Re: [PATCH v3 net-next 1/3] net: enetc: set the external PHY address in IERB for port MDIO usage

[Alexander Stein <alexander.stein@ew.tq-group.com>]

Hi,

Am Samstag, 28. Februar 2026, 04:52:01 CET schrieb Wei Fang:
> > > +static int imx95_enetc_mdio_phyaddr_config(struct platform_device
> > > +*pdev) {
> > > +	struct netc_blk_ctrl *priv = platform_get_drvdata(pdev);
> > > +	struct device_node *np = pdev->dev.of_node;
> > > +	struct device *dev = &pdev->dev;
> > > +	int bus_devfn, addr, err;
> > > +	u32 phy_mask = 0;
> > > +
> > > +	err = netc_get_emdio_phy_mask(np, &phy_mask);
> > > +	if (err) {
> > > +		dev_err(dev, "Failed to get PHY address mask\n");
> > > +		return err;
> > > +	}
> > > +
> > > +	/* Update the port EMDIO PHY address through parsing phy properties.
> > > +	 * This is needed when using the port EMDIO but it's harmless when
> > > +	 * using the central EMDIO. So apply it on all cases.
> > > +	 */
> > > +	for_each_child_of_node_scoped(np, child) {
> > > +		for_each_child_of_node_scoped(child, gchild) {
> > > +			if (!of_device_is_compatible(gchild, "pci1131,e101"))
> > > +				continue;
> > > +
> > > +			bus_devfn = netc_of_pci_get_bus_devfn(gchild);
> > > +			if (bus_devfn < 0) {
> > > +				dev_err(dev, "Failed to get BDF number\n");
> > > +				return bus_devfn;
> > > +			}
> > > +
> > > +			addr = netc_get_phy_addr(gchild);
> > > +			if (addr < 0) {
> > > +				dev_err(dev, "Failed to get PHY address\n");
> > > +				return addr;
> > > +			}
> > > +
> > > +			if (phy_mask & BIT(addr)) {
> > 
> > ... which will break here if there is an Ethernet PHY using address 0 in
> > 'netc_emdio' node.
> > See arch/arm64/boot/dts/freescale/imx95-tqma9596sa.dtsi node
> > ethernet-phy@0.
> 
> AFAIU, the PHY address 0 is a special address, below is the description of
> PHYAD from IEEE 802.3 Clause 22.
> 
> A PHY that is connected to the station management entity via the
> mechanical interface defined in 22.6 shall always respond to transactions
> addressed to PHY Address zero <00000>. A station management entity
> that is attached to multiple PHYs must have prior knowledge of the 
> appropriate PHY Address for each PHY.
> 
> Therefore, for most PHYs, PHY address 0 is typically used as the broadcast
> address or default response address. In designs that control multiple PHYs
> via EMDIO, it is recommended to avoid setting a specific PHY to address 0
> to prevent bus conflicts.

I know about this special meaning, but there are hardware design which do not
take this into account.

> If the PHY on your board does not use PHY address 0 as the broadcast address
> or the default response address, then we should check the PHY address first and
> then check the phy_mask in imx95_enetc_mdio_phyaddr_config(), just the same
> as imx94_enetc_mdio_phyaddr_config().

I'm not sure if this is the right fix. What about the case where phy_mask is
supposed to be 0, because there are no PHY subnodes of netc_emdio. Instead
the PHY with address is a subnode of the enet_portX is supposed to have
netc_get_phy_addr() return 0 because that's the actual address. But with
the current flow from imx94_enetc_mdio_phyaddr_config() and your suggestion
for i.MX95 case we erroneously skip that node.

Best regards,
Alexander
-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/