Re: [RFC PATCH] core: Add ioctls to control device unicast hw addresses

[John Fastabend <john.fastabend@gmail.com>]

On 02/26/2013 09:42 PM, Jitendra Kalsaria wrote:
>
>
> On 2/26/13 9:01 PM, "John Fastabend" <john.r.fastabend@intel.com> wrote:
>
>> On 2/26/2013 6:27 PM, Vlad Yasevich wrote:
>>> On 02/26/2013 09:07 PM, John Fastabend wrote:
>>>> On Tue, Feb 26, 2013 at 05:15:03PM -0500, David Miller wrote:
>>>>> From: John Fastabend <john.r.fastabend@intel.com>
>>>>> Date: Tue, 26 Feb 2013 13:58:39 -0800
>>>>>
>>>>>> [...]
>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> [RFC PATCH] rtnetlink: Add support for adding/removing additional
>>>>>>>>> hw
>>>>>>>>> addresses.
>>>>>>>>>
>>>>>>>>> Add an ability to add and remove HW addresses to the device
>>>>>>>>> unicast and multicast address lists.  Right now, we only have
>>>>>>>>> an ioctl() to manage the multicast addresses and there is no
>>>>>>>>> way the manage the unicast list.
>>>>>>>>>
>>>>>>>>> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
>>>>>>>>
>>>>>>>> This is a step in the right direction, and you're right that there
>>>>>>>> is
>>>>>>>> a difficulty in detecting whether support exists or not.
>>>>>>>>
>>>>>>>> I am so surprised that we've have ->set_rx_mode() support for
>>>>>>>> multiple
>>>>>>>> unicast MAC addresses in so many drivers all this time, yet no way
>>>>>>>> outside of FDB to make use of it at all.
>>>>>>>
>>>>>>> And even that is not always available.  In most drivers it requires
>>>>>>> module parameters or other explicit configuration steps.  Meanwhile
>>>>>>> set_rx_mode() doesn't seem to depend on any of those and just does
>>>>>>> the
>>>>>>> right thing.
>>>>>>>
>>>>>>> For what I was trying to do ioctl() was a really easy way out for
>>>>>>> both
>>>>>>> kernel and user space implementation, so I gave is shot.
>>>>>>>
>>>>>>> -vlad
>>>>>>>
>>>>>>
>>>>>> Don't we already support this with
>>>>>
>>>>> The whole point is that these multiple-unicast-address configuration
>>>>> facilities are inaccessible without FDB, and there is no reason
>>>>> whatsoever for that.
>>>>
>>>> Yes I see now sorry I was behind the thread.
>>>>
>>>> We could just use the fdb hooks and add a dflt routine to handle the
>>>> case where the netdev doesn't provide a specific ndo_op for us. This
>>>> boils down to calling set_rx_mode anyways through this call chain,
>>>>
>>>>      ndo_fdb_add
>>>>      dev_uc_add_excl
>>>>          __dev_set_rx_mode
>>>>              ndo_set_rx_mode
>>>>
>>>> As long as folks don't think this is too much of an abuse of the fdb
>>>> hooks. Here's an example I only compile tested this so take it as
>>>> an example only. It probably needs some cleanups and the dump routine
>>>> needs some thought not sure you want to dump all MACs always.
>>>
>>> I thought about doing, but this becomes broken on the drivers that
>>> support ndo_fdb_* functions.  Those drivers mainly require additional
>>> configuration that is not necessary for dev_uc_add_excl() to work.
>>>
>>> For example, ixgbe and melanox requires VF to be on, qlogic needs a
>>> module parameter, macvlan has to be in passthrough.  However,
>>> ndo_set_rx_mode() in most cases doesn't care about those settings and
>>> just works.
>>>
>>
>> The ixgbe piece could just use the dflt routines I put below. The
>> SR-IOV check is only there because when I wrote that I didn't consider
>> adding additional addresses without VFs. This was a poor example.
>>
>> The mlx4 card is checking if the device is a slave or master before
>> adding/removing addresses. My guess is this is the same type of check
>> as ixgbe and would work just fine without it.
>>
>> I'm not sure macvlan supports unicast hw addresses either way but
>> there is no reason we couldn't. The idea was we would come back and
>> write it later. Like many things I haven't got to it yet.
>>
>> Calling set_rx_mode() on qlcnic doesn't look to help you at all either
>> it appears to ignore the uc_list either way.
>
> Even though we use module parameter for fdb but it would be good it have
> set_rx_mode().
> We don't ignore uc_list but it never called set_rx_mode() when I use
> dev_uc_add_excl when added support and thought that's how it might
> designed.
>
> -Jiten
>>

Hopefully not too off topic but you probably should use dev_uc_add_excl
in fdb_add and then fix your set_rx_mode() handler to configure the
uc_list correctly. Not sure what happens today when a unicast addr
is added to the list for example with macvlan looks like a bug to me.


.John

-- 
John Fastabend         Intel Corporation