Re: [RFC PATCH kernel] Revert "net/mlx4_core: Add port attribute when tracking counters"

[Alexey Kardashevskiy <aik@ozlabs.ru>]

On 08/30/2015 04:28 PM, Or Gerlitz wrote:
> On Fri, Aug 28, 2015 at 7:06 AM, Alexey Kardashevskiy <aik@ozlabs.ru> wrote:
>> 68230242cdb breaks SRIOV on POWER8 system. I am not really suggesting
>> reverting the patch, rather asking for a fix.
>
> thanks for the detailed report, we will look into that.
>
> Just to be sure, when going back in time, what is the latest upstream
> version where
> this system/config works okay? is that 4.1 or later?

4.1 is good, 4.2 is not.


>
>>
>> To reproduce it:
>>
>> 1. boot latest upstream kernel (v4.2-rc8 sha1 4941b8f, ppc64le)
>>
>> 2. Run:
>> sudo rmmod mlx4_en mlx4_ib mlx4_core
>> sudo modprobe mlx4_core num_vfs=4 probe_vf=4 port_type_array=2,2 debug_level=1
>>
>> 3. Run QEMU (just to give a complete picture):
>> /home/aik/qemu-system-ppc64 -enable-kvm -m 2048 -machine pseries \
>> -nodefaults \
>> -chardev stdio,id=id0,signal=off,mux=on \
>> -device spapr-vty,id=id1,chardev=id0,reg=0x71000100 \
>> -mon id=id2,chardev=id0,mode=readline -nographic -vga none \
>> -initrd dhclient.cpio -kernel vml400bedbg \
>> -device vfio-pci,id=id3,host=0003:03:00.1
>> What guest is used does not matter at all.
>>
>> 4. Wait till guest boots and then run:
>> dhclient
>> This assigns IPs to both interfaces just fine. This is essential -
>> if interface was not brought up since guest started, the bug does not appear.
>> If interface was up and then down, this still causes the problem
>> (less likely though).
>>
>> 5. Run in the guest: shutdown -h 0
>> Guest prints:
>> mlx4_en: eth0: Close port called
>> mlx4_en: eth1: Close port called
>> mlx4_core 0000:00:00.0: mlx4_shutdown was called
>> And then the host hangs. After 10-30 seconds the host console prints:
>> NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [qemu-system-ppc:5095]
>> OR
>> INFO: rcu_sched detected stalls on CPUs/tasks:
>> or some other random stuff but always related to some sort of lockup.
>> Backtraces are like these:
>>
>> [c000001e492a7ac0] [c000000000135b84] smp_call_function_many+0x2f4/0x3fable)
>> [c000001e492a7b40] [c000000000135db8] kick_all_cpus_sync+0x38/0x50
>> [c000001e492a7b60] [c000000000048f38] pmdp_huge_get_and_clear+0x48/0x70
>> [c000001e492a7b90] [c00000000023181c] change_huge_pmd+0xac/0x210
>> [c000001e492a7bf0] [c0000000001fb9e8] change_protection+0x678/0x720
>> [c000001e492a7d00] [c000000000217d38] change_prot_numa+0x28/0xa0
>> [c000001e492a7d30] [c0000000000e0e40] task_numa_work+0x2a0/0x370
>> [c000001e492a7db0] [c0000000000c5fb4] task_work_run+0xe4/0x160
>> [c000001e492a7e00] [c0000000000169a4] do_notify_resume+0x84/0x90
>> [c000001e492a7e30] [c0000000000098b8] ret_from_except_lite+0x64/0x68
>>
>> OR
>>
>> [c000001def1b7280] [c000000ff941d368] 0xc000000ff941d368 (unreliable)
>> [c000001def1b7450] [c00000000001512c] __switch_to+0x1fc/0x350
>> [c000001def1b7490] [c000001def1b74e0] 0xc000001def1b74e0
>> [c000001def1b74e0] [c00000000011a50c] try_to_del_timer_sync+0x5c/0x90
>> [c000001def1b7520] [c00000000011a590] del_timer_sync+0x50/0x70
>> [c000001def1b7550] [c0000000009136fc] schedule_timeout+0x15c/0x2b0
>> [c000001def1b7620] [c000000000910e6c] wait_for_common+0x12c/0x230
>> [c000001def1b7660] [c0000000000fa22c] up+0x4c/0x80
>> [c000001def1b76a0] [d000000016323e60] __mlx4_cmd+0x320/0x940 [mlx4_core]
>> [c000001def1b7760] [c000001def1b77a0] 0xc000001def1b77a0
>> [c000001def1b77f0] [d0000000163528b4] mlx4_2RST_QP_wrapper+0x154/0x1e0 [mlx4_core]
>> [c000001def1b7860] [d000000016324934] mlx4_master_process_vhcr+0x1b4/0x6c0 [mlx4_core]
>> [c000001def1b7930] [d000000016324170] __mlx4_cmd+0x630/0x940 [mlx4_core]
>> [c000001def1b79f0] [d000000016346fec] __mlx4_qp_modify.constprop.8+0x1ec/0x350 [mlx4_core]
>> [c000001def1b7ac0] [d000000016292228] mlx4_ib_destroy_qp+0xd8/0x5d0 [mlx4_ib]
>> [c000001def1b7b60] [d000000013c7305c] ib_destroy_qp+0x1cc/0x290 [ib_core]
>> [c000001def1b7bb0] [d000000016284548] destroy_pv_resources.isra.14.part.15+0x48/0xf0 [mlx4_ib]
>> [c000001def1b7be0] [d000000016284d28] mlx4_ib_tunnels_update+0x168/0x170 [mlx4_ib]
>> [c000001def1b7c20] [d0000000162876e0] mlx4_ib_tunnels_update_work+0x30/0x50 [mlx4_ib]
>> [c000001def1b7c50] [c0000000000c0d34] process_one_work+0x194/0x490
>> [c000001def1b7ce0] [c0000000000c11b0] worker_thread+0x180/0x5a0
>> [c000001def1b7d80] [c0000000000c8a0c] kthread+0x10c/0x130
>> [c000001def1b7e30] [c0000000000095a8] ret_from_kernel_thread+0x5c/0xb4
>>
>> i.e. may or may not mention mlx4.
>> The issue may not happen on a first try but maximum on the second.
>
> so when you revert commit 68230242cdb on the host all works just fine?
> what guest driver are you running?

To be precise, I did checkout 68230242cdb, checked that it does not work, 
then reverted 68230242cdb right there and checked that it works. I did not 
try reverting later revisions yet.

My guest kernel in this test has tag v4.0. I get the same effect with some 
3.18 from Ubuntu 14.04 LTS so the guest kernel version does not make a 
difference afaict.


> This needs a fix, I don't think the right thing to do is just go and
> revert the commit, if the right fix misses 4.2 we will get it there
> through -stable

v4.2 was just released :)


-- 
Alexey