Re: [PATCH net] Revert "net: phy: Correctly process PHY_HALTED in phy_stop_machine()"

[Florian Fainelli <f.fainelli@gmail.com>]

On 09/06/2017 11:00 AM, David Daney wrote:
> On 08/31/2017 11:29 AM, Florian Fainelli wrote:
>> On 08/31/2017 11:12 AM, Mason wrote:
>>> On 31/08/2017 19:53, Florian Fainelli wrote:
>>>> On 08/31/2017 10:49 AM, Mason wrote:
>>>>> On 31/08/2017 18:57, Florian Fainelli wrote:
>>>>>> And the race is between phy_detach() setting phydev->attached_dev
>>>>>> = NULL
>>>>>> and phy_state_machine() running in PHY_HALTED state and calling
>>>>>> netif_carrier_off().
>>>>>
>>>>> I must be missing something.
>>>>> (Since a thread cannot race against itself.)
>>>>>
>>>>> phy_disconnect calls phy_stop_machine which
>>>>> 1) stops the work queue from running in a separate thread
>>>>> 2) calls phy_state_machine *synchronously*
>>>>>       which runs the PHY_HALTED case with everything well-defined
>>>>> end of phy_stop_machine
>>>>>
>>>>> phy_disconnect only then calls phy_detach()
>>>>> which makes future calls of phy_state_machine perilous.
>>>>>
>>>>> This all happens in the same thread, so I'm not yet
>>>>> seeing where the race happens?
>>>>
>>>> The race is as described in David's earlier email, so let's recap:
>>>>
>>>> Thread 1            Thread 2
>>>> phy_disconnect()
>>>> phy_stop_interrupts()
>>>> phy_stop_machine()
>>>> phy_state_machine()
>>>>   -> queue_delayed_work()
>>>> phy_detach()
>>>>                 phy_state_machine()
>>>>                 -> netif_carrier_off()
>>>>
>>>> If phy_detach() finishes earlier than the workqueue had a chance to be
>>>> scheduled and process PHY_HALTED again, then we trigger the NULL
>>>> pointer
>>>> de-reference.
>>>>
>>>> workqueues are not tasklets, the CPU scheduling them gets no guarantee
>>>> they will run on the same CPU.
>>>
>>> Something does not add up.
>>>
>>> The synchronous call to phy_state_machine() does:
>>>
>>>     case PHY_HALTED:
>>>         if (phydev->link) {
>>>             phydev->link = 0;
>>>             netif_carrier_off(phydev->attached_dev);
>>>             phy_adjust_link(phydev);
>>>             do_suspend = true;
>>>         }
>>>
>>> then sets phydev->link = 0; therefore subsequent calls to
>>> phy_state_machin() will be no-op.
>>
>> Actually you are right, once phydev->link is set to 0 these would become
>> no-ops. Still scratching my head as to what happens for David then...
>>
>>>
>>> Also, queue_delayed_work() is only called in polling mode.
>>> David stated that he's using interrupt mode.
> 
> Did you see what I wrote?

Still not following, see below.

> 
> phy_disconnect() calls phy_stop_interrupts() which puts it into polling
> mode.  So the polling work gets queued unconditionally.

What part of phy_stop_interrupts() is responsible for changing
phydev->irq to PHY_POLL? free_irq() cannot touch phydev->irq otherwise
subsequent request_irq() calls won't work anymore.
phy_disable_interrupts() only calls back into the PHY driver to
acknowledge and clear interrupts.

If we were using a PHY with PHY_POLL, as Marc said, the first
synchronous call to phy_state_machine() would have acted on PHY_HALTED
and even if we incorrectly keep re-scheduling the state machine from
PHY_HALTED to PHY_HALTED the second time around nothing can happen.

What are we missing here?

> 
> 
> 
>>
>> Right that's confusing too now. David can you check if you tree has:
>>
>> 49d52e8108a21749dc2114b924c907db43358984 ("net: phy: handle state
>> correctly in phy_stop_machine")
>>
> 
> Yes, I am using the 4.9 stable branch, and that commit was also present.

Thanks for checking that.
-- 
Florian