Re: [PATCH regression] net: phy: fix initialization (config_init) for Marvel 88E1116R PHYs

[Alexander Holler <holler@ahsoftware.de>]

Am 02.04.2014 11:09, schrieb Alexander Holler:
> Am 02.04.2014 02:57, schrieb Florian Fainelli:
>> 2014-04-01 16:55 GMT-07:00 Alexander Holler <holler@ahsoftware.de>:
>>> Commit 7cd1463664c2a15721ff4ccfb61d4d970815cb3d (introduced with 3.14)
>>> changed the initialization of the mv643xx_eth driver to use
>>> phy_init_hw()
>>> to reset the PHY. Unfortunately the initialization for the 88E1116R PHY
>>> was broken such, that it used mdelay() instead of really waiting for a
>>> reset to finish.
>>
>> So the only big difference before
>> 7cd1463664c2a15721ff4ccfb61d4d970815cb3d ("net: mv643xx_eth: use
>> phy_init_hw to reset PHY") is that we waited potentially forever for
>> the BMCR_RESET bit to get cleared, while now, we only wait for up to
>> 500 milliseconds.
>>
>> Could you verify the following two things before your patch gets merged:
>>
>> - how long does it take for your PHY to clear the BMCR_RESET bit, is
>> it more than the allowed time out in
>> drivers/net/phy/phy_device.c::phy_poll_reset
>> - is your PHY powered down (check BMCR_PWRDOWN), if that is the case,
>> we might be hitting some corner case where toggling BMCR_RESET will
>> power it on, but at the expense of waiting longer
>
> I've  done two tests with pr_info before and after the two resets in
> m88e1116r_config_init:
>
> with my patch:
> -----------------------
> dmesg | grep -A1 -B1  AHO
> [    1.090099] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version
> 1.4
> [    1.175916] AHO: before first reset
> [    1.179613] AHO: after first reset
> [    1.183743] AHO: before second reset
> [    1.187530] AHO: after second reset
> [    1.191905] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC
> address xx
> --
> [    1.426487] netpoll: netconsole: device eth0 not up yet, forcing it
> [    1.505986] AHO: before first reset
> [    1.509725] AHO: after first reset
> [    1.513899] AHO: before second reset
> [    1.517754] AHO: after second reset
> [    1.521802] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> --
> [   21.372591] Adding 2996116k swap on /dev/sda3.  Priority:-1 extents:1
> across:2996116k
> [   28.305989] AHO: before first reset
> [   28.306200] AHO: after first reset
> [   28.306936] AHO: before second reset
> [   28.307153] AHO: after second reset
> [   31.509973] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000
> Mb/s, full duplex, flow control disabled
> -----------------------
>
>
> with mdelay (the value after reset is what contains MII_BMCR):
>
> -----------------------
> dmesg | grep -A1 -B1  AHO
> [    1.090072] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version
> 1.4
> [    1.175888] AHO: before first reset
> [    1.678806] AHO: after first reset 0x0
> [    1.683281] AHO: before second reset
> [    2.186288] AHO: after second reset 0x0
> [    2.191010] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC
> address xx
> --
> [    2.426349] netpoll: netconsole: device eth0 not up yet, forcing it
> [    2.505917] AHO: before first reset
> [    2.605824] usb 1-1: new high-speed USB device number 2 using orion-ehci
> --
> [    2.829987] hub 1-1:1.0: 4 ports detected
> [    3.044502] AHO: after first reset 0x0
> [    3.049133] AHO: before second reset
> [    3.126110] usb 1-1.1: new high-speed USB device number 3 using
> orion-ehci
> --
> [    3.526107] usb 1-1.3: device descriptor read/64, error -32
> [    3.614264] AHO: after second reset 0x0
> [    3.618708] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
> --
> [   21.335730] Adding 2996116k swap on /dev/sda3.  Priority:-1 extents:1
> across:2996116k
> [   28.195942] AHO: before first reset
> [   28.696270] AHO: after first reset 0x800
> [   28.696958] AHO: before second reset
> [   29.197354] AHO: after second reset 0x800
> [  111.612263] RPC: Registered named UNIX socket transport module.
> -----------------------
>
> So we see, the first reset in the last call of m88e1116r_config_init()
> fails to complete in 500ms and the phy seems to be stuck afterwards,
> but, for whatever reason, it doesn't need 500ms if mdelay isn't used (if
> we can trust the timestamps).
>
> (You can also see, I have netconsole enabled using netconsole=... in the
> kernel cmdline).
>
> That behaviour is reproducible. The first reset in the last call to
> m88e1116r_config_init() always fails if mdelay is used.

I've forgotten to add that MII_BMCR is always zero when 
m88e1116r_config_init() is called.

So to conclude, I've no idea why using mdelay seems to break the PHY. It 
looks like the forced delay of together one second in 
m88e1116r_config_init() somehow breaks something, but that's pure 
speculation. And as my patch fixes things here, I've no reason to dig 
further.

Regards,

Alexander Holler