From: "Samudrala, Sridhar" <sridhar.samudrala@intel.com>
To: Jeff Kirsher <jeffrey.t.kirsher@intel.com>, davem@davemloft.net
Cc: Alexander Duyck <aduyck@mirantis.com>,
netdev@vger.kernel.org, nhorman@redhat.com, sassmann@redhat.com,
jogreene@redhat.com
Subject: Re: [net-next 08/14] ixgbe: Add support for generic Tx checksums
Date: Mon, 04 Apr 2016 15:32:37 -0700 [thread overview]
Message-ID: <5702EB85.5080307@intel.com> (raw)
In-Reply-To: <1459808097-26409-9-git-send-email-jeffrey.t.kirsher@intel.com>
On 4/4/2016 3:14 PM, Jeff Kirsher wrote:
> From: Alexander Duyck <aduyck@mirantis.com>
>
> This patch adds support for generic Tx checksums to the ixgbe driver. It
> turns out this is actually pretty easy after going over the datasheet as we
> were doing a number of steps we didn't need to.
>
> In order to perform a Tx checksum for an L4 header we need to fill in the
> following fields in the Tx descriptor:
> MACLEN (maximum of 127), retrieved from:
> skb_network_offset()
> IPLEN (maximum of 511), retrieved from:
> skb_checksum_start_offset() - skb_network_offset()
> TUCMD.L4T indicates offset and if checksum or crc32c, based on:
> skb->csum_offset
>
> The added advantage to doing this is that we can support inner checksum
> offloads for tunnels and MPLS while still being able to transparently
> insert VLAN tags.
>
> I also took the opportunity to clean-up many of the feature flag
> configuration bits to make them a bit more consistent between drivers.
>
> Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
> Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
> ---
> drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 164 +++++++++-----------------
> 1 file changed, 59 insertions(+), 105 deletions(-)
>
> diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
> index bce5737..8d248c8 100644
> --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
> +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
> @@ -7202,103 +7202,61 @@ static int ixgbe_tso(struct ixgbe_ring *tx_ring,
> return 1;
> }
>
<snip>
> @@ -9190,41 +9148,37 @@ skip_sriov:
>
> #endif
> netdev->features = NETIF_F_SG |
> - NETIF_F_IP_CSUM |
> - NETIF_F_IPV6_CSUM |
> - NETIF_F_HW_VLAN_CTAG_TX |
> - NETIF_F_HW_VLAN_CTAG_RX |
> NETIF_F_TSO |
> NETIF_F_TSO6 |
> NETIF_F_RXHASH |
> - NETIF_F_RXCSUM;
> -
> - netdev->hw_features = netdev->features | NETIF_F_HW_L2FW_DOFFLOAD;
> + NETIF_F_RXCSUM |
> + NETIF_F_HW_CSUM |
> + NETIF_F_SCTP_CRC |
> + NETIF_F_HW_VLAN_CTAG_TX |
> + NETIF_F_HW_VLAN_CTAG_RX;
>
> - switch (adapter->hw.mac.type) {
> - case ixgbe_mac_82599EB:
> - case ixgbe_mac_X540:
> - case ixgbe_mac_X550:
> - case ixgbe_mac_X550EM_x:
> + if (hw->mac.type >= ixgbe_mac_82599EB)
> netdev->features |= NETIF_F_SCTP_CRC;
> - netdev->hw_features |= NETIF_F_SCTP_CRC |
> - NETIF_F_NTUPLE |
> - NETIF_F_HW_TC;
> - break;
> - default:
> - break;
> - }
>
> - netdev->hw_features |= NETIF_F_RXALL;
> + /* copy netdev features into list of user selectable features */
> + netdev->hw_features |= netdev->features;
> + netdev->hw_features |= NETIF_F_RXALL |
> + NETIF_F_HW_L2FW_DOFFLOAD;
> +
> + if (hw->mac.type >= ixgbe_mac_82599EB)
> + netdev->hw_features |= NETIF_F_NTUPLE;
looks like the cleanup missed moving NETIF_F_HW_TC flag here that
enables cls_u32 offloads via TC.
> +
> + /* set this bit last since it cannot be part of hw_features */
> netdev->features |= NETIF_F_HW_VLAN_CTAG_FILTER;
>
> - netdev->vlan_features |= NETIF_F_TSO;
> - netdev->vlan_features |= NETIF_F_TSO6;
> - netdev->vlan_features |= NETIF_F_IP_CSUM;
> - netdev->vlan_features |= NETIF_F_IPV6_CSUM;
> - netdev->vlan_features |= NETIF_F_SG;
> + netdev->vlan_features |= NETIF_F_SG |
> + NETIF_F_TSO |
> + NETIF_F_TSO6 |
> + NETIF_F_HW_CSUM |
> + NETIF_F_SCTP_CRC;
>
> - netdev->hw_enc_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
> + netdev->mpls_features |= NETIF_F_HW_CSUM;
> + netdev->hw_enc_features |= NETIF_F_HW_CSUM;
>
> netdev->priv_flags |= IFF_UNICAST_FLT;
> netdev->priv_flags |= IFF_SUPP_NOFCS;
next prev parent reply other threads:[~2016-04-04 22:32 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-04-04 22:14 [net-next 00/14][pull request] 10GbE Intel Wired LAN Driver Updates 2016-04-04 Jeff Kirsher
2016-04-04 22:14 ` [net-next 01/14] ixgbe: on recv increment rx.ring->stats.yields Jeff Kirsher
2016-04-04 22:14 ` [net-next 02/14] ixgbevf: use bit operations for setting and checking resets Jeff Kirsher
2016-04-04 22:14 ` [net-next 03/14] ixgbe: Extend trust to allow guest to set unicast address Jeff Kirsher
2016-04-04 22:14 ` [net-next 04/14] ixgbe: Do not allow PF to add VLVF entry unless it actually needs it Jeff Kirsher
2016-04-04 22:14 ` [net-next 05/14] ixgbe: Avoid adding VLAN 0 twice to VLVF and VFTA Jeff Kirsher
2016-04-04 22:14 ` [net-next 06/14] ixgbe: Make all unchanging ops structures const Jeff Kirsher
2016-04-04 22:14 ` [net-next 07/14] ixgbe: use eth_platform_get_mac_address() Jeff Kirsher
2016-04-04 22:14 ` [net-next 08/14] ixgbe: Add support for generic Tx checksums Jeff Kirsher
2016-04-04 22:32 ` Samudrala, Sridhar [this message]
2016-04-04 22:54 ` Alexander Duyck
2016-04-04 22:56 ` Jeff Kirsher
2016-04-05 1:27 ` David Miller
2016-04-05 1:29 ` Jeff Kirsher
2016-04-04 22:14 ` [net-next 09/14] ixgbevf: " Jeff Kirsher
2016-04-04 22:14 ` [net-next 10/14] ixgbe: Fix flow control for Xeon D KR backplane Jeff Kirsher
2016-04-04 22:14 ` [net-next 11/14] ixgbe: add a callback to set the maximum transmit bitrate Jeff Kirsher
2016-04-04 22:14 ` [net-next 12/14] ixgbe: Place SWFW semaphore in known valid state at probe Jeff Kirsher
2016-04-04 22:14 ` [net-next 13/14] ixgbe: Extend cls_u32 offload to support UDP headers Jeff Kirsher
2016-04-04 22:14 ` [net-next 14/14] ixgbe: Add support for toggling VLAN filtering flag via ethtool Jeff Kirsher
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5702EB85.5080307@intel.com \
--to=sridhar.samudrala@intel.com \
--cc=aduyck@mirantis.com \
--cc=davem@davemloft.net \
--cc=jeffrey.t.kirsher@intel.com \
--cc=jogreene@redhat.com \
--cc=netdev@vger.kernel.org \
--cc=nhorman@redhat.com \
--cc=sassmann@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).