Re: About bittiming calculation result

[Wolfgang Grandegger <wg-5Yr1BZd7O62+XT7JhA+gdA@public.gmane.org>]

On 02/07/2011 01:00 PM, Wolfgang Grandegger wrote:
> Hi Tomoya,
> 
> On 02/07/2011 12:38 PM, Tomoya MORINAGA wrote:
>> Hi,
>>
>> I have a question for bittiming-value calculated by Can-core.
>>
>> In case setting like below,
>>  - ip link set can0 type can bitrate 800000
>>  - clock=50MHz
>>  - Use pch_can
>>
>> Can-core calculates like below
>> brp=21
>> seg1=1
>> seg2=1
>> sjw=1
>> prop_seg=0
>>
>> Is "prop_seg=0" true ?
> 
> Well, only prop_seg+phase_seg=tseg1 is relevant and the pch_can driver
> sets the allowed minimum "tseg1_min1" currently to 1:
> 
> static struct can_bittiming_const pch_can_bittiming_const = {
>         .name = KBUILD_MODNAME,
>         .tseg1_min = 1,
>         .tseg1_max = 16,
>         .tseg2_min = 1,
>         .tseg2_max = 8,
>         .sjw_max = 4,
>         .brp_min = 1,
>         .brp_max = 1024, /* 6bit + extended 4bit */
>         .brp_inc = 1,
> };
> 
>> seg1/seg2/sjw/prop_seg must be more than 1 ?
> 
> Then "tseg1_min" should be set to *2*.
> 
>> Also I can see the following kernel error log.
>> bitrate error 0.7%
> 
> A clock frequency of 50 MHz is sub-optimal for CAN and some
> bit-rates cannot be reproduced properly. Here is the output of
> the can-utils program "can-calc-bit-timing" (with an entry for
> the pch-can added):
> 
> $ ./can-calc-bit-timing pch-can
> Bit timing parameters for pch-can with 50.000000 MHz ref clock
> nominal                                 real Bitrt   nom  real SampP
> Bitrate TQ[ns] PrS PhS1 PhS2 SJW BRP Bitrate Error SampP SampP Error CNF1 CNF2 CNF3
> 1000000    100   3    3    3   1   5 1000000  0.0% 75.0% 70.0%  6.7% 0x05 0x92 0x02
>  800000    420   0    1    1   1  21  793650  0.8% 80.0% 66.6% 16.8% 0x15 0xff 0x00
>  500000    100   8    8    3   1   5  500000  0.0% 87.5% 85.0%  2.9% 0x05 0xbf 0x02
>  250000    500   3    3    1   1  25  250000  0.0% 87.5% 87.5%  0.0% 0x19 0x92 0x00
>  125000    500   6    7    2   1  25  125000  0.0% 87.5% 87.5%  0.0% 0x19 0xb5 0x01
>  100000    500   8    8    3   1  25  100000  0.0% 87.5% 85.0%  2.9% 0x19 0xbf 0x02
>   50000   2500   3    3    1   1 125   50000  0.0% 87.5% 87.5%  0.0% 0x7d 0x92 0x00
>   20000   2500   8    8    3   1 125   20000  0.0% 87.5% 85.0%  2.9% 0x7d 0xbf 0x02
>   10000  12500   3    3    1   1 625   10000  0.0% 87.5% 87.5%  0.0% 0x71 0x92 0x00
> 
> As you can see, especially 800000 gives rather bad results.

BTW, it's always possible to specify optimized bit-timing parameters
directly, e.g. the following seem better:

   800000     60  12    4    4   4   3  793650  0.8% 80.0% 81.0%  1.2%

You could set these with:

  $ ip link set can0 type can \
    tq 60 prop-seg 12 phase-seg1 4 phase-seg2 4 sjw 4

Wolfgang.