Re: Marvell 88E609x switch?

[Gary Thomas <gary@mlbassoc.com>]

Lennert Buytenhek wrote:
> On Fri, Feb 27, 2009 at 07:55:29AM -0700, Gary Thomas wrote:
> 
>>>>>>>>> Also, can you show me what you're filling the dsa platform data
>>>>>>>>> structure with?
>>>>>>>> struct dsa_platform_data _switch_data = {
>>>>>>>>     .port_names[0]  = "lan1.1",
>>>>>>>>     .port_names[1]  = "lan1.2",
>>>>>>>>     .port_names[2]  = "lan1.3",
>>>>>>>>     .port_names[3]  = "lan1.4",
>>>>>>>>     .port_names[4]  = "lan1.5",
>>>>>>>>     .port_names[5]  = "lan1.6",
>>>>>>>>     .port_names[6]  = "lan1.7",
>>>>>>>>     .port_names[7]  = "lan1.8",
>>>>>>>>     .port_names[10]  = "cpu",
>>>>>>>>     .sw_addr = 1,
>>>>>>>> };
>>>>>>> Just this should do the trick.  So what's not working -- are the
>>>>>>> interfaces not showing up?  Or packet RX/TX isn't working?  Or
>>>>>>> something else?
>>>>>> It won't let me bring up eth0 (my scripts try to run DHCP):
>>>>>>   starting network interfaces...
>>>>>>   24520:01 not found
>>>>>>   eth0: Could not attach to PHY
>>>>>>   ip: SIOCSIFFLAGS: No such device
>>>>>>
>>>>>> As for the other devices, they do show up if I let eth0 try to
>>>>>> attach to the PHY:
>>>>> OK.  If you try to cheat the gianfar driver by having it attach to
>>>>> the PHY for lan1.1, and plug a network cable into lan1.1 so that the
>>>>> link goes up and gianfar thinks that the link on eth0 is up, does that
>>>>> enable you to pass packets over any of the switch interfaces?  That
>>>>> should be working now in this stage.
>>>> So, what name do I use when the gianfar is trying to attach?
>>>> It makes this call:
>>>>   phydev = phy_connect(dev, phy_id, &adjust_link, 0, interface);
>>>> where phy_id="24520:01".
>>>>
>>>> Using "24520:01:00" gets an error:
>>>>   eth0: 24520:01:00 already attached
>>>>
>>>> Maybe the DSA layer/driver needs to export a device "24520:01"
>>>> which pretends all of the things that the gianfar wants (1000Mb/Full/Link)?
>>> Well, this isn't DSA-specific -- e.g. if you'd hook your CPU's
>>> ethernet MAC up to an FPGA, you'd be in the same situation.
>>>
>>> Maybe there is some fake PHY you can instantiate -- the "Fixed"
>>> MDIO bus maybe?  Can you try enabling CONFIG_FIXED_PHY and pointing
>>> it to that?
>> OK, I did that:
>>   Sending discover...
>>   PHY: 0:01 - Link is Up - 1000/Full
>>
>> I now see the fixed PHY (pretender, configured at build time)
>> and the 8 LAN sockets:
>>   root@ppc_target:~ ls /sys/bus/mdio_bus/devices/
>>   0:01         24520:01:01  24520:01:03  24520:01:05  24520:01:07
>>   24520:01:00  24520:01:02  24520:01:04  24520:01:06
>>
>> But nothing seems to get through the switch.  Of course, I
>> know that the switch and connections are working because that's
>> the path I downloaded/booted the kernel from.
>>
>> Getting closer :-) Any ideas?
> 
> :-)  Do you see messages in your syslog about the lan interfaces
> being up, full duplex, etc?  Something a la (from one of my boards):
> 
> 	lan1: link up, 1000 Mb/s, full duplex, flow control disabled
> 	lan2: link up, 1000 Mb/s, full duplex, flow control disabled

This does seem to work:
  root@ppc_target:~ ifconfig lan1.1 up
  root@ppc_target:~ lan1.1: link up, 100 Mb/s, full duplex, flow control disabled

When I try it on other ports:
  root@ppc_target:~ ifconfig lan1.2 up
  root@ppc_target:~ ifconfig lan1.3 up
Those ports aren't plugged (and I'm 6000 miles from them, literally,
so I can't change that)

> If yes, can you up the interfaces, and send some packets over them
> and see if the TX counters on eth0 increase?  If yes, can you dump
> the packets sent out over eth0 using tcpdump?

I tried to ping out and into the box.  Nothing seems to go anywhere:

root@ppc_target:~ ifconfig
eth0      Link encap:Ethernet  HWaddr 00:1D:11:81:00:00
          inet addr:192.168.12.189  Bcast:192.168.12.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:17 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:1810 (1.7 KiB)
          Base address:0x6000

lan1.1    Link encap:Ethernet  HWaddr 00:1D:11:81:00:00
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

Running tcpdump on the external network (192.168.12.x), I saw
no activity.

Do I need to do anything more than "ifconfig lan1.1 up"?
Maybe the "." is confusing things?  I was just trying to
look ahead when I have 3 switches running.

Thanks

-- 
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------