From: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
To: Jamal Hadi Salim <jhs@mojatatu.com>, davem@davemloft.net
Cc: netdev@vger.kernel.org, xiyou.wangcong@gmail.com, daniel@iogearbox.net
Subject: Re: [PATCH net-next 1/1] net sched actions: mirred add support for setting Dst MAC address
Date: Sat, 2 Jul 2016 16:07:51 +0200 [thread overview]
Message-ID: <5777CAB7.9050007@cumulusnetworks.com> (raw)
In-Reply-To: <5777C976.4000402@mojatatu.com>
On 02/07/16 16:02, Jamal Hadi Salim wrote:
> On 16-07-02 09:49 AM, Nikolay Aleksandrov wrote:
>> On 02/07/16 15:26, Jamal Hadi Salim wrote:
>>> From: Jamal Hadi Salim <jhs@mojatatu.com>
>>>
>>> Often redirecting or mirroring requires that we set the MAC address
>>> of the target device. While it is possible to pipe to a pedit action
>>> this obsoletes the need for that. This is justified feature because
>>> the dst MAC addresses rewrite is such a common use case.
>>>
>>> Sample usage:
>>> sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 \
>>> u32 match ip protocol 1 0xff flowid 1:2 \
>>> action mirred egress redirect dev $SPANPORT dst 02:15:15:15:15:15
>>>
>>> This will match all icmp packets going out on dev $ETH and
>>> redirect them to dev $SPANPORT while setting their dst MAC address
>>> to 02:15:15:15:15:15
>>>
>>> Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
>>> ---
>>> include/net/tc_act/tc_mirred.h | 4 +++-
>>> include/uapi/linux/tc_act/tc_mirred.h | 7 ++++---
>>> net/sched/act_mirred.c | 20 +++++++++++++++++++-
>>> 3 files changed, 26 insertions(+), 5 deletions(-)
>>>
>>> diff --git a/include/net/tc_act/tc_mirred.h b/include/net/tc_act/tc_mirred.h
>>> index e891835..7e8bced 100644
>>> --- a/include/net/tc_act/tc_mirred.h
>>> +++ b/include/net/tc_act/tc_mirred.h
>>> @@ -6,10 +6,12 @@
>>>
>>> struct tcf_mirred {
>>> struct tcf_common common;
>>> + struct net_device __rcu *tcfm_dev;
>>> int tcfm_eaction;
>>> int tcfm_ifindex;
>>> int tcfm_ok_push;
>>> - struct net_device __rcu *tcfm_dev;
>>> + u8 eth_dst[ETH_ALEN];
>>> + /* XXX 6 bytes hole here*/
>>> struct list_head tcfm_list;
>>> };
>>> #define to_mirred(a) \
>>> diff --git a/include/uapi/linux/tc_act/tc_mirred.h b/include/uapi/linux/tc_act/tc_mirred.h
>>> index 3d7a2b3..aaca1ff 100644
>>> --- a/include/uapi/linux/tc_act/tc_mirred.h
>>> +++ b/include/uapi/linux/tc_act/tc_mirred.h
>>> @@ -9,20 +9,21 @@
>>> #define TCA_EGRESS_MIRROR 2 /* mirror packet to EGRESS */
>>> #define TCA_INGRESS_REDIR 3 /* packet redirect to INGRESS*/
>>> #define TCA_INGRESS_MIRROR 4 /* mirror packet to INGRESS */
>>> -
>>> +
>>> struct tc_mirred {
>>> tc_gen;
>>> int eaction; /* one of IN/EGRESS_MIRROR/REDIR */
>>> __u32 ifindex; /* ifindex of egress port */
>>> };
>>> -
>>> +
>>> enum {
>>> TCA_MIRRED_UNSPEC,
>>> TCA_MIRRED_TM,
>>> TCA_MIRRED_PARMS,
>>> TCA_MIRRED_PAD,
>>> + TCA_MIRRED_DMAC,
>>
>> Hi Jamal,
>> I think you should update "mirred_policy" in order to ensure that the attribute has
>> the minimum length for a mac address.
>
> Good point. Will do in the next update.
>
>> Also a minor suggestion - maybe err out on a
>> zero mac address, otherwise the user might think the operation was successful.
>>
>
> Is a zero mac address wrong? What if that was policy intent?
>
If you mean that you give the user ability to get rid of the mac, then okay. I said it
because it will seem like a successful operation and then the mac will not be dumped
or overwritten which will look like it wasn't set at all.
> cheers,
> jamal
>
next prev parent reply other threads:[~2016-07-02 14:07 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-07-02 13:26 [PATCH net-next 1/1] net sched actions: mirred add support for setting Dst MAC address Jamal Hadi Salim
2016-07-02 13:49 ` Nikolay Aleksandrov
2016-07-02 14:02 ` Jamal Hadi Salim
2016-07-02 14:07 ` Nikolay Aleksandrov [this message]
2016-07-02 14:16 ` Jamal Hadi Salim
2016-07-02 14:26 ` Jamal Hadi Salim
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5777CAB7.9050007@cumulusnetworks.com \
--to=nikolay@cumulusnetworks.com \
--cc=daniel@iogearbox.net \
--cc=davem@davemloft.net \
--cc=jhs@mojatatu.com \
--cc=netdev@vger.kernel.org \
--cc=xiyou.wangcong@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox