Re: [Intel-wired-lan] [net-next PATCH v2 2/6] i40e: Introduce VF Port Representator(VFPR) netdevs.

["Samudrala, Sridhar" <sridhar.samudrala@intel.com>]

On 1/5/2017 1:46 PM, Jeff Kirsher wrote:
> On Tue, 2017-01-03 at 10:07 -0800, Sridhar Samudrala wrote:
>> VF Port Representator netdevs are created for each VF if the switch mode
>> is set to 'switchdev'. These netdevs can be used to control and configure
>> VFs from PFs namespace. They enable exposing VF statistics, configure and
>> monitor link state, mtu, filters, fdb/vlan entries etc. of VFs.
>> Broadcast filters are not enabled in switchdev mode.
>>
>> Sample script to create VF port representors
>> # rmmod i40e; modprobe i40e
>> # devlink dev eswitch set pci/0000:05:00.0 mode switchdev
>> # echo 2 > /sys/class/net/enp5s0f0/device/sriov_numvfs
>> # ip l show
>> 297: enp5s0f0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop portid
>> 6805ca2e7268 state DOWN mode DEFAULT group default qlen 1000
>>       link/ether 68:05:ca:2e:72:68 brd ff:ff:ff:ff:ff:ff
>>       vf 0 MAC 00:00:00:00:00:00, spoof checking on, link-state auto,
>> trust off
>>       vf 1 MAC 00:00:00:00:00:00, spoof checking on, link-state auto,
>> trust off
>> 299: enp5s0f0-vf0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
>> mode DEFAULT group default qlen 1000
>>       link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
>> 300: enp5s0f0-vf1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
>> mode DEFAULT group default qlen 1000
>>       link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff
>>
>> Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
>> ---
>>   drivers/net/ethernet/intel/i40e/i40e_main.c        |  21 ++-
>>   drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c | 154
>> ++++++++++++++++++++-
>>   drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.h |  14 ++
>>   3 files changed, 182 insertions(+), 7 deletions(-)
> This does not apply cleanly because it is based on an older version of
> i40e_virtchnl_pf.c file.  It appears that i40e has been updated to use
> "i40e_add_filter()" yet your patch still uses "i40e_add_mac_filter()".
I am not using i40e_add_mac_filter() in my patches. I only i40e_add_filter()
These patches are against davem's net-next kernel

>
> We need to clarify what the "right way" is to add filters and use the
> correct function.
>
> Dropping this series and will await v3, please address the other feedback
> from Or Gerlitz and Jiri Pirko as well in your updated series.

Sure. I will be submitting a v3 soon addressing the review comments.