printk(KERN_ERR PFX "ISR3 				= 0x%x.\n",
+	       ql_read32(qdev, ISR3));
+	printk(KERN_ERR PFX "ISR4 				= 0x%x.\n",
+	       ql_read32(qdev, ISR4));
+	printk(KERN_ERR PFX "REV_ID 			= 0x%x.\n",
+	       ql_read32(qdev, REV_ID));
+	printk(KERN_ERR PFX "FRC_ECC_ERR 			= 0x%x.\n",
+	       ql_read32(qdev, FRC_ECC_ERR));
+	printk(KERN_ERR PFX "ERR_STS 			= 0x%x.\n",
+	       ql_read32(qdev, ERR_STS));
+	printk(KERN_ERR PFX "RAM_DBG_ADDR 			= 0x%x.\n",
+	       ql_read32(qdev, RAM_DBG_ADDR));
+	printk(KERN_ERR PFX "RAM_DBG_DATA 			= 0x%x.\n",
+	       ql_read32(qdev, RAM_DBG_DATA));
+	printk(KERN_ERR PFX "ECC_ERR_CNT 			= 0x%x.\n",
+	       ql_read32(qdev, ECC_ERR_CNT));
+	printk(KERN_ERR PFX "SEM 				= 0x%x.\n",
+	       ql_read32(qdev, SEM));
+	printk(KERN_ERR PFX "GPIO_1 			= 0x%x.\n",
+	       ql_read32(qdev, GPIO_1));
+	printk(KERN_ERR PFX "GPIO_2 			= 0x%x.\n",
+	       ql_read32(qdev, GPIO_2));
+	printk(KERN_ERR PFX "GPIO_3 			= 0x%x.\n",
+	       ql_read32(qdev, GPIO_3));
+	printk(KERN_ERR PFX "XGMAC_ADDR 			= 0x%x.\n",
+	       ql_read32(qdev, XGMAC_ADDR));
+	printk(KERN_ERR PFX "XGMAC_DATA 			= 0x%x.\n",
+	       ql_read32(qdev, XGMAC_DATA));
+	printk(KERN_ERR PFX "NIC_ETS 			= 0x%x.\n",
+	       ql_read32(qdev, NIC_ETS));
+	printk(KERN_ERR PFX "CNA_ETS 			= 0x%x.\n",
+	       ql_read32(qdev, CNA_ETS));
+	printk(KERN_ERR PFX "FLASH_ADDR 			= 0x%x.\n",
+	       ql_read32(qdev, FLASH_ADDR));
+	printk(KERN_ERR PFX "FLASH_DATA 			= 0x%x.\n",
+	       ql_read32(qdev, FLASH_DATA));
+	printk(KERN_ERR PFX "CQ_STOP 			= 0x%x.\n",
+	       ql_read32(qdev, CQ_STOP));
+	printk(KERN_ERR PFX "PAGE_TBL_RID 			= 0x%x.\n",
+	       ql_read32(qdev, PAGE_TBL_RID));
+	printk(KERN_ERR PFX "WQ_PAGE_TBL_LO 		= 0x%x.\n",
+	       ql_read32(qdev, WQ_PAGE_TBL_LO));
+	printk(KERN_ERR PFX "WQ_PAGE_TBL_HI 		= 0x%x.\n",
+	       ql_read32(qdev, WQ_PAGE_TBL_HI));
+	printk(KERN_ERR PFX "CQ_PAGE_TBL_LO 		= 0x%x.\n",
+	       ql_read32(qdev, CQ_PAGE_TBL_LO));
+	printk(KERN_ERR PFX "CQ_PAGE_TBL_HI 		= 0x%x.\n",
+	       ql_read32(qdev, CQ_PAGE_TBL_HI));
+	printk(KERN_ERR PFX "COS_DFLT_CQ1 			= 0x%x.\n",
+	       ql_read32(qdev, COS_DFLT_CQ1));
+	printk(KERN_ERR PFX "COS_DFLT_CQ2 			= 0x%x.\n",
+	       ql_read32(qdev, COS_DFLT_CQ2));
+	printk(KERN_ERR PFX "SPLT_HDR 			= 0x%x.\n",
+	       ql_read32(qdev, SPLT_HDR));
+	printk(KERN_ERR PFX "FC_PAUSE_THRES 		= 0x%x.\n",
+	       ql_read32(qdev, FC_PAUSE_THRES));
+	printk(KERN_ERR PFX "NIC_PAUSE_THRES 		= 0x%x.\n",
+	       ql_read32(qdev, NIC_PAUSE_THRES));
+	printk(KERN_ERR PFX "FC_ETHERTYPE 			= 0x%x.\n",
+	       ql_read32(qdev, FC_ETHERTYPE));
+	printk(KERN_ERR PFX "FC_RCV_CFG 			= 0x%x.\n",
+	       ql_read32(qdev, FC_RCV_CFG));
+	printk(KERN_ERR PFX "NIC_RCV_CFG 			= 0x%x.\n",
+	       ql_read32(qdev, NIC_RCV_CFG));
+	printk(KERN_ERR PFX "FC_COS_TAGS 			= 0x%x.\n",
+	       ql_read32(qdev, FC_COS_TAGS));
+	printk(KERN_ERR PFX "NIC_COS_TAGS 			= 0x%x.\n",
+	       ql_read32(qdev, NIC_COS_TAGS));
+	printk(KERN_ERR PFX "MGMT_RCV_CFG 			= 0x%x.\n",
+	       ql_read32(qdev, MGMT_RCV_CFG));
+	printk(KERN_ERR PFX "XG_SERDES_ADDR 		= 0x%x.\n",
+	       ql_read32(qdev, XG_SERDES_ADDR));
+	printk(KERN_ERR PFX "XG_SERDES_DATA 		= 0x%x.\n",
+	       ql_read32(qdev, XG_SERDES_DATA));
+	printk(KERN_ERR PFX "PRB_MX_ADDR 			= 0x%x.\n",
+	       ql_read32(qdev, PRB_MX_ADDR));
+	printk(KERN_ERR PFX "PRB_MX_DATA 			= 0x%x.\n",
+	       ql_read32(qdev, PRB_MX_DATA));
+	ql_dump_intr_states(qdev);
+	ql_dump_xgmac_control_regs(qdev);
+	ql_dump_ets_regs(qdev);
+	ql_dump_cam_entries(qdev);
+	ql_dump_routing_entries(qdev);
+}
+#endif
+
+#ifdef QL_STAT_DUMP
+void ql_dump_stat(struct ql_adapter *qdev)
+{
+	printk(KERN_ERR "%s: Enter.\n", __func__);
+	printk(KERN_ERR "tx_pkts = %ld\n",
+	       (unsigned long)qdev->nic_stats.tx_pkts);
+	printk(KERN_ERR "tx_bytes = %ld\n",
+	       (unsigned long)qdev->nic_stats.tx_bytes);
+	printk(KERN_ERR "tx_mcast_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_mcast_pkts);
+	printk(KERN_ERR "tx_bcast_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_bcast_pkts);
+	printk(KERN_ERR "tx_ucast_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_ucast_pkts);
+	printk(KERN_ERR "tx_ctl_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_ctl_pkts);
+	printk(KERN_ERR "tx_pause_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_pause_pkts);
+	printk(KERN_ERR "tx_64_pkt = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_64_pkt);
+	printk(KERN_ERR "tx_65_to_127_pkt = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_65_to_127_pkt);
+	printk(KERN_ERR "tx_128_to_255_pkt = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_128_to_255_pkt);
+	printk(KERN_ERR "tx_256_511_pkt = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_256_511_pkt);
+	printk(KERN_ERR "tx_512_to_1023_pkt = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_512_to_1023_pkt);
+	printk(KERN_ERR "tx_1024_to_1518_pkt = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_1024_to_1518_pkt);
+	printk(KERN_ERR "tx_1519_to_max_pkt = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_1519_to_max_pkt);
+	printk(KERN_ERR "tx_undersize_pkt = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_undersize_pkt);
+	printk(KERN_ERR "tx_oversize_pkt = %ld.\n",
+	       (unsigned long)qdev->nic_stats.tx_oversize_pkt);
+	printk(KERN_ERR "rx_bytes = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_bytes);
+	printk(KERN_ERR "rx_bytes_ok = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_bytes_ok);
+	printk(KERN_ERR "rx_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_pkts);
+	printk(KERN_ERR "rx_pkts_ok = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_pkts_ok);
+	printk(KERN_ERR "rx_bcast_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_bcast_pkts);
+	printk(KERN_ERR "rx_mcast_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_mcast_pkts);
+	printk(KERN_ERR "rx_ucast_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_ucast_pkts);
+	printk(KERN_ERR "rx_undersize_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_undersize_pkts);
+	printk(KERN_ERR "rx_oversize_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_oversize_pkts);
+	printk(KERN_ERR "rx_jabber_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_jabber_pkts);
+	printk(KERN_ERR "rx_undersize_fcerr_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_undersize_fcerr_pkts);
+	printk(KERN_ERR "rx_drop_events = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_drop_events);
+	printk(KERN_ERR "rx_fcerr_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_fcerr_pkts);
+	printk(KERN_ERR "rx_align_err = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_align_err);
+	printk(KERN_ERR "rx_symbol_err = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_symbol_err);
+	printk(KERN_ERR "rx_mac_err = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_mac_err);
+	printk(KERN_ERR "rx_ctl_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_ctl_pkts);
+	printk(KERN_ERR "rx_pause_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_pause_pkts);
+	printk(KERN_ERR "rx_64_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_64_pkts);
+	printk(KERN_ERR "rx_65_to_127_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_65_to_127_pkts);
+	printk(KERN_ERR "rx_128_255_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_128_255_pkts);
+	printk(KERN_ERR "rx_256_511_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_256_511_pkts);
+	printk(KERN_ERR "rx_512_to_1023_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_512_to_1023_pkts);
+	printk(KERN_ERR "rx_1024_to_1518_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_1024_to_1518_pkts);
+	printk(KERN_ERR "rx_1519_to_max_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_1519_to_max_pkts);
+	printk(KERN_ERR "rx_len_err_pkts = %ld.\n",
+	       (unsigned long)qdev->nic_stats.rx_len_err_pkts);
+};
+#endif
+
+#ifdef QL_DEV_DUMP
+void ql_dump_qdev(struct ql_adapter *qdev)
+{
+	int i;
+	printk(KERN_ERR PFX "qdev->flags 			= %lx.\n",
+	       qdev->flags);
+	printk(KERN_ERR PFX "qdev->vlgrp 			= %p.\n",
+	       qdev->vlgrp);
+	printk(KERN_ERR PFX "qdev->pdev 			= %p.\n",
+	       qdev->pdev);
+	printk(KERN_ERR PFX "qdev->ndev 			= %p.\n",
+	       qdev->ndev);
+	printk(KERN_ERR PFX "qdev->chip_rev_id 		= %d.\n",
+	       qdev->chip_rev_id);
+	printk(KERN_ERR PFX "qdev->reg_base 		= %p.\n",
+	       qdev->reg_base);
+	printk(KERN_ERR PFX "qdev->doorbell_area 	= %p.\n",
+	       qdev->doorbell_area);
+	printk(KERN_ERR PFX "qdev->doorbell_area_size 	= %d.\n",
+	       qdev->doorbell_area_size);
+	printk(KERN_ERR PFX "msg_enable 		= %x.\n",
+	       qdev->msg_enable);
+	printk(KERN_ERR PFX "qdev->rx_ring_shadow_reg_area	= %p.\n",
+	       qdev->rx_ring_shadow_reg_area);
+	printk(KERN_ERR PFX "qdev->rx_ring_shadow_reg_dma 	= %p.\n",
+	       (void *)qdev->rx_ring_shadow_reg_dma);
+	printk(KERN_ERR PFX "qdev->tx_ring_shadow_reg_area	= %p.\n",
+	       qdev->tx_ring_shadow_reg_area);
+	printk(KERN_ERR PFX "qdev->tx_ring_shadow_reg_dma	= %p.\n",
+	       (void *)qdev->tx_ring_shadow_reg_dma);
+	printk(KERN_ERR PFX "qdev->intr_count 		= %d.\n",
+	       qdev->intr_count);
+	if (qdev->msi_x_entry)
+		for (i = 0; i < qdev->intr_count; i++) {
+			printk(KERN_ERR PFX
+			       "msi_x_entry.[%d]vector	= %d.\n", i,
+			       qdev->msi_x_entry[i].vector);
+			printk(KERN_ERR PFX
+			       "msi_x_entry.[%d]entry	= %d.\n", i,
+			       qdev->msi_x_entry[i].entry);
+		}
+	for (i = 0; i < qdev->intr_count; i++) {
+		printk(KERN_ERR PFX
+		       "intr_context[%d].qdev		= %p.\n", i,
+		       qdev->intr_context[i].qdev);
+		printk(KERN_ERR PFX
+		       "intr_context[%d].intr		= %d.\n", i,
+		       qdev->intr_context[i].intr);
+		printk(KERN_ERR PFX
+		       "intr_context[%d].hooked		= %d.\n", i,
+		       qdev->intr_context[i].hooked);
+		printk(KERN_ERR PFX
+		       "intr_context[%d].intr_en_mask	= 0x%08x.\n", i,
+		       qdev->intr_context[i].intr_en_mask);
+		printk(KERN_ERR PFX
+		       "intr_context[%d].intr_dis_mask	= 0x%08x.\n", i,
+		       qdev->intr_context[i].intr_dis_mask);
+		printk(KERN_ERR PFX
+		       "intr_context[%d].intr_read_mask	= 0x%08x.\n", i,
+		       qdev->intr_context[i].intr_read_mask);
+	}
+	printk(KERN_ERR PFX "qdev->tx_ring_count = %d.\n", qdev->tx_ring_count);
+	printk(KERN_ERR PFX "qdev->rx_ring_count = %d.\n", qdev->rx_ring_count);
+	printk(KERN_ERR PFX "qdev->ring_mem_size = %d.\n", qdev->ring_mem_size);
+	printk(KERN_ERR PFX "qdev->ring_mem 	= %p.\n", qdev->ring_mem);
+	printk(KERN_ERR PFX "qdev->intr_count 	= %d.\n", qdev->intr_count);
+	printk(KERN_ERR PFX "qdev->tx_ring		= %p.\n",
+	       qdev->tx_ring);
+	printk(KERN_ERR PFX "qdev->rss_ring_first_cq_id 	= %d.\n",
+	       qdev->rss_ring_first_cq_id);
+	printk(KERN_ERR PFX "qdev->rss_ring_count 	= %d.\n",
+	       qdev->rss_ring_count);
+	printk(KERN_ERR PFX "qdev->rx_ring	= %p.\n", qdev->rx_ring);
+	printk(KERN_ERR PFX "qdev->default_rx_queue	= %d.\n",
+	       qdev->default_rx_queue);
+	printk(KERN_ERR PFX "qdev->xg_sem_mask		= 0x%08x.\n",
+	       qdev->xg_sem_mask);
+	printk(KERN_ERR PFX "qdev->port_link_up		= 0x%08x.\n",
+	       qdev->port_link_up);
+	printk(KERN_ERR PFX "qdev->port_init		= 0x%08x.\n",
+	       qdev->port_init);
+
+}
+#endif
+
+#ifdef QL_CB_DUMP
+void ql_dump_wqicb(struct wqicb *wqicb)
+{
+	printk(KERN_ERR PFX "Dumping wqicb stuff...\n");
+	printk(KERN_ERR PFX "wqicb->len = 0x%x.\n", le16_to_cpu(wqicb->len));
+	printk(KERN_ERR PFX "wqicb->flags = %x.\n", le16_to_cpu(wqicb->flags));
+	printk(KERN_ERR PFX "wqicb->cq_id_rss = %d.\n",
+	       le16_to_cpu(wqicb->cq_id_rss));
+	printk(KERN_ERR PFX "wqicb->rid = 0x%x.\n", le16_to_cpu(wqicb->rid));
+	printk(KERN_ERR PFX "wqicb->wq_addr_lo = 0x%.08x.\n",
+	       le32_to_cpu(wqicb->addr_lo));
+	printk(KERN_ERR PFX "wqicb->wq_addr_hi = 0x%.08x.\n",
+	       le32_to_cpu(wqicb->addr_hi));
+	printk(KERN_ERR PFX "wqicb->wq_cnsmr_idx_addr_lo = 0x%.08x.\n",
+	       le32_to_cpu(wqicb->cnsmr_idx_addr_lo));
+	printk(KERN_ERR PFX "wqicb->wq_cnsmr_idx_addr_hi = 0x%.08x.\n",
+	       le32_to_cpu(wqicb->cnsmr_idx_addr_hi));
+}
+
+void ql_dump_tx_ring(struct tx_ring *tx_ring)
+{
+	if (tx_ring == NULL)
+		return;
+	printk(KERN_ERR PFX
+	       "===================== Dumping tx_ring %d ===============.\n",
+	       tx_ring->wq_id);
+	printk(KERN_ERR PFX "tx_ring->base = %p.\n", tx_ring->wq_base);
+	printk(KERN_ERR PFX "tx_ring->base_dma = 0x%llx.\n",
+	       (u64) tx_ring->wq_base_dma);
+	printk(KERN_ERR PFX "tx_ring->cnsmr_idx_sh_reg = %p.\n",
+	       tx_ring->cnsmr_idx_sh_reg);
+	printk(KERN_ERR PFX "tx_ring->cnsmr_idx_sh_reg_dma = 0x%llx.\n",
+	       (u64) tx_ring->cnsmr_idx_sh_reg_dma);
+	printk(KERN_ERR PFX "tx_ring->size = %d.\n", tx_ring->wq_size);
+	printk(KERN_ERR PFX "tx_ring->len = %d.\n", tx_ring->wq_len);
+	printk(KERN_ERR PFX "tx_ring->prod_idx_db_reg = %p.\n",
+	       tx_ring->prod_idx_db_reg);
+	printk(KERN_ERR PFX "tx_ring->valid_db_reg = %p.\n",
+	       tx_ring->valid_db_reg);
+	printk(KERN_ERR PFX "tx_ring->prod_idx = %d.\n", tx_ring->prod_idx);
+	printk(KERN_ERR PFX "tx_ring->cq_id = %d.\n", tx_ring->cq_id);
+	printk(KERN_ERR PFX "tx_ring->wq_id = %d.\n", tx_ring->wq_id);
+	printk(KERN_ERR PFX "tx_ring->q = %p.\n", tx_ring->q);
+	printk(KERN_ERR PFX "tx_ring->tx_count = %d.\n",
+	       atomic_read(&tx_ring->tx_count));
+}
+
+void ql_dump_ricb(struct ricb *ricb)
+{
+	int i;
+	printk(KERN_ERR PFX
+	       "===================== Dumping ricb ===============.\n");
+	printk(KERN_ERR PFX "Dumping ricb stuff...\n");
+
+	printk(KERN_ERR PFX "ricb->base_cq = %d.\n", ricb->base_cq & 0x1f);
+	printk(KERN_ERR PFX "ricb->flags = %s%s%s%s%s%s%s%s%s.\n",
+	       ricb->base_cq & RSS_L4K ? "RSS_L4K " : "",
+	       ricb->flags & RSS_L6K ? "RSS_L6K " : "",
+	       ricb->flags & RSS_LI ? "RSS_LI " : "",
+	       ricb->flags & RSS_LB ? "RSS_LB " : "",
+	       ricb->flags & RSS_LM ? "RSS_LM " : "",
+	       ricb->flags & RSS_RI4 ? "RSS_RI4 " : "",
+	       ricb->flags & RSS_RT4 ? "RSS_RT4 " : "",
+	       ricb->flags & RSS_RI6 ? "RSS_RI6 " : "",
+	       ricb->flags & RSS_RT6 ? "RSS_RT6 " : "");
+	printk(KERN_ERR PFX "ricb->mask = 0x%.04x.\n", le16_to_cpu(ricb->mask));
+	for (i = 0; i < 16; i++)
+		printk(KERN_ERR PFX "ricb->hash_cq_id[%d] = 0x%.08x.\n", i,
+		       le32_to_cpu(ricb->hash_cq_id[i]));
+	for (i = 0; i < 10; i++)
+		printk(KERN_ERR PFX "ricb->ipv6_hash_key[%d] = 0x%.08x.\n", i,
+		       le32_to_cpu(ricb->ipv6_hash_key[i]));
+	for (i = 0; i < 4; i++)
+		printk(KERN_ERR PFX "ricb->ipv4_hash_key[%d] = 0x%.08x.\n", i,
+		       le32_to_cpu(ricb->ipv4_hash_key[i]));
+}
+
+void ql_dump_cqicb(struct cqicb *cqicb)
+{
+	printk(KERN_ERR PFX "Dumping cqicb stuff...\n");
+
+	printk(KERN_ERR PFX "cqicb->msix_vect = %d.\n", cqicb->msix_vect);
+	printk(KERN_ERR PFX "cqicb->flags = %x.\n", cqicb->flags);
+	printk(KERN_ERR PFX "cqicb->len = %d.\n", le16_to_cpu(cqicb->len));
+	printk(KERN_ERR PFX "cqicb->addr_lo = %x.\n",
+	       le32_to_cpu(cqicb->addr_lo));
+	printk(KERN_ERR PFX "cqicb->addr_hi = %x.\n",
+	       le32_to_cpu(cqicb->addr_hi));
+	printk(KERN_ERR PFX "cqicb->prod_idx_addr_lo = %x.\n",
+	       le32_to_cpu(cqicb->prod_idx_addr_lo));
+	printk(KERN_ERR PFX "cqicb->prod_idx_addr_hi = %x.\n",
+	       le32_to_cpu(cqicb->prod_idx_addr_hi));
+	printk(KERN_ERR PFX "cqicb->pkt_delay = 0x%.04x.\n",
+	       le16_to_cpu(cqicb->pkt_delay));
+	printk(KERN_ERR PFX "cqicb->irq_delay = 0x%.04x.\n",
+	       le16_to_cpu(cqicb->irq_delay));
+	printk(KERN_ERR PFX "cqicb->lbq_addr_lo = %x.\n",
+	       le32_to_cpu(cqicb->lbq_addr_lo));
+	printk(KERN_ERR PFX "cqicb->lbq_addr_hi = %x.\n",
+	       le32_to_cpu(cqicb->lbq_addr_hi));
+	printk(KERN_ERR PFX "cqicb->lbq_buf_size = 0x%.04x.\n",
+	       le16_to_cpu(cqicb->lbq_buf_size));
+	printk(KERN_ERR PFX "cqicb->lbq_len = 0x%.04x.\n",
+	       le16_to_cpu(cqicb->lbq_len));
+	printk(KERN_ERR PFX "cqicb->sbq_addr_lo = %x.\n",
+	       le32_to_cpu(cqicb->sbq_addr_lo));
+	printk(KERN_ERR PFX "cqicb->sbq_addr_hi = %x.\n",
+	       le32_to_cpu(cqicb->sbq_addr_hi));
+	printk(KERN_ERR PFX "cqicb->sbq_buf_size = 0x%.04x.\n",
+	       le16_to_cpu(cqicb->sbq_buf_size));
+	printk(KERN_ERR PFX "cqicb->sbq_len = 0x%.04x.\n",
+	       le16_to_cpu(cqicb->sbq_len));
+}
+
+void ql_dump_rx_ring(struct rx_ring *rx_ring)
+{
+	if (rx_ring == NULL)
+		return;
+	printk(KERN_ERR PFX
+	       "===================== Dumping rx_ring %d ===============.\n",
+	       rx_ring->cq_id);
+	printk(KERN_ERR PFX "Dumping rx_ring %d, type = %s%s%s.\n",
+	       rx_ring->cq_id, rx_ring->type == DEFAULT_Q ? "DEFAULT" : "",
+	       rx_ring->type == TX_Q ? "OUTBOUND COMPLETIONS" : "",
+	       rx_ring->type == RX_Q ? "INBOUND_COMPLETIONS" : "");
+	printk(KERN_ERR PFX "rx_ring->cqicb = %p.\n", &rx_ring->cqicb);
+	printk(KERN_ERR PFX "rx_ring->cq_base = %p.\n", rx_ring->cq_base);
+	printk(KERN_ERR PFX "rx_ring->cq_base_dma = %llx.\n",
+	       (u64) rx_ring->cq_base_dma);
+	printk(KERN_ERR PFX "rx_ring->cq_size = %d.\n", rx_ring->cq_size);
+	printk(KERN_ERR PFX "rx_ring->cq_len = %d.\n", rx_ring->cq_len);
+	printk(KERN_ERR PFX
+	       "rx_ring->prod_idx_sh_reg, addr = %p, value = %d.\n",
+	       rx_ring->prod_idx_sh_reg,
+	       rx_ring->prod_idx_sh_reg ? *(rx_ring->prod_idx_sh_reg) : 0);
+	printk(KERN_ERR PFX "rx_ring->prod_idx_sh_reg_dma = %llx.\n",
+	       (u64) rx_ring->prod_idx_sh_reg_dma);
+	printk(KERN_ERR PFX "rx_ring->cnsmr_idx_db_reg = %p.\n",
+	       rx_ring->cnsmr_idx_db_reg);
+	printk(KERN_ERR PFX "rx_ring->cnsmr_idx = %d.\n", rx_ring->cnsmr_idx);
+	printk(KERN_ERR PFX "rx_ring->curr_entry = %p.\n", rx_ring->curr_entry);
+	printk(KERN_ERR PFX "rx_ring->valid_db_reg = %p.\n",
+	       rx_ring->valid_db_reg);
+
+	printk(KERN_ERR PFX "rx_ring->lbq_base = %p.\n", rx_ring->lbq_base);
+	printk(KERN_ERR PFX "rx_ring->lbq_base_dma = %llx.\n",
+	       (u64) rx_ring->lbq_base_dma);
+	printk(KERN_ERR PFX "rx_ring->lbq_base_indirect = %p.\n",
+	       rx_ring->lbq_base_indirect);
+	printk(KERN_ERR PFX "rx_ring->lbq_base_indirect_dma = %llx.\n",
+	       (u64) rx_ring->lbq_base_indirect_dma);
+	printk(KERN_ERR PFX "rx_ring->lbq = %p.\n", rx_ring->lbq);
+	printk(KERN_ERR PFX "rx_ring->lbq_len = %d.\n", rx_ring->lbq_len);
+	printk(KERN_ERR PFX "rx_ring->lbq_size = %d.\n", rx_ring->lbq_size);
+	printk(KERN_ERR PFX "rx_ring->lbq_prod_idx_db_reg = %p.\n",
+	       rx_ring->lbq_prod_idx_db_reg);
+	printk(KERN_ERR PFX "rx_ring->lbq_prod_idx = %d.\n",
+	       rx_ring->lbq_prod_idx);
+	printk(KERN_ERR PFX "rx_ring->lbq_curr_idx = %d.\n",
+	       rx_ring->lbq_curr_idx);
+	printk(KERN_ERR PFX "rx_ring->lbq_clean_idx = %d.\n",
+	       rx_ring->lbq_clean_idx);
+	printk(KERN_ERR PFX "rx_ring->lbq_free_cnt = %d.\n",
+	       rx_ring->lbq_free_cnt);
+	printk(KERN_ERR PFX "rx_ring->lbq_buf_size = %d.\n",
+	       rx_ring->lbq_buf_size);
+
+	printk(KERN_ERR PFX "rx_ring->sbq_base = %p.\n", rx_ring->sbq_base);
+	printk(KERN_ERR PFX "rx_ring->sbq_base_dma = %llx.\n",
+	       (u64) rx_ring->sbq_base_dma);
+	printk(KERN_ERR PFX "rx_ring->sbq_base_indirect = %p.\n",
+	       rx_ring->sbq_base_indirect);
+	printk(KERN_ERR PFX "rx_ring->sbq_base_indirect_dma = %llx.\n",
+	       (u64) rx_ring->sbq_base_indirect_dma);
+	printk(KERN_ERR PFX "rx_ring->sbq = %p.\n", rx_ring->sbq);
+	printk(KERN_ERR PFX "rx_ring->sbq_len = %d.\n", rx_ring->sbq_len);
+	printk(KERN_ERR PFX "rx_ring->sbq_size = %d.\n", rx_ring->sbq_size);
+	printk(KERN_ERR PFX "rx_ring->sbq_prod_idx_db_reg addr = %p.\n",
+	       rx_ring->sbq_prod_idx_db_reg);
+	printk(KERN_ERR PFX "rx_ring->sbq_prod_idx = %d.\n",
+	       rx_ring->sbq_prod_idx);
+	printk(KERN_ERR PFX "rx_ring->sbq_curr_idx = %d.\n",
+	       rx_ring->sbq_curr_idx);
+	printk(KERN_ERR PFX "rx_ring->sbq_clean_idx = %d.\n",
+	       rx_ring->sbq_clean_idx);
+	printk(KERN_ERR PFX "rx_ring->sbq_free_cnt = %d.\n",
+	       rx_ring->sbq_free_cnt);
+	printk(KERN_ERR PFX "rx_ring->sbq_buf_size = %d.\n",
+	       rx_ring->sbq_buf_size);
+	printk(KERN_ERR PFX "rx_ring->cq_id = %d.\n", rx_ring->cq_id);
+	printk(KERN_ERR PFX "rx_ring->irq = %d.\n", rx_ring->irq);
+	printk(KERN_ERR PFX "rx_ring->cpu = %d.\n", rx_ring->cpu);
+	printk(KERN_ERR PFX "rx_ring->qdev = %p.\n", rx_ring->qdev);
+}
+
+void ql_dump_hw_cb(struct ql_adapter *qdev, int size, u32 bit, u16 q_id)
+{
+	void *ptr;
+
+	printk(KERN_ERR PFX "%s: Enter.\n", __func__);
+
+	ptr = kmalloc(size, GFP_ATOMIC);
+	if (ptr == NULL) {
+		printk(KERN_ERR PFX "%s: Couldn't allocate a buffer.\n",
+		       __func__);
+		return;
+	}
+
+	if (ql_write_cfg(qdev, ptr, size, bit, q_id)) {
+		printk(KERN_ERR "%s: Failed to upload control block!\n",
+		       __func__);
+		goto fail_it;
+	}
+	switch (bit) {
+	case CFG_DRQ:
+		ql_dump_wqicb((struct wqicb *)ptr);
+		break;
+	case CFG_DCQ:
+		ql_dump_cqicb((struct cqicb *)ptr);
+		break;
+	case CFG_DR:
+		ql_dump_ricb((struct ricb *)ptr);
+		break;
+	default:
+		printk(KERN_ERR PFX "%s: Invalid bit value = %x.\n",
+		       __func__, bit);
+		break;
+	}
+fail_it:
+	kfree(ptr);
+}
+#endif
+
+#ifdef QL_OB_DUMP
+void ql_dump_tx_desc(struct tx_buf_desc *tbd)
+{
+	printk(KERN_ERR PFX "tbd->addr  = 0x%llx\n",
+	       le64_to_cpu((u64) tbd->addr));
+	printk(KERN_ERR PFX "tbd->len   = %d\n",
+	       le32_to_cpu(tbd->len & TX_DESC_LEN_MASK));
+	printk(KERN_ERR PFX "tbd->flags = %s %s\n",
+	       tbd->len & TX_DESC_C ? "C" : ".",
+	       tbd->len & TX_DESC_E ? "E" : ".");
+	tbd++;
+	printk(KERN_ERR PFX "tbd->addr  = 0x%llx\n",
+	       le64_to_cpu((u64) tbd->addr));
+	printk(KERN_ERR PFX "tbd->len   = %d\n",
+	       le32_to_cpu(tbd->len & TX_DESC_LEN_MASK));
+	printk(KERN_ERR PFX "tbd->flags = %s %s\n",
+	       tbd->len & TX_DESC_C ? "C" : ".",
+	       tbd->len & TX_DESC_E ? "E" : ".");
+	tbd++;
+	printk(KERN_ERR PFX "tbd->addr  = 0x%llx\n",
+	       le64_to_cpu((u64) tbd->addr));
+	printk(KERN_ERR PFX "tbd->len   = %d\n",
+	       le32_to_cpu(tbd->len & TX_DESC_LEN_MASK));
+	printk(KERN_ERR PFX "tbd->flags = %s %s\n",
+	       tbd->len & TX_DESC_C ? "C" : ".",
+	       tbd->len & TX_DESC_E ? "E" : ".");
+
+}
+
+void ql_dump_ob_mac_iocb(struct ob_mac_iocb_req *ob_mac_iocb)
+{
+	struct ob_mac_tso_iocb_req *ob_mac_tso_iocb =
+	    (struct ob_mac_tso_iocb_req *)ob_mac_iocb;
+	struct tx_buf_desc *tbd;
+	u16 frame_len;
+
+	printk(KERN_ERR PFX "%s\n", __func__);
+	printk(KERN_ERR PFX "opcode         = %s\n",
+	       (ob_mac_iocb->opcode == OPCODE_OB_MAC_IOCB) ? "MAC" : "TSO");
+	printk(KERN_ERR PFX "flags1          = %s %s %s %s %s\n",
+	       ob_mac_tso_iocb->flags1 & OB_MAC_TSO_IOCB_OI ? "OI" : "",
+	       ob_mac_tso_iocb->flags1 & OB_MAC_TSO_IOCB_I ? "I" : "",
+	       ob_mac_tso_iocb->flags1 & OB_MAC_TSO_IOCB_D ? "D" : "",
+	       ob_mac_tso_iocb->flags1 & OB_MAC_TSO_IOCB_IP4 ? "IP4" : "",
+	       ob_mac_tso_iocb->flags1 & OB_MAC_TSO_IOCB_IP6 ? "IP6" : "");
+	printk(KERN_ERR PFX "flags2          = %s %s %s\n",
+	       ob_mac_tso_iocb->flags2 & OB_MAC_TSO_IOCB_LSO ? "LSO" : "",
+	       ob_mac_tso_iocb->flags2 & OB_MAC_TSO_IOCB_UC ? "UC" : "",
+	       ob_mac_tso_iocb->flags2 & OB_MAC_TSO_IOCB_TC ? "TC" : "");
+	printk(KERN_ERR PFX "flags3          = %s %s %s \n",
+	       ob_mac_tso_iocb->flags3 & OB_MAC_TSO_IOCB_IC ? "IC" : "",
+	       ob_mac_tso_iocb->flags3 & OB_MAC_TSO_IOCB_DFP ? "DFP" : "",
+	       ob_mac_tso_iocb->flags3 & OB_MAC_TSO_IOCB_V ? "V" : "");
+	printk(KERN_ERR PFX "tid = %x\n", ob_mac_iocb->tid);
+	printk(KERN_ERR PFX "txq_idx = %d\n", ob_mac_iocb->txq_idx);
+	printk(KERN_ERR PFX "vlan_tci      = %x\n", ob_mac_tso_iocb->vlan_tci);
+	if (ob_mac_iocb->opcode == OPCODE_OB_MAC_TSO_IOCB) {
+		printk(KERN_ERR PFX "frame_len      = %d\n",
+		       le32_to_cpu(ob_mac_tso_iocb->frame_len));
+		printk(KERN_ERR PFX "mss      = %d\n",
+		       le16_to_cpu(ob_mac_tso_iocb->mss));
+		printk(KERN_ERR PFX "prot_hdr_len   = %d\n",
+		       le16_to_cpu(ob_mac_tso_iocb->total_hdrs_len));
+		printk(KERN_ERR PFX "hdr_offset     = 0x%.04x\n",
+		       le16_to_cpu(ob_mac_tso_iocb->net_trans_offset));
+		frame_len = le32_to_cpu(ob_mac_tso_iocb->frame_len);
+	} else {
+		printk(KERN_ERR PFX "frame_len      = %d\n",
+		       le16_to_cpu(ob_mac_iocb->frame_len));
+		frame_len = le16_to_cpu(ob_mac_iocb->frame_len);
+	}
+	tbd = &ob_mac_iocb->tbd[0];
+	ql_dump_tx_desc(tbd);
+}
+
+void ql_dump_ob_mac_rsp(struct ob_mac_iocb_rsp *ob_mac_rsp)
+{
+	printk(KERN_ERR PFX "%s\n", __func__);
+	printk(KERN_ERR PFX "opcode         = %d\n", ob_mac_rsp->opcode);
+	printk(KERN_ERR PFX "flags          = %s %s %s %s %s %s %s\n",
+	       ob_mac_rsp->flags1 & OB_MAC_IOCB_RSP_OI ? "OI" : ".",
+	       ob_mac_rsp->flags1 & OB_MAC_IOCB_RSP_I ? "I" : ".",
+	       ob_mac_rsp->flags1 & OB_MAC_IOCB_RSP_E ? "E" : ".",
+	       ob_mac_rsp->flags1 & OB_MAC_IOCB_RSP_S ? "S" : ".",
+	       ob_mac_rsp->flags1 & OB_MAC_IOCB_RSP_L ? "L" : ".",
+	       ob_mac_rsp->flags1 & OB_MAC_IOCB_RSP_P ? "P" : ".",
+	       ob_mac_rsp->flags2 & OB_MAC_IOCB_RSP_B ? "B" : ".");
+	printk(KERN_ERR PFX "tid = %x\n", ob_mac_rsp->tid);
+}
+#endif
+
+#ifdef QL_IB_DUMP
+void ql_dump_ib_mac_rsp(struct ib_mac_iocb_rsp *ib_mac_rsp)
+{
+	printk(KERN_ERR PFX "%s\n", __func__);
+	printk(KERN_ERR PFX "opcode         = 0x%x\n", ib_mac_rsp->opcode);
+	printk(KERN_ERR PFX "flags1 = %s%s%s%s%s%s\n",
+	       ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_OI ? "OI " : "",
+	       ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_I ? "I " : "",
+	       ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_TE ? "TE " : "",
+	       ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_NU ? "NU " : "",
+	       ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_IE ? "IE " : "",
+	       ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_B ? "B " : "");
+
+	if (ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_M_MASK)
+		printk(KERN_ERR PFX "%s%s%s Multicast.\n",
+		       (ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_M_MASK) ==
+		       IB_MAC_IOCB_RSP_M_HASH ? "Hash" : "",
+		       (ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_M_MASK) ==
+		       IB_MAC_IOCB_RSP_M_REG ? "Registered" : "",
+		       (ib_mac_rsp->flags1 & IB_MAC_IOCB_RSP_M_MASK) ==
+		       IB_MAC_IOCB_RSP_M_PROM ? "Promiscuous" : "");
+
+	printk(KERN_ERR PFX "flags2 = %s%s%s%s%s\n",
+	       (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_P) ? "P " : "",
+	       (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_V) ? "V " : "",
+	       (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_U) ? "U " : "",
+	       (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_T) ? "T " : "",
+	       (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_FO) ? "FO " : "");
+
+	if (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_ERR_MASK)
+		printk(KERN_ERR PFX "%s%s%s%s%s error.\n",
+		       (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_ERR_MASK) ==
+		       IB_MAC_IOCB_RSP_ERR_OVERSIZE ? "oversize" : "",
+		       (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_ERR_MASK) ==
+		       IB_MAC_IOCB_RSP_ERR_UNDERSIZE ? "undersize" : "",
+		       (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_ERR_MASK) ==
+		       IB_MAC_IOCB_RSP_ERR_PREAMBLE ? "preamble" : "",
+		       (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_ERR_MASK) ==
+		       IB_MAC_IOCB_RSP_ERR_FRAME_LEN ? "frame length" : "",
+		       (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_ERR_MASK) ==
+		       IB_MAC_IOCB_RSP_ERR_CRC ? "CRC" : "");
+
+	printk(KERN_ERR PFX "flags3 = %s%s.\n",
+	       ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_DS ? "DS " : "",
+	       ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_DL ? "DL " : "");
+
+	if (ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_RSS_MASK)
+		printk(KERN_ERR PFX "RSS flags = %s%s%s%s.\n",
+		       ((ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_RSS_MASK) ==
+			IB_MAC_IOCB_RSP_M_IPV4) ? "IPv4 RSS" : "",
+		       ((ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_RSS_MASK) ==
+			IB_MAC_IOCB_RSP_M_IPV6) ? "IPv6 RSS " : "",
+		       ((ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_RSS_MASK) ==
+			IB_MAC_IOCB_RSP_M_TCP_V4) ? "TCP/IPv4 RSS" : "",
+		       ((ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_RSS_MASK) ==
+			IB_MAC_IOCB_RSP_M_TCP_V6) ? "TCP/IPv6 RSS" : "");
+
+	printk(KERN_ERR PFX "data_len	= %d\n",
+	       le32_to_cpu(ib_mac_rsp->data_len));
+	printk(KERN_ERR PFX "data_addr_hi    = 0x%x\n",
+	       le32_to_cpu(ib_mac_rsp->data_addr_hi));
+	printk(KERN_ERR PFX "data_addr_lo    = 0x%x\n",
+	       le32_to_cpu(ib_mac_rsp->data_addr_lo));
+	if (ib_mac_rsp->flags3 & IB_MAC_IOCB_RSP_RSS_MASK)
+		printk(KERN_ERR PFX "rss    = %x\n",
+		       le32_to_cpu(ib_mac_rsp->rss));
+	if (ib_mac_rsp->flags2 & IB_MAC_IOCB_RSP_V)
+		printk(KERN_ERR PFX "vlan_id    = %x\n",
+		       le16_to_cpu(ib_mac_rsp->vlan_id));
+
+	printk(KERN_ERR PFX "flags4 = %s%s%s.\n",
+	       le32_to_cpu(ib_mac_rsp->
+			   flags4) & IB_MAC_IOCB_RSP_HV ? "HV " : "",
+	       le32_to_cpu(ib_mac_rsp->
+			   flags4) & IB_MAC_IOCB_RSP_HS ? "HS " : "",
+	       le32_to_cpu(ib_mac_rsp->
+			   flags4) & IB_MAC_IOCB_RSP_HL ? "HL " : "");
+
+	if (le32_to_cpu(ib_mac_rsp->flags4) & IB_MAC_IOCB_RSP_HV) {
+		printk(KERN_ERR PFX "hdr length	= %d.\n",
+		       le32_to_cpu(ib_mac_rsp->hdr_len));
+		printk(KERN_ERR PFX "hdr addr_hi    = 0x%x.\n",
+		       le32_to_cpu(ib_mac_rsp->hdr_addr_hi));
+		printk(KERN_ERR PFX "hdr addr_lo    = 0x%x.\n",
+		       le32_to_cpu(ib_mac_rsp->hdr_addr_lo));
+	}
+}
+#endif
+
+#ifdef QL_ALL_DUMP
+void ql_dump_all(struct ql_adapter *qdev)
+{
+	int i;
+
+	QL_DUMP_REGS(qdev);
+	QL_DUMP_QDEV(qdev);
+	for (i = 0; i < qdev->tx_ring_count; i++) {
+		QL_DUMP_TX_RING(&qdev->tx_ring[i]);
+		QL_DUMP_WQICB((struct wqicb *)&qdev->tx_ring[i]);
+	}
+	for (i = 0; i < qdev->rx_ring_count; i++) {
+		QL_DUMP_RX_RING(&qdev->rx_ring[i]);
+		QL_DUMP_CQICB((struct cqicb *)&qdev->rx_ring[i]);
+	}
+}
+#endif
-- 
1.5.0.rc4.16.g9e258

Re: [PATCH 6/8] [RFC] qlge: Add mgmt port xface file qlge_mpi.c

[Franco Fichtner]

Ron Mercer wrote:
> Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
> ---
>  drivers/net/qlge/qlge_mpi.c |  228 +++++++++++++++++++++++++++++++++++++++++++
>  1 files changed, 228 insertions(+), 0 deletions(-)
>  create mode 100644 drivers/net/qlge/qlge_mpi.c
> 
> diff --git a/drivers/net/qlge/qlge_mpi.c b/drivers/net/qlge/qlge_mpi.c
> new file mode 100644
> index 0000000..f235fc5
> --- /dev/null
> +++ b/drivers/net/qlge/qlge_mpi.c
> @@ -0,0 +1,228 @@
> +#include "qlge.h"
> +
> +/*
> + * Returns zero on success.
> + */
> +static int ql_wait_mbx_cmd_cmplt(struct ql_adapter *qdev)
> +{
> +	int count = 50;
> +	u32 temp;
> +
> +	while (count) {
> +		temp = ql_read32(qdev, STS);
> +		if (temp & STS_PI)
> +			return 0;
> +		mdelay(5);

Do you really want to delay execution for 250ms in worst case (timeout)
scenarios? A msleep() would be more graceful.

> +		count--;
> +	}
> +	return -ETIMEDOUT;
> +}
> +
> +static int ql_write_mbox_reg(struct ql_adapter *qdev, u32 reg, u32 data)
> +{
> +	int status = 0;
> +	/* wait for reg to come ready */
> +	status = ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
> +	if (status)
> +		goto exit;
> +	/* write the data to the data reg */
> +	ql_write32(qdev, PROC_DATA, data);
> +	/* trigger the write */
> +	ql_write32(qdev, PROC_ADDR, reg);
> +	/* wait for reg to come ready */
> +	status = ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
> +	if (status)
> +		goto exit;

These two lines above are redundant. You cold also avoid the goto with
opening a new block after the first if. Or how about just...

static int ql_write_mbox_reg(struct ql_adapter *qdev, u32 reg, u32 data)
{
	/* wait for reg to come ready */
	if (ql_wait_addr_reg(qdev_ PROC_ADDR, PROC_ADDR_RDY)) {
		/* write the data to the data reg */
		ql_write32(qdev, PROC_DATA, data);
		/* trigger the write */
		ql_write32(qdev, PROC_ADDR, reg);
	}

	/* wait for reg to come ready */
	return ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
}

... omitting the need for the status variable altogether.

> +exit:
> +	return status;
> +}
> +
> +static int ql_read_mbox_reg(struct ql_adapter *qdev, u32 reg, u32 *data)
> +{
> +	int status = 0;

Same here for the goto. And no need to initialize status with a constant
which must be pulled from memory when there is no path using this
default value anyway.

> +	/* wait for reg to come ready */
> +	status = ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
> +	if (status)
> +		goto exit;
> +	/* set up for reg read */
> +	ql_write32(qdev, PROC_ADDR, reg | PROC_ADDR_R);
> +	/* wait for reg to come ready */
> +	status = ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
> +	if (status)
> +		goto exit;
> +	/* get the data */
> +	*data = ql_read32(qdev, PROC_DATA);
> +exit:
> +	return status;
> +}
> +
> +static int ql_exec_mb_cmd(struct ql_adapter *qdev, struct mbox_params *mbcp)
> +{
> +	int i, status;
> +
> +	/*
> +	 * Make sure there's nothing pending.
> +	 * This shouldn't happen.
> +	 */
> +	if (ql_read32(qdev, CSR) & CSR_HRI)
> +		return -EBUSY;
> +
> +	status = ql_sem_spinlock(qdev, SEM_PROC_REG_MASK);
> +	if (status)
> +		return -EBUSY;
> +	/*
> +	 * Fill the outbound mailboxes.
> +	 */
> +	for (i = 0; i < mbcp->in_count; i++) {
> +		status =
> +		    ql_write_mbox_reg(qdev, qdev->mailbox_in + i,
> +				      mbcp->mbox_in[i]);
> +		if (status)
> +			goto end;
> +	}
> +	/*
> +	 * Wake up the MPI firmware.
> +	 */
> +	ql_write32(qdev, CSR, CSR_CMD_SET_H2R_INT);
> +end:
> +	ql_sem_unlock(qdev, SEM_PROC_REG_MASK);	/* does flush too */
> +	return status;
> +}
> +
> +int ql_get_mb_sts(struct ql_adapter *qdev, struct mbox_params *mbcp)
> +{
> +	int i, status = 0;

Again, default value never used.

> +
> +	status = ql_sem_spinlock(qdev, SEM_PROC_REG_MASK);
> +	if (status)
> +		return -EBUSY;
> +	for (i = 0; i < mbcp->out_count; i++) {
> +		status =
> +		    ql_read_mbox_reg(qdev, qdev->mailbox_out + i,
> +				     &mbcp->mbox_out[i]);
> +		if (status) {
> +			QPRINTK(qdev, DRV, ERR, "Failed mailbox read.\n");
> +			break;
> +		}
> +	}
> +	ql_sem_unlock(qdev, SEM_PROC_REG_MASK);	/* does flush too */
> +	return status;
> +}
> +
> +static void ql_link_up(struct ql_adapter *qdev)
> +{
> +	struct mbox_params mbc;
> +	struct mbox_params *mbcp = &mbc;
> +	mbcp->out_count = 2;
> +
> +	if (ql_get_mb_sts(qdev, mbcp))
> +		goto exit;
> +
> +	qdev->link_status = mbcp->mbox_out[1];
> +	QPRINTK(qdev, DRV, ERR, "Link Up.\n");
> +	QPRINTK(qdev, DRV, ERR, "Link Status = 0x%.08x.\n", mbcp->mbox_out[1]);
> +	if (!netif_carrier_ok(qdev->ndev)) {
> +		QPRINTK(qdev, LINK, INFO, "Link is Up.\n");
> +		netif_carrier_on(qdev->ndev);
> +		netif_wake_queue(qdev->ndev);
> +	}
> +exit:
> +	/* Clear the MPI firmware status. */
> +	ql_write32(qdev, CSR, CSR_CMD_CLR_R2PCI_INT);
> +}
> +
> +static void ql_link_down(struct ql_adapter *qdev)
> +{
> +	struct mbox_params mbc;
> +	struct mbox_params *mbcp = &mbc;
> +	mbcp->out_count = 3;
> +
> +	if (ql_get_mb_sts(qdev, mbcp)) {
> +		QPRINTK(qdev, DRV, ERR, "Firmware did not initialize!\n");
> +		goto exit;
> +	}
> +
> +	if (netif_carrier_ok(qdev->ndev)) {
> +		QPRINTK(qdev, LINK, INFO, "Link is Down.\n");
> +		netif_carrier_off(qdev->ndev);
> +		netif_stop_queue(qdev->ndev);
> +	}
> +	QPRINTK(qdev, DRV, ERR, "Link Down.\n");
> +	QPRINTK(qdev, DRV, ERR, "Link Status = 0x%.08x.\n", mbcp->mbox_out[1]);
> +exit:
> +	/* Clear the MPI firmware status. */
> +	ql_write32(qdev, CSR, CSR_CMD_CLR_R2PCI_INT);
> +}
> +
> +static void ql_init_fw_done(struct ql_adapter *qdev)
> +{
> +	struct mbox_params mbc;
> +	struct mbox_params *mbcp = &mbc;
> +	mbcp->out_count = 2;
> +
> +	if (ql_get_mb_sts(qdev, mbcp)) {
> +		QPRINTK(qdev, DRV, ERR, "Firmware did not initialize!\n");
> +		goto exit;
> +	}
> +	QPRINTK(qdev, DRV, ERR, "Firmware initialized!\n");
> +	QPRINTK(qdev, DRV, ERR, "Firmware status = 0x%.08x.\n",
> +		mbcp->mbox_out[0]);
> +	QPRINTK(qdev, DRV, ERR, "Firmware Revision  = 0x%.08x.\n",
> +		mbcp->mbox_out[1]);
> +exit:
> +	/* Clear the MPI firmware status. */
> +	ql_write32(qdev, CSR, CSR_CMD_CLR_R2PCI_INT);
> +}
> +
> +void ql_mpi_work(struct work_struct *work)
> +{
> +	struct ql_adapter *qdev =
> +	    container_of(work, struct ql_adapter, mpi_work.work);
> +	struct mbox_params mbc;
> +	struct mbox_params *mbcp = &mbc;
> +	mbcp->out_count = 1;
> +
> +	while (ql_read32(qdev, STS) & STS_PI) {
> +		if (ql_get_mb_sts(qdev, mbcp)) {
> +			QPRINTK(qdev, DRV, ERR,
> +				"Could not read MPI, resetting ASIC!\n");
> +			ql_queue_asic_error(qdev);
> +		}
> +
> +		switch (mbcp->mbox_out[0]) {
> +		case AEN_LINK_UP:
> +			ql_link_up(qdev);
> +			break;
> +		case AEN_LINK_DOWN:
> +			ql_link_down(qdev);
> +			break;
> +		case AEN_FW_INIT_DONE:
> +#ifdef PALLADIUM
> +/* Palladium Workaround Start */
> +		case 0:
> +/* Palladium Workaround End */
> +#endif
> +			ql_init_fw_done(qdev);
> +			break;
> +		case AEN_FW_INIT_FAIL:
> +			break;

No breaking here...

> +		case AEN_SYS_ERR:
> +			break;

...and here necessary to make things more consistent with the lines
below. (Having no default seems ok here.)

> +		case MB_CMD_STS_GOOD:
> +		case MB_CMD_STS_INTRMDT:
> +		case MB_CMD_STS_ERR:
> +		case AEN_IDC_CMPLT:
> +		case AEN_IDC_REQ:
> +			break;
> +
> +		}
> +	}
> +	ql_enable_completion_interrupt(qdev, 0);
> +}
> +
> +void ql_mpi_reset_work(struct work_struct *work)
> +{
> +	struct ql_adapter *qdev =
> +	    container_of(work, struct ql_adapter, mpi_reset_work.work);
> +	printk(KERN_ERR "%s: Enter, qdev = %p..\n", __func__, qdev);
> +}

Another inconsistency: you're not using QPRINTK() like before. Is this
intended?


Franco

Re: [PATCH 5/8] [RFC] qlge: Add main source module qlge_main.c

[Franco Fichtner]

Ron Mercer wrote:

[snipped some code]

> +static int ql_wait_port_init_cmplt(struct ql_adapter *qdev)
> +{
> +	int count = 100;
> +	u32 temp;
> +
> +	while (count) {
> +		temp = ql_read32(qdev, STS);
> +		if (temp & qdev->port_init)
> +			return 0;
> +		mdelay(5);

Wrost case: delaying for 500ms... msleep() here please.

> +		QPRINTK(qdev, LINK, INFO, "Wait for MAC Port to Initialize.\n");

I don't know what QPRINTK does, but it gets executed 100 times. That
can't possibly be intended?

> +		count--;
> +	}
> +	return -ETIMEDOUT;
> +}
> +
> +/* The CFG register is used to download TX and RX control blocks
> + * to the chip. This function waits for an operation to complete.
> + */
> +static int ql_wait_cfg(struct ql_adapter *qdev, u32 bit)
> +{
> +	int count = MSLEEP_COUNT;
> +	u32 temp;
> +
> +	while (count) {
> +		temp = ql_read32(qdev, CFG);
> +		if (!(temp & bit))
> +			return 0;
> +		if (temp & CFG_LE)
> +			return -EIO;
> +		spin_unlock(&qdev->hw_lock);
> +		msleep(MSLEEP_DELAY);
> +		spin_lock(&qdev->hw_lock);

If this is why mdelay() is used in the other places... keeping the locks
shouldn't hurt when changing them to msleep()? I don't see how a
possible deadlock could occur in the mdelay() scenarios. And besides, 
you seem to operate your spinlocks on a higher level than e.g. this
function? Wouldn't that render multi-cpu usage pratically useless?

> +		count--;
> +	}
> +	return -ETIMEDOUT;
> +}
> +
> +/* Used to issue init control blocks to hw. Maps control block,
> + * sets address, triggers download, waits for completion.
> + */
> +int ql_write_cfg(struct ql_adapter *qdev, void *ptr, int size, u32 bit,
> +		 u16 q_id)
> +{
> +	u64 map;
> +	int status = 0;
> +	int direction;
> +	u32 mask;
> +	u32 value;
> +
> +	direction =
> +	    (bit & (CFG_LRQ | CFG_LR | CFG_LCQ)) ? PCI_DMA_TODEVICE :
> +	    PCI_DMA_FROMDEVICE;
> +
> +	map = pci_map_single(qdev->pdev, ptr, size, direction);
> +	if (pci_dma_mapping_error(map)) {
> +		QPRINTK(qdev, IFUP, ERR, "Couldn't map DMA area.\n");
> +		return -ENOMEM;
> +	}
> +
> +	status = ql_wait_cfg(qdev, bit);
> +	if (status) {
> +		QPRINTK(qdev, IFUP, ERR,
> +			"Timed out waiting for CFG to come ready.\n");
> +		goto exit;
> +	}
> +
> +	status = ql_sem_spinlock(qdev, SEM_ICB_MASK);
> +	if (status)
> +		goto exit;
> +	ql_write32(qdev, ICB_L, (u32) map);
> +	ql_write32(qdev, ICB_H, (u32) (map >> 32));
> +	ql_sem_unlock(qdev, SEM_ICB_MASK);	/* does flush too */
> +
> +	mask = CFG_Q_MASK | (bit << 16);
> +	value = bit | (q_id << CFG_Q_SHIFT);
> +	ql_write32(qdev, CFG, (mask | value));
> +
> +	/*
> +	 * Wait for the bit to clear after signaling hw.
> +	 */
> +	status = ql_wait_cfg(qdev, bit);
> +exit:
> +	pci_unmap_single(qdev->pdev, map, size, direction);
> +	return status;
> +}
> +
> +/* This chip has several addr/data register pairs that are used
> + * to index into another set of registers.  This function waits
> + * for a specified register set to be ready for access.
> + * Examples would be setting up the CAM with MAC addresses, setting
> + * up the frame routing table.
> + */
> +static int ql_wait_idx_reg(struct ql_adapter *qdev, u32 reg, u32 flag)
> +{
> +	int count = 200;
> +	u32 temp;
> +
> +	while (count) {
> +		temp = ql_read32(qdev, reg);
> +		if (temp & flag)
> +			return 0;
> +		mdelay(5);

Delaying for a 1000ms worst case.

> +		count--;
> +	}
> +	return -ETIMEDOUT;
> +}

[snipped more code]

> +static int ql_port_initialize(struct ql_adapter *qdev)
> +{
> +	int status = 0;
> +	u32 data;
> +
> +	if (ql_sem_trylock(qdev, qdev->xg_sem_mask)) {
> +		/* Another function has the semaphore, so
> +		 * wait for the port init bit to come ready.
> +		 */
> +		QPRINTK(qdev, LINK, INFO,
> +			"Another function has the semaphore, so wait for the port init bit to come ready.\n");
> +		status = ql_wait_port_init_cmplt(qdev);
> +		if (status) {
> +			QPRINTK(qdev, LINK, CRIT,
> +				"Port initialize timed out.\n");
> +		}
> +		return status;
> +	}
> +
> +	QPRINTK(qdev, LINK, INFO, "Got xgmac semaphore!.\n");
> +	/* Set the core reset. */
> +	status = ql_read_xgmac_reg(qdev, GLOBAL_CFG, &data);
> +	if (status)
> +		goto end;
> +	data |= GLOBAL_CFG_RESET;
> +	status = ql_write_xgmac_reg(qdev, GLOBAL_CFG, data);
> +	if (status)
> +		goto end;
> +
> +	mdelay(100);

Again.

> +
> +	/* Clear the core reset and turn on jumbo for receiver. */
> +	data &= ~GLOBAL_CFG_RESET;	/* Clear core reset. */
> +	data |= GLOBAL_CFG_JUMBO;	/* Turn on jumbo. */
> +	data |= GLOBAL_CFG_TX_STAT_EN;
> +	data |= GLOBAL_CFG_RX_STAT_EN;
> +	status = ql_write_xgmac_reg(qdev, GLOBAL_CFG, data);
> +	if (status)
> +		goto end;
> +
> +	/* Enable transmitter, and clear it's reset. */
> +	status = ql_read_xgmac_reg(qdev, TX_CFG, &data);
> +	if (status)
> +		goto end;
> +	data &= ~TX_CFG_RESET;	/* Clear the TX MAC reset. */
> +	data |= TX_CFG_EN;	/* Enable the transmitter. */
> +	status = ql_write_xgmac_reg(qdev, TX_CFG, data);
> +	if (status)
> +		goto end;
> +
> +	/* Enable receiver and clear it's reset. */
> +	status = ql_read_xgmac_reg(qdev, RX_CFG, &data);
> +	if (status)
> +		goto end;
> +	data &= ~RX_CFG_RESET;	/* Clear the RX MAC reset. */
> +	data |= RX_CFG_EN;	/* Enable the receiver. */
> +	status = ql_write_xgmac_reg(qdev, RX_CFG, data);
> +	if (status)
> +		goto end;
> +
> +	/* Turn on jumbo. */
> +	status =
> +	    ql_write_xgmac_reg(qdev, MAC_TX_PARAMS, MAC_TX_PARAMS_JUMBO | (0x2580 << 16));
> +	if (status)
> +		goto end;
> +	status =
> +	    ql_write_xgmac_reg(qdev, MAC_RX_PARAMS, 0x2580);
> +	if (status)
> +		goto end;
> +
> +	/* Signal to the world that the port is enabled.        */
> +	ql_write32(qdev, STS, ((qdev->port_init << 16) | qdev->port_init));
> +end:
> +	ql_sem_unlock(qdev, qdev->xg_sem_mask);
> +	return status;
> +}
> +
> +/* Get the next large buffer. */
> +struct bq_desc *ql_get_curr_lbuf(struct rx_ring *rx_ring)
> +{
> +	struct bq_desc *lbq_desc = &rx_ring->lbq[rx_ring->lbq_curr_idx];
> +	rx_ring->lbq_curr_idx++;
> +	if (rx_ring->lbq_curr_idx == rx_ring->lbq_len)
> +		rx_ring->lbq_curr_idx = 0;
> +	rx_ring->lbq_free_cnt++;
> +	return lbq_desc;
> +}

[ remaining code snipped, a bit too much for today ]


Franco

Re: [PATCH 6/8] [RFC] qlge: Add mgmt port xface file qlge_mpi.c

[Ron Mercer]

On Thu, Sep 11, 2008 at 10:03:19AM +0200, Franco Fichtner wrote:
> Ron Mercer wrote:
> >Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
> >---
> > drivers/net/qlge/qlge_mpi.c |  228 
> > +++++++++++++++++++++++++++++++++++++++++++
> > 1 files changed, 228 insertions(+), 0 deletions(-)
> > create mode 100644 drivers/net/qlge/qlge_mpi.c
> >
> >diff --git a/drivers/net/qlge/qlge_mpi.c b/drivers/net/qlge/qlge_mpi.c
> >new file mode 100644
> >index 0000000..f235fc5
> >--- /dev/null
> >+++ b/drivers/net/qlge/qlge_mpi.c
> >@@ -0,0 +1,228 @@
> >+#include "qlge.h"
> >+
> >+/*
> >+ * Returns zero on success.
> >+ */
> >+static int ql_wait_mbx_cmd_cmplt(struct ql_adapter *qdev)
> >+{
> >+	int count = 50;
> >+	u32 temp;
> >+
> >+	while (count) {
> >+		temp = ql_read32(qdev, STS);
> >+		if (temp & STS_PI)
> >+			return 0;
> >+		mdelay(5);
> 
> Do you really want to delay execution for 250ms in worst case (timeout)
> scenarios? A msleep() would be more graceful.
>

We do need to wait this long as the MPI firmware will be handling
mailbox commands for an FCOE function as well as this NIC function.
You're right about msleep() being a better choice and I will change it
for the next submission.

> >+		count--;
> >+	}
> >+	return -ETIMEDOUT;
> >+}
> >+
> >+static int ql_write_mbox_reg(struct ql_adapter *qdev, u32 reg, u32 data)
> >+{
> >+	int status = 0;
> >+	/* wait for reg to come ready */
> >+	status = ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
> >+	if (status)
> >+		goto exit;
> >+	/* write the data to the data reg */
> >+	ql_write32(qdev, PROC_DATA, data);
> >+	/* trigger the write */
> >+	ql_write32(qdev, PROC_ADDR, reg);
> >+	/* wait for reg to come ready */
> >+	status = ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
> >+	if (status)
> >+		goto exit;
> 
> These two lines above are redundant. You cold also avoid the goto with
> opening a new block after the first if. Or how about just...
> 

Right again.  I was waiting before and after the function.  You only
need to wait at one of them.  I will remove the trailing wait.

> static int ql_write_mbox_reg(struct ql_adapter *qdev, u32 reg, u32 data)
> {
> 	/* wait for reg to come ready */
> 	if (ql_wait_addr_reg(qdev_ PROC_ADDR, PROC_ADDR_RDY)) {
> 		/* write the data to the data reg */
> 		ql_write32(qdev, PROC_DATA, data);
> 		/* trigger the write */
> 		ql_write32(qdev, PROC_ADDR, reg);
> 	}
> 
> 	/* wait for reg to come ready */
> 	return ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
> }
> 
> ... omitting the need for the status variable altogether.

I'll still need status, but won't initialize it and will drop the
trailing wait.

> 
> >+exit:
> >+	return status;
> >+}
> >+
> >+static int ql_read_mbox_reg(struct ql_adapter *qdev, u32 reg, u32 *data)
> >+{
> >+	int status = 0;
> 
> Same here for the goto. And no need to initialize status with a constant
> which must be pulled from memory when there is no path using this
> default value anyway.

done...

> 
> >+	/* wait for reg to come ready */
> >+	status = ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
> >+	if (status)
> >+		goto exit;
> >+	/* set up for reg read */
> >+	ql_write32(qdev, PROC_ADDR, reg | PROC_ADDR_R);
> >+	/* wait for reg to come ready */
> >+	status = ql_wait_addr_reg(qdev, PROC_ADDR, PROC_ADDR_RDY);
> >+	if (status)
> >+		goto exit;
> >+	/* get the data */
> >+	*data = ql_read32(qdev, PROC_DATA);
> >+exit:
> >+	return status;
> >+}
> >+
> >+static int ql_exec_mb_cmd(struct ql_adapter *qdev, struct mbox_params 
> >*mbcp)
> >+{
> >+	int i, status;
> >+
> >+	/*
> >+	 * Make sure there's nothing pending.
> >+	 * This shouldn't happen.
> >+	 */
> >+	if (ql_read32(qdev, CSR) & CSR_HRI)
> >+		return -EBUSY;
> >+
> >+	status = ql_sem_spinlock(qdev, SEM_PROC_REG_MASK);
> >+	if (status)
> >+		return -EBUSY;
> >+	/*
> >+	 * Fill the outbound mailboxes.
> >+	 */
> >+	for (i = 0; i < mbcp->in_count; i++) {
> >+		status =
> >+		    ql_write_mbox_reg(qdev, qdev->mailbox_in + i,
> >+				      mbcp->mbox_in[i]);
> >+		if (status)
> >+			goto end;
> >+	}
> >+	/*
> >+	 * Wake up the MPI firmware.
> >+	 */
> >+	ql_write32(qdev, CSR, CSR_CMD_SET_H2R_INT);
> >+end:
> >+	ql_sem_unlock(qdev, SEM_PROC_REG_MASK);	/* does flush too */
> >+	return status;
> >+}
> >+
> >+int ql_get_mb_sts(struct ql_adapter *qdev, struct mbox_params *mbcp)
> >+{
> >+	int i, status = 0;
> 
> Again, default value never used.

Done...

> 
> >+
> >+	status = ql_sem_spinlock(qdev, SEM_PROC_REG_MASK);
> >+	if (status)
> >+		return -EBUSY;
> >+	for (i = 0; i < mbcp->out_count; i++) {
> >+		status =
> >+		    ql_read_mbox_reg(qdev, qdev->mailbox_out + i,
> >+				     &mbcp->mbox_out[i]);
> >+		if (status) {
> >+			QPRINTK(qdev, DRV, ERR, "Failed mailbox read.\n");
> >+			break;
> >+		}
> >+	}
> >+	ql_sem_unlock(qdev, SEM_PROC_REG_MASK);	/* does flush too */
> >+	return status;
> >+}
> >+
> >+static void ql_link_up(struct ql_adapter *qdev)
> >+{
> >+	struct mbox_params mbc;
> >+	struct mbox_params *mbcp = &mbc;
> >+	mbcp->out_count = 2;
> >+
> >+	if (ql_get_mb_sts(qdev, mbcp))
> >+		goto exit;
> >+
> >+	qdev->link_status = mbcp->mbox_out[1];
> >+	QPRINTK(qdev, DRV, ERR, "Link Up.\n");
> >+	QPRINTK(qdev, DRV, ERR, "Link Status = 0x%.08x.\n", 
> >mbcp->mbox_out[1]);
> >+	if (!netif_carrier_ok(qdev->ndev)) {
> >+		QPRINTK(qdev, LINK, INFO, "Link is Up.\n");
> >+		netif_carrier_on(qdev->ndev);
> >+		netif_wake_queue(qdev->ndev);
> >+	}
> >+exit:
> >+	/* Clear the MPI firmware status. */
> >+	ql_write32(qdev, CSR, CSR_CMD_CLR_R2PCI_INT);
> >+}
> >+
> >+static void ql_link_down(struct ql_adapter *qdev)
> >+{
> >+	struct mbox_params mbc;
> >+	struct mbox_params *mbcp = &mbc;
> >+	mbcp->out_count = 3;
> >+
> >+	if (ql_get_mb_sts(qdev, mbcp)) {
> >+		QPRINTK(qdev, DRV, ERR, "Firmware did not initialize!\n");
> >+		goto exit;
> >+	}
> >+
> >+	if (netif_carrier_ok(qdev->ndev)) {
> >+		QPRINTK(qdev, LINK, INFO, "Link is Down.\n");
> >+		netif_carrier_off(qdev->ndev);
> >+		netif_stop_queue(qdev->ndev);
> >+	}
> >+	QPRINTK(qdev, DRV, ERR, "Link Down.\n");
> >+	QPRINTK(qdev, DRV, ERR, "Link Status = 0x%.08x.\n", 
> >mbcp->mbox_out[1]);
> >+exit:
> >+	/* Clear the MPI firmware status. */
> >+	ql_write32(qdev, CSR, CSR_CMD_CLR_R2PCI_INT);
> >+}
> >+
> >+static void ql_init_fw_done(struct ql_adapter *qdev)
> >+{
> >+	struct mbox_params mbc;
> >+	struct mbox_params *mbcp = &mbc;
> >+	mbcp->out_count = 2;
> >+
> >+	if (ql_get_mb_sts(qdev, mbcp)) {
> >+		QPRINTK(qdev, DRV, ERR, "Firmware did not initialize!\n");
> >+		goto exit;
> >+	}
> >+	QPRINTK(qdev, DRV, ERR, "Firmware initialized!\n");
> >+	QPRINTK(qdev, DRV, ERR, "Firmware status = 0x%.08x.\n",
> >+		mbcp->mbox_out[0]);
> >+	QPRINTK(qdev, DRV, ERR, "Firmware Revision  = 0x%.08x.\n",
> >+		mbcp->mbox_out[1]);
> >+exit:
> >+	/* Clear the MPI firmware status. */
> >+	ql_write32(qdev, CSR, CSR_CMD_CLR_R2PCI_INT);
> >+}
> >+
> >+void ql_mpi_work(struct work_struct *work)
> >+{
> >+	struct ql_adapter *qdev =
> >+	    container_of(work, struct ql_adapter, mpi_work.work);
> >+	struct mbox_params mbc;
> >+	struct mbox_params *mbcp = &mbc;
> >+	mbcp->out_count = 1;
> >+
> >+	while (ql_read32(qdev, STS) & STS_PI) {
> >+		if (ql_get_mb_sts(qdev, mbcp)) {
> >+			QPRINTK(qdev, DRV, ERR,
> >+				"Could not read MPI, resetting ASIC!\n");
> >+			ql_queue_asic_error(qdev);
> >+		}
> >+
> >+		switch (mbcp->mbox_out[0]) {
> >+		case AEN_LINK_UP:
> >+			ql_link_up(qdev);
> >+			break;
> >+		case AEN_LINK_DOWN:
> >+			ql_link_down(qdev);
> >+			break;
> >+		case AEN_FW_INIT_DONE:
> >+#ifdef PALLADIUM
> >+/* Palladium Workaround Start */
> >+		case 0:
> >+/* Palladium Workaround End */
> >+#endif
> >+			ql_init_fw_done(qdev);
> >+			break;
> >+		case AEN_FW_INIT_FAIL:
> >+			break;
> 
> No breaking here...

Thanks for bringing it to my attention.  I am in the process of cleaning this up.

> 
> >+		case AEN_SYS_ERR:
> >+			break;
> 
> ...and here necessary to make things more consistent with the lines
> below. (Having no default seems ok here.)
>

This wasn't done and kind of fell through the cracks.  It will be done
in the next submittal.

> >+		case MB_CMD_STS_GOOD:
> >+		case MB_CMD_STS_INTRMDT:
> >+		case MB_CMD_STS_ERR:
> >+		case AEN_IDC_CMPLT:
> >+		case AEN_IDC_REQ:
> >+			break;
> >+
> >+		}
> >+	}
> >+	ql_enable_completion_interrupt(qdev, 0);
> >+}
> >+
> >+void ql_mpi_reset_work(struct work_struct *work)
> >+{
> >+	struct ql_adapter *qdev =
> >+	    container_of(work, struct ql_adapter, mpi_reset_work.work);
> >+	printk(KERN_ERR "%s: Enter, qdev = %p..\n", __func__, qdev);
> >+}
> 
> Another inconsistency: you're not using QPRINTK() like before. Is this
> intended?

Not intended.  I'll fix it.


Thanks for your help.
-Ron

Re: [PATCH 5/8] [RFC] qlge: Add main source module qlge_main.c

[Ron Mercer]

On Thu, Sep 11, 2008 at 10:39:19AM +0200, Franco Fichtner wrote:

Hello Franco,
Thanks very much for your comments/suggestions.
Regarding ql_wait_idx_reg() and ql_wait_addr_reg() they provide waiting
while gaining access for read/writes to/from a secondary set of
registers.  To my understanding, you can't sleep while holding a
spinlock.  I tried this before and saw massive warnings.  I have
"Spinlock debugging: sleep-inside-spinlock checking" turned on in my
kernel and perhaps that's why I saw them.
At that point I changed from msleep to mdelay.
After reviewing your comments I've reduced and standardized the mdelay
wait to 5ms with a count of 50.
These secondary registers are
accessed only during open(), reset(), and a few
netdev-API like set_multi and add_vlan_vid.

> Ron Mercer wrote:
> 
> [snipped some code]
> 
> >+static int ql_wait_port_init_cmplt(struct ql_adapter *qdev)
> >+{
> >+	int count = 100;
> >+	u32 temp;
> >+
> >+	while (count) {
> >+		temp = ql_read32(qdev, STS);
> >+		if (temp & qdev->port_init)
> >+			return 0;
> >+		mdelay(5);
> 
> Wrost case: delaying for 500ms... msleep() here please.

Again, to my understanding, sleeping while holding a lock is
problematic.  I have changed this wait to 5ms * 50.

> 
> >+		QPRINTK(qdev, LINK, INFO, "Wait for MAC Port to 
> >Initialize.\n");
> 
> I don't know what QPRINTK does, but it gets executed 100 times. That
> can't possibly be intended?

Not intended.  It's gone.  Thanks.

> 
> >+		count--;
> >+	}
> >+	return -ETIMEDOUT;
> >+}
> >+
> >+/* The CFG register is used to download TX and RX control blocks
> >+ * to the chip. This function waits for an operation to complete.
> >+ */
> >+static int ql_wait_cfg(struct ql_adapter *qdev, u32 bit)
> >+{
> >+	int count = MSLEEP_COUNT;
> >+	u32 temp;
> >+
> >+	while (count) {
> >+		temp = ql_read32(qdev, CFG);
> >+		if (!(temp & bit))
> >+			return 0;
> >+		if (temp & CFG_LE)
> >+			return -EIO;
> >+		spin_unlock(&qdev->hw_lock);
> >+		msleep(MSLEEP_DELAY);
> >+		spin_lock(&qdev->hw_lock);
> 
> If this is why mdelay() is used in the other places... keeping the locks
> shouldn't hurt when changing them to msleep()? I don't see how a
> possible deadlock could occur in the mdelay() scenarios. And besides, 
> you seem to operate your spinlocks on a higher level than e.g. this
> function? Wouldn't that render multi-cpu usage pratically useless?

I've gotten rid of the unlock/lock and used mdelay() for 5ms * 50 as
above.  This is used to download a control block to the chip and then
wait for it to initialize internal data structures.  Only used during
open() and ethtool->set_coalesce() (if the device is up).

> 
> >+		count--;
> >+	}
> >+	return -ETIMEDOUT;
> >+}
> >+
> >+/* Used to issue init control blocks to hw. Maps control block,
> >+ * sets address, triggers download, waits for completion.
> >+ */
> >+int ql_write_cfg(struct ql_adapter *qdev, void *ptr, int size, u32 bit,
> >+		 u16 q_id)
> >+{
> >+	u64 map;
> >+	int status = 0;
> >+	int direction;
> >+	u32 mask;
> >+	u32 value;
> >+
> >+	direction =
> >+	    (bit & (CFG_LRQ | CFG_LR | CFG_LCQ)) ? PCI_DMA_TODEVICE :
> >+	    PCI_DMA_FROMDEVICE;
> >+
> >+	map = pci_map_single(qdev->pdev, ptr, size, direction);
> >+	if (pci_dma_mapping_error(map)) {
> >+		QPRINTK(qdev, IFUP, ERR, "Couldn't map DMA area.\n");
> >+		return -ENOMEM;
> >+	}
> >+
> >+	status = ql_wait_cfg(qdev, bit);
> >+	if (status) {
> >+		QPRINTK(qdev, IFUP, ERR,
> >+			"Timed out waiting for CFG to come ready.\n");
> >+		goto exit;
> >+	}
> >+
> >+	status = ql_sem_spinlock(qdev, SEM_ICB_MASK);
> >+	if (status)
> >+		goto exit;
> >+	ql_write32(qdev, ICB_L, (u32) map);
> >+	ql_write32(qdev, ICB_H, (u32) (map >> 32));
> >+	ql_sem_unlock(qdev, SEM_ICB_MASK);	/* does flush too */
> >+
> >+	mask = CFG_Q_MASK | (bit << 16);
> >+	value = bit | (q_id << CFG_Q_SHIFT);
> >+	ql_write32(qdev, CFG, (mask | value));
> >+
> >+	/*
> >+	 * Wait for the bit to clear after signaling hw.
> >+	 */
> >+	status = ql_wait_cfg(qdev, bit);
> >+exit:
> >+	pci_unmap_single(qdev->pdev, map, size, direction);
> >+	return status;
> >+}
> >+
> >+/* This chip has several addr/data register pairs that are used
> >+ * to index into another set of registers.  This function waits
> >+ * for a specified register set to be ready for access.
> >+ * Examples would be setting up the CAM with MAC addresses, setting
> >+ * up the frame routing table.
> >+ */
> >+static int ql_wait_idx_reg(struct ql_adapter *qdev, u32 reg, u32 flag)
> >+{
> >+	int count = 200;
> >+	u32 temp;
> >+
> >+	while (count) {
> >+		temp = ql_read32(qdev, reg);
> >+		if (temp & flag)
> >+			return 0;
> >+		mdelay(5);
> 
> Delaying for a 1000ms worst case.

See comments at top.

> 
> >+		count--;
> >+	}
> >+	return -ETIMEDOUT;
> >+}
> 
> [snipped more code]
> 
> >+static int ql_port_initialize(struct ql_adapter *qdev)
> >+{
> >+	int status = 0;
> >+	u32 data;
> >+
> >+	if (ql_sem_trylock(qdev, qdev->xg_sem_mask)) {
> >+		/* Another function has the semaphore, so
> >+		 * wait for the port init bit to come ready.
> >+		 */
> >+		QPRINTK(qdev, LINK, INFO,
> >+			"Another function has the semaphore, so wait for the 
> >port init bit to come ready.\n");
> >+		status = ql_wait_port_init_cmplt(qdev);
> >+		if (status) {
> >+			QPRINTK(qdev, LINK, CRIT,
> >+				"Port initialize timed out.\n");
> >+		}
> >+		return status;
> >+	}
> >+
> >+	QPRINTK(qdev, LINK, INFO, "Got xgmac semaphore!.\n");
> >+	/* Set the core reset. */
> >+	status = ql_read_xgmac_reg(qdev, GLOBAL_CFG, &data);
> >+	if (status)
> >+		goto end;
> >+	data |= GLOBAL_CFG_RESET;
> >+	status = ql_write_xgmac_reg(qdev, GLOBAL_CFG, data);
> >+	if (status)
> >+		goto end;
> >+
> >+	mdelay(100);
> 
> Again.

This shouldn't be there because it's followed by a wait before another
write.  It's gone now.

> 
> >+
> >+	/* Clear the core reset and turn on jumbo for receiver. */
> >+	data &= ~GLOBAL_CFG_RESET;	/* Clear core reset. */
> >+	data |= GLOBAL_CFG_JUMBO;	/* Turn on jumbo. */
> >+	data |= GLOBAL_CFG_TX_STAT_EN;
> >+	data |= GLOBAL_CFG_RX_STAT_EN;
> >+	status = ql_write_xgmac_reg(qdev, GLOBAL_CFG, data);
> >+	if (status)
> >+		goto end;
> >+
> >+	/* Enable transmitter, and clear it's reset. */
> >+	status = ql_read_xgmac_reg(qdev, TX_CFG, &data);
> >+	if (status)
> >+		goto end;
> >+	data &= ~TX_CFG_RESET;	/* Clear the TX MAC reset. */
> >+	data |= TX_CFG_EN;	/* Enable the transmitter. */
> >+	status = ql_write_xgmac_reg(qdev, TX_CFG, data);
> >+	if (status)
> >+		goto end;
> >+
> >+	/* Enable receiver and clear it's reset. */
> >+	status = ql_read_xgmac_reg(qdev, RX_CFG, &data);
> >+	if (status)
> >+		goto end;
> >+	data &= ~RX_CFG_RESET;	/* Clear the RX MAC reset. */
> >+	data |= RX_CFG_EN;	/* Enable the receiver. */
> >+	status = ql_write_xgmac_reg(qdev, RX_CFG, data);
> >+	if (status)
> >+		goto end;
> >+
> >+	/* Turn on jumbo. */
> >+	status =
> >+	    ql_write_xgmac_reg(qdev, MAC_TX_PARAMS, MAC_TX_PARAMS_JUMBO | 
> >(0x2580 << 16));
> >+	if (status)
> >+		goto end;
> >+	status =
> >+	    ql_write_xgmac_reg(qdev, MAC_RX_PARAMS, 0x2580);
> >+	if (status)
> >+		goto end;
> >+
> >+	/* Signal to the world that the port is enabled.        */
> >+	ql_write32(qdev, STS, ((qdev->port_init << 16) | qdev->port_init));
> >+end:
> >+	ql_sem_unlock(qdev, qdev->xg_sem_mask);
> >+	return status;
> >+}
> >+
> >+/* Get the next large buffer. */
> >+struct bq_desc *ql_get_curr_lbuf(struct rx_ring *rx_ring)
> >+{
> >+	struct bq_desc *lbq_desc = &rx_ring->lbq[rx_ring->lbq_curr_idx];
> >+	rx_ring->lbq_curr_idx++;
> >+	if (rx_ring->lbq_curr_idx == rx_ring->lbq_len)
> >+		rx_ring->lbq_curr_idx = 0;
> >+	rx_ring->lbq_free_cnt++;
> >+	return lbq_desc;
> >+}
> 
> [ remaining code snipped, a bit too much for today ]
> 
> 
> Franco

Re: [PATCH 5/8] [RFC] qlge: Add main source module qlge_main.c

[Franco Fichtner]

Hi Ron,

Thanks for the clarification. 4000 lines of code are just too much to
grasp at the first glance. :)

> Regarding ql_wait_idx_reg() and ql_wait_addr_reg() they provide waiting
> while gaining access for read/writes to/from a secondary set of
> registers.

These registers are once per hardware, right? Then your spinlocking
would do nothing on single CPU systems, because it won't get into the
binaries. Meaning: your registers are NOT protected the way you would
have hoped. And even with SMP systems... if another CPU hits a locked
spinlock it does nothing but wait, quite synchronously to your mdelay()
loop. So both scenarios are rather suboptimal. If that's how things are,
you're better off using a semaphore.

On non-SMP systems, you're gonna put another access on the waiting list
by using a semaphore, which in return will give you time to finish your
operations on the registers and free the semaphore. And, last but not
least, SMP systems will do work they otherwise would not be able to do.

There is just the slight problem of ql_wait_idx_reg() and
ql_wait_addr_reg() being executed from interrupt context? If that is the
case, then you can't use the standard semaphores, because sleeping isn't
allowed. I do hope that is not the case...

> To my understanding, you can't sleep while holding a
> spinlock.  I tried this before and saw massive warnings.  I have
> "Spinlock debugging: sleep-inside-spinlock checking" turned on in my
> kernel and perhaps that's why I saw them.

You'd normally use spinlocks in interrupt context where you just have to
make sure no other CPU mangles with your variables or hardware registers
the fastest way possible. You don't keep a spinlock forever, not even
for the course of a few function calls, which will make the code harder
to read, thus harder to understand, and thus harder to debug.

The warning messages are right, but (I think) they are intended to avoid 
deadlocks as early as possible. Though, with msleep() I don't think
you'll get into any more serious problems than before, because unless 
the Kernel is really not doing what it should, you should always get
back to your loop. Using schedule() and wait queues in spinlocked 
scenarios is a whole other thing. (Anyone, please correct me if I'm wrong.)

> At that point I changed from msleep to mdelay.
> After reviewing your comments I've reduced and standardized the mdelay
> wait to 5ms with a count of 50.

It may help introduce defines to get rid of magic numbers inside the
code as well. Something like:

#define QLGE_TIMEOUT_COUNT	50
#define QLGE_TIMEOUT_DELAY	5

That will help maintaining code and makes it more easily readable (and
consistent as a bonus... less lines to update).

> These secondary registers are
> accessed only during open(), reset(), and a few
> netdev-API like set_multi and add_vlan_vid.

Okay, I see. But still, I get the vibe that this is already a bit too
much to justify keeping the current way of locking in the code. Sooner
or later someone else will complain about this. ;)


Franco

Re: [PATCH 5/8] [RFC] qlge: Add main source module qlge_main.c

[Ron Mercer]

Hi Franco,

I have cleaned up a lot of the code per your suggestions in this thread and will
do another submission this afternoon.
Regarding the delay/sleep, I've changed from mdelay to udelay and reduced the loop
into the 10s of microseconds instead of the hundreds of milliseconds.
I found out the milliseconds was intended for an emulated test
environment and not for the silicon.  Thanks again for bringing this to
my attention.

Regards,
Ron Mercer


On Fri, Sep 12, 2008 at 10:15:36AM +0200, Franco Fichtner wrote:
> Hi Ron,
> 
> Thanks for the clarification. 4000 lines of code are just too much to
> grasp at the first glance. :)
> 
> >Regarding ql_wait_idx_reg() and ql_wait_addr_reg() they provide waiting
> >while gaining access for read/writes to/from a secondary set of
> >registers.
> 
> These registers are once per hardware, right? Then your spinlocking
> would do nothing on single CPU systems, because it won't get into the
> binaries. Meaning: your registers are NOT protected the way you would
> have hoped. And even with SMP systems... if another CPU hits a locked
> spinlock it does nothing but wait, quite synchronously to your mdelay()
> loop. So both scenarios are rather suboptimal. If that's how things are,
> you're better off using a semaphore.
> 
> On non-SMP systems, you're gonna put another access on the waiting list
> by using a semaphore, which in return will give you time to finish your
> operations on the registers and free the semaphore. And, last but not
> least, SMP systems will do work they otherwise would not be able to do.
> 
> There is just the slight problem of ql_wait_idx_reg() and
> ql_wait_addr_reg() being executed from interrupt context? If that is the
> case, then you can't use the standard semaphores, because sleeping isn't
> allowed. I do hope that is not the case...
> 
> >To my understanding, you can't sleep while holding a
> >spinlock.  I tried this before and saw massive warnings.  I have
> >"Spinlock debugging: sleep-inside-spinlock checking" turned on in my
> >kernel and perhaps that's why I saw them.
> 
> You'd normally use spinlocks in interrupt context where you just have to
> make sure no other CPU mangles with your variables or hardware registers
> the fastest way possible. You don't keep a spinlock forever, not even
> for the course of a few function calls, which will make the code harder
> to read, thus harder to understand, and thus harder to debug.
> 
> The warning messages are right, but (I think) they are intended to avoid 
> deadlocks as early as possible. Though, with msleep() I don't think
> you'll get into any more serious problems than before, because unless 
> the Kernel is really not doing what it should, you should always get
> back to your loop. Using schedule() and wait queues in spinlocked 
> scenarios is a whole other thing. (Anyone, please correct me if I'm wrong.)
> 
> >At that point I changed from msleep to mdelay.
> >After reviewing your comments I've reduced and standardized the mdelay
> >wait to 5ms with a count of 50.
> 
> It may help introduce defines to get rid of magic numbers inside the
> code as well. Something like:
> 
> #define QLGE_TIMEOUT_COUNT	50
> #define QLGE_TIMEOUT_DELAY	5
> 
> That will help maintaining code and makes it more easily readable (and
> consistent as a bonus... less lines to update).
> 
> >These secondary registers are
> >accessed only during open(), reset(), and a few
> >netdev-API like set_multi and add_vlan_vid.
> 
> Okay, I see. But still, I get the vibe that this is already a bit too
> much to justify keeping the current way of locking in the code. Sooner
> or later someone else will complain about this. ;)
> 
> 
> Franco